TMS - SNMP Traphost endpoint address

Similar Questions

• TMS directory system endpoints source folder

  Hello

  I came across a rather baffling problem with a few cases of TMS and I can't for the life in me know as to why this is happening.

  I get the following.

  in the option for creating source directory Cisco TMS, I create a new directory and link with the MSDS files and select the folder where all the end points, this creates the entries in the phone book for me as I expect with one exception, I will detail below.

  H.323 = [email protected] / * /

  H.323 = [email protected] / * /< this="" is="" where="" the="" issue="">

  IP = IP address

  I find that on some systems (this doesn't happen to all systems) in the second entry of H.323, the H.323 entry where I expect to see the directory (also known as E.164 number) number I see a URI where a field has been added at the end of the number, I'll give you a few examples below.

  DN = 1234

  set field = @video.net

  random field = @newdomain.com

  IP = 10.10.10.1

  I expect to see the following.

  H323 = [email protected] / * /

  H323 = 1234

  IP 10.10.10.1

  but I don't actually see

  H323 = [email protected] / * /

  H323 [email protected] / * /

  IP 10.10.10.1

  I have purged the TMS systems and added, I searched through the xconfig for the NouveauDomaine which is invalid and I can't find anything anywhere other than on the list of areas configured SIP VCS parameters in the second area, endpoints have disabled by default SIP and in both cases I expect to see that under a SIP entry not an H.323 entry

  This is the origin of the problem of when a user tries to call via the Directory site remote also responds to busy VCS is unable to find the appropriate directory number because the location request contains the domain as well as the DN.

  I worked around this by adding a transform to the VCS who sees the patter of specific numbering and the bands of the area, so the calls work, but I still need to understand as to what is causing this behavior.

  If I had to create the directory entries by importing information from the record of the VCS seem to be correct, its only when I try to import the entries of the endpoint via the system folder in TMS (or more exactly to import the information stored in the file on the endpoint system) I see the problem.

  a very popular Adviser.

  See you soon

  Dave

  Hello

  Picked up that the case with David and it seemed that at least on the systems the international denomination on the mxp MXP has been configured. The area of intellectual property also has a configured domain uri that has caused the other symptoms. We where able to erase the questions but still yet to see if the client is actually affected by the same configuration "mistakes".

  / Magnus

  Sent by Cisco Support technique iPhone App

• TMS SNMP Version

  All,

  What version of the SNMP protocol use the TMS between endpoints & infrastructure products?  Is there a way to force the TMS to use v3 and disable v1 & v2?

  Thank you

  Justin Ferello
  Technical Support Specialist
  KBZ, a Cisco authorized dealer
  http://www.KBZ.com
  e/v: [email protected] / * /

  Nope, TMS does SNMP v.2. It is unlikely that we never introduce in favour of v.3.

  Kjetil

  Sent by Cisco Support technique iPhone App

• Directory of TMS on the endpoints registered CUCM TC

  Since 14.4.0 TMS version, it is possible get endpoint CUCM registered directory server to point to the TMS directory instead of the CUCM directory.

  I tried to set up, but I still can't get it to work.

  On the endpoint of TC (version TC7.1.3), in Configuration > System Configuration > Server from the phonebook,

  I set the server type MSD and the URL as http://TMSserverFQDN/tms/public/external/phonebook/phonebookservice.asmx

  When I SSH to the endpoint TC I ping the TMS serverFQDN so DNS resolution on the endpoint is apparently works.

  When I open this URL in my browser, I get a page called "PhoneBookService" with GetPhonebooks links, ResolveSystem and research

  But on the preview endpoint it works everything simply. This shows just "no directory.

  How can I solve this problem?

  A few quick questions that jump to mind are:

  1. Endpoints defined in TMS?
  2. A TMS directory is published at the endpiont in MSDS?
  3. The directory TMS has a source valid and entered in it?

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate

• SF300-24 - snmp get mac address information is not available?

  Hello

  IM sitting with a few cisco sf 300 24 switches and I try to get the Mac - the switch addresses learned from every computer connected to the switch... however... I can't find the OID of the tree of the mib that can provide me with this information...

  I hope someone can help out me!

  version of the software running im 1.2.7.76

  and mib files: 1.2.7

  -Greetings

  Claes

  Hi Claes, according to me, it's

  1.3.6.1.2.1.17.4.3.1

  dot1dTpFdbEntry

  -Tom
  Please mark replied messages useful

• TMS shows VC as ANY HTTP RESPONSE endpoints

  Hi all

  TMS poster telepresence endpoints units under NO RESPONSE HTTP status

  After the upgrade successfully 100 end points TP to 7.3.6 with TMS version 14.5 firmware.

  a few end points reflecting the situation as no respose http under TMS - section endpoints.
  -cannot reserve conference with these devices affected not showing the status "no http response '. individually all works very well.
  Please see instant.

  Note: They just can't be seen from the MSD. I can their ping server fine TMS. :

  Derrick

  TMS is currently running on Windows 2008/R2?

  If so, one of the more recent versions TC removing support for TLS version 1.0 protocol.  Windows Server 2008 and 2008 R2 have TLS 1.1 and 1.2 are off by default, you must enable (google, just need something changed in the registry).

• schedule meetings with the TMS and CTManager on the same endpoint

  Hello everyone

  I explain my problem, we have a CUCM with CTManager to plan meetings of the CTS, we have 2 VCS with a TMS to plan meetings of TC endpoints also.
  Our TC end points are saved in venture capital using H323, recorded in CUCM using SIP and exchange of email to can program using the CTManager. And TC endpoints are supplied by our TMS.

  As endpoints of TC may appeal to the endpoints CTS sometimes we have meetings planned between TC and CTS endpoints in the CTManager, but if schedule us a meeting by using the TMS, meetings of CTManager disappear and endpoint show TMS meetings, if we do a resynchronization of the electronic mail room in the CTManager We can see again in the meetings of CTManager in the touchscreen.

  We tried not to allow bookings for this endpoint of TC in the TMS, but later there is no way to schedule a meeting for this endpoint, even using the external call.

  You know any workaround solution to activate the two calendar options running on the same endpoint without removing the CTManager meetings? We don't need the BBFRR for the TMS meetings, only for meetings of the MLC.

  Best regards

  Hello

  Disabling power of the TMS write calendars 'Meetings' on managed systems is not supported. If an endpoint is added to the TMS, TMS assumed that endpoint is not used in another system of planning (such as CTS - man) and could replace any parameter that depends on the other system of planning.

  Kind regards
  Kjetil

• OSB - detection of address of endpoint of a route in the request action

  Hi all
  
  I need to detect the address of endpoint of a routing inside the pipeline of action demand that routing to send it to a legend of Java. Can someone help me how to detect?
  
  Note: I tried to access it from two $outbound and $inbound variable transport paths. Both return null in the pipeline of action queries. Either way, version of the OSB is 10gR 3.
  
  Thanks in advance.
  
  Published by: Serhat Dirik May 13, 2010 12:41 AM

  I'm not aware of any "routing endpoint address. I think that you can define service and exploitation at the action of routing, and you cannot set the end point it. So I guess that you are referring to the URI of a business service that you define for the routing.

  If this is the case, then Yes, you can not read URI (or end point if you wish) of this service of the company at run time. I have addressed a service request Oracle support a few months ago. They confirmed that it was currently impossible for this use case and arranged an enhancement request.

• Question TMS (14.3.1) of directory.

  Hello

  When you set up ' phone book server 1 "in the endpoint, I found a problem.". "

  I put the phone book server in endpoint as URL of TMS. If it was like http://xx.xx.xx.xx/tms/public/external/phonebook/phonebookservice.asmx (xxx indicates the IP address of the TMS)

  But I decieded to use the DNS server to ensure interoperability with TMS. Then Server TMS now has the DNS domain name.

  Also I updated the value of domain address "1 phone book server URL" in the endpoints and it was like http://abc.efgh.com/tms/public/external/phonebook/phonebookservice.asmx (abc.efgh.com specified address field of TMS).

  As directory services are a TMS, I made this change. However, after some time, this directory server URL has been changed to automatically IP address.

  I tried a different way to set the address of field of MSDS, but all failed. DNS host name has been fully qualified.

  I still don't understand why this problem happened. It's something like a bug.

  Here's my try:

  1. check if the "default configuration for the discovered systems model" could harm the subject.

  -activate/deactivate or activate with fillng domain address in the value of the "URL of the server to the phone book 1. But it does not at all on this subject.

  2. check if the "apply Manangement System parameters" could adversely affect this topic.

  -Records as 'No', but it does not affect at all on it.

  3. check if the "connectivity for systems system update" could adversely affect this issue.

  -Set the value as "manual." But it does not at all on this subject.

  4. I join the General settings in TMS as the configuration of the phone book.

  Is there someone who has the same problem or workaround for him? should I open a case... ?

  Kind regards

  Paul.

  Would have been nice if you could have done the same thing since the final point, but I don't think that it is possible to run nslookup from the admin, log in using SSH, might be able to do root-never tried, so don't know.

  However, if wireshark watch TMS evenly sending IP address instead of the FULL domain name, then it might be time to prosecute TAC.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• C40 Codec recording does not address right directory

  Hello

  I have a codec C40 sent recently to Cisco (RMA).  One of our guys put in the wrong directory address.  However, when I try and change it, it works.  However, after about an hour I watch the codec and the address changes to the original wrong address.  I tried about 5 times last week and had no luck.  Thanks in advance for your help.

  Tim

  Hi Tim

  TMS has a setting in the network settings: apply settings management

  TMS requires the address directory and management, the return address. The address is pushed is the address ipv4 (also a field in the network settings of TMS). If you typed in the FQDN of the TMS, TMS will prefer this address and impose this on endpoints. In this case the endpoint have need of a valid DNS server to resolve the FQDN.

  TMS pushes this address on a period of time, even if you change manually, TMS replaces it. If the endpoint is on the public internet 'public ip or domain FULL name' will be pushed to the system. It depends on the State of the system (accessible on the Public internet or local network)

  Amit brings also a valid answer here with models of configuration pb url can be configured here as a persistent parameter, but AFAIK the persistent model is pushed on an interval daily until at least its more likely the willingness to apply management settings is the sinner here.

  Make sure that the addresses of TMS is correct. To prove the theory, you can manually change on the endpoint, and then go to the endpoint in the system browser click on the settings tab, then change the settings and at the bottom there is a button "apply settings management." Click this button and check the address of the phone book, it changed to the wrong address now?

  / Magnus

• VCS FindMe vs TMS FindMe

  Ladies and gentlemen,

  I have integrated our VCS (including management FindMe) in terms of a TMS, but subsequently in the VCS > status > Application > menu user Lync State I see the CMRS only, but not the end points recorded.
  I have several questions:

  1. How can I configure the TMS to publish endpoints of telepresence as an account FindMe (to see them as a registered Lync client)
  2. Currently all CMR have the status offline, is it possible to change their default online status?
  3. Finally: How can I restore the FindMe management to VCS of the TMS. In the latter case, I would be happy if I could put in place.

  Thank you
  Laszlo

  You can use TMSPE for a variety of uses, such as the provision of devices, FindMe, Collaboration meeting rooms, etc.  In your case, you use it to FindMe and CMR.

  Under Provisioning > users, manually create or import AD users and assign them a 'video address model. "  The boss of the address of the video will be their address FindMe and them will automatically create a FindMe account for each user in Provisioning > FindMe where all you have to do is to create associated device addresses, and locations, etc. that will connect to the address the user FindMe.

  The menu devices is for devices implemented and can be ignored in your case because you are not provisioning all devices through the VCS.

• network flow - how to get the URL of the remote endpoint?

  Hello!

  I have a project running with a host to send messages to a target of RT (cRIO) via the network stream.  It works very well.  Now, I want to set up a feed back from the target to the host, but I'm stuck on a technicality: is it possible for the reader to automatically extract the network of remote endpoint address in order to implement the return flow?  I looked in the node property expecting to find something like "URL of remote endpoint", but I can't.   As a solution I might always have the host send its address as a message through the first stream as part of initialization, but which seems to be a shame as the target clearly already knows the address of his partner.  Am I missing something obvious here?

  Thank you very much!

  Hello

  Why do you need IP address of the host in the target?

  You need create endpoint writer on the target and create endpoint of reader in the home by giving the IP address of the target. I put what I hear in the images below.

  Point endpoint target writing:

  

  Point endpoint host drive:

  

  Maybe I'm missing something...?

  Thank you

  AREV

  CTO | RAFA solutions

  

• REDUNDANCY OF TMS

  Hello

  One of our customers is to have a primary site and the recovery for the conferencing site. They are planning to implement redundant VC a componnents like VCS, conductor, MCU and TMS.

  I need your expert opinion in the deployment of the TMS in the main Site and recovery Site scenario.

  Primary site and recovery Site is in a totally different network. We cannot extend the primary IP address on the site of DR. Because of this redundant components will have the IP address to a different subnet.

  TMS Server A: 10.10.10.10

  TMS Server B DR Site: 10.20.20.20

  DNS A record for TMS server is tms.example.com--> 10.10.10.10

  I checked the options for redundancy of TMS, as shown in the link.

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/TMS/config_guide/Cisco_TMS_Server_Redundancy_Config_Guide_13-0.PDF

  Fully redundant use the concepts of the load balancer.

  I have the following questions.

  1 could you please let me know what load balancer can be used for redundancy of TMS solution considering the IP address of the MSDS are in different subnets.

  2. in several servers, manual failover option, if the failure of the principal server will we use 10.20.20.20 address IP Cisco TMS Server Local IPv4 address and update the DNS record to point to 10.20.20.20.

  Krishna.

  Option a.

  I would not recommend an A DNS record pointing at a time... since it is essentially a round robin... which means that if DC 1 is down, you will get a search on the second, it will just fail. Therefore, I would recommend you do is just enter a DNS record for the DC 1 TMS and if you get a failure on DC 1, then simply go to DNS and to update IP address for this record to the DC 2 TMS.

  Option B

  No, you don't want to do this, i.e. Add the EPs for the two TMS initially. You only want to add systems to the DC 1 TMS... which means a TMS db to "govern together." And that's why your "asynchronous mirroring ' the TMS of DC db SQL to CC 1 2 SQL." And specify "async mirrroring in SQL", when you set the "async mirroring" in SQL, a db is 'active', while the other is "passive". That's why on the DC 2 TMS all services of TMS needs for people with reduced mobility because it cannot connect to the TMS SQL db (tmsng), which is passive. And with "async mirrored" on and how often you 'mirror', the basics of data will actually be the same.

  At the end of the day, the deployment is not that big (20 systems) so all this may seem "exaggerated", but it is the approach to 2 x installation DC... unless of course you virtualize everything and go Nick road, i.e. the Group OTV and strecthed.

  Rgds,

  Dale

• Migration of TMS/VCS to CUCM

  Hello

  I was wondering if anyone can help please. I had a customer who uses VCS? TMS. Every endpoint registered in VCS - C.

  I need migrat ethem to cucm 10.5.

  What will be the best way to go, any suggestions will be appreciated.

  Thakns

  Of TMS directory are what kind you referring?

  You can use TMS to a source of the telephone directory with the telepresence endpoints registered to CUCM, see pg 24 in the guide I linked to in my first answer.

• Cisco TMS first activate Idle all sessions

  Hello.

  We have the video conferencing system with Cisco TMS, blades MCU 8420, Tandberg Gatekeeper and Cisco in the series C endpoint, MXP series etc...

  This week we have problems with planning because when we planned to meet his past of in waiting for idle session direct and all sessions the codec says no connection.

  never start the meeting on active sessions.

  then that we end the session or meeting and reprogram this session and that begins at the current session.

  IM verified the conectivity between Cisco TMS and MCU, Endponits its Ok.

  rigth now we rebooted the server and MCU and the GA but when even continue the problem.

  The cisco TMS its located in other areas with transit to WAN network. We reserve the bandwidth with QoS for video, voice and data for im MCUS and endpoints asking its required reserve BW TMS Cisco commands API, Https, Https and other protocols? the problem may be congestion in WAN networks?

  This Protocol should ensure guarantee connect API orders end to end of Cisco TMS - MCUS and endpoints.

  I appreciate your support.

  Giacomo BR P.

  I did not completely understand your description.

  The communication is done on MSDS by HTTP or HTTPS, depending on your settings.

  In general, I would say that the management / follow-up will also through these ports, I would

  expect tickets with problems logging on your TMS.

  I could look at the logs and see: is the Conference properly generated on the MCU.

  is the dial in number okay, can the scope of endpoint the mcu, can the mcu reach end points.

  y at - it something suspicious on the GK, conferences and any other reservation of port

  on the MCU