Time capsule: no backup, device not found but internet work

Similar Questions

• Device not found, but internet work

  I have an Airport extreme with a capsule 2 TB that I use as a backup file.

  All of a sudden I can't connect to the airport time capsule. When I launch the airport utility, there is an orange triangle/exclamation point that fits the description "device not found". The router works well, since I am connected to internet (at this time).

  I tried to unplug the unit and time capsule comes back for about 2-3 minutes until the same problem occurs again. Factory of Soft and hard resets produce the same results. I know this isn't my macbook pro because it does the same thing on my phone as well.

  You have Back to My Mac configured on the TC with your AppleID?

  This has happened to me and when I removed my AppleID and disabled Back to My Mac it ceased to occur and the TC became visible again.

  I hope that Apple will fix this soon but it would pay record a call of support with Apple on this topic as well.

• Link to Word Doc and different link to PDF fails not found, but link work I.E.

  The document to download or open either but in Firefox the link of the document when you click on the poster not detected.
  The link is here:
  http://janetmitchellmediator.com/training.html

  Hyperlinks need to use slashes. It should work.
  http://www.janetmitchellmediator.com/TrainingJuly2014.doc

  Thus, you will need to adjust the html code of your site.

• 15 - p030nr: Boot Device not found

  Need help on how to fix a problem where it says "boot device not found." He worked to find one day and the next time I turned on the computer, she appeared with this error message. After reading some things, it seems that it is a right of common mistake around the 1 year mark, but I don't know which is correct. Are there methods I could do to fix this problem.

  OK, if it was an old PC, my guess would be that the hard drive is a failure, but on a PC old of a few months, it is unlikely.

  However, it would be interesting to follow these instructions to check the hard drive:

  Presume withdraw OK, what might work is booting from CD or USB and running CHKDSK to see if this helps to repair the file system.

  CHKDSK is the short name of a utility that provides MS that will do a check of the file system and attempt to repair problems.  A damaged file system may prevent your computer to start correctly and get to a Windows desktop.
  
  Because you can not boot from your PC, then you need to download one of the following options and follow the instructions it contains to make a bootable USB stick or a CD:
  (1) miniTool Partition Wizard
  (2) EASEUS Partition Master
  (3) assistant Partition AOEMI
  
  Once the media, boot from it and use the option to check the disk.

  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• Airport Time Capsule device not found

  I have the time Capsule on the airport of the TB 3 802.11ac (bought 9/2014).  It integrates the latest version of the 7.7.7.  Just last week, I received the error device not found (.. .has been previously a part of your network... etc.).  The internet connection is always good and the component of the time capsule router still works.  When I unplug the device, it can find him but eventually will go down in a few minutes.  I also did a warm reboot, but some results.  Printer connected to the time capsule does not, nor does Time Machine back ups.

  Would be grateful of any advice on why the drive not found error continues to occur.  Thank you!

  You have Back to My Mac enabled on the Time Capsule?

  If so, turn it off for the moment in the AirPort Utility and restart the time Capsule.

• Performance of Time Capsule and "device not found".

  I am now on my 2nd TC average weeks because I thought the first was broken-, but I get the same questions on the second >

  1. A Wi - fi connection is very intermittent.  Seat 3 feet of the TC, I can get 450Mbps on my iPhone 6 and 5 minutes later her stockings to 2Mbps or less (measured on the Wi - Fi Sweetspot app).  Similarly, the speed of connection internet test ranging from 20-30Mbps until 0.3Mbps not it depending on the strength of the wifi.
  2. Air utility sometimes connection works and see the TC.  But often it is not.  First he asks the password, maybe 2 or 3 times.  Can I get a yellow triangle showing on utility AP with "Device not found" and the only option is to Forget.  The TC IS still there, but since I use it for ethernet and wifi internet access still works because I am always online.

  So, what speeds SHOULD I get the Wi - Fi, 3 feet of the TC - I would have thought higher?

  Why WiFi speed decreases considerably, sometimes in the same place?

  Why the Airport utility is not the device, when it is still there?

  Is this a general problem with TCs?  Is this another duff, one back?

  Thank you

  Update you the firmware to 7.7.7 in the TC?

  If all tests performed 7.7.7 then downgrade the firmware to 7.7.3 as he could work much better.

  If it still fails I just return it.

  They seem to vary a lot in quality of construction. Some work OK but many have problems... and when you Exchange to the same store you get another from the same lot.

  There are a lot of articles on wireless diagnosis.

  for example, from your Mac.

  Use Wireless Diagnostics helps you troubleshoot Wi - Fi on your Mac - Apple Support

  Follow the wireless in a few days... and use ethernet if possible... Wireless is never a reliable substitute for ethernet.

  iOS

  If your iPhone, iPad or iPod touch connects to a Wi - Fi - Apple Support network

  A lot of wireless issues with each new version of iOS... he could so your phone that is the problem, not only the TC.

  https://www.YouTube.com/watch?v=j4qgH8uyOk0

  You should check how wireless is around you and the intensity of the signal of all devices.

  I also need to know the exact of the TC configuration and your network if you want to find the problem. Although problems with the Wi - Fi in the TC would be not at all unusual.

• Time capsule is not displayed but the work of WIFI connection

  Hello

  I have a Time Capsule 2 giga, which is used as a WIFI router connected to my normal router via Ethernet and an Airport Extreme, main, used as extension. Until today everything worked well.

  Now, when I open the Airport utility to display the connection, it shows me that the TC and AE are not registered more (device not found). But I can still access the Wifi and internet via networks, I created, but not the backup.

  I unplugged the TC and AE, reconnected them, reset, then the connection worked.

  But now it is again.

  Does anyone have the same problem?

  Concerning

  Unfortunately, this issue is not new and has been reported a number of times since OS X Mavericks.

  AirPort Utility is based on both the mDNS (aka, Hello) and IPv6 IP protocols to find an AirPort base station.

  When access to the airport through the AirPort Utility, try the following, in order, accessibility with the utility check after each step:

  • Check the local connection. If you try to access the airport wireless, make sure that you are connected to its wireless network before running the AirPort Utility to administer it. If you are still unable to access it with the utility, temporarily connect your computer directly using an Ethernet cable to one of the base station's LAN ports.
  • Try to access the base station using the utility file > configure other... option. Then enter the IP address of LAN - side base station (the default value is: 10.0.1.1) and password of the administrator of the base station.
  • Make sure that the base station and your computer are configured for IPv6 link-local only.
    • For a Mac: System preferences > network > Wi - Fi or Ethernet > advanced > TCP/IP tab > configure IPv6: link-local only
    • For the AirPort Base Station:
      Note: You may temporarily connect your Mac or PC directly to the base by Ethernet station to access.
      • From a Mac: AirPort Utility > select the base station > change > Internet tab > Internet Options... > configure IPv6: link-local only
    • Since an iOS device: AirPort Utility > tap the base station > press Edit > tap Advanced > tap on IPv6 > change configure IPv6 to: link-local only > Tap actually
  • The base station power cycle. Remove the power branch of the socket adapter and then wait 15 seconds before plugging back in.
  • Perform a ' default ' reset on the base station.
  • Finally, if you try to access the Airport via an Ethernet connection, make sure that your Ethernet port is NOT configured for Jumbo frames, that is, by using a MTU of 9000 +.

• I try to use my Time Capsule as external hard drive. But when I look in the Finder, nothing is available for shared devices.

  I have a Macbook air running OS X El Capitan. I try to use my Time Capsule as external hard drive. But when I look in the Finder, nothing is available for shared devices. I don't know if I need to restart the time Capsule or change the wireless setting, etc. ?

  Please advise...

  The TC appears in airport utility? If not then it is probably not part of your network or is lost... upgrade installed you El Capo because there a lot of questions.

  What is the TC plugged into the network by ethernet? And configured properly? Are you to internet via the TC... but can not see his drive... that would be typical?

  Have you set Finder preferences to display the network drives? Apple keeps making it difficult for some unknown reason.

  You actually have to mount the drive TC if it appears under shared... it still may not appear if you double click on it. Under the search box on the top of the right hand you see Connect (As) box, type the name or IP address of the TC in there... Make sure that you save the password from your keychain.

  I try to use my Time Capsule as external hard drive

  For the storage of the files it is fine.

  For the execution of direct files for an application in the Mac, you are very likely to damage or corrupt the file at some point.

  And how do you do backups? Time Machine can't help you... it won't work.

  Backup is crucial, especially if you do things apple say not to do... That is to say move your photos or the iphoto library to the TC and try to use direct from there... expect any day to need a resumption of the library.

• Portege R600: SIM inserted but error: "device not found".

  Hello

  Portege R600 under XP.
  Put a SIM card in the slot, but I get the error above: Wireless Manager Toshiba "device not found".

  Cannot find the configuration options or anything like that in the manual.
  Can someone point me in the direction of literature?

  Thank you very much!

  Evan

  Hello

  Here you can download the latest version of 3G driver and tool:
  http://APS2.toshiba-tro.de/WLAN/?page=3gdownloads

  Here you will find a knowledge base on the topic of G 3:
  http://APS2.toshiba-tro.de/WLAN/?page=3ghowto

  and here you can find a HowTo create + how to create a Dial-Up connection with 3 +.
  http://APS2.toshiba-tro.de/KB0/HTD9802OF0000R01.htm

  Hope this helps

• HP Deskjet 3054: Printer works but not the Scanner (device not found)

  Configuration: Windows 8 Lap Top with a HP Deskjet 3054 directly connected via USB

  Printer - it works

  Scanner - when you run the Application "Hp Scan and capture ' it comes back and says"device not found ".

  I tried - I ran 'HP print and scan doctor '.   Everything is OK except the "HP Scan".  He said that it was not able to find the HP Scan software on my computer.   When I went on HP customer support site to download it, I couldn't find it.  There is nothing that I could see which says "HP scanning software".   So this software HP Deskjet full functionality and drivers what I should download and install?

  BTW, the "HP Scan and Capture" application allows to work perfectly.  Not sure why it isn't now.

  Hello

  When changed the type of network to a USB connection? scanning HP and Capture app support network scanners, it does support a USB connected device:

  http://support.HP.com/us-en/document/c03478505

  In the HP Deskjet 3050 software select scan a Document or Photo and check if this can work...

  If the same persists, unplug the USB, uninstall the HP Deskjet 3050 basic software drivers from programs and features, then download and reinstall the most comprehensive software features again.

  If you prefer to continue to use the HP Scan application capture &, open the HP Deskjet 3050 software, click the utilities tab, click the printer installation software & and select Convert USB wireless to connect the printer to your network. then the Scan & Capture app should detect the scanner.

  Shlomi

• Device not found Airport Extreme

  We have an airport extreme connected generation via Ethernet to a switch that provides network access to our entire House (about 10-15 connections) via wifi access points all Ethernet hard wired (linksys + apple) and a direct wire to a PC. Airport extreme is the dhcp and is connected to a gpon fiber using PPPoE.

  The problem now is that the AirPort Extreme disappears from the airport on iOS Mac utility and Windows, it is found however the network and the Internet continues to operate normally on all connected devices. I can also continue ping on the router.

  I have reset the AirPort Extreme to the default settings, but the problem continued...

  I tried to unplug all devices and have AirPort Extreme only connected to him have the fiber but the problem persists...

  no idea how I can fix this problem?

  You describe a known problem with Back to My Mac which first appeared around July 13. The problem manifests itself in a message "Device not found" meant to be displayed in triangular AirPort your AirPort base station with a yellow icon utility, while the router of the device functions others continue to work normally.

  If you use an airport Time Capsule, backups will not work using that device or USB hard drive units connected to it.

  Apple will only be able to solve this problem, so all you can do is wait for them to do. If you want to contact them to tell them about it, using the contact Support link.

  There is a solution: on a Mac, open AirPort Utility and select file > configure other...

  For each of your routers Apple AirPort Base Stations serving their respective networks: its IP address and password (if you don't know either of them, read the Note that follows the horizontal rule below). Then, on the tab of the Basic Station , delete all the entries in the Back to My Mac using the 'negative' button, then click on Update.

  Which must be re-established appearance of this base station in AirPort Utility, as well as in a side bar of the Finder, if all shared disks are plugged on. It will also restore possibility of Time Machine to save on these discs, if this has also been a problem for you.

  If this seems to imply that you will not be able to use Back to My Mac until Apple fixes it, you are probably right. Well to diagnose problems of the CCMM is tedious work that I have not yet finished.

  Apple does not participate on this site except in a very limited way, so don't expect is not a response from them, here or elsewhere for that matter. We'll just have to wait for them to fix it.

• Airport devices not found

  Hello! I have two devices from the airport: on the one hand at home and a time in my lab Capsule. I was away for 20 days and yesterday, when I came back, there was a problem with the two: my Mac cannot access these devices, they can connect to wifi networks hosted by them. When I try to access these devices via Airport utility, I get the error message "device not found". This message, both at home and in the laboratory, tells me that the device was part of my network before, and that I should check if it is within its range. There is an option to 'forget the device' in the end. It is quite strange, as other Mac networking for my laboratory do their backups normally during my absence. Could you please help me? Thank you.

  This was reported once many here recently.

  A 'solution' refers to those who have set up their base stations for Back to My Mac. If you did, how to follow recommended action is temporarily remove or disable this option, as follows:

  • Run the AirPort Utility.
  • Select the base and then station, select change.
    • Note: You may need to use the option "configure others...". "to access the base station. Enter the IP address of the base station, the default value is: 10.0.1.1 and base station administrator password when you are prompted.
  • On the tab of the Base Station, go back to the section of my Mac at the bottom of the window.
  • If you have entries here, select it and click then the minus sign "-" button to remove it.
  • Click on update and allow the base station restart.

• Device not found in airport 6.3.6 utility

  Running a 5th generation I'm stuck. I checked a bunch of other posts and restarted all devices, as well as reset the base station. I also adjusted IPv6 at the local level.

  When I pull up the Airport utility, I get "device not found" and cannot connect to the base station to adjust settings. What is weird is I can get temporarily in Airport utility if restart my MacBook and the base station at the same time. However, it does not last long. I also see the drive mounted in the Finder all the time. A Wi - fi connection works without interruption.

  I tried this on 2 Macbooks, an ipad and an iphone. El Capitan running. I am at a loss.

  Someone at - he was able to solve this problem.

  You are one of the many ad today with this problem.

  for example. There is only one thread.

  Time capsule not recognized in the utility of the AP

  I suggest that you can still access the AE or TC using configure others and type the IP address.

  A 5th generation is the flat and quite old but more reliable than Gen6. But beyond 5 years they get flakey.

  If you mean a 5th Gen TC then this is the newest one.

  I am surprised, he's also missing on the iOS but who was more reliable version of airport utility.

• Office jet 4500 G510-g, the imaging device not found

  I have an Officejet 4500 with a wired Ethernet connection. For some reason any, that my computer has ceased to be able to scan from it, I can still print and everything very well. I don't remember to make changes to the system and other computers on the network can always analyze without any problem. I restarted my computer, unplug the printer, uninstalled and reinstalled the software, active windows firewall settings and cannot find any reason why it won't work. I am running Windows 7 64-bit on the computer that does not work, the other computers on my network that still work are running windows 7 64 bit and XP. On the "HP Imaging device not found" error message that opens under more information, I get this: 8 [(1, 0,-2147221496)]

  I've lived the HPSDU and he said: there is a problem with the driver and he cannot communicate with the product. He said also it is impossible to scan with windows WIA, and finally it's the Twain component may be damaged. I have uninstalled, reinstalled, re-downloaded the Installer off the HP site several times, but can not solve this problem. Help, please.

  Hi crakerb,

  When you click on the plus sign on the error message is that all of the information it provides?

  Because you can not install the printer using the USB connection, it seems to have some problems with the operating system on this computer. Did you back up your data and perform a full system recovery?

• 15 15 HP - r208nl: start the device not found error (3FO)

  Hello

  I have this laptop from less-than-one-year-old (this guy: http://icecat.us/us/p/hp/l0n16ea/laptops-0889296492238-15-r208nl-26524145.html) and I have the Boot Device not found error infamous.

  I'm not sure if this is relevant, but the problem occurred a few weeks after the upgrade to Windows 10 (when bought, laptop had Windows 8.1, probably an update of Windows 7).

  Also, I noticed this basic operation to during the priming phase take a long time. For example, when I press F10, it takes about 1-2 minutes to bring up the BIOS configuration screen.

  There are a number of similar questions on this forum, but the proposed solutions do not apply to my case or simply do not work. Here's what I've tried so far, without success:

  • hard reset
  • reinstalling the hard drive
  • automated tools in the Recovery Manager (this tool you access by pressing F11 at startup) *.
  • chkdsk and identical from the command prompt (to which I have access from the Recovery Manager tool) *.

  Note that even if the material for the HP PC Diagnostics tool failed hard drive test, apparently I can access my files on the hard drive of a Linux Live CD/USB (I managed to access it during a previous attempt, do not know if it can be reproduced).

  I can't test the drive on other PCs (which I have another laptop which I can plug the drive may be defective), not I can try to connect another hard drive non-offending for verification (as I did not).

  Any suggestion?

  They gave me no installation CD/DVD (I guess I had to use the recovery partition). In case I need a new installation, how can I retrieve my serial number?

  the hard drive is not accessible, I can't access Recovery Manager simply by pressing F11, I had to use a USB recovery media

  CHKDSK and even produce this error message: "cannot open volume for direct access.

  It looks like your hard drive is not/is a failure. Guarantee would provide a new replacement - and probably send recovery media free since did you not make it yours.

  You can make a Windows 10 usb or dvd using the free download of Ms. No license key is necessary since it has been activated at the same time on the machine.

  https://www.Microsoft.com/en-us/software-download/Windows10/

  Read the guide here by reinstalling an previously active Windows 10:

  http://www.howtogeek.com/224342/how-to-clean-install-Windows-10/