TO RECONFIGURE MY WINDOWS SYSTEM

I want to uninstall and reinstall windows vista because my virus in my computer
can u help me?

Here are the different ways to reinstall Vista to factory settings:

How to get Vista recovery Media or the Vista recovery Partition on your computer back to factory settings.

There is no Vista free download legal available.

Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

Normally, they do this for a cost of $ small.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

Normally, you have to press F10 or F11 at startup to start the recovery process...

Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

You can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

They will tell you how to do this.

Every computer manufacturer has their way of doing recovery disk/s.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.

There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

http://support.Microsoft.com/default.aspx/KB/918884

MS advice on the conduct of clean install.

http://www.theeldergeekvista.com/vista_clean_installation.htm

A tutorial on the use of a clean install

http://www.winsupersite.com/showcase/winvista_install_03.asp

Super Guide Windows Vista Installation

After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

Save all data, because it will be lost during a clean installation.

See you soon.

Mick Murphy - Microsoft partner

Tags: Windows

Similar Questions

  • Noise - HHCTRL. OCX occupied an address box reserved for Windows system DLLS

    OK so I have a satellite phone and since yesterday, whenever I turn on my laptop, I get this message: -.

    RTHDCPL. EXE - repositioning of unauthorized system DLL
    DLL user32.dll system was moved in memory. The application will not work correctly. The move took place because the DLL C:\WINDOWS\system32\HHCTRL. OCX occupied an address box reserved for Windows system DLLS. The vendor supplying the DLL should be contacted for a new DLL

    So, I sat like 1 million bulletin boards etc. and not got anywhere. I'm normally ok with computers, but this time I confess that I have not the slightest idea what to do. It of really bugging me, can anyone help? Some message boards have taken me to a link on the Microsoft Web site to download something, but it says you must have windows XP service pack 2 and honestly, I have no idea and do not want to download something to totally screw up my laptop! (ok, maybe I'm not very good with computers!) Also, I found a site telling me something to do but I had no idea where to go or anything! I need someone to tell me EXACTLY what to do to get rid of this really annoying message. Also some sites say that when you press 'OK' another message appears, mine isn't it just goes!
    Please help, has soon x

    Please do not post new discussions on the topic that were discussed here in the forum. I always recommend looking before opening the new thread.

    Then please check this:
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=21936

    This problem occurs because Microsoft released a new patch for the closure of a breach of security in Windows Internet Explorer.
    But this patch has a bad influence on the Realtek audio chip.
    That's why Microsoft has released a patch to fix the old fix. ;)

  • Recover Windows System Image in Boot Camp 10

    Hi all

    I have problems with Windows on my iMac.

    So I installed Win10 using the Boot Camp Assistant, partitioning 300 GB for it. After awhile, I realized I want to segment much more, so I tried looking for a way to extend this partition to 500 GB - I have tried it with a 3rd party app and didn't. I then created a Windows System Image, restored the fuser unit to a single OS X partition and reinstalled Windows with BCA - by then I had decided to partition 1 TB for each operating system. I installed with no problems and tried to recover Windows from the Image of the above system. But instead he apparently formatted my entire SDS, including the OS X partition, that the iMac will not start and more.

    [I have a backup Time Machine and everything, I also know I have to reinstall OS X and then restore from that backup.]

    The question is how to do what I tried bypassing Windows format the whole * thing. If this is not possible at all to recover from the image, I'll be forced to 'start from scratch' and I'd really rather not, 3rd party applications are welcome at this stage. Also, can I recover the files from the Image of the system?

    Thank you for your time,

    Bruncky

    PS. : Given that the Apple employee didn't know immediately what I was talking about: in Windows, a System Image is a 1:1 copy of my Windows partition around, as opposed to a backup that saves only files apps and not content generated by the app.

    PS2. : If I reinstall OS X from Recovery Mode, do I make specific configurations about the merger by car?

    BrunoBrunck wrote:

    But instead he apparently formatted my entire SDS, including the OS X partition, that the iMac will not start and more.

    This issue arises from a bad assumption made during the restorations by the process of restoration of Windows. It assumes that the restoration is made on the dedicated disk that has nothing else. Winclone is the best solution on Mac instead of Windows System Image backups. I have some time with a few users and I have tried with different levels of success. Please see Bootcamp not recognized after the restoration of Windows from image system for example.

    The question is how to do what I tried bypassing Windows format the whole * thing. If this is not possible at all to recover from the image, I'll be forced to 'start from scratch' and I'd really rather not, 3rd party applications are welcome at this stage.

    Try of Winclone.

    PS. : Given that the Apple employee didn't know immediately what I was talking about: in Windows, a System Image is a 1:1 copy of my Windows partition around, as opposed to a backup that saves only files apps and not content generated by the app.

    There may be some confusion between the Image of the system and the history of the files. Time Machine has no concept of an Image of the system, so it is also the terminology 'exotic '.

    PS2. : If I reinstall OS X from Recovery Mode, do I make specific configurations about the merger by car?

    No, unless you have built a custom Fusion car. If you have a Bootcamp partition on the drive of Fusion, you want to ensure that you're not crushing BC/Windows, unless a wipe/restoration is your goal.

  • labview 6.1 with windows system error 7

    I use vi Labview 6.1 to control an oscilloscope Tektronic and a universal pulse BNC via GPIB-USP connection generator. The vi worked very well with the windows XP system. The system was changed to Windows 7. Then the error (Trigger signal is not recognized. Check the connection between "Trigger out" and "at the ins') comes every time I started running vi. The link between "Trigger out" and "at the ins' works under mannual mode, so it's really ok.

    Compatibility between Labview 6.1 and windows 7 would be the reason? If so, are there tips for using Labview 6.1 on windows 7?  Thank you.

    Thanks for your help.

    The solution turns out to be very simple... The new Windows system is the German version so that the old windows English version.           , is used for decimal in German instead of .

    Thank you all!

  • Windows system error: there is an IP address conflict with another system with the network. How do I remove this error message?

    I just installed a new internet provider and all of my connections are working fine, but I constantly get this "Windows system error: there is an IP address conflict with another system with the network." I have my electrician of the internet modem connected to my office. I have also two wireless devices connected to the appearance of the Modem wireless. I constantly get this error message mentioned above, and I want to get rid of it.

    This means that all that he says.  Your Windows system has an address that already exists on your local network.  Turn your system off and use a working system to locate this address and to which unit he belongs.  In most LANs, the router's DHCP server.  You may be able to ask the router which addresses are used and see what device uses this address, but I suspect not.

    Duplicate addresses can occur when two systems received the same address manually, or when we got an address in the DHCP of the router range. It is unclear when this happened because he is not in control of the address and puts the address duplicate to a second system.  You need to track down, ensuring that all addresses manually asigned are out of the DHCP range, that you book the address of the router, if you want the device to use this address, or configure all devices to request the address of the router using DHCP.

  • Repair Windows system is available on a disc of Windows 7 HP system recovery

    Repair of Windows systems is available on the disk HP System Recovery DVD for Windows 7 and if so how I find the disk? I was looking for Windows Bootrec.exe!

    Hello:

    No, it isn't.

    Simply make your own drive of W7 installation/repair by downloading the file from W7 ISO applicable from the link below for the version of W7 you have.  Use the files in the list update to SP1 Media.

    dows-7-Digital-River-direct-links-Multiple-Languag http://forums.mydigitallife.info/threads/14709-win...

    You can then use this tool to transfer the ISO on a DVD or 4 GB USB key file.  The tool also performs the bootable media.

    http://www.microsoftstore.com/store/msusa/HTML/pbP age. Help_Win7_usbdvd_dwnTool

    Start on the W7 installation screen, and then on the lower left side of the window "Install now", you will see the repair option.

  • What laptopi marketing get this time ewery on screen; dll c:window\system\spool\divers\x64\lxcf. missing entry @16

    Hi when I start my laptot get this time on screen, c:window\system\spool\driver\x64\3lxcf time.dll ewry. lack of entry_run [email protected] it please can someone tell me what it is regarding

    This DLL (for example, Dynamic Link Library) would have to do with a dynamic timer in your Lexmark printer software. The Lexmark printer software is configured to load each time that you start the computer, so when Windows starts, this error occurs.

    First of all, I would like to see if the Lexmark Support site has an update for your printer software. If no update is available, the original software and reinstall it. Who would recreate the DLL registration and should solve your problems.

  • C:\WINDOWS\SYSTEM\VMM32 file is damaged on the Windows ME startup

    Original title: C:\WINDOWS\SYSTEM\VMM32

    I'm after start on my spare charge of problems with Windows ME computer, and now starting will not continue beyond a message which States that the following file is corrupted C:\WINDOWS\SYTEM\VMM32. Also, I don't have a key-on this computer. Help please. John.

    Hi John and ME,

    Unfortunately, Windows Millennium Edition has become an obsolete product and Microsoft has stopped supporting the product.

    For more information, you can consult the following articles:

    End of support for Windows 98, Windows Me and Windows XP Service Pack 1

    Support for Windows Millennium Edition

    However, you can try these steps and see if it helps.

    Step 1:

    You can try to start in safe mode and check if the problem occurs.

    Check this link for more information on starting your computer in safe mode:

    A description of the options to start in Windows XP Mode

    Step 2:

    If you can boot into safe mode without any problem, and then try to perform a clean boot.

    A clean boot to check if startup item or services to third-party application is causing this issue.

    You can read the following article to put the computer in a clean boot:

    How to configure Windows XP to start in a "clean boot" State

    After you have used the boot is a way to solve your problem, you can follow the steps to configure Windows to start normally.

    Hope this information is useful.

  • Windows system error message

    We just installed a wireless modem. Sometimes pops up a message that says

    "Windows - system error".

    There is an IP address conflict with another system on the network. »

    What it means?

    This means there is another adapter or ethernet Wi - Fi on the network (which is connected or passing by it), who uses the same IP address. You must change one of the IP addresses

    You can't have 2 computers with the same IP address. Look under the properties of the adapter on each computer. Under IPv4

  • Windows system error: a duplicate name exists on the network.

    I get an error message from windows at initial startup. The message is "Windows system error: a duplciate name exists on the network." How can I fix this?

    What version of Windows, including the service pack is installed?

    After the error, can you use the computer to access the Internet?

    You have a home network (i.e. more than one computer sharing an Internet connection) or this error pops up on a computer used in a business/company/Office?

    Assuming that there is a situation of home, what has changed recently in what concerns other devices (computer, printers, game boxes, etc.) added to the mix?

    How this computer is connected to the Internet?

    Make a right click my computer and select Properties.  Then click on the "Computer name" tab  The 'full name' should not be the same as the name of "workgroup".

    The error is a complaint that another device on any network to which your computer is connected to has the same name that the 'full name' shown in system properties (I assume that it is also possible that the error reports that there are two devices on the network with the same name even if none of these devices your computer).

    Although there are utilities that scan your network and to report the names of connected devices, they are somewhat nonsimple to use and may not work on a computer that will expose the error that report you.

    If your computer is on a home network, share an Internet connection using a router, you can manually check all other devices.  You don't maybe not easily able to determine the 'computer name' no computer network devices, but it is highly unlikely that such a device, for example, a network printer, would have the same name as your computer.

    Just to be sure there isn't something special going, disconnect your computer from your network (or your Internet connection) and then it reboot.  The duplicate name error should NOT appear if the computer is not connected to a network.

  • Every day I get this error message and send it to Microsoft. 32\svhost.exe C:\Systems32/Drivers\c30a67ae1d5f4bd4.sys AND C:\Windows\system

    Every day I get this error message and send it to Microsoft.  32\svhost.exe C:\Systems32/Drivers\c30a67ae1d5f4bd4.sys AND C:\Windows\system

    Also: Microsoft called me about a report of my computer.  My daughter thought it was a hoax and hung up.  Is there a way I can connect with this Department once again?

    Microsoft does not automatically contact you if you send details of error for them.  They use these reports to see what types of questions are trending and those that are trending upwards looked at herself.  The rest cannot.

    And your daughter has been very wise - the call she received WAS a scam and she did well to cling to their topic.  Microsoft never call you unless you call them first, and they tell you that they will call back.

  • How to determine if a USB device is plugged into a Windows system?

    I want to determine when a USB device (either external HD or USB key) was pluggeed into a windows system. Currently some systems will appear in the system log when they are connected, but the majority are not. Is there a way to check whenever one is plugged?

    I need information to view audit logs (System, Application, security)

    Original title: USB audit

    Thanks, CT

    There is a video on how to do it here:
         <>http://www.securitytube.NET/video/868 >

    Note that it uses 'gpedit', so it will apply to XP Pro and not XP Home machine.

    HTH,
    JW

  • Cannot remove any Dungeon now bytes not used to message cannot find C:\windows\system 32------rundll 32 exe

    Original title: t hink I deleted add remove program,.

    t hink I deleted add remove program, computer guard me tellin memory full, cannot remove no matter what now bytes unused Dungeon is message cannot find C:\windows\system 32------rundll 32. exe does anyone know what this means and how I can now delete files and programs to make more room, comp is need a cleanup and don't know what to do, any help would be received with gratitude xx

    Hi Juleskk,

    Follow the suggestions below for a possible solution:

    Method 1: You can try the steps in the article mentioned below and check.

    Cannot find the Rundll32.exe file when you open Control Panel

    http://support.Microsoft.com/kb/812340

     

    Method 2: I also suggest that you scan your computer with the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

    The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

     

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

     

    Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

    Important: While hard disk analysis if bad sectors are found when scanning try to repair this area, all available on which data can be lost.

    Method 3: Try the SFC (System File Checker) scan on the computer.

    To run the System File Checker tool, follow these steps:

    a. click Startand type cmd in the box start the search .

    b. right click on cmd in the list programs, and then click run as administrator.

    c. If you are prompted for an administrator password or a confirmation, type your password or click on continue

    d. at the command prompt, the following line and press ENTER:

    sfc/scannow

    See also:

    Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

    http://support.Microsoft.com/kb/310747

     

    File system (CFS) Checker

    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/system_file_checker.mspx?mfr=true

    Let us know if that helps.

  • How do you remove Trojan horse from the Windows\system\svchost.exe file located?

    How do you remove Trojan horse from the Windows\system\svchost.exe file located? I worked on this problem for 5 days. I've tried everything except wipe the hard drive completely and starting over. Windows xp pro sp3

    I bought a new diagnosis program and quarantined the virus once it has been identified. I tried to remove the virus in several ways, but it comes back. The best way that I thought would work enter safe mode and by changing the attributes of the svchost.exe file and then delete and checked the registry AWI hwo to the Web site, but it continues to be problematic.

    Hello

    During the uninstallation of antivirus/antispyware/security programs always check for an uninstall
    tool and/or removal instructions special to avoid leftovers.

    List of tools to clean/uninstall anti-malware programs
    http://answers.Microsoft.com/en-us/protect/Forum/protect_start/list-of-anti-malware-program-cleanupuninstall/407bf6da-C05D-4546-8788-0aa4c25a1f91

    Uninstallers (removal tools) for common antivirus software
    http://KB.eset.com/esetkb/index?page=content&ID=SOLN146
    ------------------------------

    Here's what I use and recommend: (these are all free and very effective versions.)

    Avast and Prevx proved extremely reliable and compatible with all I have
    launched on them. Microsoft Security Essentials and Prevx have also proven to be very
    reliable and compatible. Use MSE or Avast and Prevx, Prevx 3 but not all.

    Avast Home free - stop any shields is not necessary except leave the file system, Web,.
    Operational network (Script and behavior are also recommended in Ver 6 +).

    Prevx - Home - free

    Windows Firewall

    Windows Defender (is not necessary if you use MSE)

    Protected IE - mode

    IE 8 - SmartScreen filter WE (IE 7 phishing filter)

    I also IE always start with asset if filter InPrivate IE 8.
    (It may temporarily turn off with the little icon to the left of the + bottom
    right of IE)

    Two versions of Avast are available 6.x and 4.8 x

    Avast - home - free - 6.x stop shields you do not use (except files, Web, network, &)
    Shields of behavior) - double click on the icon in the Notification area - real time Orange - click on the
    Shield that you want to stop - STOP. To stop the Orange icon to show an error indicator-
    Click on the Orange icon - top right - settings - click on the status bar - uncheck shields you
    disabled - click OK
    http://www.avast.com/free-antivirus-download

    Avast 4.8 x - home - free - stop shields, you don't need except leaving Standard, Web,.
    and the network running. (Double-click the blue icon - look OK. - upper left - Shields details
    Finish those you don't use).
    http://www.avast.com/free-antivirus-download#TAB4

    Or use Microsoft Security Essentials - free
    http://www.Microsoft.com/Security_Essentials/

    Prevx works well alongside MSE or Avast

    Prevx - home - free small, fast, exceptional protection CLOUD, working with other security
    programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here
    or use Google to see how to remove.
    http://www.prevx.com/   <-->
    http://info.prevx.com/downloadcsi.asp?prevx=Y<-->

    Choice of PCmag editor - Prevx-
    http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

    Also get Malwarebytes - free - use as scanner only. If you ever think malware and that
    would be unusual with Avast and occasional Prevx running with the exception of a low level cookie
    (not much), to UPDATE and then run it as a scanner. I have a lot of scanners and they
    never find anything of note that I started to use this configuration.
    http://www.Malwarebytes.org/products/malwarebytes_free

    I hope this helps and happy holidays!

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • How to solve the "HKEY_LOCAL_MACHINE Windows Search\Gather\Windows\System Index missing or invalid" error message

    'HKEY_LOCAL_MACHINE Windows Search\Gather\Windows\System Index missing or invalid' error message appears after each Norton Utilities scan.

    The problem is that IE frequently slows down or blocks, the Task Manager shows the CPU clocked at 100% the problem will clear for 5-10 minutes.

    I am running Windows XP Home Edition with Norton Utilities; Norton Antivirus; Advance system care and Super AntiSpyware as my software security.

    Anyone had any chance to solve this problem?

    Thank you

    Richard Boyer

    Hello

     

    ·         Is your update of the antivirus program?

    ·         Were there recent changes made on the computer before the show?

     

    Follow these steps and check if that helps.

     

    Step 1:

    As you receive the error message when you use Norton, I suggest you to contact Norton support:

    http://us.Norton.com/support/index.jsp

    Step 2:

    I suggest you run this Microsoft Fixit tool and check if it helps.

    Solve Internet Explorer add-on problems when IE hangs or freezes

    http://support.Microsoft.com/mats/ie_freezes_or_crashes/en-us

    You can also view this article to improve the performance of Internet Explorer and check if it helps.

    Internet Explorer is slow? 5 things to try

    http://Windows.Microsoft.com/en-us/Windows/help/Internet-Explorer/slow-five-tips-to-boost-performance

Maybe you are looking for

  • do you want to go back to iPhoto - hate Photos

    When I try to use iPhoto he says because all my pictures are Photos in iCloud, none of the changes I make appears in two places.  How can he?  must I download pictures back from iCloud, transfer photos in iPhoto, then move iPhoto to the cloud.  don't

  • Lack of network card

    I just installed a Windows 7 64 bit on my HP Pavilion DV6-7014nr (Professional), and now he is unable to detect any network. I checked the Device Manager and there is not even a tab for network cards and the only message I see on the diagnosis is 'in

  • How to make certain elements in the inactive toolbar

    While running my program, I need to turn this off (grayed out) some of the items (icon) in the toolbar, y at - it a function in Labwindow CVI to do this? Thank you

  • The MS Virtual WiFi Miniport map my willing Lalonde of an error code 43

    Diag Windows gave the error message "remote device or resource won't accept the connection. message that appears is "windows has stopped this device because it has reported problems (code 43)."

  • SG300-28MP power inline or stop?

    I have a client with a SG300 28MP and they want to be able to stop or turn on wi - fi when ever.  Since I'm AMX touch mounted panels in various places, I want to give them the opportunity, via touch screens to enable or disable, or even to choose pow