This device cannot start. (Code 10)

I accidentally deleted my sound driver and have more noise. the error message im receiving to the IDT codec high definition: this device cannot start. (Code 10)

Hello

1. what operating system is installed on your system?

2. did you of recent changes to the system before the show?

Method 1:

Follow the link below and follow the steps and check if it helps.

http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

Also, check out the link below and see the description of the error code 10.

Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

http://support.Microsoft.com/kb/943104

Let us know if it helps.

Tags: Windows

Similar Questions

  • Satellite Pro A10: New card wireless Atheros/Askey, but "this device cannot start" code 10

    Hello

    I have a Satellite Pro A10 and bought an internal pci wireless adapter. The following information is displayed on my card:

    Askey WLL3070-D4 (MOW)
    Atheros AR5BRB-43

    I installed the card, attached to the ariel and turned on the laptop... the switch at the front lights up now and Windows xp detects the new ethernet adapter. My problem is the following...

    Any driver I install (and Ive tried all the drivers of the first 20 + pages of yahoo/google Askey/Atheros etc.) the card installs very well but then in device manager has a yellow! next to him and says this device cannot start (code 10)

    I am really puzzled. I have little ram more to come in the next few days how I am installng Vista im hoping sort my problems, but someone has any ideas?

    I have not yet find a driver which specifically refers to the AR5BRB or the WLL3070-D4 model number.

    Does anyone have a location for a pilot, etc.?

    Thank you

    Hello

    I always use this page for WLan driver update:
    http://APS.toshiba-tro.de/WLAN/

    It is a Toshiba WLan driver portal and you will find all the necessary drivers for WLan

    Ciao

  • Installation of driver with PXI-8360 error "this device cannot start - Code 10"

    While trying to install PXI-6541 to the PXI-1036 chassi with controller PXI 8360 [express-8360 side laptop], the error message "this device cannot start [Code 10]" laptop is Lenovo T60 with the latest version of the BIOS

    Thank you

    Manu

    Sounds great Manu,

    I also followed on that for you, then you should be getting approval sometimes today.

    I hope for the best

  • "this device cannot start (code 10)", which means code 10?

    I was alarmed because I could stop my computer because of a 'message' came onto my computer and I was able to get off. So he would'nt stop. I was installing some new drivers with my Scanner Driver Uniblue, when this happened and so I Google'd up Uniblue to see if I could know what I could do about it, and I found there an investigation on the system cleaners and uniblue was last on their list of 5 questioned, and there were a few bad reports on this subject. I also had on my system, cure of Parelogic pilot, who had slipped completely under my guard through an email from the author of 'Math better explained', an e-book that I had downloaded some time ago and I have now seems to be a fake email because when I looked towards the top of Parelogic there was so many complainants and we even said that they do absolutely nothing positive and in fact that their objective is to implant the computers people and they must be reported to the FBI.

    In any case I finally understood how to disable the offending message. But now I'm worried about 10 network cards that have yellow triangles with! "s with the message"this device cannot start (Code 10) ". It's probably just because I have no network connection, but I can't be sure until I have find this code 10 means,.

    Thank you for your trouble,

    calicoghotmail

    Hello calico.ghotmail,

    My apologies for the delay in the response to this topic.

    Code 10 means that a device could not start.

    If there is no network connection on this computer, then this might be a possible reason for this error.

    Let us know if you have any questions.

    Best regards

    Matthew_Ha

  • in the Device Manager window.there is a brand of (!). Microsoft tun miniport adaptor.this device cannot start. (code 10)

    in the Device Manager window.there is a (!) brand microsoft tun miniport adaptor.this device cannot start. (code 10) hmendezlopez

    Hello

    Control Panel - Device Manager - do right click on them - UNINSTALL - REBOOT

    Nothing else to do, Windows will do the rest. And you can ignore the errors altogether if you wish
    and on some computers, it will always be there but don't cause any trouble.

    On a Windows Vista-based computer or on a Windows Server 2008, Microsoft computer
    ISATAP map appears with a yellow exclamation next to it in Device Manager and you also
    error message
    http://support.Microsoft.com/kb/932520

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • This device cannot start code 10 and could not open selected port

    I load the driver for my track past tracking key Pro and I get the message that this device cannot start code 10. I show no upper or lower filters so the troubleshooting on found here does not work.  If I go to program followed past and then look for the device I get the message could not open selected port.

    I tried all USB ports and they work with other devices. I have a Toshiba satellite running windows 7.

    The company was no help.  Can someone help me please?

    Thank you

    Liz

    Your best bet is to contact the developer again, we have no knowledge of their products.

  • Microstoft ISATAP adapt: this device cannot start (code 10)

    I've had no internet access for a few weeks - a day that worked and then the next day no wi - fi or Ethernet connection. Someone on the MS Community suggested to install driver updates, but the laptop in question has no access to the internet and has been updated automatically anyway. Today, I tried to reinstall the drivers on the adapters wi - fi and broadband from the phone itself, which seemed successful. But when I got to the ISATAP Protocol would not do the same thing and it comes up with the error message in the title of this post.

    I read a few posts, which suggest to uninstall the adapter and then put it back, but as my laptop has no way to connect to internet, I don't see how it will work in my case. I don't seem to have the Win 7 CD either, unfortunately. So, where do I get a new adapter or update the driver, or whatever I need to do?

    Thank you

    IRB

    Hi Snarli,

    Thanks for posting the query on Microsoft Community.

    I understand that you are unable to connect to the internet and that he wants to know if you will be able to re - install ISATAP Adapter without an internet connection or not.

    I suggest you to run the troubleshooter and check if it helps.

    Hardware devices do not work or are not detected in Windows:

    https://support.Microsoft.com/en-us/mats/hardware_device_problems

    You will be able to install base drivers to restart the system after installation.

    If you have any other computer where you can download the driver and the copy to an external hard drive or USB key, you can go ahead and uninstall the driver and restart the computer. Is it does not automatically get installed, and then try to install it by using a USB key.

    You can consult the advice given by Vinod N replied on 26 April 2011.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/this-device-cannot-start-code-10-Microsoft-ISATAP/dc43be6f-466F-E011-8dfc-68b599b31bf5

    I hope this helps to solve the issue. If the problem persists, get back to us. We will be happy to help you.

  • In a work previously Win 7 Pro Shuttle system, we are now "this device cannot start (code 10)" with high defination driver.

    The system with the problem is a shuttle G2 7600 with Windows Home Premium 32 Bit, AMD Athlon II X 2 ' dual core 2.9 HZ.  The sound is integrated 5.1 audio channels.  This works installed sense July 14, 2011.   We now have no audio.  After the properties of the device, see the "this device cannot start (code 10)" someone can help me with this problem?

    Hi Jack,

    You did changes to the computer before the show?

    The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues.

    I suggest you try the steps from the following link:

    Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

    http://support.Microsoft.com/kb/943104/en-us

    Come back and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

  • Canon HG20: this device cannot start (code 10)

    Hi all

    My Canon HG20 camcorder works well on Windows XP. But it's not on Windows 7 64 bit.

    Here's what happenning:

    -The camera is recognized when I connect (via USB) to the PC photo transfer mode.

    -It is not recognized when I connect (via USB) transfer of film mode.

    -In "Devices and printers", the camcorder is shown, but with a yellow exclamation mark on it, notify a problem.

    -The properties panel (right click-> properties) shows "device status: this device cannot start (Code 10)".

    -(Right click-> troubleshooting) troubleshooting completed but fails: "USB mass storage has a driver problem.

    Any suggestions would be greatly appreciated.

    Thanks in advance.

    Hello

    You can try to launch its convenience store and check out what he has to say.

    Here's how you can do:
    1. click the Start button, and then select devices and printers.
    2. right click on the mouse and select troubleshooting.

    I also suggest to install windows update and check if that helps. Also update the drivers chipset, for this you may need to contact the manufacturer of your computer.
    See the article below to install windows update.

    Install Windows updates
    http://Windows.Microsoft.com/en-us/Windows7/install-Windows-updates

    Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
    http://support.Microsoft.com/kb/943104/

    http://www.USA.Canon.com/OPD/controller?Act=OPDSupportDropDownAct
    http://www.USA.Canon.com/OPD/controller?Act=OPDContactUsAct

    Hope this information is useful.

    Umesh P - Microsoft Support

  • We get an error "this device cannot start" Code 10 on Windows 7.

    Original title: USB not recognized verified work storage device

    I have a 8 GB USB Flash drive that has, until recently, worked perfectly on several OSes including Windows 7 and 8. Recently, the player does not seem to want to work on one of my installations of Windows 7 on a PC (HP EliteBook 8470p).

    I tried to reinstall the drivers for it on my machine specific windows 7 that does not work on. Device Manager gives me "this device cannot start. (Code 10) "even after reinstalling the drivers and reboot several times. I use also some virtual machines in Windows 7 and 8 on the same PC, and when connecting virtually the USB key to the virtual machine to Windows 7, I can't detect it. When you connect the device to the virtual machine from Windows 8, I can access the files and even format, so the USB ports on my computer are all functional.

    To summarize, the device works in Windows 7 and 8 separate facilities of this computer, but does not work on 7 on my TI, if the main or virtualized operating system. The VM of Windows 8 on this computer can recognize the device.

    Thanks for the answer, except that I discovered the problem. I checked upward in the disk management window, and I saw that the reader, for some reason, was not assigned a letter. After you manually assign the drive letter, all data on the disc is now available. Thanks anyway.

  • Headset (headphones and microphone) USB - this device cannot start - Code 10

    Hello

    I just bought a USB headset today and tried to use it.  I had a driver error message when first plugged in.  The help system has proved to be unnecessary.

    After doing some research on this forum, I checked the Device Manager and found that the indicatses of properties of USB audio device "this device cannot start. (Code 10) ".  Forum entries suggests that a lot of people have similar problems.

    Mine is a new installation of 64-bit Windows 7 on a new hard drive, but on older hardware of the PC - Asus A8N SLI Premium.  Someone at - it had suggestions as to the resolution of the problem.  Note that a normal headset worked fine yesterday (but I broke it) plugged into the jack Sockets, but I wanted to use a USB headset to avoid having to continue to go to the back of the computer to replace my system 2.1 speakers.

    Thank you

    Hello

    The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

    I suggest you follow the steps in the link below and check if it can help solve your problem.

    http://support.Microsoft.com/kb/943104

    Please reply back and let us know the status of the issue.

    Azam - Microsoft technical support.

  • Computer shipped with cd burner. When I go to burn a cd, it says to connect the burner. In the properties of the device, it says this device cannot start (code 10)

    Cannot read cd of either.

    Hello

    Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
    http://support.Microsoft.com/kb/943104/

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Try this fix manually if the Fixit 314060 does not work
    http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

    Your CD or DVD drive is missing or is not recognized by Windows or other programs-
    a Mr Fixit
    http://support.Microsoft.com/kb/982116

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    for Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
    Vista installation after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and
    the correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD/DVD settings
    drive from someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
    nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

    DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
    devices and their properties in flat table, instead of the tree viewer
    http://www.NirSoft.NET/utils/device_manager_view.html

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Microsoft isatap adapter, get the message "this device cannot start code 10".

    have you tried the driver from the web and update manually update but it States driver is up to date?

    Hi"

    "Description of errors related to the 10 Code that generates the Device Manager in Windows on computers"

    http://support.Microsoft.com/kb/943104

    But it's the information from Microsoft Isatap adapter:

    "On a Windows Vista-based computer or on a computer Windows Server 2008, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message"

    http://support.Microsoft.com/kb/932520

    See you soon.

  • This device cannot start (Code 10) - high definition Audio Device AND opening. VHD files.

    Just upgraded from Vista professional to Home Premium 7.  (Which means that I couldn't have the installationl UPDATE and had to go for CUSTOM).  In hindsight, not a good idea!
    1. no sound from speakers.  I tried updated driver.  Problem is with the Microsoft high definition Audio Device.  Using T9404 of advent, Intel R, HD 400 G, 1 G of RAM.  Speakers are not muted and sound card worked fine with Vista.
    2 had a full backup in Vista immediately before moving to 7; But - guess what - can't open. VHD files for the look, or use it!
    Any help would be greatly appreciated
    Concerning
    AL

    His problem solved.  For the benefit of others in the same boat, that's what I did.
    After trying everything I could think of, I had another look at the system clean.
    Computer >
    Drive C (double click) >
    Request >
    Driver >
    Sound >
    Select Configuration, right-click, choose Run as administrator >
    Wizard starts, select 'Reinstall using your computer settings' >
    Reset.
    Hey its nice and presto!  (Which almost took off my head, because I had forgotten that the speakers were entirely upwards).
    Shows Device Manager now that one mistake, on the network controller - anyone has any information about it, what it does, what application it is associated with etc.
    Concerning
    AL

  • This device cannot start (Code 10) - referring to the CD-ROM/DVD-ROM internal drive.

    Since yesterday I get the message above regarding my internal CD on my Acer laptop drive.

    The PC is barely over a year old & the Cd-Rom works fine up until now.

    I recently moved from Windows Vista Home Premium to Windows 7 Professional (about 2 weeks ago) and the CD-Rom drive has been used successfully to restore all my backup files that W7 is a new installation (not an upgrade).

    I removed the CD-Rom drive (a device slimtype DVD ADS8A2S Philips - Lite-on according to its label) and have re-connected it, but it still does not work.

    Windows seems to see the device when I say add a device, but when he tries automatically configer it I get the message "there is a problem with the driver for Slimtype DVD A DS8A2S ATA Device. "Reinstall the driver may resolve this problem" and gives me the ability to "Apply patch" or "jump the fix. When I choose "Apply patch" I finally get the message "device driver software not properly installed" - Please consult the manufacturer of your device to help... »

    Someone at - it ideas why all of a sudden I get a problem with my CD, I can not restore to any previous backups that I need a CD-Rom drive to do? In the meantime, I'll do a search in the site of compatibility of Windows to see if I can find a match for my camera and what he said about it.

    PS. the only thing different (new) I did just before I lost my CD-Rom has been thast I had linked to a conversion cassette tape via a USB device that my wife wanted some songs from an old tape of copy on CD. Tape copied OK and was transferred to the software iTunes on the PC, but when I said that I wanted to "Burn" the selection in College, I noticed that my CD-Rom (player 'E') show is no longer on my PC configuration, only on disks hard "C" and "D". If this has an impact on my problem, I don't know - it could just have been a co-fact?

    The following MS KB article may help:

    http://support.Microsoft.com/kb/982116

    Try the auto fix (Mats - Run.dvd.exe) and if that doesn't work try following the steps for Windows Vista, which should also work for Windows 7.

    These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

    Create a System Restore Point beforehand and restart the computer later.

  • My computer does not detect my built-in webcam, Device Manager indicates this device cannot start (code 10)

    I have a sony vaio laptop model: model PCG - 71912L: VPCEH32FX
    I went on the sony website and downloaded the driver and installed 4 times and still not a not detect.
    I did all the updates and no results.
    They just replaced my laptop screen and which could have been the cause of the problem, maybe it does not detect the new hardware.
    Tried everything I could do so via Device Manager and nothing.
    Please help, thanks.

    Hello

    What is the brand and model of the webcam?

    Method 1
    I suggest you to run the fixit from the following link:

    Hardware devices do not work or are not detected in Windows
    http://support.Microsoft.com/mats/hardware_device_problems/en-us

    Method 2
    I suggest you to see the following link for the associated 10 error code.

    Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
    http://support.Microsoft.com/kb/943104

Maybe you are looking for

  • Cannot get my wireless printer to print from my laptop

    I'm trying to get my HP Photosmart Premium Print-Scan-Copy all in one printer C310A to print from my PC Compac Presario CQ57 - 229 portable WM.  Now, my problem was first of all that the regular download a driver will not work on this combination bec

  • HP G62 b01ET: display types: System 67596881 disabled

    Help, please: Laptop of HP 2000 crashes after 3 attmpts to enter the administrator password! Display types: System off 67596881 Thanks in advacne!

  • Backlight broken in Satellite A100-405

    Last weekend, my laptop screen remained black never work again. I tried to find a new backlight, but I heard that it is not possible to order this. Maybe it is? Anyone know the part number? There is quite a price difference... a backlight or a new sc

  • Cannot find the shared library nilvaiu.dll and nican.dll.

    I'm using Labview 8.5.1 on windows XP 32-bit systems. Recently, I installed labview on a 64-bit XP system.  I feel what I think, problems of drivers on the 64-bit system, now. When executable files are run files are not: nilvaiu.dll and nican.dll.  S

  • Microsoft Security Center

    When I start windows I get a security WARNING 'Microsoft Security Center is turned off?Mollser