Thermotron TCP/IP interface

Similar Questions

• How do I get the data in a table column of material using the tcp/ip interface

  Hello everyone, I want to get my material data using tcp /ip interface.and and then display them in a column of the table control? can any body tell how to do that .that me clear I never before communicate with hardware so please help me in detail.

  Thank you

  Hi Charlotte,.

  ask that 'someone' for more specific information.

  You must know the exact format of the channels you receive in order to analyze!

• using tcp replacement reset interface

  Hi I'm new to cisco ips. can someone tell me pls the function to use the alternative interface for tcp reset.

  I have 2 interfaces for IP addresses. a command and control and other interface is an interface in promiscious mode.

  without this command the ID can send some tcp resets. or because it uses a different interface for tcp resets.

  can someone tell me pls.

  concerning

  Assane

  Under most of the facilities the tcp replacement reset interface is not necessary.

  By default the ports TCP resets will come back on the same interface where the attack was detected.

  So if your interface promiscuity is connected to a 100 Mbps for tracking hub then the tcp reset will be sent back this same interface promiscuitee in the hub.

  Or if your interface promiscuity is connected to the span switch port, the tcp reset will be sent back the same interface of promiscuity in that span port.

  The question becomes is the sensor can send reset tcp, but if the switch will accept them. Various switches will accept from the span port tcp resets. Some switches require only an extra parameter on the extended configuration to tell the switch to allow incoming packets to the span port.

  BUT there are some switches that do NOT allow incoming packets of their span ports.

  These ituations are the reason for the replacement tcp reset the configuration of the interface.

  Need 2 remote sensing interfaces (one for surveillance of promiscuity and the used the other as just replacing tcp reset interface). The port command and control NOT allow as the other tcp reset interface.

  Connect to the interface promiscuity to the scope of the switch port. You configure the second interface as the alternate tcp reset interface of the first interface of promiscuity. Then plug the second interface on the switch of the saem (but do not have the 2nd one a span port).

  Now, when the sensor detects an attack on interface 1 it will NOT send tcp resets the interface 1, but rather will send the reset tcp on the 2nd interface.

  Given that the switch does not accept that the tcp resets since the span port you need of the second interface for tcp resets in the switch.

  It is also possible with taps where the taps (because the taps have no way to accept incoming packets).

  The alternative tcp reset interface configuration is ignored when it is configured for online tracking. It is used only with supervision of promiscuity.

• TCP Reset and blocking

  I'm IPS-4270-20 configuration.

  I want to know how TCP Reset would reset a session without having an IP address.

  Then what interface would BOW orders blocking and rate limiting actions on managed devices.

  Kind regards

  Shahzad.

  Your switchports will be set to 'access' If you use the 'pair of inline physical interface' mode and it will be a trunk when you use "pair mode for vlan inline.

  And here's a post from Marc regarding the alternative tcp, its rarely need reset to:

  "Under most of the facilities the tcp reset interface replacement is not necessary.

  By default the ports TCP resets will come back on the same interface where the attack was detected.

  So if your interface promiscuity is connected to a 100 Mbps for tracking hub then the tcp reset will be sent back this same interface promiscuitee in the hub.

  Or if your interface promiscuity is connected to the span switch port, the tcp reset will be sent back the same interface of promiscuity in that span port.

  The question becomes is the sensor can send reset tcp, but if the switch will accept them. Various switches will accept from the span port tcp resets. Some switches require only an extra parameter on the extended configuration to tell the switch to allow incoming packets to the span port.

  BUT there are some switches that do NOT allow incoming packets of their span ports.

  These ituations are the reason for the replacement tcp reset the configuration of the interface.

  Need 2 remote sensing interfaces (one for surveillance of promiscuity and the used the other as just replacing tcp reset interface). The port command and control NOT allow as the other tcp reset interface.

  Connect to the interface promiscuity to the scope of the switch port. You configure the second interface as the alternate tcp reset interface of the first interface of promiscuity. Then plug the second interface on the switch of the saem (but do not have the 2nd one a span port).

  Now, when the sensor detects an attack on interface 1 it will NOT send tcp resets the interface 1, but rather will send the reset tcp on the 2nd interface.

  Given that the switch does not accept that the tcp resets since the span port you need of the second interface for tcp resets in the switch.

  It is also possible with taps where the taps (because the taps have no way to accept incoming packets).

  The alternative tcp reset interface configuration is ignored when it is configured for online tracking. It is used only with supervision of promiscuity. "

  Concerning

  Farrukh

• Routing and remote access - on three subnetworked, two subnet unable to reach to the internet!

  Hello

  Good evening everyone.

  I had a problem in Routing and remote access on windows 2003 server.  This server is already configured as a file server, domain server, and application server. Also configured as a router (thanks to access routing & remote) to connect the three different networks with each other. If this server has three NICs installed and each separate NIC network cards represent.

  three different networks are - 192.42.160.0/24, 192.42.161.0/24, 192.42.162.0/24

  Three cards of the NETWORK adapter installed on the server as with the IP - next

  NIC - 1 = 192.42.160.220, Sub - 255.255.255.0, gateway - No.

  NIC - 2 = 192.42.161.220, Sub - 255.255.255.0, gateway - 192.161.220.112 (this ip address for internet access then 4 g router IP)

  -3 = 192.42.162.220, NETWORK cards, Sub - 255.255.255.0, gateway - No.

  Now the question is I can get Internet & (also scathing in router ip 192.42.161.112) one network i.e. - 192.42.161.0/24, BUT when I try to access the internet from another two network (192.42.160.0/24 & 192.42.162.0/24) I can not access and in addition can not ping to internet router ip - 192.42.161.112...

  So, how do I access the internet to another two network also?

  I was already the configuration of static routing for all three network but I wasn't always successful. I don't really know what exactly static routing this should be done in access routing & remote area so that all three network can reach to the internet?

  Here is the result of the current track...

  D:\Documents and Settings\Administrateur > route print

  IPv4 routing table
  ===========================================================================
  List of the interface
  0x1 ........................... MS TCP Loopback interface
  0x2... 00 30 05 8f ad 5 c... Broadcom NetXtreme Gigabit Ethernet - Mi Teefer2
  niport
  0 x 3... 0E 00 c4 f8 a7 0c... Network Intel(r) PRO/1000 GT Desktop Adapter - Teefer2 M
  iniport
  0 x 4... 0E 00 0c a7 c5 85... Intel (r) PRO/1000 GT Desktop Adapter #2 - Teefer
  2 miniport
  ===========================================================================
  ===========================================================================
  Active routes:
  Network Destination gateway metric Interface subnet mask
  0.0.0.0 0.0.0.0 192.42.161.112 192.42.161.220 1
  127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
  192.42.160.0 255.255.255.0 192.42.160.220 192.42.160.220 20
  192.42.160.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.160.255 255.255.255.255 192.42.160.220 192.42.160.220 20
  192.42.161.0 255.255.255.0 192.42.161.220 192.42.161.220 20
  192.42.161.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.161.255 255.255.255.255 192.42.161.220 192.42.161.220 20
  192.42.162.0 255.255.255.0 192.42.162.220 192.42.162.220 20
  192.42.162.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.162.255 255.255.255.255 192.42.162.220 192.42.162.220 20
  224.0.0.0 240.0.0.0 192.42.160.220 192.42.160.220 20
  224.0.0.0 240.0.0.0 192.42.161.220 192.42.161.220 20
  224.0.0.0 240.0.0.0 192.42.162.220 192.42.162.220 20
  255.255.255.255 255.255.255.255 192.42.160.220 192.42.160.220 1
  255.255.255.255 255.255.255.255 192.42.161.220 192.42.161.220 1
  255.255.255.255 255.255.255.255 192.42.162.220 192.42.162.220 1
  Default gateway: 192.42.161.112
  ===========================================================================
  Persistent routes:
  None

  Sorry if I'm not able to explain properly. Please let me know if you have to explain more about it...

  Thank you all.

  Mahesh

  Hello Manu,

  Please post this question in the forums TechNet for Windows Server 2003. They will be able to guide you further.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

• GPIB on general issues RT PXI

  Hello!

  First of all, I am a real beginner in the 'world of LV in real-time. I'm at the beginning of a new project where a part of the system consists of a PXI with RT OS system, including a GPIB interface. This interface must be connected to several meters of picoamp Keithley (model 6485 & 6487). The RT code should read data from Keithley devices and also run certain commands on devices (like zero of them, turn the high voltage, etc..). The other part of the application of the RT PXI will have a TCP/IP connection to a Siemens S7 system and send data more receive incoming orders to be executed on the Keithleys. Anyway, Siemens via TCP/IP interfacing is another great challenge and could be a topic for another future post. Now, I want to just treat the GPIB part...

  I would ask people familiar with PXI RT (and possibly GPIB on these platforms) for best practice & advice:

  1. I had the official driver of Textronix for LabVIEW ( http://www.tek.com/specialty-instruments/6485-software/models-6485-6487-and-6514-ivi-visa-based-driv... ), but the pilot works via a DLL. I think that this is not a good idea (is it even possible?) to use a DLL on a RT operating system and adds more complexity (there will be a lot of PXI systems later). Therefore we should implement our own driver using basic VISA, am I right?
  2. I would like to have a robust system of RT, so it should automatically detect all Keithley devices connected, and also model check type (only model 6487 a voltage supply option). I guess that if VISA Runtime is installed on the RT operating system, so I can also use the 'VISA find Resource.vi' for a list of available devices GPIB? I'll also have to program a function to handle the scenario when a crimp module is disabled or removed from the string, so the RT operating system it goes not down, but it shouldn't be a problem...

  All advice and suggestions are welcome.

  Thank you!

  1 dll are compibled for Windows.  So that won't work on RT, Pharlap, VxWorks or RT Linux operating system.  You will need to do your own driver using VISA calls.

  2 since you have to manage different Keithley instruments, I highly recommend to go with an OBJECT-oriented approach.  Most of the similar instruments should have the same commands, so I doubt that you will have a deep hierarchy.

  Now, my advice is to do all of your creation of pilot and testing on a Windows machine.  All of the code that your development should work just find when you take for a RT system.  This is the command structure that counts more than anything.

• Inexplicable FPS problem on Acer V3 772 G

  Hello! I use Acer V3 772 G with Intel Core i7, GTX 760 M, 8 GB of RAM, running on Windows 8.1, if it's important. I've been making FPS problems lately. I lived at random the sudden drops of FPS (down like 15) in all games regardless of the settings. What I did when it happened - I reinstalled the drivers from the computer, cleaned up a bit (virus, records, etc.), restarted and the FPS was back to normal. I just want to mention what exactly two weeks ago, I made a new clean install on Windows, this is why I do not have to put it back. However, yesterday I discovered something very special:

  -Laptop is plugged in and everything goes perfectly well - I play at a constant 40 fps.

  -J' I unplug the laptop and the FPS suddenly starts between 15 and 30 frames per second through drops very sudden and uncomfortable.

  -I plug the lapotp once again and it's going better... just not pretty. ALMOST, it hangs at about 33-5 fps with (just not as frequent as before is) drops to about 25. I change the settings as low as possible and it keeps passing 25 anything.

  -I restart the laptop and all of a sudden, it is good.

  Except that restart today does not help. Any suggestions for what could possibly cause that ideas and how to fix it? Thanks in advance!

  A few side notes:

  -J' put 'High Performance' of the computer in the control panel NVIDIA and Windows Power Management.

  -J' set the preferred graphics processor be NVIDIA processor high performance in global settings in the NVIDIA Control Panel is not likely to be a problem of the IGP.

  -The temperature of the CPU and GPU are both at about 50-60 ° C when the phone is idle on dekstop with no process on. Is it too high or something?

  -J' I disabled some services Intel and NVIDIA in msconfig. I think the problem dates well before that, but I'll mention that I disabled even when:

  Intel HECI service content protection

  Intel capacity Licensing Service Interface

  Ability of Intel Licensing Service TCP IP Interface

  Service to host dynamic Intel Application Loader Interface

  Intel management and security of Application local management Service

  Update NVIDIA services daemon

  AetherosSvc (this is something Windows but anyway...)

  Reading about your post, I'm noting several things that could affect your system.  You you deleted man of State, under the direction of the registry and do a clean install of Windows on the system.

  I will suggest that restore you the system to the factory load and try again.

  Acer will not be able to suport a copy of the operating system that you are installing the retail.

  Please see this link:
  Installation of a different operating system

  Recharge your Acer computer

• L2TP - impossible to find a group valid tunnel

  Hello

  I'm sure this is a simple solution, but I don't see what I'm missing.

  Any help please?

  Get the following errors in debugging.

  [IKEv1]: invalid tunnel, leaving group = 95.83.254.91, IP = 95.x.x.x, impossible to find a group...!
  23 September 14:26:05 [IKEv1]: IP = 95.x.x.x, invalid header, lack of payload SA! (next payload = 4)

  Group of tunnel I want to use is Remote-L2TP

  Attached config.

  ASA Version 8.2 (5)
  !
  ciscoasa hostname
  domain xxxxx.local
  activate 8Ry2YjIyt7RRXU24 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  name 192.168.1.40 description CCTV system CCTV_System
  name x.x.x.x outside outside interface description
  description of the SERVER name server 192.168.1.1
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  switchport access vlan 12
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  192.168.1.222 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address outside 255.255.255.252
  !
  passive FTP mode
  clock timezone GMT/IST 0
  summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  Server name 89.191.34.249
  domain xxxxx.local
  object-group service CCTV tcp
  port-object eq 9010
  object-group service CCTV_NEW tcp - udp
  port-object eq 9091
  object-group service BlackBerry tcp - udp
  port-object eq 3101
  object-group service NSM tcp - udp
  port-object eq 886
  object-group service RDP tcp - udp
  EQ port 3389 object
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  outside_access_in list extended access allowed object-group TCPUDP any host outside eq 9091
  outside_access_in list extended access allowed object-group TCPUDP any host outside eq 886
  outside_access_in list extended access allowed object-group TCPUDP any host outside eq 3101
  outside_access_in list extended access permit tcp any host outside eq https
  outside_access_in list extended access permit tcp any interface outside eq pptp
  outside_access_in list extended access allowed esp any external interface
  outside_access_in list extended access permit udp any interface outside isakmp eq
  outside_access_in list extended access permit udp any interface outside eq 4500
  outside_access_in list extended access permit udp any interface outside eq 1701
  standard access list for distance-VPN-Gp_splitTunnelAcl permit 192.168.1.0 255.255.255.0
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.25.0 255.255.255.192
  RemoteVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  VPN-GP_splitTunnelAcl-list of allowed access standard 192.168.1.0 255.255.255.0
  standard L2TP_splitTunnelAcl-Remote Access-list allowed 192.168.1.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  mask of local pool Remote-DHCP-POOL 192.168.25.10 - 192.168.25.50 IP 255.255.255.0
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  public static 9091 9091 CCTV_System netmask 255.255.255.255 interface tcp (indoor, outdoor)
  public static 886 886 SERVER netmask 255.255.255.255 interface tcp (indoor, outdoor)
  public static 3101 3101 SERVER netmask 255.255.255.255 interface tcp (indoor, outdoor)
  public static tcp (indoor, outdoor) interface https SERVER https netmask 255.255.255.255
  public static tcp (indoor, outdoor) pptp pptp netmask 255.255.255.255 SERVER interface
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 89.191.53.17 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication http LOCAL console
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac trans
  Crypto ipsec transform-set trans transport mode
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  Crypto-map Dynamics dyno 20 transform-set trans
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  card crypto 20-isakmp ipsec vpn Dynamics dyno
  vpn outside crypto map interface
  Crypto ca trustpoint _SmartCallHome_ServerCA
  Configure CRL
  Crypto ca trustpoint ASDM_TrustPoint0
  registration auto
  name of the object CN = ciscoasa
  Configure CRL
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  string encryption ca ASDM_TrustPoint0 certificates
  certificate 5eb57b56
  3082016a 30820201 a0030201 0202045e b57b5630 0d06092a 864886f7 0d 010105
  3111300f 05003045 06035504 03130863 6973636f 61736131 30302e06 092 has 8648
  09021621 63697363 6f617361 2e627574 6 c 657274 6563686e 6f6c6f67 86f70d01
  6965732e 6c6f6361 6c301e17 313630 39313931 33303732 395a170d 32363039 0d
  a 31373133 30373239 5 304531 11300f06 03550403 13086369 73636f61 73613130
  2a 864886 f70d0109 6973636f 02162163 6173612e 6275746c 65727465 302e0609
  63686e6f 6c6f6769 65732e6c 6f63616c 30819f30 0d06092a 864886f7 0d 010101
  8 D 003081 89028181 05000381 008e76a6 2ad8e079 15814471 df2c3309 abdc0ae7
  1c665f5f bb09154b 1ac3fd81 930b29cb 6da29338 738c 9373 a0b30f61 a1d08aa9
  f5ef926b 11ef1e22 e8beeb5f c6606090 7a71b367 cad571c5 56331678 d83d4bb4
  9f98a565 577cccd6 dc20e190 c7128cf2 e38d3ad1 37807440 3da501c2 14bbbe02
  45abf677 89248633 d 05589d 4886f70d 01010505 55 75020301 0001300 06092a 86
  000a7b9d 00038181 3e29b1d9 8459309b 5e24606a cae0710e b9e264f4 a61125b9
  2f431f3a 5c4a9485 fe9bc0b0 9f9f7072 13abd978 243e0542 e34642d6 ae33028d
  be03b9e9 56c693ab b082932d b44ab014 9366c0d4 529a7ff5 818f7293 2026521b
  52fcf5c7 d623f7fa 54019c 86 e64a4212 08444c 58 8ccd11d8 4297d18a c4b2de33
  2003eaf5 e2
  quit smoking
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH 192.168.1.0 255.255.255.0 inside
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 30
  SSH version 2
  Console timeout 0
  dhcpd outside auto_config
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  NTP 79.125.112.210 Server
  NTP server 193.1.193.157 prefer external source
  WebVPN
  port 8443
  allow outside
  DTLS port 8443
  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
  SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image
  Picture disk0:/sslclient-win-1.1.4.176.pkg 3 SVC
  enable SVC
  attributes of Group Policy DfltGrpPolicy
  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
  WebVPN
  SVC request enable
  internal RemoteVPN group strategy
  attributes of Group Policy RemoteVPN
  value of server DNS 192.168.1.1 192.168.1.2
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list RemoteVPN_splitTunnelAcl
  XXXX.local value by default-field
  internal strategy group at distance-VPN-GP
  remote control-VPN-GP group policy attributes
  value of 192.168.1.1 DNS server
  Protocol-tunnel-VPN IPSec
  XXXXX.local value by default-field
  internal strategy group to distance-L2TP
  L2TP remote group policy attributes
  value of server DNS 192.168.1.1 192.168.1.2
  VPN-tunnel-Protocol webvpn
  username privilege 15 encrypted v5FJjvsPy8PsIOtZ xxxxpassword
  attributes of username xxxx
  VPN-group-policy RemoteVPN
  xxxxx YeC9t79Bj2E5FxxV username encrypted password
  attributes of username xxxxx
  Strategy-Group-VPN Remote - L2TP
  2KXeP2Ggcoa6BTsozucgAA password xxxxx user name is nt encrypted
  remote access of type tunnel-group to distance-VPN-GP
  distance-VPN-GP-global attributes tunnel-group
  Remote control-DHCP-POOL-pool of addresses
  Group Policy - by default-remote control-VPN-GP
  tunnel-group GP-remote control-VPN ipsec-attributes
  pre-shared key *.
  type tunnel-group Remote-L2TP remote access
  attributes global-tunnel-group Remote-L2TP
  Remote control-DHCP-POOL-pool of addresses
  Group Policy - by default-remote-L2TP
  tunnel-group Remote-L2TP ipsec-attributes
  pre-shared key *.
  tunnel-group Remote-L2TP ppp-attributes
  ms-chap-v2 authentication
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the pptp
  !
  global service-policy global_policy
  context of prompt hostname
  anonymous reporting remote call
  Cryptochecksum:c4b7c39420a91e2f7bb4adc5e5a8539b
  : end
  ciscoasa (config) #.

  Hello

  I see same Phase 2 is completed in the newspapers, so more than a customer issue.

  On the Security tab in the connection on the client profile, check if you have allowed the correct password and security protocols:

  https://www.SoftEther.org/4-docs/2-HOWTO/9.L2TPIPsec_Setup_Guide_for_Sof...

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• From single to multiple IP addresses external IP traffic internal

  We are transitioning to a Symantec SMS to a Cisco ASA 5505, and I'm running into a lot of trouble to replicate our configuration for inbound traffic. We currently have a Setup something like this:

  (Of course I pick up a bunch of arbitrary numbers here.)

  1.2.3.4 port one--> 10.1.0.1 port one

  1.2.3.4 port b--> 10.1.0.5 port b

  1.2.3.4 port x--> 10.1.0.20 port p

  1.2.3.4 port is--> 10.1.0.21 p port

  1.2.3.4 port z--> 10.1.0.22 p port

  1.2.3.4 is the unique external IP address we use for traffic that passes through, and 10.1.0.x internal host. x, y and z are ports chosen arbitrarily in a sequence.

  I'm doing it via the ASDM. The ASA is running 9.1 2 software and I use ASDM 7.1 (3). I'm trying to accomplish this by using Configuration > firewall > public servers.

  What I do is the following:

  1. In Configuration > firewall > objects > network objects/groups, create objects for the external IP address and all internal hosts.
  2. In Configuration > firewall > objects > objects/Service groups, create objects TCP ports x y z, and a TCP object for p port (which is not in the default set). Protocols on ports a and b are in the game by default, so they do not need to be defined.
  3. In Configuration > firewall > public servers, add a series of entries of public server with the external host as public IP, address the external interface as the public Interface, the internal as the private Interface interface, the host in question as IP address private, and in the case the two first entries, the protocol chosen as the private service sector. In the case of the last of three entries, I also selects "public address specify if it is different from the private Service. This will allow the static PAT. "I then selects the associated service from port p as the private Service and the service associated with the ports x, y or z (respectively) in the public service.

  .. .or at least, that's what I'm trying to do. I have encountered the following problems:

  1. If I do not use 'Specify the public address if different of the private service', the first mapping I do works very well and pass the traffic correctly. If I do, it does not. (I'm testing it trying to connect from the outside and I get a connection in the case of the former, but not in the latter scenario.) I generally choose tcp/aol as my test "public service" and are trying to connect to the external IP address on port 5190, which is the port for tcp/aol.)
  2. At the time wherever I try to do a second mapping, the system rejects saying «server address configuration comes into conflict with a rule of existing translation»
  3. Even if it worked, when I select "Public address specify if it is different from the private service", it only shows me the list of integrated service objects, not everything I've created. This isn't really the end of the world - I could divert just a series of services that we do not - but it would be nice if I could get actually ports my users are already using so that I could make a transparent exchange rather than giving them all the new connection information.

  Any thoughts would be greatly appreciated. I guess I'm missing something pretty obvious, but I'm not that knowledgeable about the Cisco ASA family at this point, I can probably use a few pointers get this working.

  Thank you!

  Hello

  There's something really weird happens with the end of your post. The second section of numbered points has its text completely messed. The lines of text are on top of eachother.

  I don't personally use the ASDM at all to configure ACL and NAT configurations.

  I could help with the configuration of CLI format however.

  Seems that you are trying to configure static PAT (Port Forwarding) for several internal hosts using the public IP address unique who will be on the external interface of the ASA.

  In general, you can use this format for all NAT configurations

  network of the object

  host

  NAT tcp service interface static (inside, outside)

  Naturally, the names of the interface may be different and could be "udp" instead of "tcp". Also since you can configure a large number of these I suggest you come up with a clear policy naming for your 'network of the object' so that they are easy to read and to clarify the purpose.

  Each 'object' that is created can be used on your external interface ACL to allow traffic. However if you want to configure a large number of these configurations PAT static and there are several ports for host even then it might be easier to make different 'object' to be used in the ACL list or it can be annoying.

  Could resemble a basic ACL corresponding to the "nat" above configuration rule

  access list permit tcp any eq object

  Once again the ACL above may look different in your use. You can limit the traffic of certain source addresses that would mean multiple ACL lines.

  Hope this helps

  -Jouni

• General issue of 4215

  I'm quite a beginner to the configuration of the 4215 IDS; However, we have just received our House and I would like to go through setting up with some experts before an extended trial.

  My question, I Fe1/1 and Fe1/2 cables connected to two Gigabit ports on our 6509. I have two destination ports (the ports that connect finally return to the Fe ports on the 4215) specified on the source port 6509 and one (our port router PIX connected to the 6509).

  Given the config below info and details from above, should I correct wiring and this approach works?

  -Config

  vs0 virtual sensor

  Description of the default virtual sensor

  interface logic idspair1

  output

  output

  ! ------------------------------

  service interface

  Physics-interface FastEthernet0/0

  full duplex

  Speed 100

  output

  Physics-interface FastEthernet0/1

  interface of remote sensing Description

  Admin-state enabled

  full duplex

  Speed 100

  ALT-tcp-reset-interface no

  output

  Physics-interface FastEthernet1/0

  Description pair of Sensing - part 1

  Admin-state enabled

  full duplex

  Speed 100

  ALT-tcp-reset-interface-name of the interface FastEthernet1/2

  output

  Physics-interface FastEthernet1/1

  Description pair of Sensing - part 2

  Admin-state enabled

  full duplex

  Speed 100

  ALT-tcp-reset-interface-name of the interface FastEthernet1/3

  output

  Inline-interfaces idspair1

  Original pair description

  Interface1 FastEthernet1/0

  Interface2 FastEthernet1/1

  Ryan:

  Yes it will work.

  Whith your configuration, you will be able to inspect the traffic to and from the Internet.

  In the future I suggest you set up the rest of the interfaces to detect internal traffic. You can COVER a couple of port of the switch (for example, different VLANs) and use of IDS in promiscuous mode.

  I hope this helps (Please note it this post and the previous one).

  Best regards.

  Alberto Giorgi of Spain

• VPN on ASA 5506 without internet access, help with NAT?

  Hello

  I have upgraded to a Cisco ASA 5505 to a 5506 X and as such have climbed to ASA 9.5

  For this reason, I'm a bit stuck on how to implement the VPN. I followed the wizard and I can now establish inbound connections, but when connected (all traffic is tunnel) there is no internet connectivity.

  Our offices internal (inside) network is 192.168.2.0/24

  Our VPN pool is 192.168.4.0/24

  I guess that I'm missing a NAT rule, but in all honesty, I'm a user ASDM and as everything is changed, I am struggling to recreate it?

  Here is my config:

  Result of the command: "sh run"
  
  : Saved
  
  :
  : Serial Number: JAD194306H5
  : Hardware:   ASA5506, 4096 MB RAM, CPU Atom C2000 series 1250 MHz, 1 CPU (4 cores)
  :
  ASA Version 9.5(1)
  !
  hostname ciscoasanew
  domain-name work.internal
  enable password ... encrypted
  names
  ip local pool RemoteVPNPool 192.168.4.1-192.168.4.254 mask 255.255.255.0
  !
  interface GigabitEthernet1/1
   nameif outside
   security-level 0
   ip address 192.168.3.4 255.255.255.0
  !
  interface GigabitEthernet1/2
   nameif inside
   security-level 100
   ip address 192.168.2.197 255.255.255.0
  !
  interface GigabitEthernet1/3
   shutdown
   no nameif
   no security-level
   no ip address
  !
  interface GigabitEthernet1/4
   shutdown
   no nameif
   no security-level
   no ip address
  !
  interface GigabitEthernet1/5
   shutdown
   no nameif
   no security-level
   no ip address
  !
  interface GigabitEthernet1/6
   shutdown
   no nameif
   no security-level
   no ip address
  !
  interface GigabitEthernet1/7
   shutdown
   no nameif
   no security-level
   no ip address
  !
  interface GigabitEthernet1/8
   shutdown
   no nameif
   no security-level
   no ip address
  !
  interface Management1/1
   management-only
   nameif management
   security-level 100
   ip address 192.168.1.1 255.255.255.0
  !
  ftp mode passive
  clock timezone GMT 0
  dns domain-lookup inside
  dns domain-lookup management
  dns server-group DefaultDNS
   name-server 192.168.2.199
   domain-name work.internal
  same-security-traffic permit inter-interface
  same-security-traffic permit intra-interface
  object network obj_any
   subnet 0.0.0.0 0.0.0.0
  object network 173.0.82.0
   host 173.0.82.0
  object network 173.0.82.1
   subnet 66.211.0.0 255.255.255.0
  object network 216.113.0.0
   subnet 216.113.0.0 255.255.255.0
  object network 64.4.0.0
   subnet 64.4.0.0 255.255.255.0
  object network 66.135.0.0
   subnet 66.135.0.0 255.255.255.0
  object network a
   host 192.168.7.7
  object network devweb
   host 192.168.2.205
  object network DevwebSSH
   host 192.168.2.205
  object network DEV-WEB-SSH
   host 192.168.2.205
  object network DEVWEB-SSH
   host 192.168.2.205
  object network vpn-network
   subnet 192.168.4.0 255.255.255.0
  object network NETWORK_OBJ_192.168.4.0_24
   subnet 192.168.4.0 255.255.255.0
  object network NETWORK_OBJ_192.168.2.0_24
   subnet 192.168.2.0 255.255.255.0
  object-group network EC2ExternalIPs
   network-object host 52.18.73.220
   network-object host 54.154.134.173
   network-object host 54.194.224.47
   network-object host 54.194.224.48
   network-object host 54.76.189.66
   network-object host 54.76.5.79
  object-group network PayPal
   network-object object 173.0.82.0
   network-object object 173.0.82.1
   network-object object 216.113.0.0
   network-object object 64.4.0.0
   network-object object 66.135.0.0
  object-group service DM_INLINE_SERVICE_1
   service-object icmp
   service-object icmp6
   service-object icmp alternate-address
   service-object icmp conversion-error
   service-object icmp echo
   service-object icmp information-reply
   service-object icmp information-request
  access-list outside_access_in extended permit tcp object-group EC2ExternalIPs object DEVWEB-SSH eq ssh
  access-list outside_access_in remark AWS Servers
  access-list outside_access_in extended permit tcp object-group EC2ExternalIPs object devweb eq ssh log debugging inactive
  access-list outside_access_in extended permit ip any any inactive
  access-list outside_access_in remark Ping reply
  access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any interface outside
  access-list outside_access_in remark Alarm
  access-list outside_access_in extended permit tcp any interface outside eq 10001
  access-list outside_access_in remark CCTV
  access-list outside_access_in extended permit tcp any interface outside eq 7443
  access-list outside_access_in extended deny ip any any
  access-list workvpn_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
  access-list workvpn_splitTunnelAcl_1 standard permit 162.13.130.12 255.255.255.252
  access-list workvpn_splitTunnelAcl_1 standard permit 162.13.133.72 255.255.255.252
  access-list workvpn_splitTunnelAcl_1 standard permit 164.177.128.200 255.255.255.252
  access-list workvpn_splitTunnelAcl_1 standard permit 164.177.132.16 255.255.255.252
  access-list workvpn_splitTunnelAcl_1 standard permit 164.177.132.72 255.255.255.252
  access-list workvpn_splitTunnelAcl_1 standard permit 212.64.147.184 255.255.255.248
  access-list workvpn_splitTunnelAcl_1 standard permit 95.138.147.116 255.255.255.254
  access-list workvpn_splitTunnelAcl_1 standard permit 95.138.147.118 255.255.255.254
  access-list workvpn_splitTunnelAcl_1 standard permit host 95.138.147.118
  access-list workvpn_splitTunnelAcl_1 standard permit 95.138.147.120 255.255.255.254
  access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 192.168.4.0 255.255.255.0
  access-list workvpn2_splitTunnelAcl standard permit 192.168.2.0 255.255.255.0
  access-list workVPN2016_splitTunnelAcl standard permit 192.168.2.0 255.255.255.0
  pager lines 24
  logging enable
  logging buffer-size 16000
  logging asdm-buffer-size 512
  logging asdm warnings
  logging flash-bufferwrap
  mtu outside 1500
  mtu inside 1500
  mtu management 1500
  icmp unreachable rate-limit 1 burst-size 1
  no asdm history enable
  arp timeout 7200
  no arp permit-nonconnected
  nat (inside,outside) source static NETWORK_OBJ_192.168.2.0_24 NETWORK_OBJ_192.168.2.0_24 destination static NETWORK_OBJ_192.168.4.0_24 NETWORK_OBJ_192.168.4.0_24 no-proxy-arp route-lookup
  !
  object network obj_any
   nat (any,outside) dynamic interface
  object network DEVWEB-SSH
   nat (inside,outside) static interface service tcp ssh ssh
  access-group outside_access_in in interface outside
  route outside 0.0.0.0 0.0.0.0 192.168.3.3 1
  timeout xlate 3:00:00
  timeout pat-xlate 0:00:30
  timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
  timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
  timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  timeout floating-conn 0:00:00
  user-identity default-domain LOCAL
  http server enable
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.2.0 255.255.255.0 inside
  no snmp-server location
  no snmp-server contact
  service sw-reset-button
  crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
  crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
  crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
  crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
  crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
  crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
  crypto ipsec security-association pmtu-aging infinite
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
  crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
  crypto map outside_map interface outside
  crypto ca trustpoint _SmartCallHome_ServerCA
   no validation-usage
   crl configure
  crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
   enrollment self
   fqdn none
   subject-name CN=192.168.2.197,CN=ciscoasanew
   keypair ASDM_LAUNCHER
   crl configure
  
  snip
  
  dhcpd auto_config outside
  !
  dhcpd address 192.168.1.2-192.168.1.254 management
  dhcpd enable management
  !
  no threat-detection basic-threat
  threat-detection statistics port
  threat-detection statistics protocol
  threat-detection statistics access-list
  threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
  ssl trust-point ASDM_Launcher_Access_TrustPoint_0 inside
  ssl trust-point ASDM_Launcher_Access_TrustPoint_0 inside vpnlb-ip
  group-policy DfltGrpPolicy attributes
   vpn-tunnel-protocol ssl-client
  group-policy workVPN2016 internal
  group-policy workVPN2016 attributes
   dns-server value 192.168.2.199
   vpn-tunnel-protocol ikev1
   split-tunnel-policy tunnelall
   ipv6-split-tunnel-policy tunnelall
   default-domain value work.internal
   split-dns value work.internal
   split-tunnel-all-dns enable
  dynamic-access-policy-record DfltAccessPolicy
  
  !
  class-map inspection_default
   match default-inspection-traffic
  !
  !
  policy-map type inspect dns preset_dns_map
   parameters
    message-length maximum client auto
    message-length maximum 512
  policy-map global_policy
   class inspection_default
    inspect dns preset_dns_map
    inspect ftp
    inspect h323 h225
    inspect h323 ras
    inspect rsh
    inspect rtsp
    inspect esmtp
    inspect sqlnet
    inspect skinny
    inspect sunrpc
    inspect xdmcp
    inspect sip
    inspect netbios
    inspect tftp
    inspect ip-options
  !
  service-policy global_policy global
  prompt hostname context
  call-home reporting anonymous
  hpm topN enable
  Cryptochecksum:
  : end
  

  Hi Ben-

  What you are trying to accomplish is called VPN crossed.  Depending on your initial configuration, you have 2 NAT problems.  The first has to do with the NAT you place your order.  In the code later that we are dealing with two NAT ASA 8.3 times and who are ranked 2 sections going on before and after the device NAT. object

  My general rule for control of NAT is like this:

  1. Twice NAT (front) - use this section for exemptions from NAT or unusual configurations that have to go first
  2. Purpose of NAT - Use this section to the static NAT instructions for servers
  3. Twice NAT (after) - use this section to your global declarations of NAT, basically a catch-all

  Then, never use 'all' as an interface for all training of NAT.  This may seem like a good idea, but it will bite you.  Remember, it is more the notion of control NAT, then 'all' interface is bit VPN configurations and similar DMZ.  Always be specific about your interface for NAT pairs.

  To this end, here is what I suggest that your NAT configuration should resemble:

  nat (inside,outside) source static NETWORK_OBJ_192.168.2.0_24 NETWORK_OBJ_192.168.2.0_24 destination static NETWORK_OBJ_192.168.4.0_24 NETWORK_OBJ_192.168.4.0_24 no-proxy-arp route-lookup!object network DEVWEB-SSH nat (inside,outside) static interface service tcp ssh ssh !nat (inside,outside) after-auto source dynamic any interfacenat (outside,outside) after-auto source dynamic any interface

  The key is that you need a NAT device explicitly reflecting the VPN traffic. PSC

• ASA 5505 8.41 dynamic configuration NAT NAT/static

  Hello

  I am having some problems of configuration statements NAT on my ASA5505 which has recently been upgraded to 8.41.

  I have a unique dynamic IP on the external interface of the ASA and wish that all internal hosts NAT/Pat it. In addition, I would like to have multiple ports 'sent' to internal hosts, one of which is TCP/4343. With the current configuration guests originate from the external interface correctly, but the service running on TCP/4343 is not accessible from the outside. See the output of the command below:

  exit "sh run object:

  network of the object DrJones
  Home 10.81.220.90
  network of the LAN object - 10.81.220.0
  10.81.220.0 subnet 255.255.255.0

  exit "sh run nat:

  network of the object DrJones
  NAT (inside, outside) interface static 4343 4343 tcp service
  network of the LAN object - 10.81.220.0
  NAT dynamic interface (indoor, outdoor)

  exit "sh run access-list":

  access extensive list ip 10.81.220.0 inside_access_in allow 255.255.255.0 any
  outside_access_in list extended access permit icmp any any echo response
  outside_access_in list extended access permit tcp any interface outside eq 4343

  Any help would be appreciated, if additional information is needed please let me know and I'll post it.

  Thank you in advance.

  Hi Mitch,

  There are two major changes between 8.3 - pre and post - 8.3.

  1 NAT

  2 interface Access-list.

  You went directly to step 1, but have set up the pre - 8.3 outside_access_in access list.

  The correct config would be:

  outside_access_in list extended access permit icmp any any echo-reply //you can remove this and add inspect icmp to the overall strategy.
  outside_access_in list extended access permit tcp any host 10.81.220.90 eq 4343

  8.3 and above, the access list interface should have the real ip and not the ip translated.

  I hope this helps.

  -Shrikant

  P.S.: Please check the question as answered if it was resolved. Note the useful messages. Thank you.

• The ASA VPN help

  Hello

  The ASA is not my strong point.  I had to make some changes to my ASA clients when the provider has changed.  The ASA has been NAT would be an NTU gave us the previous provider, the new provider of the SAA is NAT had a modem.  The only thing that does not work right is the VPN.

  When IPSec VPN connects we cannot ping, telnet/ssh or RDP to one of imagine.  My guess is that the ACL are not quite right.  Could someone take a look at the config and propose something?

  WAN - ASA - LAN (192.168.20.x)

  I deleted the names of user and password and changed the public IP address around security.

  ASA # sh run
  : Saved
  :
  ASA Version 8.2 (5)
  !
  host name asa
  domain afpo.local
  activate the encrypted password of JCdTyvBk.ia9GKSj
  d/TIM/v60pVIbiEg encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  address 192.168.20.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  PPPoE client vpdn group idnet
  IP address pppoe setroute
  !
  banner exec *****************************************************
  exec banner * SCP backup enabled *.
  exec banner * SYSLOG enabled *.
  banner exec *****************************************************
  passive FTP mode
  clock timezone GMT/UTC 0
  summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00
  DNS lookup field inside
  DNS server-group DefaultDNS
  Server name 192.168.20.201
  domain afpo.local
  permit same-security-traffic intra-interface
  object-group network GFI-SERVERS
  object-network 5.11.77.0 255.255.255.0
  object-network 93.57.176.0 255.255.255.0
  object-network 94.186.192.0 255.255.255.0
  object-network 184.36.144.0 255.255.255.0
  network-object 192.67.16.0 255.255.252.0
  object-network 208.43.37.0 255.255.255.0
  network-object 228.70.81.0 255.255.252.0
  network-object 98.98.51.176 255.255.255.240
  allowed extended INCOMING tcp access list any interface outside eq https inactive
  allowed extended INCOMING tcp access list any interface outside eq 987
  interface of access inactive list allowed extended object-group GFI SERVERS off eq smtp tcp INBOUND
  interface to access extended permitted list INCOMING tcp object-group GFI SERVERS off eq ldaps
  access-list SHEEP extended ip 192.168.20.0 allow 255.255.255.0 10.0.0.0 255.255.0.0
  access-list SHEEP extended ip 192.168.20.0 allow 255.255.255.0 172.16.0.0 255.255.255.0
  access-list SHEEP extended ip 192.168.20.0 allow 255.255.255.0 172.16.0.0 255.255.255.128
  IP 10.71.79.0 allow Access - list extended RITM 255.255.255.0 10.0.0.0 255.255.0.0
  CLIENT_VPN list of allowed ip extended access any 172.16.0.0 255.255.255.128
  Standard access list SPLIT_TUNNEL allow 10.71.79.0 255.255.255.0
  Standard access list TSadmin_splitTunnelAcl allow 10.71.79.0 255.255.255.0
  pager lines 24
  Enable logging
  logging trap information
  asdm of logging of information
  host of logging inside the 10.71.79.2
  Within 1500 MTU
  Outside 1500 MTU
  local pool CLIENT_VPN_POOL 172.16.0.1 - 172.16.0.126 255.255.255.128 IP mask
  local pool SSL_VPN_POOL 172.16.0.129 - 172.16.0.254 255.255.255.128 IP mask
  IP verify reverse path to the outside interface
  IP audit attack alarm drop action
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow 10.71.79.0 255.255.255.0 echo inside
  ICMP allow any inside
  ICMP allow any inaccessible outside
  ICMP allow 86.84.144.144 255.255.255.240 echo outside
  ICMP allow all outside
  ASDM image disk0: / asdm - 645.bin
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 0 access-list SHEEP
  NAT (inside) 1 192.168.20.0 255.255.255.0
  public static tcp (indoor, outdoor) interface smtp 10.71.79.2 smtp netmask 255.255.255.255
  public static tcp (indoor, outdoor) interface https 10.71.79.2 https netmask 255.255.255.255
  public static tcp (indoor, outdoor) interface 987 10.71.79.2 987 netmask 255.255.255.255
  public static tcp (indoor, outdoor) interface ldaps 10.71.79.2 ldaps netmask 255.255.255.255
  Access-group ENTERING into the interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol AAA-server Serveur_RADIUS
  AAA-server host 10.71.79.2 Serveur_RADIUS (inside)
  key *.
  RADIUS-common-pw *.
  not compatible mschapv2
  the ssh LOCAL console AAA authentication
  Enable http server
  Server of http session-timeout 60
  http 0.0.0.0 0.0.0.0 inside
  http 87.84.164.144 255.255.255.240 outside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  resetinbound of service inside interface
  resetinbound of the outside service interface
  Service resetoutside
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  address DYN_CLIENT_VPN 10 of the crypto dynamic-map CLIENT_VPN
  Crypto dynamic-map DYN_CLIENT_VPN 10 the value transform-set ESP-AES-256-SHA ESP-3DES-MD5
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  crypto IPSEC_VPN 10 card matches the address RITM
  card crypto IPSEC_VPN 10 set peer 88.98.52.177
  card crypto IPSEC_VPN 10 the value transform-set ESP-AES-256-SHA ESP-3DES-MD5
  card crypto IPSEC_VPN 100-isakmp dynamic ipsec DYN_CLIENT_VPN
  card crypto IPSEC_VPN 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  IPSEC_VPN interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 5
  life 86400
  crypto ISAKMP policy 20
  preshared authentication
  aes-192 encryption
  sha hash
  Group 5
  life 86400
  crypto ISAKMP policy 30
  preshared authentication
  aes encryption
  sha hash
  Group 5
  life 86400
  crypto ISAKMP policy 40
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH enable ibou
  SSH 0.0.0.0 0.0.0.0 inside
  SSH 88.98.52.176 255.255.255.240 outside
  SSH 175.171.144.58 255.255.255.255 outside
  SSH 89.187.81.30 255.255.255.255 outside
  SSH timeout 60
  SSH version 2
  Console timeout 30
  management-access inside
  VPDN group idnet request dialout pppoe
  VPDN group idnet localname
  VPDN group idnet ppp authentication chap
  VPDN username password *.

  a basic threat threat detection
  scanning-threat shun except ip 10.0.0.0 address threat detection 255.255.0.0
  scanning-threat time shun 360 threat detection
  threat detection statistics
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  NTP server 130.88.202.49 prefer external source
  TFTP server outside 86.84.174.157 /Aberdeen_Fishing_Producers_ (ASA5505) .config
  WebVPN
  port 4443
  allow outside
  DTLS port 4443
  SVC disk0:/anyconnect-win-2.4.0202-k9.pkg 1 image
  SVC disk0:/anyconnect-macosx-i386-2.4.0202-k9.pkg 2 image
  Picture disk0:/anyconnect-macosx-powerpc-2.4.0202-k9.pkg 3 SVC
  SVC profiles ANYCONNECT_PROFILE disk0: / AnyConnectProfile.xml
  enable SVC
  attributes of Group Policy DfltGrpPolicy
  value of server WINS 10.71.79.2
  value of server DNS 10.71.79.2
  VPN - 10 concurrent connections
  Protocol-tunnel-VPN IPSec svc
  enable IP-comp
  enable PFS
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list SPLIT_TUNNEL
  afpo.local value by default-field
  WebVPN
  time to generate a new key of SVC 60
  SVC generate a new method ssl key
  profiles of SVC value ANYCONNECT_PROFILE
  SVC request no svc default
  internal TSadmin group strategy
  Group Policy attributes TSadmin
  value of server WINS 10.71.79.2
  value of server DNS 10.71.79.2
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list TSadmin_splitTunnelAcl
  afpo.local value by default-field
  username password backup encrypted qwzcxbPwKZ7WiiEC privilege 15
  backup attributes username
  type of remote access service
  admin Cg9KcOsN6Wl24jnz encrypted privilege 15 password username
  attributes of user admin name
  type of remote access service
  tsadmin encrypted v./oXn.idbhaKhwk privilege 15 password username
  R60CY/username password 7AzpFEsR ritm. O encrypted privilege 15
  ritm username attributes
  type of remote access service
  attributes global-tunnel-group DefaultWEBVPNGroup
  address SSL_VPN_POOL pool
  authentication-server-group LOCAL Serveur_RADIUS
  type tunnel-group RemoteVPN remote access
  attributes global-tunnel-group RemoteVPN
  address CLIENT_VPN_POOL pool
  authentication-server-group LOCAL Serveur_RADIUS
  IPSec-attributes tunnel-group RemoteVPN
  pre-shared key *.
  tunnel-group 87.91.52.177 type ipsec-l2l
  IPSec-attributes tunnel-group 89.78.52.177
  pre-shared key *.
  tunnel-group TSadmin type remote access
  tunnel-group TSadmin General attributes
  address CLIENT_VPN_POOL pool
  strategy-group-by default TSadmin
  tunnel-group TSadmin ipsec-attributes
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:9ddde99467420daf7c1b8d414dd04cf3
  : end
  ASA #.

  Doug,

  The nat will knit from inside to out if the LAN is 192.168.20.0 nat should be like this:

  access-list SHEEP extended ip 192.168.20.0 allow 255.255.255.0 172.16.0.129 255.255.255.128

  Just to get this clear you use remote VPN, you must add the 192.168.20.0 to split ACL road tunnel:

  SPLIT_TUNNEL list standard access allowed 192.168.20.0 255.255.255.0

  -JP-

• Configure an FTP server behind ASA 5505, need some sort of port forwarding

  My company uses a Cisco ASA 5505 Adaptive Security Appliance, and I'm trying to set up an SFTP server which is accessible from the Internet.

  Is it possible to simply configure port forwarding to my FTP port (4610) to the IP with the server, as I would on a simple Linksys router? Or I have to put in place a sort of demilitarized zone?

  Any help would be greatly appreciated.

  No, you do not necessarily have a demilitarized zone, inside works perfectly. I guess you want to use the ip address of the external interface of the ASA for this? If so, it would looks something like this. Where x.x.x.x is the ip address of the inside/private of the ftp server.

  public static 4610 4610 netmask 255.255.255.255 x.x.x.x interface tcp (indoor, outdoor)

  outside_access_in list extended access permit tcp any interface outside eq 4610

  Access-group outside_access_in in interface outside

• 800 series Router and ASA will not create a tunnel

  Hey everybody, what had confused me for a week now, and I feel that it is something small that im overlooking. My 800 router and my ASA will not pass traffic through a VPN. Here are my configs (less sensitive data of course). I also removed irrelevant data to narrow down the config.

  800 series router:

  DHCP excluded-address 192.168.2.1 IP 192.168.2.100

  !

  IP dhcp pool internaldhcp

  network 192.168.2.0 255.255.255.0

  x.x.x.x where x.x.x.x DNS server

  default router 192.168.2.1

  !

  !

  IP cef

  no ip domain search

  domain IP (domain here)

  Server name x.x.x.x IP

  Server name x.x.x.x IP

  No ipv6 cef

  !

  !

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  address key (password) crypto isakmp (ip WAN of ASA)

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac 3des-sha

  Crypto ipsec transform-set esp-3des esp-md5-hmac 3des-md5

  Crypto ipsec transform-set esp-3des esp-md5-hmac distance

  !

  !

  map KentonMap 1 ipsec-isakmp crypto

  defined peer (ASAs WAN IP)

  the value of the transform-set 3des-sha

  match address 110

  !

  !

  !

  !

  !

  interface FastEthernet0

  no ip address

  !

  interface FastEthernet1

  no ip address

  !

  interface FastEthernet2

  no ip address

  !

  interface FastEthernet3

  no ip address

  !

  interface FastEthernet4

  Description outside the int

  (Local WAN) 255.255.255.252 IP address

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  card crypto KentonMap

  service-policy output VoiceLLQ

  !

  interface Vlan1

  IP 192.168.2.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  Fair/fair-queue

  !

  !

  IP nat pool insidepool (WAN IP) (WAN IP) netmask 255.255.255.252

  IP nat inside source list 100 insidepool pool overload

  IP route 0.0.0.0 0.0.0.0 (Next Hop)

  !

  access-list 100 permit ip 192.168.2.0 0.0.0.255 any

  Note access-list 110 VPN ACL

  access-list 110 permit ip 192.168.2.0 0.0.0.255 192.168.24.0 0.0.0.255

  !

  The ASA config:

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.24.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  (LOCAL WAN) 255.255.255.252 IP address

  !

  permit same-security-traffic intra-interface

  IP 192.168.24.0 allow Access - list extended sheep 255.255.255.0 192.168.2.0 255.255.255.0

  Access extensive list ip 192.168.24.0 LimatoKenton allow 255.255.255.0 192.168.2.0 255.255.255.0

  OutsideIn list extended access permit tcp any interface outside eq 3389

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 192.168.24.0 255.255.255.0

  Route outside 0.0.0.0 0.0.0.0 (Next Hop) 1

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-3des esp-sha-hmac 3des-sha

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  card crypto LimaMap 1 corresponds to the address LimatoKenton

  card crypto LimaMap 1 defined peer (800 WAN router)

  card crypto LimaMap 1 the value transform-set 3des-sha

  LimaMap interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 1

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  tunnel-group (800 WAN router) type ipsec-l2l

  tunnel-group (800 WAN router)

  IPSec-attributes

  pre-shared key *.

  ISAKMP crypto release:

  ASA

  Type: L2L role: initiator

  Generate a new key: no State: MM_ACTIVE

  Router

  DST CBC conn-State id

  (Local WAN)    (ASA WAN)   ACTIVE QM_IDLE 2003

  Hello, Benjamin.

  I guess that your router does NAT same for site traffic to site.

  So, you have to deny traffic between ACL 100 sites.

  PS: If this does not resolve your problem, could you please share isakmp/ipsec its on both sides?