Time GPS, Position, Velocity.vi - error-1073807360 reading was held at node (arg 1) .vi property VISA set up a Serial Port (Instr)

Similar Questions

• error of node (arg 1) .vi property VISA set up a Serial Port (Instr)

  Hi all

  I have a request, he had run on a machine well for months.  I use VISA to make the communication between PC and PIC.

  Suddenly at certain times, it reports error of node (arg 1) VISA property set up a Serial Port (Instr) .vi. Since then, it does not work.

  Œuvres of HyperTerminal.  I check MAX, the COM port it and looks very good.  What is the problem?

  Furthermore, I use VISA 4.2.  Maybe somehow it crashed?

  Many thanks for any help.

  Problem solved.

  The reason is that the hard disk was running out of space and there is error.  Somehow, causing accident DURATION VISA.

  We cleaned drive C: for free space and then repaired DURATION VISA.  Now, he runs with happiness.

  Thank you, everyone, for your help.

  

• Error: The property node (arg 1) in .vi VISA set up a Serial Port (Instr)

  Hello

  I've seen people once they have gotten this error, but none of them really apply to my situation.

  Right now I use LabVIEW example code to read from a device manufacturer. This device is connected using a Tripp Lite USB adapter series (http://www.tripplite.com/en/products/model.cfm?txtSeriesID=782&txtModelID=2430) for the connection from the PC to device with RS232. The adapter works fine when using the software prepared in advance (not LabVIEW) given by the manufacturer and the COM port is seen by LabVIEW. When I run the program, I get the property node (arg 1) visa set up a Serial Port (Instr) .vi (I've also attached the VI but it's a standard VI I got of LabVIEW). I get this error despite the fact that I use the same COM port, who has worked with the manufacturer's software.

  I have attached manual of Protocol RS232/debit BUS (not sure if this applies) that requires the device. The device is a mass flow controller whose operating instructions is: (http://nemu.web.psi.ch/doc/manuals/device_manuals/Bronkhorst/917023--Operation%20instructions%20digi...

  I'm using LabVIEW 10.0.1

  Any help is appreciated

  Try to restart the PC and then try the LV version before trying other software.

  I have seen thrid party serial interfaces work on the first try but fail when you switch to another application. It was as if the pilot did not know that it was no longer the first process.

  Ben

• Error: The property node (arg 8) visa to configure the Serial Port

  I'm trying to control 8 USB to R232 via a HUB of 10 ports Tripp-Lite (model U222-010-R) and do not have consistent results.  Just after rebooting my computer, I have no problem in running the following program: (I tried to download the VI directly but without success, so here's the extract)

  

  I made sure that the COM ports that I select are that one is available on both the Device Manager and in the NOT-MAX.  But after awhile, it does not work or if the HUB is unplugged and replugged in (even if the names are correct and up-to-date in devices and NOR-MAX Manager) I get the error code "property Node (arg 8) visa set up a Serial Port (Instr) .vi" I want to be able to see these ports consistantly more without having to restart my computer all the time.  Is there a better Setup for this? The previous installation of the computer has a PCI card for it and we have not had any problems with the code, but are facing problems with our upgrade.  The old computer ran Windows XP and had cards PCI and the new computer that I am using a Windows 8 and the USB HUB.  Thanks for any help you can give!

  Mr says:

  Jeff,

  It is a one off lines from specifications Tripp-lite:

  -On bus power, 500mA from the USB 2.0 computer port is shared between hub ports

  This would be in support of what I need or not necessarily?

  -Mr

  No! That's the 50mA by port not 500mA.  an order of magnitude full powered USB (if you want reliable - if you want real problems which appears irratically each time only and is a headache to track down which would)

• Log time GPS, position, speed

  Hello

  I use the read time gps, position, velocity.vi and now I want to save this data in a text file or a spreadsheet. Is there a simple way to do this? I tried with write in the file of the measurement, but this handles dynamic data and no stamp string or time.

  Thank you

  

• I am not able to connect to my facebook account and the error message reads "this website does not provide information on property." Help, please

  I am not able to connect to my facebook account and the error message reads "this website does not provide information on property." Help, please

  only title bar opens and nothing else... Please help

  Clear the cache and cookies from sites that cause problems.

  "Clear the Cache":

  • Tools > Options > advanced > network > storage (Cache) offline: 'clear now '.

  'Delete Cookies' sites causing problems:

  • Tools > Options > privacy > Cookies: "show the Cookies".

  Also check the cookie exceptions.

• When you start 5 Lirghtroom I get the following error message every time: "Lightroom has encountered an error when reading the preview cache and needs to stop smoking.  Lightroom will attempt to solve this problem, the next time it starts. "He never start

  Title says it all.  Lightroom stops because he can't read in its cache of the preview.

  Take a look at this topic, there is a solution.

  I get an error message when I open Lightroom

• I can't connect to the other user account... error message read s 'user name' or password. We have not set up a password and user name is correct.

  I can not access another user account.  It to request a username and password.  I enter the user name is correct and there is no password.  The login page, used to have two icons of the user; but for some reason, the last log on the user icon is here and a new white icon for the new user.

  Once a week a few posters noted a problem similar to yours. In this case, I post the answer you see below. The little that I find very irritating that in each case, without exception, the poster was not able to return and account for the results, either because they found my recipe too difficult to follow, or because he or she lost interest, he or she could not be bothered to post a few comments for the benefit of other people with the same problem. There it is again...

  I do not know why you can not change this password, but maybe this method will shed light on the question:

  1. Safe boot mode.
  2. Click Start.
  3. Type the three letters cmd into the search box.
  4. Press Ctrl + Shift + Enter
  5. Click on "Run as Administrator".
  6. Type the following commands and press ENTER after each one:
     'John Doe' ppp NET user / add
     (to create an account called "John Doe" with the ppp password)
     net localgroup administrators/add "John Doe"
     (to promote "John Doe" to the Administrators group)
     net localgroup administrators/del 'John Doe'
     (to demote this account)
     NET user "John Doe" ppp
     (to set the password for John Doe at ppp)
     NET user "John Doe" / active: Yes
     (to activate this account)
     NET user "John Doe" / active: No.
     (to disable this account)
     NET user "John Doe" / del
     (do not delete this account)
     NET user
     (to view all existing account names)

• Problem: read bytes to serial port

  Hello, I need to communicate with an external device with serial port. I have to write a command to my device string, and then it should play with 64 bytes of data. I built a function of READING-WRITING and I use it in a loop (I have to read a lot of 64-byte block)

  Sometimes, I have the following problem:

  (1) I have send the command string, I wait with "Bytes to the serial port" whereas I have more then 60 bytes, then I read.

  (2) sometimes happen that the read function cannot read all 64 bytes, so the net for cycle, I have in the receiver buffer mor than 64 and the program to stop working. (does not work well)

  I need to be sure that after writing the command I have 64 bytes, so I red all the 64 bytes so the next loop for, I have the buffer of the empty receiver.

  I enclose my writing reading function. Please refer to the block diagram (there are a few notes).

  Thank you

  In no place in your program see the VISA configure the Serial Port. It's always a good idea to include this that even if you use the default settings. I suspect this is one of the default settings which is wrong with you. By default, playback is set to end when a character is considered. This means that if you have a 10 hex (ASCII LF) in your stream, playback stops until the specified number of bytes is read. Put in a VISA set up the Serial Port and connect a constant False to the stop character allow entry.

• Hi, I have a Lightroom on PC 5.  I read it has encountered an error while reading the cache memory and must leave the preview.  I put off my computer several times and try several times to open lightroom.  But no success!

  Hello

  I have lightroom 5 on PC.

  I read it has encountered an error while reading excerpts from the story of cache and must leave the preview.

  I have put off several times my computer and try to open several times lightroom but not success.

  Thank you

  Delete the folder named child Previews.LRDATA shooting. Do not remove anything else.

  There is a button to translate each message, you can use it to translate into French.

• Trying to open the message box appears 'lightroom has encountered an error when reading the preview cache and needs to stop smoking' Lightroom "Lightroom will try to solve this problem, the next time that it launches" OK when you press closed Lightroom an

  Trying to open 5 Lightroom, a message appears 'Lightroom has encountered an error when reading the preview cache and needs to quit' "Lightroom will attempt to solve this problem, the next time he throws" when OK key Lightroom quit unexpectedly and the computer returns to the office.  This persisted for 2 days and it has not set itself.  help please.

  Click OK close Lightroom.

  You must manually go to the location of your Lightroom by Finder catalogue / file Explorer and get rid of the Previews.lrdata folder

  By default, the location would be in Pictures\Lightroom folder

• Download other store apps that require a GPS location leads to error messages.

  Original title: Maps
  My position has stopped working over the weekend. Download other store apps that require a GPS location leads to error messages. What have I done?

  Hello

  -What are the error messages that you receive when you download apps? (This will help us find the cause of the problem)

  We will check your zone settings, if they are configured incorrectly to correct us and check if this solves the problem.

  a. on the start screen, enter the Date, press or click settingsand then press or click on define the date and.

  b. the Date and time tab, tap or click on change of time zone.

  c. check if the zone settings are right depending on your region. If you find not bad, change it accordingly and click on apply, Ok.

  Also to synchronize the time on the computer with Internet server by using the step below:

  a. on the Internet time tab, tap or click on change settings.

  b. check the box synchronize with a time server Internet and then tap or click Update now.

  Restart the computer and check that it works very well. If you experience additional problems, you can reply to this post.

• Parity errors & read on Serial Port framing

  Hello, I am writing a program that reads the serial port IR thermometer. Intermittently I get parity so many framing errors and can't explain why or find a way to remedy. All the parameters of the series were double checked and controlled. I don't get any errors when you use HyperTerminal yet, when I do test bed in MAX, I see these mistakes from time to time. I tried the suggestions of the knowledge base for these as presenting a delay between the Visa set up and read the Visa or flushing buffer issue before reading, but none worked. Any idea or ideas would be appreciated.

  In addition, while searching through discussions on parity and framing errors, I saw a when a user recommends the following: "use wait event triggered by the stop character and when the error occurs, I just deleted the error, empty the buffer (wait the next stop character) and reread." If that sounds like a good solution, how would I go about its implementation?

  I've attached a screenshot of my reading series loop so you can see what I'm doing. I do about the error code control timeout is.

  Given that you have activated the stop character, you should not use the bytes to the serial port. You shouldn't have to delay or any function buffer flush.

  PS, You also have to change the way your loop exits.

• 'Lightroom encountered and error while reading its preview cache and needs to stop smoking' I have LIghtroom 3 catalog Previews.Irdata; should I remove all three files?

  I get this error several times when I use Lightroom. "Lightroom encountered and error while reading its preview cache and needs to stop smoking" tells me to remove the preview folder.

  I have LIghtroom 3 catalog Previews.Irdata; should I remove all three files?

  LAR

  

  Simply remove the Previews.LRDATA folder that bears the name in the catalog file, you are trying to open.

• Cannot start/open new Premiere Pro trial - error flag reading - on demand could not start properly _ 0c000001d click OK to close the application

  Dear Forums

  Cannot start/open new Premiere Pro trial - error flag reading - on demand could not start properly _ 0c000001d click OK to close the application

  * Also, I sent my first question 20 minutes ago, not yet approved? Your return indicated "approved" e-mail, * why do I not see my question below still displayed? >

  The members of the Forum Pro first - Hello
  

  
  

  Can someone out there describe in simple basic procedure, how a first time user start using Premiere Pro to the layer just a moving figure video of 5 minutes (a friend aerial artist model with white moving belt in silk on a rest mainly black background layer and a change to a night sky stars panorama I photographed previously?)

  I know that this can easily be done, I have worked in thousands of still images with creative cloud for previous years, but not yet in video in Premiere Pro, so thanks for any advice.

  I enclose the actual video that I use and some samples of the fields of the night sky that I photographed recently for ideas

  I intend to make possibly more elaborate, but for now if anyone of you could just show the basic commands and menus/menus to start to do it simply and quickly. Maybe how to most later convert it tone black & white or sepia. The ideas here is to recreate a sequence modern suite of familiar German Film, wings of desire. Perhaps also a progression in the future to create an effect of the night sky very slowly turning into one layer background behind the main façade first video layer in normal movement. Then maybe a little further - how to adjust the speed of the front to a path layer more slow half price while keeping the substantive motion, the original speed. (* although I realize that I didn't do in 64 fps for the slow movement, I am not concerned about that and would actually welcome a light old world "flip effect framework" as if, in appearance of the films more former silent motion.) * In addition, possibly cutting on 'dead time' a few seconds at the beginning of the video and the 2nd or 3rd time for a few seconds of this unexpected error, when the silk scarf fell on the camera lens (without changing the audio timeline?)

  * (I use Windows 7 on a Toshiba Satellite L555 - [only RAM 4 MB. rates], 2009)

  * Video sample >

  Sarah Seiler Aerial - camera Check-An Unedited manifesto-Dec 16 2015 - YouTube

  * Background samples >

  w-left-west-frames-with-earlier_sept-8_9-2015_1_stitch-mercator-projection-2a-titles-5000-pxl-b_galaxies-at-right-enlarged-5500-pxl http://www.dpreview.com/galleries/1579463287/photos/3374478/Trillium-Lake-Aurora-add-26-ne

  Comet Lovejoy Andromeda brand camera telescope DSC3857-1a-blue-light-increase-layer-Nov 20 2015: Mark Seibold: Galler...

  Larch Mtn Night Sky Sony NEX5R 5 Oct 2015_panorama point 2 b side of cropped rt 3000 pxl: Mark Seibold: galleries: digital...

  Cannon Beach Haystack Rock mamiya 55mm 25 2015_10_stitch_102 26 Aug frames Projection of Mercator Crop dark as he nu Fi...

  Trillium Lake Mount Hood Dark Night Sky Nov 10 2014_stitch a 5000 pxl f to fill 2: Mark Seibold: galleries: Digital P....

  Thanks so much for all the advice of one of you in the Adobe Premiere Pro forums,

  Mark E. Seibold, artist-astronomer, Portland Oregon

  Duplicate thread here: may describe in the simple basic procedure, how a first time user start using Premiere Pro to the layer just a moving figure video of 5 minutes (a model friend artist air with white passage belt mainly black silk )

  Thank you

  Regalo