The series Qosmio G20 does support PC2-5300?

Similar Questions

• The model Interface Toolkit does support the cRIO-9068 again based on Linux?

  Hello, I have a cRIO-9068 and need to integrate a Simulink model in my controller. The model Interface Toolkit does support the cRIO-9068 again based on Linux? Besides, don't Veristand? This page assumes that it is not:

  http://digital.NI.com/public.nsf/allkb/2AE33E926BF2CDF2862579880079D751

  Thank you

  Hi Southern_Cross,

  Based on the readme:

  http://digital.NI.com/public.nsf/allkb/D3F40C101B66128186257D020049D679

  It seems that it is now supported! These resources should provide a few more details:

  http://zone.NI.com/reference/en-XX/help/374160B-01/vsmithelp/mit_model_support/

  http://digital.NI.com/public.nsf/allkb/E552B0CD4E48215586257DF7005BE055

  Please note that NI VeriStand 2014 can't stand it targets NOR Linux in real time.

  Kind regards

• The Compaq Presario CQ41 does support 64 bit OS?

  I went in a chain retailer and I noticed the Compaq Presario CQ41 was running Windows 7 Home Premium 32 bit, but had 4 GB of RAM installed (which he could not fully use). The stafff I asked why and they said HP/Compaq laptops cannot run 64-bit.

  The Compaq Presario CQ41 does support 64-bit so it can used the entire 4 GB of ram?

  The Compaq Presario CQ41 will also support a 64-bit Windows 7 operating system.

• Internal TV tuner for the Qosmio G20 does not work

  I have a qosmio G20 and the built in TV does not work, I reinstalled the driver and the program windvr 5 but no response.
  Whenever I start the program, I can't use the installer.
  Please can someone help me?

  Hello

  Qosmio G20 was delivered with Windows MCE.
  You can also use the Media Center Microsoft watch TV on the laptop!

  Please check if the built-in TV tuner works with MCE. If so, there is nothing wrong with the tuner or the drivers!

  Best regards

• Qosmio G20 does not start

  Hello

  Something is happening with my Qosmio G20.
  Sometimes when I connect the plug to the computer the DC IN indicator flashes orange and the pc does not start.
  A few hours later I try again and now DC IN indicator shows blue and I can boot my pc and I normally work for hours.
  It's very strange. It happens regularly. A few days shows blue and works very well and some other orange flashes of days and I can't work and I have to keep trying to connect and disconnect until it flashes blue to put on.

  Wouldn't be DC Power Charger malfunction? I've already ordered another of DC power charger to confirm, but my intuition says that is not the problem of the charger.
  I remember the 1st time that never happen... I was charging my iPod through my Qosmio and out of the House and let it load it. When I arrived home, the laptop power light flashes orange and I thought it was in hibernation mode. But after that time it started to happen.
  Before trying the new charger and reflections before sending it to the dealer?

  Thank you

  > Sometimes when I connect the plug to the computer the DC IN indicator flashes orange and the pc does not start.
  A few hours later I try again and now DC IN indicator shows blue and I can boot my pc and I normally work for hours.
  It's very strange. It happens regularly. A few days shows blue and works very well and some other orange flashes of days and I can't work and I have to keep trying to connect and disconnect until it flashes blue for setting on

  This flashing provides an error code which means that an error has been detected on the motherboard.
  It is difficult to say what could be possibly wrong power supply to electronic malfunction
  But this is only my personal opinion

  You should certainly contact someone who could verify the material and can run diagnostics tests

• Upgrade my processor from Pentium M740 for the M780 Qosmio G20?

  Hi all!

  Well I just wanted to know if it was possible to upgrade my CPU Intel Pentium M 740 at the 780?

  List of Pentium M processor specification
  http://www.Intel.com/products/Proces.../pentium_m.htm

  Thanks in advance!

  Best regards

  Sylvain

  EDIT: I got a G20-123 *.

  Hello

  Hmm, I found different Qosmio G20 units with different CPUs:
  Intel Mobile Pentium M M Pentium

  1.60 GHz (processor number; 730)
  1.73GHz (processor number; 740)
  1.86 GHz (processor number; 750)
  2.00GHz (processor number; 760)
  2.13 GHz (processor number; 770)

  All these media P Mobile CPU FSB: 533 MHz
  Theoretically, the P - M 780 would be compatible with the motherboard but practically it s always another story.

  The point is that the G20 was not equipped with the P - M 780 CPU and so nobody knows if the BIOS supports this new processor.
  In addition he s always risky to remove these high-tech notebooks. It may be damaged parts.

  That is why it s really not advisable to do this.

  That s in my opinion

• Qosmio F750 does support NVIDEA 3D Vision with glasses?

  Hallo!

  the portable actiually supports 3D without glasses. But I have another question:
  the F750 does support 3D * with * glasses? I want to wear glasses from NVIDEA 3D Vision. According to NVIDIA, specification for the glasses the F750 must be supported. But I can't put the 3D mode. I installed the new dreiver and BIOS 2.0. In framework of NVIDEA is now 3D appeared. To achieve a 3D mode it is necessary to adjust the 120 Hz display, but I can choose 60 Hz only.

  Can you help me please!

  Kind regards
  Doxtor

  > To achieve a 3D mode it is necessary to adjust the 120 Hz display, but I can choose 60 Hz only.

  So this is not supported would need an external monitor that supports the 120 Hz

• ATA-associated message will appear after the stop of the series Qosmio G-start

  Good computer worked fine, but earlier when I tried to start it it just freezes on the start QOSMIO screen and will not continue.

  I can not press F8 and choose how to start and the HARD drive on the computer light remains solid. After leaving it for about 1 minute, I get the following message.

  ATA ERROR #0

  ERROR ATA #1

  any help would be appreciated, thanks

  Hello

  That sounds really serious. You can try to reset the bios by default (refer to the operating manual how to do) and then try to start it again.

  Otherwise, the only thing you could do is to bring the machine to a local service for a hardwarecheckup partner (or repair).

  Would appreciate some comments

• The e2000 wireless router does support jumbo frames?

  I can't find (unless I missed it) and in the e2000 on how documentation set sizes of frame of reference.  Is that supported?  If so, what are the steps?

  A fact important is jumbo frames are not compatible at a speed lower than 1000 Mbps

  I think that Linksys E2000 already has Gigabit Ethernet ports.

  And I think that you can change the size of the image on the properties of the Ethernet adapter if the card is a Gigabit Ethernet card.

• The last version, 23, does support the Roboform toolbar?

  I use my ROBOFORM toolbar every day. If I switch to Firefox 23 going to work again?

  I use the Version of RoboForm 7.9.0.0 and works very well with FireFox 23.0.1

  No problem

• Carpet * a UJ-820 s series Qosmio F does not work...

  It has happened now, and I can't play any CD or DVD.

  I checked his status, but there is not an error...

  What should I do?

  If the warranty is still valid, contact the customer Service of your country partner and explain the situation. They check the disc. If defective it should be replaced for free.

• The HP OfficeJet 6700 does support fax through a line of digital phone to StarHub in Singapore?

  I get my phone line at home to Singapore's StarHub over a digital phone network. My HP OfficeJet 6700 will be able to send and receive faxes on this network?

  Hello rabbers,

  Welcome to the HP Forums.

  I see that you do not want to be able to send / receive faxes via Starhub digital voice line.

  Actually, I should say no. This would work sporadically on a digital line, but no guarantee that it will work all the time.  Faxing is intended for older analogue lines and aimed at all ever for digital.

  Here is a link that will give you instructions for setting up the device HP all-in-one to send and receive faxes.

  Thanks for your time.

  See you soon,.

• Ports 10/100/1000 on the cisco 2911 router does support etherchannel

  Hello

  I need like below

  -Ethernet point to point leased - Line1

  --------Trunk-------- 2911 Router                                                                                          2911 Router-------Trunk-------------

  -Ethernet point to point leased - Line2

  I intend to use existing 3 onboard 10/100/1000 ports router 2911 for a configuration of trunk and etherchannel. Trunk connects to local lan conncts and etherchannel for remote sites. My doubt is can I configure 2911 as trunk ports on board and implement etherchannel? From now on, there will be no routing configuration in 2911.

  Concerning

  Siva K

  Hi Siva,

  > As of now, there is no routing configuration in 2911.

  use a LAN switch for this or an etherswitch module installed in routers C2911

  routed ports can be used only routed or bridiging (IRB) ports, you cannot configure the as trunks of L2, you can use them as a L3 port channel but not as a port-channel trunk L2.

  Hope to help

  Giuseppe

• The UCS B200 M3 does support Windows 2003?

  For compatibility with older existing software, I would know what (assuming that Microsoft extended until 2015 Support contract)

  Kind regards

  Geert

  Hi Geert,

  No, it is not supported.

  http://www.Cisco.com/en/us/products/ps10477/prod_technical_reference_list.html

  Padma

• The extension framework CC does support WebGL?

  Hi all, last time I created extensions for Photoshop was for the beta version of CS4 so much has changed!

  At the time I created a few using Pixelbender effects to create a shader, and then applied to a movieclip and everything was fine.  Even if this was a hack because I wanted to make a glowing sphere, but had to settle for a normal of a sphere of shading map.  I wanted to start where I left off and you just created a quick test Panel, trying to draw a triangle on a canvas with the help of WebGL, but nothing draws in the HTML canvas and me can not see errors in the debug console.

  Any official word on that?  It would bust open a whole bunch of crazy tools if WebGL has been activated.

  On a side note, what is also rendering HTML/javascript engine used in CC?

  TNKS!

  G

  Hello

  You are right. To be precise, we use money chrome embedded framework (CEF) version 1, and later versions will be CEF3.

  V8 powers JavaScript.

  Best regards

  Hallgrimur