Themes suddenly stopped working after trying the new theme

Similar Questions

• Capacity wireless suddenly stopped working after an update of Windows Vista.

  Feature WiFi suddenly stopped working after a windows vista updated.  Wireless switch is engaged, but stays yellow that messeges troubleshooting all say computer does not detect wireless devices.  It's as if someone pulled the unit and the antenna of the portable computer.  I also downloaded the wireless drivers and Setup several times without success.  Wireless device appears in the Device Manager page.  The only thing that is showing and work is the cable which is how I can download the drivers and appear on this forum.  Is it possible that the wireless device is broken?  All applicable lights are lit on the networking modem, no signal is detected on the computer, I have concluded that the wireless on the laptop is just inop.  Either way, I have a Compaq Presario F700 laptop.  All the options out there?  Thank you

  original title: can't find the wireless device

  Hello again, Kathy,

  More specific instruction, I can give to check settings in the BIOS of your system is to search for a list of devices that installed your laptop. There are only two options for each device, activate them and deactivate them.
  Look for something listed as network radio or wireless card and make sure that it is set to enable.
  The option that you network adapter found can also control the wireless adapter, but it can control only the plug adapter (Ethernet) network.
  A simpler solution, if you have not already tried it it is the system restore in Windows as mentioned by Kiran in a previous answer:
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore
  WARNING: Changing the BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can resolved e. Changes to settings are at your own risk.

• Speakers stopped working after changing the device sound card

  * Original title: switched to hi-speed of dial-up, speakers stopped working / / rev. #2 Can I change the title of: speakers stopped working after changing the device sound card

  I have a Motorola SM56 speakerphone modem, I went from dial-up to the Road Runner.   When I open Device Manager and expand the sound column it lists "High definition Audio Device" (manufacturer of Microsoft), there are 4 that say "NVIDIA High Definition Audio" then there is one that says "Unimodem Half-Duplex Audio Device.  When I open the properties of the Unimodem device it says ' device working properly. "

  Let me start at the top under "General".  It lists the name of the device: Unimodem half-duplex Audio device.    Device type: audio, video and game controllers;    Manufacturer: Microsoft;    Location: Motorola SM56 Speakerphone modem.

  My speakers worked very well before I went.   I tried updating the driver but he came back with "best driver already installed.  It is a desktop PC, it is about 6 years old, but has been revised, graphics card new, updated to power, new 4 GB ram I think.  The hard drive is 1 TB.   I'm running Windows 7 Pro.  I forgot to mention, if I open a WMV file and volume in the taskbar commands, I see the green light moving.  The green light on the actual speakers turned on, just no sound.  It seems to me that the old speakers do not like the new modem from Time Warner. (I'm an old lady, what the devil I know)

  It is a question of another driver, or is it something else?

  Any help would be greatly appreciated.

  Are plug you the speakers into the modem?

  They must be connected in making your computer speaker, usually a light green color (read the manual of the machine). Go to control panel / sounds / playback and make sure that the type of speakers you selected as the default device.
  Audio device drivers updated its better to not use MS Update (it is not). Re-post giving your machine make name and exact model number (for example HP, Inspiron, ABC1234 etc.).
  See you soon,.
  Jerry

• G72-a20EM screen has stopped working after updating the BIOS F.48.

  How is it possible that BIOS update recommended could turn off the LCD screen.

  Currently I see almost anything on the screen, but vga port works. But increasingly,.

  Intel graphics card is not recognized.

  G72-a20EM screen has stopped working after updating the BIOS F.48.

  What can I do to fix that?

  Good news!

  I found the working version, and it is version F.08.

  Supposedly new version have different Active cables, and this is the reason why the screen is dark.

  So, case closed, everything is perfect.

• Development in error "Installer.exe has stopped working" while installing the new modem.

  Development in error "Installer.exe has stopped working" while installing the new modem. I try to install the ZTE AC8710 modem on my 32-bit windows vista (home edition) system, but whenever the facility is subject to the full I get the error 'Installer.exe has stopped working' and complete Setup doen't. The same error is hit when I try to uninstall the ZTE modem that is installed intestinal. The installation file has CD/install drivers for windows vista. Information below is displayed in the application event viewer for this error log. Help, please

  Log name: Application

  Source: Application error

  Date: 2010-01-03 02:04:50

  Event ID: 1000

  Task category: (100)

  Level: error

  Keywords: Classic

  User: n/a

  Computer: Monica-PC

  Description:

  Application Installer.exe, version 0.0.0.0, time stamp 0x4b208462, Installer.exe module, version 0.0.0.0, time stamp 0x4b208462, exception code 0 x 40000015, offset error 0x0002efec, 0xadc process id, failed failed application start 0x01cab8b5797299e1.

  The event XML:

  1000

  2

  100

  0 x 80000000000000

  309

  Application

  Monica-PC

  Installer.exe

  0.0.0.0

  4b 208462

  Installer.exe

  0.0.0.0

  4b 208462

  40000015

  0002efec

  ADC

  01cab8b5797299e1

  Hi Tonio saini,.

  Navigate to the location of the programs .exe file and right click on the .exe file, and then select run as administrator to install the modem.

  You can also check the following link, try the suggestions and check if that helps:

  http://social.answers.Microsoft.com/forums/en/w7hardware/thread/4ce21286-3a77-4A06-923c-889d657f8e33

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Time protection real HELP in MSE stopped working after running the utility in Windows Live OneCare cleanup tool?

  Protection in real time in MSE stopped working after running the utility in Windows Live OneCare cleanup tool? Error Code: 0x800705b4

  Hello Wally,

  Thanks for posting your query on the Microsoft Community.

  The question error codes and the description that you get suggests that you are facing problem when using MSE. This problem may occur if other security software, such as antivirus, antispyware and antimalware programs, are totally or partially installed on the computer.

  I suggest to change firewall security settings or disable temporary security on the system software and try using MSE and see if it makes a difference. How to temporarily disable security software, you can view the article mentioned below.

   

  Disable the antivirus 

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attack.

  For more details, please see the article mentioned below and see that it helps you to fix the problem.

  Real-time protection lights in Microsoft Security Essentials

  Hope that the information provided is useful. Let us know if you have any concerns related to Windows. We will be more than happy to help you.

  Kind regards

• IR remote stops working after that the system will switch to standby

  IR remote no longer works after that the computer goes to sleep.  I use Windows Media Center (Vista) to the TV and use the remote a lot.  The ONLY way to make it work is to restart the machine, which is a PITA.

  In the device, here is what is displayed Manager...

  Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory. (Code 38)

  I tried uninstalling, reinstalling the driver, unpluging the receiver IR USB, displacement of ports, etc., the software MS difficulty he tried, but nothing works.  It allows to work all the time, but these last few months, you must restart the computer to operate the remote control.

  Any ideas?  Help, please.

  BTW, it is a HP Desktop Media machine, and the remote control is the standard HP remote given out with their machines.

  Here is the official Microsoft fix for error code 38:

  Code 38: Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory
  http://TechNet.Microsoft.com/en-us/library/cc772090%28WS.10%29.aspx

  Have you tried to deactivate "standby" and checked for the repetition of the problem with the IR remote?

  You can ask your question to the Media Center experts at the green button forum:

  http://thegreenbutton.com/

  Have a Word with the help of HP to see if they have a fix for the same.

• Canvio Basic 2 TB suddenly stopped working after Xbox update?

  While to say that the title of the hard drive has stopped working once an update has taken place on the Xbox one a few days ago.

  Now I tried it on a different Xbox one (didn't read), and also tried on a computer laptop windows 10 has yet no chance, at first he tried to install it but only got up then stopped, but even after having passed, still nothing, now its there if I go to device management (depending on whether its fine) but I can not even open the hard drive itself.

  I've had it for about 6 months maybe a little more, but still is it safe, placed just behind the xbox connected, never needed to move it.

  I hope someone can help or suggest something, but im now puzzled.

  Thanks in advance.

  I have the exact same problem mate

• GfxUI.exe has stopped working after rebooting the computer.

  Original title: error GfxUI.exe

  I've been running Vista business for a few years.  Last week, after the reboot, I get an error message that GfxUI.exe has stopped working.  After that I closed the error box, the PC works fine.  I updated the graphic driver Intel, but always the message.  Why now I get the message and how can I solve this problem?

  Hi Kea2300,

  Did you the latest changes on the system?

  This error message indicates to the Intel graphics driver.

  Because you tried to update the Intel graphics card, you can try to perform a clean boot and check if the problem persists.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  After the troubleshooting steps, please refer to clean the boot link to put the computer to normal startup mode.

  Hope this information is useful.

• My Wi - Fi stopped working after trying a LAN line. is any way to fix?

  I have a HP Pavilion dv6265us laptop and I recently tried to use a LAN line with another computer. After this attempt, my Wi - Fi stopped working. He says that I'm connected to any wireless internet access, I chose, but it won't let me connect to any website or any other service online. Anyone know what's happened and how to fix it?

  Hello

  You have a few options in my opinion please try these steps can help you solve your problem.

  (1) unplug the battery adaptor & then press on & press and hold the power button for laptop for 30 seconds then switch on and check if the wireless led lights.

  (2) go to Device Manager then uninstall the drivers wireless network card and restart the device and check if the light is on.

  (3) try to do a system restore to the date where unit was working fine.

  (4) Please update the Bios driver & wireless from the HP website.

  (5) click on start search type Recovery Manager, and then click on it once select Yes on user access control, and then select I need immediate help and then select driver and select request recovery driver wireless and install it and then restart the device.

  (6) If you are comfortable with reinstalling the wireless card that will be on the rear panel of your device you can try this steps as well.

  Please find the link given below could help you too.

  The configuration and the problems of Internet connection on a wireless network with Windows 7

  Troubleshoot an Internet connection loss or E-mail on a network (Windows 7) wireless

• Buttons stop working after pressing the other buttons

  I have three buttons and when I click on the other, the first stops working (for example, no trace event and he traced back to the frame 'tab1'), but the third is still working. Then, when I press the third button the two first and second is no longer working. If I take the stop lines, buttons work fine. The following frames were simply stops on them.

  B1.addEventListener (MouseEvent.MOUSE_UP, b1Pressed);
  B2.addEventListener (MouseEvent.MOUSE_UP, b2Pressed);
  B3.addEventListener (MouseEvent.MOUSE_UP, b3Pressed);

  function b1Pressed(event:MouseEvent) {}
  trace ("hurry b1");
  gotoAndStop ("tab1");
  }

  function b2Pressed(event:MouseEvent) {}
  trace ("hurry b2");
  gotoAndStop ("tab2");
  }

  function b3Pressed(event:MouseEvent) {}
  trace ("hurry b3");
  gotoAndStop ("tab3");
  }

  Is there something obvious that I'm missing?

  Thanks for the ideas.

  Scott

  Check following things:

  1. All three buttons are available on all chassis. [tab1, tab2, tab3]
  2. There is no key between the two images.
  3. If there are key frames are of course you have buttons on the separate layer where there is no frames keys from the beginning to the end.
  4. If you have to have keyframes for the buttons then assign the event listener once more on each keyframe. [as when you insert a keyframe, gets a new bifurcation place]

• HP Pavilion G7: Laptop suddenly stopped working after applying an update

  So I was watching netflix and I got the warning that I had five minutes to shut down the computer or it would be closed himself so that he could catch up. I had done the things in closing and stop it by pressing the power button and in now supported.  Then, I turned on the computer laptop back and he started to update so I zoned out of it and watched something on my phone. While doing so I noticed some type of error message update and do not touch, it's because the last time it happened that just rebooted without the update. However instead he himself off and does not turn around. I tried to hit the buitton of power to reactivate and that did not work. I also tried the suggestions I found on this website to support such as take out the battery and unplug the power adapter to the power source.

  Hi @Spinto46,

  Thank you for the update.

  You have determined that the adapter works, it could be in the laptop power button.  The laptop will require a repair.  Please contact HP support for service options. They provide you with an estimate before performing any repairs.

  Contact HP to Contact HP Support assistance

  If you are not under warranty, a local repair shop should be able to provide an estimate also.

  If you want to consider replacing it yourself to see what is the matter, here's a link to the:

  HP Pavilion Notebook PC Maintenance and Service Guide of g7

  Please note Chapter 4, page 52 for replacement part number and removal and replacement instructions.

  For your convenience, here is a link to the:

  HP parts store

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  Also, by clicking on the ""Thumbs Up ' below is a great way to say thank you! "

• Re: Wireless suddenly stops working after traveling abroad

  Toshiba Satellite L402, WXP

  Before you travel my laptop wireless works perfectly, after traveling abroad, I tried to connect to my network wireless at home, but I can't see any wireless network.

  I have two computers at home, PC and laptop, the PC has no any problem connecting to the wireless and can see all available wireless network, while my laptop has his red X mark on its icon on the quick launch wireless and can not display any network without wire around, I have re installed the driver but still it won't work , I tried to connect my psp and portable to my wireless router just to check if the connection to the router is limited, but I was able to connect to it.

  Any idea on what I need to check or do? Thank you!

  Hi guel27,

  -have you checked if the wlan switch is in the correct position?
  -If the position is ok, check the hardware by using Device Manager. No red or yellow cross on the wlan adapter? Okay, you guys:
  -check if the network connection is not disabled in the overview of network connections
  -(droite-klick sur réseau/wlan-icon dans la systemtray et vérifiez votre connexion si elle est désactivée.)
  seing any Red Cross on your wlan conn? Okay, you guys:
  -Perhaps you have installed a wireless Internet favorite, at least you could:
  -delete all favorite connections and choose dhcp instead of a static ip address

  BTW: Be sure to use the driver for your nic corect!

• LifeCam has suddenly stopped working after many years

  Original title: problem with my Microsoft Lifecam VX-6000

  Problem with my Microsoft LifeCam VX-6000.  I used my LifeCam several times when using Skype, but now it will not work.  I examined a large number of questions and answers that are listed in the support forum but nothing I found fixes my problem.  I am running Vista Home Premium on my HP #SR5050NX PC with a 32-bit operating system.  I used this webcam for many years without any problems, but now it will not work.  I reinstalled the current drivers on the Microsoft site and it appears in Device Manager that the drivers are correct for the LifeCam VX-6000 webcam.  When I try to open Microsoft LifeCam it locates my camera and the green light comes on but no picture.  When using Skype, he finds the camera LifeCam 6000 but gives me a message that it cannot use this device because it might already be in use by another application, but no other application works.  I have also a Cisco Webcam that I have in the past to select which camera I wanted to use while Skyping but he stopped working at the same time my LifeCam 6000 ceased.  I get the same message... This webcam cannot be used because it might already be in use.  The drivers are correct on this camera as well.  What can I do to fix this?

  Thanks, I appreciate your help and your support!

  datgrt

  Hello

  I suggest you to return these items and check if it helps:

  Troubleshoot failures to find the new LifeCam hardware

  http://support.Microsoft.com/kb/929087

  Don't troubleshoot bad or no video or problems to start the LifeCam software

  http://support.Microsoft.com/kb/933310

• Windows live mail stops working after closing the program

  Although Windows Live Mail sems to work properly, every time I close the program, I get a dialog box indicating that the program has stopped working and windows will notify me when the solution becomes known.  After searchign this topic I cam in all of the discussion in

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_programs/Windows-Mail-has-stopped-workinga-problem-caused/e4babe31-c0db-4fe5-b92e-cd1d17e4bc04

  And I started Widnows in a boot minimum - and still encountered the problem.  I am running Vista Home Premium SP2 with Live Mail 2011; My Anti Virus is Norton.  Thanks for any help.

  Please publish on Windows Live Solution Center.

  Here is the link to the e-mail discussion forum:
  http://windowslivehelp.com/forums.aspx?ProductID=15