Toshiba 46HL900A does not turn on

My TV turns completely. The Red led will turn from red to green, but the TV does not turn on? Someone knows why? Thank you

Hardware problem might be serious... to be honest, that you have some many options troubleshooting...
If its material of serious malfunctions, only an authorized technician would be able to help you.

Tags: Toshiba

Similar Questions

  • Toshiba Camileo P10 does not turn

    I have a toshiba camileo p10. The problem is that the camera does not turn. I tried to recharge the battery, but the red light blinks for hours.

    I tried without the battery and the charger plugged but nothing happened. I cleaned the contacts.
    All solutions?

    Have you removed the battery AND the AC adapter?
    Try this. The two parties should be removed/disconnected.
    Leave the camcorder for some time (a few hours). Press and hold button power 30 sec long. After this plug in the battery and charger.
    Wait until the battery has been charged and then try to turn on the cam by pressing the power button.

    Good luck buddy.

  • Toshiba 32RV635D does not power off when the computer turns off

    Hello

    I inherited a Toshiba 32RV635D. I have a PVR based on linux (Mythtv) connected to the TV via HDMI, connected on a Nvidia GT610.

    With my previous TV, a Vistron LCD Panel at low prices, he would go to sleep when the put PC into hibernation and light up when the PC came back.
    This required no configuration of me, he's done right. The Toshiba TV does not work.

    With this Toshiba TV, when the POR turns off the TV turns off screen but is actually still on - power led remains lit in green.

    Same thing with the other way around - if I put the TV in standby and powered the POR, the TV does not respond and I have to manually put out of Eve.

    I updated the firmware and it has not changed anything, and I can't find anything related to power management in the menus of televisions. I even tried just pulling the HDMI cable to the back of the TV so it has no physical active entry, and yet, it does not fall to sleep.

    The Amazon page for TV mentions the power management features, and I expected from what I understand, it should behave the way she.

    I read a lot on HDMI-CEC, but to use it with my existing kit, I would need to buy an adapter USB - CEC, and which seems a little odd because my previous TV not cheap-as-chips just done this...

    Also, the different uses in linux suggests considers its sounds the right - 'xset q' running when the computer is idle tells me that "the monitor is turned off" when in fact it is not.

    Clues?

    Ricklous, it can be useful if you have a look at the url
    http://www.Toshiba-OM.NET/LCD/PDF/English/Country_Specific/RV635-323742-English-specific.PDF

    If you want to download the manual of the English edition for your model, I have not read through, but it may be useful to you.

    Either by the way, I have the model 32RL900A and find only a VCR plugged into the claims of taking SCART screen every time it turns on while the TV is set to a string of FTA (Free To Air) and then 'hands back' screen when he (PVR) goes out, and this, I discovered, is a characteristic of the system SCART.

    I don't know if this information is useful to you, but hope it helps.

    donhe7

  • L50D-B-146 satellite does not turn

    Hello

    I have a problem with my L50D-B-146 turns is not on. Very rarely, when I try to turn it on it works. Once I managed to turn on I tried to upgrade the Bios to 1.6 1.2, but you must restart your computer to complete the installation I couldn't because it does not turn on 99% of the time. The laptop didn't work before I tried upgrading the Bios is not the fault of the installation to fail. Also when I get to turn Windows works perfectly fine, until I have to turn it off again.

    When I try to turn it on the power button light works and you can hear the fan, otherwise you may not even see the screen Toshiba Leading Innovation, so I don't think it's the fault of the window. I repeat again once you can activate from time to time, but very rarely. Also it is not the fault of the monitor that I connected the laptop to an external display, and again, there was a problem.

    I would be very grateful for any solution to this problem

    The solution to this problem?
    I don't know if anyone here can offer virtual diagnosis and offer the working solution.
    When the machine works sometimes such a problem is not easy to understand. Such behavior of the laptop must be analyzed and may be tested with diagnostic tools.

    What we do here, it's just to speculate at what may be the problem. Looks like the BIOS related issue. For some reason, from time to time your machine cannot pass the BIOS checking the material.

    Have you already contacted Toshiba services and asked for help?

  • Re: Satellite L750 does not turn on - LED flashes

    Hi guys,.

    Can someone help me please!
    I just bought a laptop Toshiba Satellite L750 last week and it won't turn :(

    The wing forward system indicator is flashing but I'm not sure wat it is: P
    Nûby - I know, but its all new to me.

    Also my lappy does not turn and stop automatically last night in the middle of using it.

    The fan seems to be surging so:(meh son seul nouveau... s'il vous plaît aider!!!)
    Karma

    Hello

    If the LED flashes then a serious hardware problem has been detected on the motherboard.
    I think that the guarantee must be valid because L750 model isn't very old so don t time in bulk and get in touch with the Toshiba ASP in your country.
    Guys should help you for free if the warranty is valid.

    For me it doesn't look like a main part (motherboard) need a replacement.

  • When I turn my iphone sideway, the video does not turn sideway

    When I watch the video on my iphone, I usually turn my iphone sideway, the video would turn sideways to get the most out of the video. But now it does not turn sideways.  Try to find the adjustment to set the option or the recent updated version this video sideway option removed.

    Swipe up from the bottom of the screen to get to the control center. Press on the icon of a padlock on the right side until it becomes black. If the icon is white, the screen rotation is locked.

  • The Web of Toshiba site does not recognize of my drive hard number and P/N

    Hello

    There is a little less than two months, I bought my HDD Toshiba Canvio Basics 3.0 from Amazon. The hard drive has stopped working for some reason any (I drop or something, it simply stopped working).

    Of course, I was trying to use my warranty to repair or Exchange it, but the Web of Toshiba site does not recognize my serial number and product number. They are just there, black and white on the sticker on the back of my hard drive, but the site says they are not valid.

    Someone has an idea what is happening? I would rather not throw 50 euros by the window for less than two months of use.

    Product number is HDTB105XK3AA - and not to HDTB105 * E * K3AA like some sites say (including Amazon).

    Thanks for your help.

    Stand by. Have you contacted Amazon using Amazon options for repair under warranty or Exchange?

    Check please help Amazon option and collect detailed information on defective, damaged or significantly different returns.

    Two years ago I had problem with the mobile phone bought by Amazon and I send direct Amazon with bill Amazon.

    By the way: can you please post the link where you have tried to check the serial number of your HARD drive?

  • Webcam on my Toshiba NB305 does not work

    Sorry to invade this question, but I couldn't figure out how to post a question that tells you how stupid I am.

    The webcam on my Toshiba NB305 does not work.

    When I go into programs he says neveer me a wizard will popup, but it does.

    Help.

    Hello

    Why you don t try to reinstall the webcam software?
    I think that the software is corrupt and who knows why.

    Visit the European driver of Toshiba page, choose your model of laptop, choose webcam software, download this and reinstall.
    Before beginning a new installation, you must remove the previous version

  • camera does not turn on

    I tried to load camera after death, it does not at all, but the orange light is on when it is plugged, let it charge all night and still it won't turn. I videos I would like back, please help.

    The charge indicator lights orange when the charging starts. It seems that the battery is charged. Try to turn on the camera while loading and check if it is turn on.

    Note: The charging light turns off, charging is completed.

    If the camera does not turn ON even when the load is in progress, the service is required.

    You can initiate the service from the link below:

    https://eService.Sony.com/

    You can also contact our telephone support or Chat to try additional troubleshooting procedures.

    http://eSupport.Sony.com/us/p/select-System.pl?Director=contact

    Please provide model # exact camera while contacting support, so that they provide accurate information. You can locate model # on the back panel and it will start with the letters MHS.

    If my post answered your question, please mark it as "acceptable Solution".

  • Satellite PRO U300 does not turn off

    Hello

    I am facing a problem for the last few days on my Satellite PRO U - 300 (31st PSU)...

    The machine does not turn off and the power light stays on (blue LED) even after you have disabled. In fact, happened 3 - 4 times when I start the computer normally by pressing the power button / stop, it does not start and I noticed that the indicator was not extinguished even after + shut down +. Like any it is blocked! I have to finally, remove and reinsert the battery to start the laptop.

    Some details of my pc are as under:

    Version of the OS Microsoft® Windows Vista Business 6.0.6001 Service Pack 1
    BIOS Version V2.00
    Processor Intel (r) Core (TM) 2 Duo CPU T7100 @ 1.80 GHz

    Can someone help me solve this problem. Is it possible that during the uninstallation of programs, any perticular driver file is also deleted?
    Thank you

    JITENDRA

    Hello

    I don't know that you understand the indicator of power, but to me it sounds like AC Power LED and this LED is always on when the laptop is connected to the power supply.

    Power on / off LED is probably what you mean (the other starting on the left).
    Anyway, you turn off your laptop using a standard on the Start button?
    Are you sure you want to use the Hibernate mode.

    Believe me, the entire description here is pretty confusing to me. It may be that the laptop is turned OFF but power light is still on.

    Have you installed something 4 days ago? Or deleted some important application?
    Sorry, but it is not easy to say with certainty what the problem is here.

  • Re: Toshiba Tempro does not work

    When I connect Windows 7 on my laptop, I get a dialog message saying that Toshiba Tempro does not work and that Windows is trying to find a solution, although he never does.

    I tried delete, by downloading from the Web from Toshiba site and reinstall it without success.

    Help, please!

    Peter

    Usually reinstalling should help. Remove the Tempro system, clean using CCleaner registry entries, restart the laptop and try to install Tempro again.

    In the worst cases, remove Tempro and the problem is solved. In General, it is a useful tool in Toshiba but in fact you don t he need at all. I removed it from the system. In a first time, it runs in right context and slow down the performance of s for laptop and inform me of updates which are not so important to the functionality of the laptop.

    Perhaps in the future make you clan installation operating system with original Toshiba recovery image and after doing this, you will have clean OS preinstalled with working perfectly Tempro.

    Good bye

  • Pavilion 15-e020tx: does not turn off pc portable hp pavilion 15-e020tx

    Hello.
    I have a pc hp laptop pavilion 15-e020tx. It does not turn off and does not wake up mode 'sleep'...

    I tried to restore my laptop to factory setting, updated everything I can, but it still does not work
    Could someone help me please

    Update the BIOS to the current version. A F.24. The direct link to the download is below.

    http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69897.exe

  • Does not turn my Iphone 6? /

    I own an iPhone 6 and I have for a year now. I turned off my phone a few hours ago and went to turn it back to the and it does not work. The apple logo appears, but the screen turns off after 5 to 10 seconds of the projected apple logo. I tried pressing the two keys and I also tried to connect my phone to itunes but it doesn't connect either.

    Press the sleep/wake and home buttons and keep them for at least 10 seconds.

    If this is not enough, take a look at these articles Support from Apple:

    If your iPhone, iPad or iPod touch does not respond or does not turn on - Apple Support

    Use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

    As a final step, try recovery mode. Turn off your unit, then plug it to your computer with the hold home button. Hold down Home button until you see the logo on the screen of your iPhone iTunes. After that on your computer, you should see the iTunes window saying that your iPhone needs to be restored to factory settings. Click Restore.

    More info here:https://support.apple.com/en-us/HT201263

    If these steps do not work, contact Apple and ask for help.

    https://www.Apple.com/support/iPhone/contact/

  • printer does not turn on

    My Deskjet 6980 printer has stopped working.  It has worked very well so far. Flashing lights said he needs ink. I put in the new ink. Now, it won't turn. The power supply is turned on, the works of output (without surge protector), but the printer does not turn on. In all he has no light on the printer, except light power cord in the back. I tried everything I could find online, but nothing works. My computer was still recording the printer, but since it will not power, says that it is in offline mode. Any suggestions would be helpful.

    The unit may have developed a power failure, but may be also simply in a State of error because of the fresh cartridges.  There are a few steps, I'll try in this case of troubleshooting.

    * If possible, try to remove the cartridges that you recently installed before performing a hard reset of the printer.

    * Hard reset of the printer by unplugging the device, disconnect the other end of the power cord from the wall outlet, separates the power cord of the power supply, wait 30 seconds and plug it back up.

    See also the steps described in the document, found here, to solve a lack of power.  I hope this helps.

  • A Wi - Fi connection does not turn off correctly

    When I turn off Wi - Fi in the quick toggle or settings page it does not turn off and it is left running. (I have not 'analysis always' either) I can see in the graph of the battery when I turn it off for a while it always shows the green bar on Wi - Fi. I had this problem on 5.1 on my 4g (2013) g bike and I don't always.

    This seems to be a matter of google - I have it on non-Moto phones as well. The only thing to do is to restart with the Wifi turned off.

    I don't remember if disable the Wifi in the precision of the GPS solves this problem or not. I decided to live with it for now.

Maybe you are looking for

  • Run Subvi - specific time

    Hello people! I have a generic application that run a timed sequence of loop. Inside the loop, I tried to generate a random number and get him curent date when the number was generated. As you can see, For example: I put the period at 50 ms. In the E

  • Why drives c and d closed c$ and d$ on windows nt server 4

    I have discs on a windows nt Server 4. The first hard drive is partitioned as c and d. The second drive is partitioned as e and f. Why are the drives c and d labeded c$ and d$, and will I have problems if I try to put programs on d$.

  • Black screen with cursor on startup; Could not load safe mode

    Original title: ' black screen of death, white screen, what you want to call different... but then the rest here " I am running Windows Vista Home Edition on a laptop Gateway.  I did have problems with the laptop, or Vista, about 3 years I've owned i

  • How to add or download a slide show on You Tube

    Windows DVD maker How can I move a slide show in windows DVD maker YouTube file?

  • Periodic constant disk activity

    My new 64 bit Windows 7 computer has the annoying problem to access the hard drive in a second apart permanently. Watch resource monitor 'System' service writes to disk to the approximately 10 to 20 KB/s, even if nothing is runnning. Use of CPU is An