Timer on the watch

Similar Questions

• Can I connect the watch or Bluetooth headset at the same time?

  The watch or Bluetooth headset (maybe a pair of the Airpod) connect at the same time?

  I have iPhone 6 now and will update to 7 earlier.

  I do it all the time with my iPhone 6. I assume you mean to plug the headphones into the iPhone, right? Whatever it is, you can connect to the phone or watch.

• get the world out of the watch dial time

  I use the standard watch face, but a time for Las Vegas keeps appearing at the top of the watch in small print.  I can't change that too, a city actually, I care.  I made changes in the Word timer on my watch and my iPhone, I even remove the cities of weather, there is no way I can make it disappear or (what I want) change in another city.  I would like to see a second time of cities, but I can't seem to change

  Try these steps

  1. on the phone

  Go to the clock of the world

  Put in the cities you want to

  2 force to restart the phone and watch

  Restart your Apple Watch - Apple Support

  Restart your iPhone, iPad or iPod touch - Apple Support

  3. try to change the city on the dial of the watch using the method to customize as usual

  The city you entered in the phone should now be available to take

• How to watch two clips at the same time on the other, with an opacity of 50% each.

  How to watch two clips at the same time on the other, with an opacity of 50% each. It is confirmed that the position of the object even two clips of mergers.

  Thank you

  PPut a clip on top of another in the timeline panel. In the video Inspector reduce the opacity of the clip on top.

• My locks of Apple Watch every time that the screen turns off.

  From the past week, whenever my screen goes black on the Apple Watch, it crashes. Whenever I want to check messages, use siri or do anything outside the eye at the moment, so I have to unlock it with my access code. It's pretty boring.

  Hello

  Check your settings.

  • On your iPhone, in the application of the watch, go to: My Watch (tab) > General > enable the detection of wrist.
  • On your iPhone, in the application of the watch, go to: Watch My > General > screen Wake > turn the Wake screen on wrist lift.

  Also, make sure you wear your watch sufficiently well adjusted. If worn too loosely, your watch may believe that he had been removed from your wrist. With access code also allowed, it would then automatically locks. Performance of the sensor can also be affected by temporary changes or permanent on your skin, such as certain wrist tattoos.

  

  If you have not already done so, it can help to upgrade your iPhone and look at the latest version of the software, from your iPhone:

  • Update the software on your iPhone, iPad or iPod touch - Apple Support iOS
  • Update the software on your Apple Watch - Apple Support

  More information:

  Port Apple Watch - Apple Support

  https://help.Apple.com/watch/#/apd748b87e2a

• How to display the number of steps on the dial of the watch

  I so enjoyed my Fitbit wanted an Apple Watch, but may not know how to get the steps, heart rate, etc., on the dial of the watch so I don't have tro go in applications every time.  Any thoughts?

  Thank you very much!  I think I can do this :)

  Really useful.

  Jan

• How to put in the front of the watch during swimming to see heart rate

  Received the Watch 2 day and taken for a swim practice in the pool (of course)

  happly to see enough faithfully has towers and gives average heart rate but only AFTER training

  I wanted to 4000 m (and I fact..) but from the exercise the watch when asked for the total calories to burn.

  QUESTION 1: how to set the distance (rather than calories)? At the start of the year?

  While the dial of the watch training appeared when out of the water and gave the number of laps, total distance, total time of exercise and calories burned.

  QUESTION 2: you can change the information presented during the swim to see heart rate? (Rather than the number of Calories predictable)?

  NOTE

  For swimming training, the watch is a bit disappointing, given that in the swimming training, you normally do a few repetitions as 10 x 100 start each 01:30 or 01:45. I normally use the watch of Garmin swimming to take the time (100 m start button and press again on arrival) of the clock, then briefly shows duration of the tour and afte 4 continuous seconds so you can see when you start again (e.g. to 01:45). I hope that there will be a third-party solution soon for Apple Watch 2, while I don't have to swim with two watches...

  Hello

  1. After selecting the length of the pool, slide laterally on the screen to move to a distance goal, which can be set in meters or yards (firmly press the screen to switch between them).

  2. follow the following steps to customize the information displayed by the application of training during your workouts in the pool swimming:

  • On your iPhone, in the application of the watch, go to: Watch My > training > training view.
  • Choose several metrics.
  • Tap pool swim > press on edit (top-right) > select up to 5 parameters, including heart rate (they can be arranged in your order of preference).
  • When you are finished, tap on Done (top right).

  More information:

  Work with your Apple Watch - Apple Support

• Apple Watch sport does not work correctly. The display is 'crazy' once or twice a week and I need to force restart it. Do you know what is happening with the watch? Is this a common failure?

  Apple Watch isn't working properly. The display is to be 'crazy' once or twice a week. And I need to force restart it. Is this a common failure?

  Hello

  This isn't a failure or defect.

  Zoom (an accessibility function) has been activated on your watch and you are zoomed accidentally tapping on the screen in a particular way.

  • To turn off the Zoom:
    • On your iPhone, in the application of the watch, go to: My Watch (tab) > general > accessibility > Zoom - put it off.
    • Or on your watch, go to: homescreen (via a simple press on the digital Crown) > (cog icon) settings > general > accessibility > Zoom - tap and enable / disable.
  • If the accessibility shortcut has been enabled and configured for the Zoom, you can also enable and disable functionality more conveniently:
    • On your watch: quickly press the digital Crown (the round button) three times.
  • To set up accessibility shortcuts:
    • On your iPhone, in the application of the watch, go to: Watch My > general > accessibility > accessibility shortcut (bottom) > select / deselect Zoom.

• You can swim or shower with the watch

  You can swim or shower with the watch?

  Hello

  Non - Apple advises that you perform one of the people.

  Apple Watch is splash and resistant to water, but it is not waterproof. You can, for example, wear and use Apple Watch during the year, in the rain and all washing their hands. Overwhelming Apple Watch, however, is not recommended. The watch must also be dry if it is wet.

  Apple advises specifically, for example, the following can affect Apple Watch water resistance and should be avoided:

  • Exposing Apple Watch into water under pressure, including under the shower.
  • Swim or bathe with Apple Watch.
  • Overwhelming Apple Watch in water for long periods of time.
  • Apple Watch port in the sauna or the hammam room.

  Water resistance is not a permanent state, and Apple Watch cannot be rechecked or closed for resistance to water.

  More information:

  On the resistance to water Apple Watch - Apple Support

• Shows + 1 hour at the time of the iPhone

  Hello

  After updated to watch OS 2.2.2 when the watch is + 1 hour time of the iPhone.

  Thank you

  Eldar

  Hello

  The following steps may help:

  • Check that Bluetooth and Wi - Fi are activated on your iPhone:
    • iPhone: settings > Bluetooth - on.
    • iPhone: settings > Wi - Fi - on.
  • Check that your iPhone and Apple Watch are connected:
    • When you display the time on your watch, drag upward on your watch dial > drag left / right for the look of settings > check it shows connected and shows a green phone icon. Disable airplane Mode if it is enabled.
  • Restart your iPhone and your watch:
    • Close the two devices together, and then restart your iPhone first.
      • To turn off your watch: press and hold the button side until you see the cursor off the power; slide it to turn off;
      • To reactivate: press and hold the side button until you see the Apple logo.

• Weird things on the screen and the watch does not load

  can someone tell me what this means and how to fix it? Was given on the charger for hours, can not, have you tried the new wall charger and no difference

  Your watch is probably too warm. Keep it in a cool room to let it cool down. The third screen is a warning of the temperature.

  Try to load again, after that the watch is cool.  If you are using a case, keep it open.

  https://help.Apple.com/watch/#/apdcf2ff54e9

  For operating temperature requirements, see this page: Keep Apple Watch in temperatures acceptable - operation Apple Support

  Apple Watch is designed to work best with a temperature of 32 ° to 95 ° F (0 ° and 35 ° C) and must be kept between the ambient of-4 ° and 113 ° F (-20 ° to 45 ° C) temperatures.

  For example, Apple Watch should not remain unattended in direct sunlight for long periods, undergoes large changes in temperature or humidity, or be left in a car on hot days. Store and use your device outside the recommended temperature range may shorten battery life or cause other damage.

  Learn more about the management of the temperature for Apple Watch

  If necessary, Apple Watch will regulate its internal temperature. There are several things you might notice if this happens:

  • Charging time may increase, or load could stop
  • The display may dim
  • A temperature warning screen may appear
  • Data transfers could interrupt or slow down the
  • Apps could close

  If your Apple Watch has above normal temperatures:

  1. If you wear your device, turn the power off and remove it from your wrist.
     If your Apple Watch is charging, remove the charger.
  2. Move your Apple Watch to a cooler place and let it cool completely before you put it back on or to continue to load.

• Size of the photo from the front of the watch

  I did experiment with the use of a photo for a watch dial. While I'm not thrilled there is no way to do any customization of complication with a created face, I tried to find the best size for the photo so I can display as much of it as possible on the face.

  Has anyone experiences no more can I have, since I got my watch for a month to see what photo size must be in order to fully have it displays on the dial of the watch? I'm not looking for something with the small detail, but if I wanted to post the picture of my dog, for example, if I wanted to see his face or his entire body, what pixel dimensions should I use? I created a special folder to save these pictures to and synchronization directly on the watch/phone.

  Hi Chris

  It is not necessary to manually resize a photo for dimensions in pixels used by Apple Watch.

  Instead, in order to ensure that your facial features of watch picture your favorite content posted in its entirety, you can use a photo with an aspect ratio of 4:5. Pan and zoom that you like, then synchronize with your watch. The image will be resized automatically (in terms of pixels).

  For example, when you add a photo of your iPhone:

  • When you use a photo portrait:
    • Press Edit (top-right).
    • Select the crop tool, and then choose the option for the 4:5 crops (Apple Watch screen ratio).
    • Pan and zoom to position the image as you want it to appear on the dial, keeping in mind that the watch displays time in the upper quarter right the watch face.
    • Type actually.
    • Add the photo to the watch via your sync Album (it will be resized automatically on your watch in terms of pixels, while keeping all of the content you have selected).
    • Select the photo to use as a dial of the Photo.
  • If starting with a photo in format landscape, firstly of cultures in a portrait format before you follow the same steps (as the ratio 4:5 crops option is not otherwise available).

  More information:

  http://help.Apple.com/iPhone/9/#/iph96b1e322

  http://www.CultofMac.com/390111/Prep-photos-perfectly-for-your-custom-Apple-WATC h-face.

• Reset the watch due to the error of access code; now, it won't pair with phone

  Last night the watch worked very well and I put it on the charger. When I took it off the coast, he said the password was wrong and I had to re - activate the password of my phone from Apple. I went to my Apple Phone and tried to do and I got up a pop box saying the Watch has been locked and I had to unlock it.

  I tried to unlock the watch since the phone several times, but he wouldn't let me go beyond the box pop up.  I decided that I had to reset the watch, I went to my phone and selected the option cancel the twinning of the watch from the phone. I thought it was non-paired, I could set up the watch again.

  I did and now my watch is dead.   There is nothing on the watch.  It seems masoned. The watch is ruined?

  Help, please!

  Hello

  Try restarting your watch force: press and hold the side button and the digital Crown for about 10 seconds, until you see the Apple logo, then release them and expect the watch again.

• My Apple Watch will not charge on the charger.  I cleaned the back of the watch and the charger.  Any ideas?

  My Apple Watch will not charge on the charger.  I tried to clean the back of the watch and the charger more used several points of sale, but in vain.  Any ideas?

  Hello

  When you reload your watch, check that:

  • All the plastic film was removed from both ends and both sides of the cable support (consult closely on the head of the charger).

  

  • On the back of your watch and the head of the charge cable are clean and dry (clean with an abrasive, lint cloth).
  • The head of the load is properly aligned with the back of the watch, with the concave side / curve touch fully:
    • Some docks of watch, brackets, cases or protectors might hinder it.
  • You use a real Apple magnetic Charging Cable or a certified Apple module magnetic charge.
  • If you reload your watch by plugging into a power outlet:
    • Check that the magnetic charge cable Apple USB connector is fully engaged in the USB power adapter.
    • Try to use different maps of the following:
      • The real Apple USB Power Adapter that came with the watch, or;
      • A true 5W Apple (iPhone) or 12W (iPad) USB power adapter, or;
      • A third-party certified 5W (MFi) Apple USB power adapter.
    • Try to charge via a USB port (see following).
  • If loading via a USB port on a computer, make sure that you use a USB 2.0 or 3.0 port, the computer remains turned on and awake, and the cable is plugged directly into the computer (not on, for example, an external keyboard).
  • If your battery is very low, you may need to wait a few minutes for the green lightning appear (confirming that the charge has started).

  Once the load has started, you can tap on the screen at any time to check the progress (leave a few minutes at the beginning, where the watch is in charge of a very low battery level). A green lightning bolt symbol indicates that your watch is being loaded. It is normal the screen back to sleep while continuous load.

  More information:

  Check your battery and load your Apple Watch - Apple Support

• Why the temperature shows on my watch always different temperature on the watch of my husband when they use the same application?

  Why the temperature still showing on my watch shows a different temperature than on my husband watch when they both use the same weather app?

  Hi Jodie

  If you are each using the weather app (which is included in the framework of the iOS and watchOS), the following steps can help (followed by each of you):

  • On your iPhone, in the weather app:
    • If using anything other than the current location (which is included by default), make sure you have each added to a common location / city.
    • To add another location, select the icon «+»
  • On your iPhone, in the application of the watch, go to: My Watch (tab) > weather > default City > make sure you have each selected at the same location (for example: place of current residence or Mount Laurel).
  • On your iPhone, go to: settings > privacy > location Services:
    • Ensure that the location service is enabled;
    • Make sure Apple Watch is face value while it helps;
    • Check that the weather is set to always;
  • On your iPhone, go to: settings > general > background App update:
    • Check that the bottom App Refresh is enabled.
    • It can also help to activate the setting for the weather.
  • For optimal performance of your watch, keep the Bluetooth and Wi - Fi enabled at all times on your iPhone:
    • iPhone: settings > Bluetooth - on.
    • iPhone: settings > Wi - Fi - on.