Toshiba Equium L40 - 10U Wireless does not

I recently updated my Toshiba Equium L40 - 10U to Service Pack 2 for Vista and now my wireless does not work. I tried to update my driver - but its already been updated, checked for updates - all installed, ensured this driver has been activated. Yet I still can't wireless to work, I don't know what to do now!

I checked my network connections and my wan (PPPOE) miniport is disconnected when you try to connect it comes up with ERROR 815. Then I have to make sure that my internet connection options were correct - do not establish a connection and do not allow the proxy server and still get this message.
My BIN is Realtek RTL8139/810 x Family Fast Ethernet NIC (do not know if this is useful or not) I tried to turn it off then try and turn it back on? But do not know if that would improve the situation or not.

Hello

 
 
(1) do you have made no changes before this problem?
(2) what is the exact error message / complete you receive?
 
Method 1: Follow the steps in the following articles and check if they help.
 
Step 1: Safe mode with networking 
See the link below and check if the problem persists in safe mode with network.
http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
 
Step 2: If the problem does not persist in Mode safe mode with networking, I suggest you to put the computer in clean boot mode and check if it helps.
Clean boot mode
A clean boot to check if startup item or services to third-party application is causing this issue.
Try to install the updates in clean boot mode, and check if the problem still persists.
You can read the following article to configure the computer to boot:
http://support.Microsoft.com/kb/929135
Note: After completing the troubleshooting steps, please refer to clean the start link to set up your computer to normal startup mode.
 
Method 2: Follow the steps in the below items to Disable Antivirus and firewall and check if it helps.
 
Step 2: Turn Windows Firewall on or off

http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off
 
Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
Note: You should not turn off Windows Firewall unless you have another firewall is enabled. Turning off Windows Firewall may make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers.
 
Method 3: Uninstall and reinstall the drivers
 
You can also try uninstalling and reinstalling the drivers who can help you further.
 
Also see the links below for assistance.
Windows wireless and wired network connection problems
List of Error Codes may appear when you try to establish a dial-up connection or a VPN connection in Windows Vista

http://support.Microsoft.com/kb/923944
 
Hope this information helps.

Tags: Windows

Similar Questions

  • Satellite L40 - the Wireless does not connect until svchost has been disabled

    Hello.

    I have a Satellite L40 without BONES, I bought and I installed a XP/SP3. I have a small problem when I connect to my wireless NET. It does not connect until I open the Task Manager and remove one of the two svchost process open with the name 'network service '.

    Someone has an idea of why this never happens and how to fix it (I can opperate thereafter, but is a little annoying to have to do each time).

    Thank you.

    Tried to reinstall the wlan drivers and utilities already? When you do so, you should check the download pages of Toshiba for the latest version of the driver.

    Is the WinXP installation you have performed, had integrated SP3 or SP2? Because I would like to know if wlan worked with SP2.

  • Satellite L40-17 t Wireless does not! Win 7 32 bit

    Hello, my name is Alex. I have a problem with Toshiba L40 - 17 t wireless driver.

    So 3 weeks ago I got windows 7, WiFi worked fine, had no problems with it.
    Recently I reinstalled windows 7, and now my wireless does not work. It is said that no connection is available, even if the distance between my laptop and the router is 10 cm.

    I tried windows 7 driver newest---> does not
    I tried windows vista a newer driver---> does not
    I tried the windows xp compatibility mode---> does not

    Lucky my local network works, and I can't access internet, but I also want to use the Wi - Fi function.

    My wireless card is Realtek RTL8187B.

    I tried the drivers from realtek site too, they are not no longer works.

    However, I remember before you reinstall windows 7, I looked at the version of the driver and its date was around 2008. I have not found all the drivers for Toshiba L40 - 17 t, difficult 2008. I hope someone can help me solve my problem.

    Thanks in advance,
    Alex

    > I tried drivers from realtek site too, they are not no longer works.
    Is this means that wireless network adapter is not installed and recognized properly in the Device Manager?
    In the Manager of devices-> network cards, you should see the wireless network card. If there is no yellow exclamation point and then the wireless network card is installed correctly and that the driver is working

    > I have windows 7 ultimate, wireless worked fine, had no problems with it.
    Recently I reinstalled windows 7, and now my wireless does not work. It is said that no connection is available, even if the distance between my laptop and the router is 10 cm.

    This suggests that there is s configuration problem.

    First of all; Are you sure that the WiFi was enabled? Using FN + F8, you can enable the wireless network adapter. If the FN buttons would not work, then you must install VAP (value added package) and Flash memory card Support utility. If you didn t find these tools in the pilot L40, please check the new generation of portable devices such as L500 or newer.

    On the other hand; are firewalls, antivirus software pre-installed that could affect the connectivity? Check it; I've been reading about similar problems, and finally a firewall (like zonealarm) was the problem!

    Following; Do not forget that you have configured the wireless correctly; use the good encryption and password; for testing purposes, you can disable the security settings on your router and may attempt to connect without the use of encryption.

  • Satellite Pro L40 Wireless does not and wont stop correctly

    Hello
    just got a Satellite Pro L40-15 1 week ago and it's been downhill.

    The Wireless does not work (and yes the switch is activated and drivers installed). Sometimes windows recognizes no device when I boot.

    And when I stopped he said blocking down, but crashes just on this screen.

    Now, I'm an advanced user, so I've tried many things. Can anyone help?

    Thank you

    As a first step, I would recommend to use the Toshiba Recovery CD and renew the operating system.
    Then update the Vista of the State. I mean to install patches and fixes Vista all published.

    Check this thread:
    http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?MessageID=107665

    Here you can see that a missing patches can have a bad influence on the wireless network card and the entire operating system!

    Good luck

  • Need USB drivers for old Equium L40 - 10U PSL41E running Vista 32-bit

    Hi all

    I think that my USB driver is corrupted. I found the ChipSet, LAN and BIOS drivers for my old PSL41E Equium L40 - 10U running Vista 32 bit. However, I have not found the USB drives I need. USB drivers are contained in the ChipSet, BIOS or LAN driver?

    If not, where can I find and download the USB drivers for my old old Equium L40 - 10U PSL41E running Vista 32 bit?

    Thank you! -Le Cannet

    Here is where I found the drivers (but with no mention of USB drivers):
    [Drivers Equium L40 - 10U PSL41E | http://uk.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=UK&selCategory=8 & selFamily = 391 & selSeries = 326 & selProduct = 752 & selSho rtMod = 541 & language = 13 & selOS = 26 & selType = all & yearupl = DST & monthupload = & dayupload = & useDate = null & mode = all Machines & search = & action = search & macId = & country = 8 & pa ge 1 = & startPage = 1 & prevCl = true]

    > Are contained in the ChipSet, BIOS or LAN USB drivers driver?

    USB drivers are part of the Windows operating system.
    The USB ports should work after the installation of the Windows operating system and, therefore, there is no such thing as a USB driver for the USB 2.0 standard.

    In addition, the chipset driver must be installed.

    I checked the proposed link in your ad and here, you can download the Intel chipset utility.
    The update of the BIOS is also available

  • Toshiba Equium L40 10 X Bluetooth stack - evaluation will expire

    Hi all

    Help, please! I tried for centuries get a bluetooth stack that works with all the different devices and programs that I use (I've tried Widcomm IVT, Microsoft,...), but nothing helped. Finally understood that only Toshiba, duh! I have a Toshiba Equium L40-10 x (note this does not come with bluetooth hardware then I use a dongle).

    I installed the Toshiba stack and it's amazing! Everything just works! Bravo Toshiba... just not yet, because even if I'm on a Toshiba laptop (download page of warns him that it only works with Toshiba laptops or it runs out after 30 days), it is still only the trial version and will be completed in a month. Presumabley it's because I have a dongle rather than hardware built-in bluetooth?

    It is, as I am legitimately it runs on a Toshiba laptop, I get the full version, happy to pay I just need to know where!

    If you have something to offer advicewise please do!

    Thank you all,

    Dan

    To be honest, it should works on your Toshiba laptop without limitation in time.
    I tested it with my dongle BT USB Toshiba and everything is OK.

    Try reinstalling the last stack of http://aps2.toshiba-tro.de/bluetooth/?page=download BT

  • Satellite Pro 6100 Wireless does not work after restoring from HARD drive

    After that restore disks for installing a new HD and use and to update XP sp2, the Wireless does not work and if the card is installed XP hangs then works in fits and starts. If the card not in place, not bad at all.

    Booting from a Linux CD, the card works perfectly! I assume that the driver is the problem. The wireless card is the original, an Agere MPC13A-20/R, with Toshiba p/n PA317U-1MPC.

    I have found some drivers Agere, but am not sure

    (1) if they are correct
    (2) how to install since the machine works in a way limited with the card in place.

    Any advice?

    Hello

    I checked the page of the pilot and the only available for Windows XP WLan driver is the driver of v.1.11.108 Agere.

    (1) just try to install this driver. If the driver is not correct or is not compatible, then windows will not install the driver and you will receive a notification. You just have to try

    (2) generally you may reinstall the driver from the Device Manager. Open network controller tree, and then you can reinstall the driver.

    But this is only possible if the windows started successfully

    PS: Have you checked the information of Microsoft Windows XP SP2 update on the page of the Toshiba driver.
    I discovered that you need to update several utilities if you have installed SP2 on this laptop.

  • Tecra A7 - Intel PROSet / Wireless does not respond to the stop

    Hello

    during shutdown of my Tecra A7 the Intel PROSet/Wireless does not react, but must be completed manually.
    The last such Intel driver published by Toshiba download would help solve this problem?

    Thanks in advance for your support!

    Best regards
    ClausP

    Hello Christmas

    You can try to remove Inter PROSet and use the Windows settings for WLAN configuration.

    I don't have this problem, but you can also try installing the latest version of the Toshiba support page.

  • Satellite L500D-163 - Wireless does not

    Laptop: Toshiba Satellite L500D-163 (with card wireless 802.11 b/g/n)
    Router: Pirelli Discus (having support 802.11 b/g).

    Hello

    I bought a portable Toshiba, Satellite L500D-163, two days ago.

    Windows 7 and Ubuntu Linux 10.04, the Wireless does not work. It shows all the available wireless network neighborhood, including mine, but it connects to my network.

    I also have an Acer laptop that connects to my network wireless without problem.

    I placed the Toshiba laptop side by side with my Acer laptop and tried all the options:
    802 11b, 802.11 g - WEP, WPA, WPA2
    with simple passwords of the style: "00000000".

    and SSID wireless to the router changed something as simple as "abcde".
    Computer Acer laptop connected without problem in all cases, but Toshiba didn't connect.

    In Windows 7, the connection information appears as connected but 'Limited' and the software Toshiba says that the laptop is not getting an IP address.

    I manually entered the IP address (192.168.1.2), subnet mask (255.255.255.0) and the default gateway (192.168.1.1 router =) below the configuration in Windows 7 wireless card, but it did not work.

    The laptop must support Toshiba, or y at - it an incompatibility with my router?

    Thank you.

    Great! Thanks for that!

  • Wireless does not work after Windows Update

    Original title: Wi - Fi internet connection is DISABLED since yesterdays upgrade, how can I get that back on?

    Since a windows update yesterday, before closing my laptop... I am not able to access the Internet.

    My without wire is off and I can't turn it back on.  Toshiba wants $99 for technical support.

    Hi Sheryl,

    Please join Microsoft Community where you can find the necessary information on Microsoft products!

    Wireless does not work after a windows update.

    1. what day that was installed?

    You can check the update in the update history:

    See the Windows updates are installed

    http://Windows.Microsoft.com/is-is/Windows7/see-which-Windows-updates-are-installed

    2. do you receive any error messages?

    3. What is the model of the computer?

    The problem may be with the drivers or with the device.

    I suggest that you refer to the procedure described in the site:

    Wireless and wired network problems

    http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

    I hope this helps. If the problem persists, let know us and we would be happy to help you.

  • Toshiba 40 HL 93 R does not remote or and door panel

    Hi all.
    My Toshiba 40 HL 93 R does not remote or and door panel.
    I guess the TV is blocked or immobilized because remote is 100% functional.

    How can I unlock TV? Combination or other. I can't find anything in the manual of the TV

    I put t think that the TV is locked... to my knowledge, it is possible.
    You can block single channels setting a password, but this does not affect other functions of the TV.

    Disconnect the TV from the food sector and wait a little crisper.
    Connect the TV to the network, then press power button to power ON the TV

    It work?
    In case it doesn't, you should contact the service point because it seems that your TV equipment is affected.

  • Pavilion dv7: Wireless does not work after upgrade to Windows 10

    After the upgrade to Windows 10 Wireless does not work, even if the wireless symbol F12 shows blue. In the network settings, the wireless switch exhibits & cannot be turned on to.

    This feature worked perfectly in Windows 7

    No worries.

    Thanks for the actual name of the product from your laptop.

    Let me take a look.

    I will edit this thread to let you know what I found.

    The Intel Centrino Advanced - N 6230 is a wifi adapter that is compatible with your book which has Windows 10 drivers available. the driver is on the following link.

    https://communities.Intel.com/thread/59710?start=0 & tstart = 0

    You can replace yourself because it is easily accessible after removing the cover of the hard drive Bay. See page 21 of the manual at the following ADDRESS.  http://h10032.www1.HP.com/CTG/manual/c02842278

    I saw them on eBay for @ $20.00 USD

    http://www.eBay.com/ITM/new-Intel-Centrino-advanced-N-6230-Wireless-WiFi-Bluetooth-combo-card-62230ANHMW-/170958962681

  • Wireless does not work - Satellite A300 model PSAGCA

    Hello

    My built-in wireless does not work on my laptop. I called the customer service line, his fees to fix the problem but to no avail. Now, I have to use the wireless adapter to use internet which is not the way I wanted to. Can someone help me please how to do my job with built-in wireless?

    Thank you

    adoolan

    + The message was edited: model number added to the object.

    Hello

    Please tell us which laptop model you have and what operating system is preinstalled.

  • Re: Wireless does not work on the Satellite L505-13N Windows7 Professional 64-bit

    Hello

    I just got a Satelite L505-13N and upgrade to Win 7 Professional. The Wireless does not work. It seems that the driver is not yet installed.
    FN + F8, that should give me the option to turn on/off Wireless does nothing and the wireless on the laptop light is lit (orange color).

    What should I do?

    Thank you

    George

    Wait a moment George.
    What do you mean with upgrade? Did you do your own installation of Win7?

  • Toshiba accessibility TACSPROP (Fn keys) does not work on my Satellite A100

    Laptop A100-097

    I am facing a problem with the extraordinary on my keyboard * FN keys * managed by program "* TACSPROP.exe*" which is located in *C:\Programmi\Toshiba\Utilities\.*
    This program does not start automatically at startup and if I manually run his way a window is also come say * "Questo sistema non Può utilizzare Toshiba Accessibility" * (in Italian: "" * cannot use this system Toshiba Accessibily * ' ").

    I can't identify the installation program appropriate for the program in the list of drivers that you provide support download page, but I can tell you that the program is in the same directory where the Software * Hardware Support * is installed.

    Please, can you provide me with the Setup program for this program? I think I'll have to try put it back.
    Is it possible, that it has been marked as a Spyware of Vista or AVG? Maybe some windows update changed something...

    Help, please!

    Thanks in advance

    Hello

    These types of problems are very strange to me, and I wonder why this happen. The fact is that the recovery image (recovery DVD) is very well set up and there is absolutely no problem with the use of the FN keys. All these functions of FN keys are tested and it should work. All the necessary services will begin with OS and you must be able to use all the key functions of the FN.

    I don't want to speculate what the problem is here, but I can't imagine you have this problem on the first day.

    Now the question is: why is that you get? Using the factory preinstalled OS or you have installed your own version of the OS?

Maybe you are looking for