To the Satellite A200-23d HARD drive recovery
Here is someone who knows if the Satellite A200-23d has a HARD drive recovery integrated?
I can't say for sure, but I'm sure it comes with a 99% HARD drive recovery image.
Can you please tell us what your problem with this model of laptop?
How can we help?
I have a Satellite A300, and I deleted by mistake HDD Recovery folder.
I have recovery disks, but I want the HDD Recovery folder to restore my system without using the discs.
Please, can you tell me how to recreate the HDD Recovery folder?
Thank you very much
Unfortunately, now is not impossible to recover, image of hard drive, but with the only recovery disk. You can copy only to someone who has the same laptop with hard drive recovery record.
Post edited by: Jeka-HE
Here is someone who knows if the Satellite A200-23d was a resumption of the video card?
Native video card ATI Mobility Radeon HD 2600 512 MB does not.
Can I replace it with another video card?
What do you mean by video card recovery?
Do you mean replacement/upgrade graphics card up-to-date?
The notebooks of the graphics chip cannot be upgraded or replaced. It s mostly a part of the motherboard and if something goes wrong with the graph of the chip you have to replace the motherboard.
I have a PC laptop toshiba Satellite A500-1CO.
Previously, when I wanted to again pour Windows
Recovery program HARD drive that I used
But now I delete d:\HDDRecovery folder and when I run the HARD drive recovery program a mistake with this article shows you:
Folder HDDRECOVERY not found in d: \.
Excuse me for my bad English
> But now when I run my program of recovery of HARD drive
> An error with this article shows:
> Folder HDDRECOVERY not found in d: \.
Have you checked if the folder in hard drive recovery leaves the local d? Perhaps, you have removed before...
The drive HARD in my Toshiba Satellite A200 PSAF6A-0US01N is not recognized in the machine or any other computer, so I can't run any windows/toshiba repair.
I know that readers have a factory reset hidden on the disc and press 0 to the power upward, but with the unreadable disk, how can I repair my installation of Windows Vista?
If the HARD drive is not recognized by the BIOS or other laptops, then I would say that your HARD drive is defective.
In this case, you need to replace the HARD drive.
In this case, you will not be able to start the recovery procedure from the HARD drive because it works badly as he has already said
Are you from the Australia? If you need a recovery disk, I recommend contacting the local Toshiba ASP to get this drive
After losing the motherboard of my Satellite A200-23Z I need save some important files to hdd satellite. With external USB enclosure, I can only access some... Can't see program files, filesystem - really nothing disk system, a large number of files was on the desk...
How to get full access to all the hard drive? -to all logical drives?
Please - help... :(
I put t understand what is happening here. I have old P200 (similar to yours but with 17 inch screen) and when I connect the HARD drive as external HARD drive to my new P500 I have full access to all stored data.
There is no limitation at all.
> was a lot of files on the desktop...
Do you know how to find the right location for desktop?
Greetings. This text has been written through a translation program, to try to understand :)
My friend bought a few days back to herself TOSHIBA Satellite A200 (PSAE6) where it has been established operating system Windows Vista Home. He asked me to change OS on Windows XP Pro. With the first problem I have consulted - have deleted Vista, but to set up XP is not possible due to the absence of the HARD disk controller driver in the OS distribution kit. Windows Installer cannot find the HARD drive. I read that it is necessary to load the driver during Setup, press the F6 key. But a problem I can't find the driver in that.
We have no disk with drivers that should go with a computer and therefore it is necessary to search independently on the Internet. On the Toshiba site to locate the pilot, it was not possible. Then I came to the Intel site and download "RAID/AHCI - Intel® Matrix Storage Manager» After unpacking I got only «infinst_autol.exe» archive
Where can I download this driver (not a "EXE" format) that can be used during the installation of Windows XP?
PS: a chipset - Intel PM965 Express
use the files in the folder "ICH8M_32bit".
Can anyone tell me please what type of HARD drive, I need a Toshiba Satellite A200?
Is it an IDE or a SATA or something like that?
The A200 Satellite is equipped with a SATA HDD.
If you want a new HARD disk, you should a 2.5 HARD drive SATA interface. In addition, you can buy a HARD drive with SATA2 interface because it s downgrade compatible to SATA1.
I have an old Satellite L20-100 and it has a few problems with the HARD disk. I want to buy a replacement (new HARD drive) so I need to know what are the types of FDI in L20 - 100 discs...
In addition, what type of DDR2 RAM I should buy to install in this laptop?
Don't want to buy a fake, because if I do, it would be very difficult to sell...
Please, help :)
Post edited by: in_silent
I agree with Akuma L20 supports a SATA controller and you need and 2.5 SATA HDD.
Usually it s no matter which manufacturer is all 2.5 SATA hard drives must be compatible
With regard to the 48-bit LBA:
As far as I know that this could be just a problem with HDD IDE (P - ATA). SATA HDD should not be affected. So, theoretically, you could upgrade the HARD disk using larger than 128 GB.
Regarding the upgrade of memory:
You need DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM and you can use 2 x 1 GB RAM
I own a P133 Satellite with a 80 GB HARD drive and I would like to replace the HARD drive.
1. How do I "safely" take it out?
2. how GB support Satellite
3. likely to be mounted a Toshiba no? 99% of Yes, but sometimes producers are naughty and try to get you to buy what they want and therefore lost a customer!
Can anyone help with these questions?
First a question; You really a P133 Satellite?
This laptop is not known to me and I don t I think this series exists.
I saw your other thread and it seems that you have a Satellite P30. Am I wrong?
OK I'll try to give some info on the P30.
(1) the location of the HARD drive is located at the bottom of the unit. You must turn the computer. Remove the two black screws to release the HARD drive door. Pull the tab to remove the HARD drive unit. Remove the HDD Enclosure HARD drive. Note: after the removal of the portable computer HARD drive you need to remove also the brackets that are piling up on both sides of the HARD drive.
(2) you can use the 2.5 ", 9.5 mm HDD with capacity 30 GB/40 GB/60 GB/80/100 GB / 120 GB. The HARD drive should support the Bus Master IDE and 100 synchronous DMA Ultra
(3) as far as I know you can use HDD from different vendors, but hardware specifications must be supported (see point 2 :)))
I had a bad hard drive crash. I installed a new and got the bios to boot from the cd drive, with windows 7
orginal cd of installation in the drive. He acknowledged drive 0, I clicked again in the options. He created a system partition.
Installed windows 7 apparently very well. Inserted the recovery driver and application and installed disk. Everything seemed fine. This morning I turned it on and it the hard drive error (3F0) Please install an operating system. I shut it down and restarted, it seemed normal. I installed a few programs, stop it again. Returned by, it starts again and it took me to screen diagnosis saying SMART Check - not installed and short DST - not installed... Can someone tell me how to remove that partition and I can format the drive in a usb sata enclosure and try again.
Please tell me the correct procedure to return this laptop running to a factory State. I have the original Windows7 and Windows8, Driver and Application for the two OS disks ' are... I want to stay with the installation Windows7.
Thanks for any help on this problem. I have no idea where I was wrong!
It is not impossible that the new disk is bad, have seen before. It is also possible that the controller sata on the motherboard is bad, but I'd watch this last possibility. You can get an Exchange on the new hard drive?
By turning on the laptop I get IDE #0 ERROR Inter (R) Boot Agent FE v4.1.09 etc. Insert system disk in drive. I do and nothing happens.
Is this to say that the hard drive is spent? If yes where can I get a replacement from? How I don't know what to buy?
Well, the ERROR IDE #0 means that the BIOS cannot recognize devices connected to the IDE #0. Above all it s a HARD drive.
So I presume that you HARD drive is dead and must be replaced.
You can buy a compatible HARD drive from a computer or a laptop computer reseller. Of course, you can contact your local Toshiba ASP (authorized service provider) and order this HARD drive too.
Your Pro A10 appears to bear an IDE hard drives.
Therefore, you might choose an IDE HDD with 20, 30 GB or 40 GB
I posted only these three sizes because I'm not sure about bigger hard drives.
Perhaps a larger HARD drive is not recognized by the BIOS.
See you soon
Basically, I had a problem a month ago where I got an error message during startup and wouldn't start windows (missing file) can't remember which exactly but it came out of nowhere? It was working fine then when I restarted ANYTHING.
Anyway I ended up installing ubuntu who found the HDD without any problem at all. Now to get this laptop on my fiance and ubuntu is not good for her! Windows setup is almost impossible! I tried to install xp because I have a drive, but during installation it doesn t find the hard drive at all!
I found that I maybe 3rd need drivers sata/scsi party I put on a USB key, the installation when you are prompted to install these I can t install from a USB only a floppy? Computer laptop hasn t had a floppy disk?
Could someone please help as I have tried everything I think and had no joy at all!
You can use nLite software to create a new XP CD and include drivers SATA (Intel Storage Manager) on this new CD of XP.
The nLite is a freeware software and you can find and download from many Web sites.
Google is the key ;)
I'm trying to restore to factory settings but have no luck.
I tried pressing F8 when the toshiba logo comes back, it goes to the screen of boot in advance and I select computer repair and it boots to windows. I don't get the recovery options.
I also tried pressing zero when switching on the laptop just rings home.
What im I doing wrong?
It is a vista running L300-149
As I see all you do is right.
Turn on your laptop and press F8 several times and you will enter the Advanced startup options
The first option should be repair your computer and after two or three steps, you should see The System Recovery Options , and last option there Toshiba recovery.
Have you used this recovery options in the past or you are trying to use it for the first time?
Recently, my laptop has been infected with many viruses Trojan horse. After using Malwarebytes to remove, windows would no longer. I read that I can start up taking 0 before feeding on restore to the factory settings. In doing so, I get a message at the bottom of the screen that says "* HDD RECOVERY MODE * ' but then nothing happens. I even left the computer for an hour to see if it would advance on the next task, but it does not.
I can not in safe mode. I am stuck and don't know what to do. I don't have a recovery disc either. Can anyone help me to restore to the factory settings?
You created the recovery DVDs?
I mean that if you have the recovery disk you can use to install factory settings.
Maybe you are looking for
We want to prepare for a big jump from the current environment to Windows 7 for Windows 10 Migration to millions of customers and application developers. We have a migration project plan but need more advice and support for a successful migration. O
Hello, I use a mac and recently received a notice on my CC that I need to download again - I think I accidentally deleted something that I shouldn't while cleaning up my computer.So I downloaded a new, but it would not install.I then found that I had
Hi allI try to print the following values of a table...abcdIIefghIIijklIImnopII5IIjklII9So after the 4th appearance of | character, I need numbers alone printed. That's what I have so far...Select substr (fld1, (regexp_instr(fld1,'[II][[:digit:]]+',
Hi I have an accidentally pressed cancel for more and he undid much of my work. How can I reverse cancel it?
I know that in the past I tried to combine hyper-v on a machine and vmware workstation that has not worked. I don't understand why because both probably need exclusive access for virtualization by the processor hardware. This use case will still work