Then the display turns off I can't get it back without force restart

Similar Questions

• Satellite M300 display lights then the backlight turns off

  I have a M300 Satellite.
  When I turn on my computer the screen comes on then the backlight turns off.
  Display on an external monitor.
  I have tried funtion buttons, move the screen has no effect.

  Any ideas?

  Hello

  Are you able to increase the backlight using Fn + F7?
  Have you checked the power management option that controls the backlight for the different consumption patterns?
  Will you please do because the power management could lower the backlight to save battery.

  If changing the settings of theses will not help, so I guess FL inverter small failures that may cause this problem.
  In this case that the parts must be replaced

• Help: Fuze distorts the sound when the display turns off

  Hello

  Since a few days, I own my rocket. Today, I recognized the following problem:

  When the display turns off the "rocket" distorts the song. It's a bit like stuttering, it's his bad.

  When I keep the screen turned on (by clicking on the boxes or more) he playes the song of good quality.

  The EQ is set to standard.

  Has anyone experienced the same problem?

  I don't know what to do, what an individual problem of my camera (default?) or maybe a general problem? I would stay there or should I change it?

  Thanks in advance,

  Stefan

  This problem is fixed in the next firmware should be out in the next few days.

  TO work around it, just put the equalizer settings on the equalizer custom for anything other than 0,0,0,0,0

• the button to add an image to a collection on my image went in the library module. How can I get that back?

  the button to add an image to a collection on my image went in the library module. How can I get that back?

  Press [J] to toggle the info of the image, then the gray appears on the preview image.

  

• Where the health dashboard? How can I get it back?

  Where the health dashboard? How can I get it back?

  Press the tile of the activity.

  

  All sections of the dashboard are there now.

• I have an iPhone running on iOS 9.2 6s sound shutter for the camera disappeared. How can I get that back?

  I have an iPhone running on iOS 9.2 6s sound shutter for the camera disappeared. How can I get that back?

  Check if the phone has got accidentally switched on for mute. -AJ

• lost my card character, not in the system 32 folder, how can I get that back?

  lost my card character, not in the system 32 folder, how can I get that back?

  lost my card character, not in the system 32 folder, how can I get that back?

  It's a pretty good trick, considering that charmap.exe is one of the files that Windows File Protection is supposed to protect.

  Do a full disc search for charmap (without extension), making sure to look into the hidden files and system.

  If charmap.exe is not in C:\Windows\system32 (where it belongs), he probably is not in C:\Windows\system32\dllcache (where it also belongs).

  If you have a directory (which is common for systems with Windows) C:\i386 pre-installed, you should find charmap.ex_, which is a compressed version of the file.  You must use the EXPAND command from a command prompt window (start > run > cmd > OK) to decompress:

  Expand c:\i386\charmap.ex_ c:\windows\system32\charmap.exe
  copy c:\windows\system32\charmap.exe c:\windows\system32\dllcache

  Don't forget the space before the c:\ at two locations in two lines

  You will also find the charmap help files in C:\i386 and can expand those as well if necessary.  The expanded files should reside in C:\windows\help

• Can not turn on the monitor on the Satellite once the display turns off after 10 min

  Hello..

  I have a problem with my laptop...

  When the screen turns off after 10 minutes, it no longer lights!

  I move the mouse, try typing on the keyboard, but it does not work...

  to activate the display again once I should close the lid for the hibernation, then open it again!

  I hope that you will help me @_ @!

  Hello

  Check it please http://support.microsoft.com/kb/917332/en-us
  To correct the behavior please download and apply the patch (KB917332) which could be found in the resolution detailed below. I hope this will help.

• The display turns off after a few minutes and shows 'No Signal'

  Hey guys, I was faced with a weird problem recently. My desktop monitor turns off by itself after a few minutes, but the works of CPU, I can hear the fan running and see the lights blink. One thing I noticed, is that when the screen turns off, the light Orange on the processor rest on which flashes normally just. My PC works normally on the mode without failure, but worse, safe mode, but I can't work on my software CorelDRAW. This may be the problem of SMPS? because recently, my entries of mouse and keyboard did not work due to which I got a USB keyboard and a mouse. I recently installed Windows 7 64 bit, but I think that shouldn't cause the problem since I have worked with Windows 64-bit before on the same machine.

  PC configuration-

  Intel Core 2 Duo 4500 @ 2.20 Ghz processor
  ASUS P5QPL-AM motherboard
  3 GB RAM
  No (not sure, maybe integrated) graphics card
  1 TB harddrive

  PS - I couldn't find an exact category for my problem.

  Hey Archer
  Currently, I formatted my Windows 7 and installed Windows 8 and am these problems persist. I have not upgraded but formatted my C drive and installed a fresh new copy of windows 8... so I thnk it may be a problem of the SMP. Can he?

  Hi sunny

  It can or mentioned being SMPS... the reason is... you have already said that the computer or the monitor works fine in safe mode! But since his past even when you install Windows 8,
  To make troubleshooting a
  1. go to the Bios and reset all default by selecting the optimum setting in the bios... Given that your motherboard has got characteristic overclocking and selection of the IGD... let him get by default...  Start the computer and check if the monitor turns off always.
  2. If step 1 does not solve your problem... then go to the power option in the control panel and select your power setting of the high-performance system where you can set your monitor to never go to sleep.  See what's happening... If the monitor still going to sleep even after this setting... then you have a problem with drivers or the motherboard... try updating the drivers and see if that helps.
  3. If the update of drivers did not help... so the next option is to review your material... try to get a replacement screen and see if this could solve this problem... A things you can deduct that if this also fails, then the obvious reason is that your monitor is ok... and problem must be the motherboard.
  4. Firstly check the display port... does it feel loose?
  a. do you have this port pins come out?
  b. your motherboard has two power connections (EATXPWR 24-pin and a 4-pin ATX 12V... are both connected?
  c. your SMP should be at least 400W according to recommendations from the manufacturer to you. Check this box...
  d. then ofcourcse obviously... Reinstall the Rams and other external devices.
  Follow these steps and let me know your comments for each

• PC starts, I set password and then the screen turns off and goes no further

  Hi, I start my g6 pavilion 2240, I get as far as putting my password then the screen turns white and I get not further

  don't know what to do now, I'm a surfer of money, so please tell me answers I can understand. Thank you very much

  Hello

  Try to use the system restore Windows to return the machine to an earlier point in time when it worked correctly - a complete guide on how to make of this (including a video preview) can be found on the link under the subheading: restore your computer when Windows 8 cannot start normally (it's to halfway down the page).

  http://support.HP.com/us-en/document/c03327545

  Kind regards

  DP - K

• I lost all my content on the Adobe voice. How can I get that back?

  I lost all my content off my creative cloud. How can I get that back?

  I have been using Adobe voice for a few months now for work, yesterday, I disconnected my voice of adobe and update of the application itself, then after updating the app, I logged in and it only showed that I have 2 projects on it. (I think I got somewhere about 15 projects) I tried logging on several occasions and then he lost all my projects for a day. Now, there are just 20 minutes I logged again and is again show these 2 videos. I don't know what's going on, or why this happened. But I could really use these 15 projects/videos or if as I use this app for my work. Thank you very much.

  Hello

  Can be found here: https://standout.adobe.com/support/#voice

  -Dave

• I deleted the camera icon. How can I get that back?

  I've removed the camera icon, how can I get it back?

  Hello

  has been the home screen icon?

  If this is the case, you can press applications and widgets on the upper right, then look for the camera icon, then press and hold the icon to place it anywhere on your home screen.

• Icon for the DESKTOP disappeared. How can I get that back?

  I have somehow deleted the icon for my taskbar background OFFICE.  How can I get that back?

  Hello

  What operating system is installed on your computer?

  To display the icon on the desktop, visit the link below:

  For Vista: Show, hide, or resize desktop icons

  http://Windows.Microsoft.com/en-us/Windows-Vista/show-hide-or-resize-desktop-icons

  For Windows 7: Show, hide, or resize desktop icons

  http://Windows.Microsoft.com/en-us/Windows7/show-hide-or-resize-desktop-icons

  For Windows XP: Your desktop icons are missing in Windows XP

  http://support.Microsoft.com/kb/330170

• The line to type under the tabs disappeared. How can I get that back?

  The line under the tabs - where I could type in a question, view the address of the web site or web site is missing. How can I get that back?

  Hi WriteGirl,

  You can click View > toolbars > and check "Bar of Navigation" to get this back bar.

• on the painting, I lost the Cancel button and I can't get it back

  I accidentally pressed a button o please email but him undo the button disappeared and im trying to get it back.

  If you open a new paint document, immediately to the left of the words 'Untitled - paint' at the top of the window, there is a small arrow with a horizontal line above him down.  Click on that and then click Cancel in the list that appears and your cancel button should be back.