the system configuration

Similar Questions

• How can I open the system configuration

  I am running windows xp (version 2002).  How to find the system configuration?

  There is no 'system configuration' in the Panel (at least on my system).

  There is a System option which open to the System Properties screen.

  If mean you the System Configuration utility, click Start, run, and in the type box:

  Msconfig

  Click OK to open the System Configuration utility.

  If you want to see on your current XP configuration information, click Start, run, and in the type box:

  Msinfo32

  Click OK to open the System Information applet.

  It's the same thing you see if you click on start, programs, accessories, System Tools, system information.

• How to remove McAfee security scran more my boot of the System Configuration.

  Hi, my laptop is a Windows vista 32-bit, I have a problem to remove McAfee Security scran more my boot of the System Configuration. In fact, I had used the removal tool to remove the antivirus McAfee sofeware eralier. But when I opened my startup Configuration recently, I noticed that the McAfee security plu scran is still there, I have turn off, but couldn't delete it. Help, please. Thank you.

  Gary

  Hello

  1. are you able to uninstall successful McAfee software?
  2. is there an error message or error code while you uninstall McAfee software?

  Try the following and see if it helps.

  Method 1:

  How to uninstall McAfee Security Scan Plus? : http://service.mcafee.com/FAQDocument.aspx?lc=1033&id=TS100783

  See also: http://promos.mcafee.com/LegacyLp/en-us/affiliates/adobe/landingpages/np681.asp

  Method 2:

  Uninstall if you have any program name McAfee Security Scan Plus on your computer.
  Uninstall or change a program: http://windows.microsoft.com/en-US/windows7/Uninstall-or-change-a-program

  See also:

  Solve problems with programs that cannot be installed or uninstalled:http://support.microsoft.com/mats/Program_Install_and_Uninstall

  Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  Method 3:

  The System Configuration utility displays the items that start with your computer. These items are usually in one of two areas. The registry or during startup.

  If you decide to prevent specific items from start until you can uncheck the in the System Configuration utility. Although this method is very good, it is ultimately preferable to delete them from the source. To access the common locations in the registry of these elements take a look in the following areas:

  Note : open the registry editor by clicking the Start button, type regedit into the search box, and then press ENTER. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

  HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\RunOnce

  Hkey_current_user\\software\\microsoft\\windows\\currentversion\\run

  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Runonce

  If you have disabled items in the System Configuration utility and want to remove the registry also they lies in one of the following locations:

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SharedTools\MSConfig\startupfolder

  HKEY_LOCAL_MACHINE startupreg

  Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

• The System Configuration dialog box; Vista OS: Is it possible to resize the dialog box? If this is not the case, why not plan such an option please?

  Windows Vista; The System Configuration dialog box; dialog resize.

  You can not, this is a dialog box and is not scheduled to be resizable.
   
  --
  ..
  --
  "hyperluckylink" wrote in message
  News: 054b 0592 - 5a9a - 4 c 69-af57-39f8d626f1be...
  > Windows Vista; The System Configuration dialog box; dialog resize.
   
   

• I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information

  I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information. and that did not help. What to do now? The comment of Bios makes me fear that it could damage my computer forever. What should do? Help, please

  Hi Alan,

  Thanks for posting your query in Microsoft Community.

  I understand that the computer does not restart even after running Startup Repair and I will be happy to answer your query. I appreciate the efforts made to try to make it work. Let me ask you;

  • How do you run the Startup Repair?
  • Do you have Windows 7 repair disc?
  • Remember to no particular change in the computer before the show?
  • Have you plugged an external equipment, except the keyboard and mouse?
  • You are able to start the computer in safe mode?
  • What is the brand and model of the computer?

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  There could be several reasons why he's not leaving including hardware as well. In addition, it could be because the master boot record (MBR) has been damaged. When you try to use the Startup Repair tool to repair the MBR, the Startup Repair tool indicates that no problem was found or it does not work yet.

  If you have any connected USB flash drive or other external devices connected to the computer, if you please, remove them and try to run the Startup Repair tool.

  If you haven't tried using Windows 7 repair disc, you can try the following:

  1. Insert the Windows 7 disc
  2. restart your computer
  3. When asked if you want to boot from your DVD player, do it.
  4. Select your language, click Next.
  5. click on repair your computer
  6. Select the operating system you want to repair.

  You can also perform the system restore by selecting the restore point when you think it worked very well. System Restore, choose advanced options using the disc.

  Important: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed after this date are deleted.

  I also recommend to contact the computer manufacturer to get the done diagnostic equipment.

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• How to check the system configuration of the SX20 if the touch screen and the remote control does not work

  Hello friends, would like to know how can we access/check the system configuration of the SX20 if we not touch and remote control or they are not in working condition.

  I think that we can check this Switch interface, but unfortunately, I don't have access to the local switch right now.

  Hello

  option is to have access to the local switch and run "show cdp neighbors detail."

  or

  Connect the mobile to PC/computer LAN, run tftpd32 with affected DHCP pool. Then you can login to get the config.

  regds,

  Aman

• The system configuration does not

  I am running windows 7 and decided to try and resolve messages running and (does not) slow programs. I started to perform a clean boot, but when I had made the changes to the configuration window and clicked on OK the said title bar system (not responding) after waiting a considerable amount of time, I have not quit. When I return to the system configuration window, nothing has changed, but now my PC guard just hung in the system configuration window. The computer is now worse than when I started. I had not done something before.

  The first thing I recommend is to restore and filled to half of the changes that have been made with the System Restore utility. First to save open documents and close all programs and then click Start (or press the Windows key) and type s·ymakeUPS·e·Mr r·emakeUPS·o·r·e then select System Restore programs from the list above. When the system restore starts, click Next and choose the most recent restore point that precedes your attempt to create a boot environment. Follow the rest of the procedure described in this article.

  Restore system files and settings

  Once you have recovered your computer to its state before the attempt to establish a clean boot environment, start with an analysis of malware using a free scan like MalwareBytesanti-malware utility.

  It comes as part of the standard offers free and paid-for versions. For standalone scans and malware removal (but not real time analysis), the free version is usually more than enough.

  MalwareBytes.org

• Change the system configuration and yet no difference in config

  This question is about a router CISCO1941/K9, Version 15.0 (1r) M15.

  When I type

  reload in 4

  He asks me

  The system configuration has changed. Save? [Yes/No]:
  % Please answer 'yes' or «»

  even if

  See the config differences: running system of archives-config nvram:startup

  gives

  ! Contextual Diffs Config:
  ! No changes have been found

  and

  Show running

  gives

  Current configuration: 5031 bytes
  !
  ! No change since the last restart configuration

  My question is: How can I determine WHAT system configuration has been altered?

  As far as I know, the only thing changed is the Terminal length that I occasionally switches for use with the recording of session with PuTTY, which is

  Terminal length 0.

  This router has been in production for months and I don't want to break anything (obviously).  I need to make a change to the configuration of the access-list and wanted to protect me by saying to reload in 4, and then I was probably cancel about 1 minute.  But now I'm worried about it save yes/no question.

  Thank you.

  Hello

  Just save config running and configuration of boot in text files and compare them. Have you enabled all logging on the router?  It may be because of this.

  Just make sure that your configuration register is 0 x 2102. You can see by the show version command

• So that the supply of machinery of vCenter.  Fails on the customization of operating system prompted with the error "windows could not complete the system configuration to try to resume the computer restart configuration.

  Sysprep from Windows fails with the error while the supply of machinery of vCenter. "windows can not finish the system configuration to try to resume the computer restart configuration.

  I use vmware vcenter spec customization here,

  I'd say it's because of incorrect permissions or corrupted registry entry or registry that exceeds 8 KB.

  Please visit https://social.technet.microsoft.com/Forums/windows/en-US/658528ce-6eb5-403b-ae41-458147c2c044/sysprep-failling-after-reboot-into-oobe

  Also change to vmxnet3 NIC and install vmware tools and try cloning.

  "

  ) More than 8 k

  (b) set incorrect permissions

  (c) corrupted somehow

  For me, the problem was intermittent (same registry key would sometimes cause the issue and sometimes not - must be corrupted sometimes) so it was impossible to tell what program it was.  Fortunately, there is a newspaper, you can watch that will tell you exactly what registry key is slightest mistake out.  Here are the steps to get the newspaper, you must see:

  When you see the error message, follow these steps:

  1.) press SHIFT + F10 to get to a command prompt

  2.) stand C:\windows\Panther

  3.) find the Setup.etl file and find a way to copy this file out of the system (I copied it to the partition D:\ and Ghost used to collect this partition and down the file)

  4.) copy the file to another computer that has Windows 7 setup.etl corrupt system.  Place it at the root of C:\ for easier access.

  5.) open a prompt on the Windows 7 computer.

  6.) navigate to the root of C:\ (or anywhere where you saved the file)

  7.) type "tracerpt setup.etl o logfile.csv.

  8.) close command prompt and open logfile.csv in your text editor of choice.

  9.), look in the log file (near the end, probably) for messages that say "Failed to key"reg"process or one of its descendants" to me, the exact eror looked like this: "failed to process the"reg"key or one of its descendants: [profile \REGISTRY\MACHINE\SOFTWARE\ESET\ESET Security\CurrentVersion\Plugins\01000200\Profiles\@My] ' If you search for"«key reg"' or «failed in the process»»» You should find the failure.

  10.) remove this software from your image, or how to get the registry key that does not work properly.

  After that, you should be able to correctly identify any key problem and the elimination/workaround on your image.

  "

• the system configuration not saved during the last stop on the service console error

  Hello

  I m getting this msg of error on the service console

  the system configuration not saved during the last stop on the service console error

  but when I tried to run some commands s troubleshoot mode according to the vmware esxcfg-boot - b, esxcfg-boot - p I got an error message like

  bad interprator usr permission denied

  I guess you follow this KB: http://kb.vmware.com/kb/1002503

  But seems like you have file system errors.

  Try to restart your system in init 1

  Then use fsck command to check your ext3 file system (remember that the file systems are not in use and use the - f option).

  André

• Satellite L500D - always get the system configuration

  Hi, I'm trying to get my new laptop of wifes of configure. It's a L500D.

  I chose 64-bit and all I get now is system configuration. Then it will come in saying we need restart to install the drivers? has been doing this for about 30 minutes now, is there somethig wrong or is this normal?

  It's the 10th time, it has gone and done that.

  Hi Ryan,

  I have the same Satellite L500 which is similar to yours and that of s. The laptop restarts often enough until the installation is complete. That s not unusual, it is necessary to install all drivers and tools you need.

  So I hope you didn t stop or cancel this installation. Just wait a little longer and during this procedure, you can drink coffee and watch TV! ;)

• Features of Installation of Windows 7 software service stops responding when the system configuration

  I noticed that Windows 7 RTM (all versions, x 86 / x 64) has a bug on its features to Software Installation service which causes updates Windows hang during setup of the system (i.e. Windows is stuck on the message "preparing to configure Windows - do not turn off your computer"). M$ suggests to perform a repair with system restore or re - install the operating system from scratch, but is not an effective solution.

  Given that Microsoft has published 5 updates for setup of functionality of software on Vista, I wonder why they don't release a similar patch for Windows 7?

  I opened a support to report the problem incident, which probably occurs after installationreliability KB974431 update(Windows6 1 - KB974431 - x 64.msu).

  When Windows Update installing KB974431 update , the following error message appear when Windows configures updates after the system restarts and the installation of the update fails with error code ofC004F050 .
  Above the error due to the Windows operating system can not pass genuineWindows validation (WGA) . installation of KB974431 will fail if validation fails, or returns a status not valid or not genuine. Here is the procedure to fix it:

  1. click on Start .
  2. in the run box, type cmd and press ENTER.
  3. you will see the black command prompt window.
  4. enter sfc/scannow
  5. If this disable the grace period, it is reset using this code: slmgr /rearm
  6. restart your computer.
  7. try to update again.

  Hope this solution helps!

• My computer takes 9 minutes to start when you turn on. Where can I find the system configuration to abandon some of the start up programs that I don't need.

  I said the reason that my computer takes 9 to 15 minutes to complete the commissioning is there are too many programs that start automatically when I turn it on. They said to click on start and type system configuration and deselect some of the programs to start automatically. I typed in the run dialogue box but nothing.  How do I know where to find it and can you tell me which ones I should NEVER disable? Thank you.

  You type: msconfig in the Run dialog box.

  Under the Startup tab disable this you never or rarely use.

  You will always be able to use them whenever you want without going back to msconfig.

  On the Services tab, click Hide all Microsoft Services, and then choose the ones you want to start when you start your computer.

• during the installation of windows xp, it starts by saying check the system configuration and then will not then stops and won' go further

  IM bought an OEM version of windows xp to install on a computer that I had built, when I finally finished the computer I put the windows disk and booted the system it booted from the disc and said he was checking the configuration of the system, but then it does not go all just stopped. I bought the software from our store of the local computer that is having a closing sale I bought also all the components of the computer, the owner or operator of the store has left the country and Iam left with this problem. the software in its original packaging and with her coa sticker.

  Try this link to find out if youre xp cd is genuine microsoft.                                               http://www.Microsoft.com/en-us/howtotell/default.aspx

  Owner's manual, chk the MB & set the BIOS correctly.

• Change 'Start Up' of the elements in the System Configuration utility

  I tried to remove some the startup items in order to speed up my computer. When I run msconfig and I select "Start" and then check the items to delete, after I selected "Apply" I get a message that basically said... "Access error was returned. You may need to log on as an Adminitrator s changes. As far as I know, I am an administrator as ever, I added all the extra accounts and I always connect under the default account titled original HP administrator.

  In addition, what are the elements are indeed necessary on this menu? Some of them I know but there is a number, I have no idea.

  MSConfig has been designed to be a troubleshooting tool, not a "Start Configurator".  Use MSConfig to determine the location of the command who tries to start the program, and then remove it.  To stop the selective startup notifications, either return your settings to the way they were, or permanently remove unwanted programs from your startup configuration.

  In most cases, with 'good manners' applications, it is usually as simple as opening the unwanted program and deselect the "Show icon in the system tray" option or "launch at Windows startup.

  In addition, look in C:\Documents and Settings\All Users\Menu Menu\Programs\Start Up and C:\Documents and Settings\nom_utilisateur\Menu Menu\Programs\Start files and in the system registry, mainly in the HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Run and HKCU\SOFTWARE\Microsoft\Windows\CurrentVersion\Run key.

  How to troubleshoot using the Msconfig utility in Windows XP
  http://support.Microsoft.com/default.aspx?scid=KB; EN-US; 310560