ThinkPad T400 does not start, is turn on below the screen & turning HDD switch off in a loop

Similar Questions

• Tecra 8100 - does not start and no activity on the screen

  Hello

  My Tecra 8100 not start or take me to the BIOS Setup. It lights up, swirls the hard drive, but there is no activity on the display. The only way I can get something on the screen is turning with the F12 key when I get the 'ready for the update of the BIOS. Place the BIOS update diskette in the drive "... message. So I tried the traditional method of updating the BIOS, found on the Toshiba site, but nothing helped. The machine seems to read the disk (that contains the downloaded BIOS) but does nothing. It is just there for centuries, with the disk light.

  The last two days I have trawled thro much views and even took the whole machine goes to check the connections loose, but I found no answer yet.

  Can someone out there please help?

  Thank you very much

  Hello Rory

  I did the BIOS to be updated several times, but I've never seen this message at startup upward. You did it the traditional method as described in the document which you will find under http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/faq.jsp?z=234&service=EU&from=faq_selection&CFID=B IOS & FID = TRO0000000b07?

• Samsung S3520 does not start after that I changed the screen he wants more F2 or F4

  F2 TO SET UP

  AND

  F4 FOR RECOVERY

  BUT F4 DOES NOTHING

  AND F2

  THIS LAPTOP HAS WINDOWS 7 SUPPORT AND WORKED PERFECTLY UNTIL MY BROKEN SCREEN

  NOW THE SCREEN IS BACK WORKING I CAN'T BOOT MY LAPTOP

  ANYONE HAS ANY IDEAS PLEASE?

  Hello

  Thank you for the update.

  I suggest you run bootrec commands and check.
  Reference:
  Use Bootrec.exe in the WINRE to resolve startup problems
  https://support.Microsoft.com/en-us/KB/927392

  You can create the media to install Windows 7 from this link:
  https://www.Microsoft.com/en-us/software-download/Windows7

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• My ThinkPad T400 does not start!

  Honestly, I have no idea what could have caused this!

  I turned it on this morning & it was stuck on the startup screen. It read "ThinkPad" in big letters followed "To interrupt normal startup upward, press the blue ThinkVantage button." Waited about half an hour for him to start & it never did. Of course I pressed the ThinkVantage button & to my dismay... nothing happened. Subsequently, I have unplugged it & removed the battery. I then plugged it back in & tried to start again. Once again, nothing. I unplugged it new & attached to the battery. At this point, I tried to go back to the top and N O T H I N G!

  What should I do?

  Take a look at your usb ports, there could be some sort of pins to touch, as a result of the damaged usb pins.

  ADMIN Edit - link to related in our forum KB Advanced

• Since my computer downloaded the auto update: hotfix for windows XP (KB2570791), it does not start in place... the screen goes all black. I can only start in safe mode.

  I restored the computer to a previous point, but as soon as I stop and restart, the same thing happens. ??

  Hello

  You can try the steps listed in the link: after the Windows Logo appears, or after you log on Windows, a Windows XP computer can display the wallpaper, a black screen or a blue screen: http://support.microsoft.com/kb/318027

• T400s does not start after cleaning the keyboard

  Hello. I cleaned by T400s keyboard today after a few juice reaches the keys and the laptop does not start anymore. I removed the battery and the power cord, tried to deceive the 10 times, press the power button / stop, no still no results.

  Reset the CMOS does solve the problem?

  At first glance it seems that the laptop is powered LED fingerprint reader is turned on, but it turns off as soon as I unplug the charger.

  Any suggestions? Thanks in advance.

  This probably means that your keyboard is dead and need a replacement, which is pretty cheap from ebay.

• my windows xp does not start and it only shows the arrow and a black screen in the Middle, what can I do to solve this problem. __

  my windows xp does not start and it only shows the arrow and a black screen in the Middle, what can I do to solve this problem.

  Try to restart your machine and pressing F8 before the spash screen Windows appears.  Choose the option "last last known good configuration".

  If this fails, you can try to repair your installation of starting for the original CD-ROM for Windows XP installation and choosing the option 'Fix' when prompted.

• Anyone know how to get your money back?  My CC application does not start and I have tried the suggested workaround solutions listed above and they have not worked for me.  The amount of problems listed here in the forum, I have to ask the product is real

  Anyone know how to get your money back?  My CC application does not start and I have tried the suggested workaround solutions listed above and they have not worked for me.  I'm new to the CC Apps but use the versions installed for years.  The amount of questions listed here in this forum, I have to ask the product is really stable?

  Thank you.  I've deleted and reinstalled.  Seems to have solved the problem.

• T400 does not start after the first display screen

  What is going on? I have wss to work today and my computer shut down due to the low batt. I got home and plugged in and waited a few minutes and turned on. When I checked swipe my fingerprint, all that I saw the first startup screen told me I want to interrupt normal off set up that I can close the button think vantage. It is stuck there. I can activate it on and but it does not start after that screen. What can I do? I am in the middle of the drafting of the report and cannot access my docs!

  I looked the problem and found that have been in contact with the usb pins! Yay the prob is fixed!

• Help my pc does not start after you have uninstalled the video driver

  Please help my pc usually start more after I uninstall my nvidia driver mx/mx 400 with YourUninstaller I try to use this option to uninstall my driver in super mode then prompt YourUninstaller and asked "do you want to restart your computer now" then I click Yes but YourUninstaller software now on the race because the YourUninstaller has finished remove the registry left behind by uninstalling normal after that there is no register found after scanned. Then I click Next, then I closed this request. Then I restart my computer manually but blocked windows then I wait 5 or 10 minutes, but do not restart Windows. I turn off my APR, then I turn on my pc then windows does not start. I try to reformat but it's the same story that windows does not start. I try to remove the cmos battery hoping it will solve then it works. But the problem is that I insert my bootable cd, it runs automatically even I don't not press a key on the keyboard, the process to continue installing windows, it sounds I can not install my windows correctly. When he restrart the process goes again to load all the drivers everywhere why did this happen? Is there something wrong with my HARD drive once I used YourUninstaller?

  RAM of a problem with you, I guess. Remove the RAM and clean including the slot of the motherboard.

  http://www.computerhope.com/beep.htm

  If this post answers your question, click mark as answer .

• XP does not start normally. Must use the F8-last known good configuration.

  For the last three days, XP does not start normally. I use F8 and you select last known good configuration that worked. It gets old. If I try to boot normally, it freezes on Autontfs not found I have a MSI wind Pc with Windows XP Service Pack 3.

  Hello Susanherna,

  The last known good configuration is created during the logon process. This means that something has changed between the time that connect us and time that shut down us the computer.

  At the next startup, select instead of last known good configuration safe mode.

  We want to then try a clean boot.

  The following articles describe this process on Windows XP:

  http://support.Microsoft.com/kb/310353

  http://support.Microsoft.com/kb/316434

  Let us know what are the results of this and we will continue from there.

  Best regards

  Matthew_Ha

• Windows Vista does not start upward, with success since the closure complete

  Hello world

  I actually had this problem for a long time, but I'm just now to a point where I'm ready to take a lead in fixing it.

  I can't identify when it started, but Windows Vista does not start upward, with success of a full stop. He gets to the screen where, in general, the green bars will travel across the screen, but the green bars will not come. The screen looks dim and sits there, with the text of the copyright of Microsoft Corporation. So, after not having on the mound, I have to manually shut down the computer by holding down the power button. When I try to start again, told me to go through the Startup Repair tool. If I jump the repair, I just have to meet the same problem - a computer that will not go beyond the screen "green bar".

  So, I do the Startup Repair, and told me what I do for the restoration of the system. Windows starts normally after the restoration.

  Don't forget, this happens from a full stop. To remedy this, I just never completely shut down my computer. I left running and back just at the beginning of the day. The computer may start restart, it just may not start with a full stop.

  Given the start of repair takes, literally, around 4 or 5 hours of full stops complete, accidental or power outages are a nightmare, I am obliged to wait 5 hours to get access to the computer. Fortunately, I have my laptop.

  If someone has encountered this? I saw people talking about the loop of startup repair, but that's not the point, I have. I have yet to see any discussion of my specific problem.

  Thanks in advance!

  Hello

  4-5 hours to do a startup repair is too long.

  Often you get better results if you a using a DVD of Microsoft Vista startup repair.

  Jose how to do a startup repair, etc. using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  See you soon.

• INSTALL A PROGRAM DOES NOT START AUTOMATICALLY, IN VISTA WHERE THE COMMAND IS RUN?

  PROGRAM DISK DOES NOT START AUTOMATICALLY, IN MS VISTA WHERE THE COMMAND IS RUN OR HOW DO I INSTALL THE PROGRAM?

  Click Start > programs > Accessories > RUN.

  http://www.howtogeek.com/HOWTO/Windows-Vista/enable-run-command-on-Windows-Vista-Start-menu/

  Link above will help you.

  http://www.mydigitallife.info/2007/02/17/how-to-open-elevated-command-prompt-with-administrator-privileges-in-Windows-Vista/

  And this will interest you as well.

  See you soon. Mick Murphy - Microsoft partner

• Lightroom CC (2015) does not start under win 10 of the programme. The diagnostic program announces that Lightroom is not compatible. I have installed several times and disconnected. LR does not start. Program of liver, but it does not work. How can I fix

  Lightroom CC (2015) does not start under win 10 program.
  Program diagnosis announcement only Lightroom is not compatible. J’ai installed several times and disconnected. LR does not start. Hepatic program, but it does not work. How do I correct?

  CHETNA Hello!
  It works again! Thank you and have a nice day!
  Snowy greetings from Finnish Lapland.

  Thank you

  Veikko Hamara

• SRM does not start after you have moved the database

  We're under 4.1 SRM and moved its sql database to a new server sql (new server sql a different host name).  We moved successfully to the virtual center & Manager Update bases sql data, but after moving srm4.1 database, the srm service does not start...

  so far, I uninstalled SRM (DO NOT remove the SRM database)... After uninstalling SRM, I rebooted the server.  Then I have re-directed the SRM installation and started going through the installation of MRS... After pointing the SRM installed on the server vcenter, port 80, and pointing to an existing sql database, etc., I get a thumbnail of certificate message and a prompt on the creation of a new certificate, which i say 'yes' to... Installation continued on and arrived at the end when it says "create certificate"... then does not say "cannot install the certificate...". Database error has occurred. "At this point, the installation failed

  Any ideas on how to remove the old certificate or work around this error?

  Thank you

  I think the error message is misleading in this case and the problem is not related to the certificate.

  I still think that it is permission DB / configuration number.

  Following links may be useful:

  http://communities.VMware.com/thread/212157

  http:// http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1015883

  Michael.