Time capsule works bur airport utility cannot find it

Similar Questions

• Airport utility cannot find Time Capsule

  Airport utility can't find my Time Capsule.

  I tried to reset (factory settings) several times and then reconfigure TC.

  It works for 2 minutes; the led is green and the TC is visible in AU - but while time Machine is looking for the disc and the preparation of the backup, the disk disappears from the to THE and therefore cannot perform a backup.

  Also, the light is still green after the TC disappears from the AU.

  Could there be a problem with AU?
  Or my TC is all just too old? -I do not know what generation it is, but it's at less than 4 years old, maybe 5.

  I have a MacBook Pro running on El Capitan 2012.

  I hope someone knows how to solve this problem

  Could there be a problem with AU?

  No, Airport utility is very good.

  I have a MacBook Pro running on El Capitan 2012.

  Network problem is common... and it's here... El Capo.

  Or my TC is all just too old? -I do not know what generation it is, but it's at less than 4 years old, maybe 5.

  Possibly in combo with this old CT... What model is the basis... A1xxx?

  Or in Airport utility immediately after a reboot... Hold down the option key and double click on the symbol TC. It will open the summary page with the template at the top.

  Have another go with the installation... See below.

  But tell us what is your provision.

  This modem you... brand / model?

  What the TC set, bridge or router?

  Is the computer connected by ethernet or wireless? Have you tried both?

  Here are my suggestions...

  Start from a factory reset. No files are lost on the drive hard in doing so.

  Universal factory reset

  Turning off the TC... That is, remove the power supply cord or the power at the wall outlet, wait 10 seconds... Hold the reset button... be nice... Turn on always even now in reset... and keep holding in for another 10 seconds. You may need assistance because it is difficult to hold in reset and power on. It will show the success quickly flashing led front. Release reset... and wait a few minutes for the TC to reset and return with the factory settings. If the front LED flashes quickly you missed and simply try again. The reset is quite fragile in these... Press the key while it is just click away and not more... I've seen people bend lever or even break. I use a toothpick as a tool.

  NB. None of your files on the hard drive of the TC are removed... This simply clears the settings of the router of the TC.

  The installer the TC.

  And then redo the configuration of the computer with the Mavericks - Yosemite - ElCapo. (MYELCAP)

  1. the use of very short names... NO APPLE RECOMMENDED names. Without the space and pure alphanumeric characters.

  for example TCgen5 for the base station and the name of the TCwifi wireless.

  If the problem is using wireless TC24ghz and TC5ghz with fixed channels as it also seems to help stop the nonsense. But it can be tried in the second round. IE, plan on a first and second series of changes to fix this... If all goes well... I note other steps can you tour2.

  2. use all passwords also consistent with 1. but maybe a little longer. IE 8 and 20 characters of mixed cases and numbers... no alphanumeric non-caracteres.

  3. If the TC is router, you can ignore this point. It is only a problem when the TC is bridged.

  If ensure that the TC is always the same IP address... you will need to do this on the main router using a dhcp reservation... or a bit more complex setup by using the static IP address in the TC. But it's important for deriving from intellectual property in all directions when MYELCAP do not remember his name for 5 min after a reboot done for poor network management.

  4. check that your share on the computer name does not change... Make sure that it is also in line with the above... short without space and pure alphanumeric... but this change will mess up your TM backup... so be prepared to make a new, full backup. Sorry... keep this one for the second round, if you want to avoid a new backup.

  5 attach the TC disc into the computer manually.

  In Finder, go, connect to the server in the main menu,

  Type in SMB://192.168.0.254 (or whatever ip of TC is that you made static. It's a default router 10.0.1.1 and I encourage people to stick with it unless you know what you're doing).

  You can use the name... SMB://TCgen5.local where you replace TCgen5 with your name of TC... local is the default domain of the TC and does not change.

  However the names are not so easy as... the IP address nor reliable. They are not at least not in Yosemite. The field can also be a problem if you are not clogged or wireless directly to the Treasury Board.

  6. ensure that IPv6 is set to link-local only in the computer. For example wireless open network, wireless and Advanced preferences / TCP/IP... and the difficulty of IPv6. link-local only. Do the same for the ethernet if you use it.

  

  It is a lot more jiggery pokery, you can try, but the above is a good start... If you still find not reliable... don't be surprised.

  You may need to do more work on the computer itself. for example, to reset the NVRAM/PRAM/SMC... helped some people. A clean installation of the operating system is also useful if you update installed.

  https://discussions.Apple.com/message/29202159?ac_cid=ha123456#29202159

  Let us know how you go.

• Airport utility cannot find the time Capsule, but wireless is fine

  All of a sudden my TC stopped taking backups but the wireless works fine.

  Airport utility stopped recognizing the TC suddenly...

  I think it started acting weird it's because last night, I unplugged the TC of the socket directly instead of turn off... This could be the problem.

  This is what, in my view, that the solution could be:

  (1) reboot Macbook

  (2) open Airport utility

  File 3)--> set up

  (4) now he would invite, address and password: especially it would be 10.0.0.1, but you get to the option + wifi

  (5) then just tweak a setting so that the update button is highlighted...

  6) click on update & the router restarts

  (7) Viola you should now see the airport in airport utility.

  I hope this helps. I tried to put that answer in another thread, but the forum has been locked for discussion... That's why this new post

  Thank you

  Bumblebee

  It is not so rosy, as you described!

  I can write in folders on Time Capsule, I use internet, but the utility does not see the drives, printer and Time Machine is no more support for MacBook...

  The only reason for this behavior is dynamic DNS change the LAN iP addresses... after the router has been reset by the network provider.

  Any advice, please?

• Airport utility cannot find Airport extreme

  Using vs 6.3.6 on my Mac Pro. Whenever I run the utility it is something different, but there is always at least one of my extremes that will not be detected. Usually, none are detected the first time I run the utility. If I'm lucky I can restart the utility time 3 or 4 and is ultimately connected to the extreme, I need to access. Sometimes I have to reboot the extreme to access even if it displays a green light. This problem also occurs with the current version of the iOS of the utility and when you try to configure the extreme of OS X Server. Server loses its connection to the extreme router and keep telling me that I used the wrong password.

  Found some old validation recommended setting up IPv6 on my Mac Pro local linc, appears not to have any effect. Someone at - it other solutions?

  Found some old validation recommended setting up IPv6 on my Mac Pro local linc, appears not to have any effect.

  Most users will have more luck if IPv6 on airports parameters are defined for Local link only... unless your ISP provided you with IPv6 specific parameters to use for their service and you have verified that your devices are actually IPv6 addresses.

  Affecting airports Local link may be worth a try if you have not already done this. No guarantee, that the "disappearing airport" bug has been around since version 6.x of AirPort Utility was introduced more than 3 years ago.  Strangely, it seems to be creeping to the right these days.

  

• Time Capsule 802.11ac airport fan is always on

  For two days my Airport Time Capsule 802.11ac 3 TB - Version 7.7.3 fan works verry strong and amber light flashing ist.

  AirPort Utility reports the status "this device could be overheating.

  All functions of the time Capsule works fin (internet LAN/WLAN, hard drives - Time Machine backup)

  Normal temperature just from device ist. Only the fan runs at maximum speed

  When I reboot then TimeCapsule the light is green for a few seconds. The fan works silently. After that, the fan went up to maximum speed and light is orange flashing.

  How can I reduce the speed of the fan?

  The Capsule is defective and needs replacement. Please bring the product to an Apple Store... If you have one near you... or contact the Apple Support directly.

  Contact Apple for support and service - Apple Support

• What is the best way to connect a time capsule from the airport to an existing dsl router?

  I have a Netgear D6300 router with built-in ADSL modem and I'm getting a time capsule from the airport. I thought to put the D6300 in Bridge mode and connect the TC via a ethernet cable but my netgear router is kept in a metal TV armoire or I asked myself if I put on the floor and used to extend my existing wireless which is a little spotty on the floor, but I didn't know if the connection on the hard drive would be too slow. However I read in another post is no longer that apple supports the extension of networks of "no apple"?

  The time Capsule will connect to the Netgear router using a wired Ethernet cable connection, permanent... no matter how you decide to configure things.

  Regarding the location, Time Capsule can be located just about anywhere that it will allow an Ethernet connection. If you want to time Capsule to "extend" the wireless Netgear, and then configure the time Capsule to create a new wireless network that uses the exact same wireless network name and password than the Netgear router. The result will be a network of 'big '.

  Should be a lot more work, but assuming that the Netgear gateway can be configured to work as only a simple modem, the Capsule can be configured as the primary network router.

• ICan I use Time Capsule in my Airport extreme to save files Ihave on my windows7 computer?

  How can I configure my Airport extreme, time capsule 3 to use the portion of the time capsule for the backup of my Sony VAIO computer?

  You can back up a windows computer to Time Capsule but I do not recommend.

  Any backup software that can use target network should work.

  Macrium Reflect is the one I use, I know the Time Capsule works.

  Time line of engineering is a concept similar to Time Machine for PC... It's more that I want to make, but it doesn't seem to be a free version... How good or bad or I do not know what limits.

  Internal backup software MS is generally useless... at least up to win 8.1 10.

  NOTE... A USB connected to the laptop computer and formatted NTFS native is far superior to backup to TC which is formatted HFS + (illegible for windows) which is networked that the SMB protocol and treaded as NT server with all its limitations with FAT32.

  Like many things you answer the question you... Yes. If you have... N °

• The Airport 5.6.1 (10 Windows) utility cannot find Airport Extreme Base Station

  I have the Airport Extreme Base Station (model A1408) model.

  I'm under Apple Airport Utility 5.6.1 on Windows 10.

  10 Windows Firewall is disabled.

  All of my WiFi devices, including my Windows laptop, 10, all work fine on the wireless network, and the light on the base station is green.

  Life seems good... EXCEPT, when I run the utility Apple Airport (version 5.6.1) it says it's "impossible to find wireless Airport". Clicking on Rescan is fixed not. Power by bicycle to the base station doesn't fix it. It worked before, so this is the behavior seems to be somewhat intermittent. Lately, it doesn't quite work. So I can't reconfigure my base station.

  Is this a known issue? Y at - it a known solution?

  First of all, understand that the AirPort for Windows utility has not been updated since Windows 7. It 'works' on later versions of Windows, including Windows 10, but is not designed to work with the new 802.11ac base stations.

  We'll see if this utility is installed correctly on your computer.

  For Windows 8, 8.1, or 10, AirPort for Windows utility will work have two applications listed in the window Apps & features: 1) airport & 2) Hello.

  • Move or delete the file next to the C:\Windows\System32 folder: c:\windows\system32\dnssd.dll (Note: this is the Client Hello library and is required by the utility AirPort.) If this file is missing would be the main reason that you aren't able to find the base station. However, even if it is present, it cannot be properly registered in the Windows registry. In other words, Windows is concerned, there is no.)
  • Download AirPort for Windows install.
  • Run the Setup program by using privileges "Run as administrator". (Note: If you have the option to repair or uninstall, choose the option to uninstall.) To complete the uninstall process. The Hello application should now be missing in Apps & features list.)
  • If you do not dialogue to repair/Uninstall window, then let Setup install AirPort for Windows in its default folder.

  Then, make sure your computer cable or wireless network adapter is configured for IPv6.

  Now, try to access the base station with the utility again.

• My old Airport Extreme 802.11n will work well with my new Time Capsule 802.11ac airport?

  I got a new 802.11ac 3 TB time capsule and I would use my Airport Extreme 802.11n as an Extender but I fear that 802.11n is too old technology.

  No, it will be fine. I have the same setup on my network. Whenever I update my AirPort Extreme, I use the 'old' to expand the network throughout the House.

  I hope that answers your question.

  Best regards

  Austin

• OfficeJet Pro 8600 Plus: HP Utility cannot find wireless Officejet Pro 8600 Plus

  My Officejet Pro 8600 is connected to my wireless network, has obtained an IP address.

  However, I cannot find the printer in the HP utility and cannot connect, even if I try to manually enter the IP address.

  It works fine on the wireless network, recently, he stopped. (I print not that often, so I don't know what changes occurred sinnce the last time I printed)

  I deleted all of the HP software and drivers, downlaoded the latest version and re-installed them.

  I reset the network connection on the printer.

  Operating system is OS X 10.10.5, everything up to date.

  Printer by USB works fine.

  Hello

  Try to reboot your router by unplugging its power for a while and wait a minute or two.

  Then restart the printer and your Mac and try to print.

  If it persists, has what distance is the printer of your router?

  You see the blue light on wireless?

  By pressing the icon on the printer wireless, can you access the IP address listed from your Mac?

• Problems of ' 09 Time Capsule to the Airport Extreme upgrade

  I with success the setup a new Airport Extreme (AE) and I want to continue to use my Time Capsule (TC) 2009 as a backup drive. However, I have questions. What is the right way to implement these devices to play nice?

  I have currently the modem ethernet fall on the AE WAN ethernet. Then I have another ethernet cable connecting the AE LAN ethernet in the TC WAN.

  In addition, I have the TC Network Mode as 'OFF' and his router Mode as 'Off (Bridge Mode).

  Is everything is OK?

  All correct so far.  Also check the Internet tab to ensure that the TC is to connect using DHCP = AirPort Utility.

  

  At this point, what other problems are live you?

• Problem of Time Capsule Roaming Network airport

  I'm having a problem by establishing a network of roaming.  When I plug my extender devices in ethernet cables through a switch to my Time Capsule base station, my wifi signal drops 150 + MBS next to the base station to < 10 mbs.

  I have a wifi in my home network based on a new time Capsule airport base station (ATCBS) running firmware c. 7.7.7.  I have my 4th gen AEBS & a 2nd gen Airport express both race v. 7.6.7 updated firmware in place in Bridge mode to extend my network in different rooms in my house. The system works very well, but I wanted to increase the power of the signal in remote places so decided I would like to convert it to a mobile network by installing ethernet cables to connect my ATCBS the AEBS and express extensions.  I use a switch Netgear 5 port (NOT of GS205-100) that I only have a single LAN fanless available left port on my ATCBS.

  I installed 3 ethernet lines-1 each in rooms with my ATCBS and airport express using mounting wall punch down taken using the convention of wiring 568B, AEBS.  These lines all end with male plugs in a unique space in the basement and are also wired as 568B.  Then I plug the ATCBS, AEBS and express lines in the switch in this remote area.

  I've done a few connection cables in the role of Cat 6 cable, I had over the House, and they all very well with my cable Tester check so I know the cable itself is not defective.  The cables all run in the basement where I can see, so I know there is not any problem to be crimped/damaged.  I have not any gear to test the installed well son.  I visually inspected the male and female (punchdown) ends to ensure that colors are properly prepared.  I did a test of my jacks punchdown conductivity by testing 8 wires on the sides of the socket and the pins in gold on the inside where an ethernet cable connecting between the cut ends.  All wires are correctly leads to the appropriate pins.

  If I plug just the ATCBS into the switch next to him and using a good patch cable I see no change in the strength of the Wifi.  If I can plug my express (also moved to the room of the base station) using another cable good patch in the switch, wifi drops as described above.  If I plug the ATCBS on the new socket and the switch at the other end - no change in force wifi.  If I plug the express in its remote location system also uses the new ethernet cable installed for him and passing through the switch, I get the wifi signal reduction.  I get the same result if I take the express up to thevbasemenbt and plulg the switch with a connecting cable).  It seems therefore that the problem may not be with the newly installed cables that I get the same result by using or by using cables good patch, and with the switch in the same room with the ACTBS.  It doesn't matter how I'm trying to connect all the devices together, plug extender devices into the system brings the WiFi falling to almost nothing.

  Any ideas on what could happen?

  I'm having a problem by establishing a network of roaming.  When I plug my extender devices in ethernet cables through a switch to my Time Capsule base station, my wifi signal drops 150 + MBS next to the base station to < 10 mbs.

  That's what happens when you initially set up the device to the airport "extend" using a wireless signal... and then later connect an Ethernet cable to the unit of the airport.

  Since the airport is configured to connect wireless and waiting for a wireless connection, the Ethernet connection and then creates a feedback loop massive on the entire network... in fact, basically crashed the network.

  Basically, you have to start over again with the AEBS and AirPort Express and "Apple Installation Wizard" to set things upward. It's practically automatic. All you need to do is assign a device name to each airport and the wizard supports all the rest.

  After the back if you need some advice on how to correctly configure things.  You can be amazed at how simple, it comes... and surprised by the wizard settings apply.

• AirPort utility cannot connect

  I have an Airport Extreme base station which is about a year.  I have several devices connected to the internet via laptop from Samsung, I type this question with this router.  If I run AirPort (windows) v5.6.1 utility he finds the base station (says it's the 7.7.3 version if it's helpful).  When I select 'continue' to try to change the settings, it says it is reading from the device and then gives an error message "an error has occurred while trying to access the device wireless to Apple."  Make sure your network connection is valid and try again. "There are a number of error 10057.  Notable, that he never asks the device password.

  Also, I tried to use the utility AirPort 6.3.2 MacBook Pro from my wife.  With this device, I tried to connect via ethernet cable and wireless.  He sees not the device--even if it is not connected to the internet.

  I rebooted the computer and the router, and the behavior does not change.

  Any thoughts on how to proceed?

  You must reset the Airport Extreme.

  Someone might have the installation program the device to lock... changes accidentally even.

  I recommend you first do a soft reset.

  Press the reset for just 1-2 sec... button the front led will flash amber... This allows you to 5 min of access without security and change all passwords at the factory. That is to say the password main AE will return to the public.

  See if you can access it for 5 min, then make the changes you need.

  Otherwise you need a full factory reset.

  The danger with that is you lose your internet connection and then can't get it back.

  Universal factory reset

  Powering down of EI... That is, remove the power supply cord or the power at the wall outlet, wait 10 seconds... Hold the reset button... be nice... Turn on always even now in reset... and keep holding in for another 10 seconds. You may need assistance because it is difficult to hold in reset and power on. It will show the success quickly flashing led front. Release reset... and wait a few minutes for the TC to reset and return with the factory settings. If the front LED flashes quickly you missed and simply try again. The reset is quite fragile in these... Press the key while it is just click away and not more... I've seen people bend lever or even break. I use a toothpick as a tool.

  I'm a little surprised that you can't access the extreme via the Mac well.

• SB6141 and Time Capsule works best not Modem?

  I bought an ARRIS / Motorola SB6141 modem yesterday, unfortunately without checking here first of all support and as much I having trouble to get a SB6141 and Time Capsule to cooperate.  The modem works fine with a hard line, but when I plugged in my Time Capsule for the modem I got the dreaded flashing yellow on the TC light. Three hours of reading posts here (and elsewhere) and troubleshooting later and I am still at a loss. Rather than the fight over trying to get the SB6141 to work, I would rather just buy a modem that works (at least mostly) with the TC. I am in the area of Chicago on Comcast. List of approved here modems. Please let me know if you have found a good modem to use with time Capsule. Thanks for any help!

  Additional details - I bought time Capsule 2 TB in March this year and it's all so far (ongoing enforcement, I think, 7.7.3)

  Not on Comcast, but the use of two modems in rotation.

  Zoom 5341J and Netgear CMD31T, who all have both been impeccable since they went into service almost 2 years ago.

• How can I fix my msconfig so that the system will work? error: "Windows cannot find 'msconfig'.

  When I go into run and type msconfig, I get the following message.

  "Windows cannot find 'msconfig'. Make sure you typed the name correctly and then try again. to search for a file, click the Start button, and then click search. »

  Only three names came when I ran the search.
  1. msconfig in C:\WINDOWS\Help
  2. MSCONFIG. EXE in C:\WINDOWS\Prefetch
  3 msconfig in C:\WINDOWS\pchealth\helpctr\binaries

  Hello

  Thank you for writing to Microsoft Communities. I understand that you are unable to open msconfig on the computer.

  I understand how it could be frustrating when things do not work as expected. Please, I beg you, don't worry I'll try my best to resolve the issue.

  1. what operating system is installed on your computer?

  2. have there been recent changes to the computer before the show?

   

  Please go ahead and follow the steps mentioned and later a update on the State of the question.

  Method 1: Rof the United Nations [System File Checker] SFC scan on the computer that would be a search for system files corrupted on the computer and replace them.

  For Windows 7 and Vista: http://support.Microsoft.com/kb/929833

  For Windows XP: http://support.Microsoft.com/kb/310747

  Method 2:  Also try to scan your computer for the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Please follow these recommended steps and post if you still experience the problem.