Total radiated power units (PowInfo)

Similar Questions

• If I'm totally off power to my PC, (storm in the region) to reset, the cursor appears, but will not move until I restart again.

  If I just powerdown (overnight), leaving a/c, connected, the cursor appears and moves, as my mouse moves.  HOWEVER, if I powerdown and completely disconnect the PC, 110V, to keep safe from one close shot of lightning, THEN the problem appears.  After the storm passed, I plug the PC into the 110 outlet, turn on the computer and restart it.  The cursor appears in the center of the screen, but it will not move when I move my mouse.  THE ONLY THING I can do is hit briefly, the power button to turn off the back and then click New to reboot (twice now)... then the cursor appears in the center of the screen and moves when I move my mouse.

  Yes, I still think it's the battery.  If the computer is turned off but still plugged into the wall, food always provides a small amount of power to the motherboard to keep a ready"" State.  In fact, if you stop it, but keep it is plugged, you can send a packet to 'Wake-on-LAN' through the Ethernet that would then turn on your computer so you don't have to press any button at all.  This requires that some things are always under tension even when the rest of your computer is turned off.  Remove the plug from the wall removes this standby power and now the BIOS of your motherboard must hold his memory by falling back on the battery.

  HTH,
  JW

• HP media center m7580n power units

  is power in this computer, hp m7580n Center media, it is proprieitary... or can I install a regular atx PSU in it?

  Ronss, no, it's not owner.  The best way to know if the standard ATX PSU will fit is to measure the existing PSU.  Find a new power supply that you like and that you access the manufacturer's Web site to compare the measures.

  Would what power you buy?

  Here are two brands of high quality who will do a good job:

  http://www.Newegg.com/product/product.aspx?item=N82E16817139008

  http://www.Newegg.com/product/product.aspx?item=N82E16817341001

  I had the GXS OCZ 600W in my computer until I upgraded.  It's a great PSU.

• BlackBerry Smartphones get video off the POWER unit to the PC? 3GPP to other formats?

  This shouldn't be so hard...  I have a few videos of the devcie I want to transfer them to the hard drive on my PC.  I used the Desktop Manager and when I choose MY MEDIA a Roxio application is launched.  I moved the video of the MY DEVICE to MYMEDIA but which does not actually change the video files on the hard drive.  I did eventually fined the files in a folder MY PICTURES/DEVICES DOWNLOAD but they are in a format that none of my video editing software will import.  So, is there an easier way to import media and it can be saved in one format other than the 3GPP format?

  On your media card, allow the mass storage and move the files of your press simply pass through "My Computer" on your PC when connected via USB.

  See details here:

  http://www.BlackBerryFAQ.com/index.php/How_do_I_add_media_files_to_my_microSD_card%3F

  3gp format is playable in several media players of PC, I think that Quicktime is one. Just use a video converter to transfer in the format you prefer.

• New power supply for w510 to the United Kingdom

  Hello

  I just broke the pins on my diet revolving around the connector, so it snaps correctly and now my power supply is broken, not having is not a standard power unit that I seem to be a little drunk as there is no readily available alternative.

  Shop Acer doesn't seem to work so can't get there guess that will teach me to go against the tide and buying a less known brand.

  Any ideas where I can source one to the United Kingdom? The right pain as if I wanted to take away on vacation next week.

  See you soon

  Sandy

  It's a little a problem, I think that for my own problem that the PSU is fine and just the casing broke I will either make a new door, or actually even easier to buy a charger iconia 18w of another model and transplant the inner workings and the connector.

• Aurora r5 stock heatsync voltage problems with evga modular 750 watt power supply

  The stock fan on the heat sink thermal condition of the R5 Aurora stock runs just as fast as it can while holding a 6700 k, you mind, at a steady temperature around 30 C idle. Previous the cpu and psu were almost silent, whereas now the fan seems to run to rpm max powered an EVGA 750 watt p2 modular power unit cpu1 slot. How can I reach the bios to lower the fan speed?

  Yet, I am not "awake" not until the Caffè Verona + mix roast French kick. I do not have the model of your computer, but your service PDF manual available for download on the R5 Dell.com support page lists the Bios options, lists the right place to connect the fan to & lists the keyboard button to push to enter the Menu of the Bios. At a time like this, I could put back the original power supply in there, confirm the fan installs, if so, replace the new power supply in, see if again deploys spazzes

  but I don't think it's the power supply

  If your bios menu has no control of the fan speed, a swap of psu se do not spin faster or slower radiator fan. If you have ordered the 6700 k to the Fund, you would have power 850w. If you have installed the 6700 k yourself, using pneumatic radiator, it is possible the 95 watt cpu needs best, as the cooling liquid cooling. I see you're at 30 c idle, but it seems that the fan is bad fan... header check than 1st, see options in photo here: Alienware Aurora R5 - fan CPU 100%

  • Edit: @Hockeytown messaged me: "I eventually replaced the H80i Corsair GT for a 550LC Asetek ebay OEM pump. "This has solved my problem of fan and I am now able to connect via the (Top_fan + Pump_fan) factory setting and not errors.
  • @Hotarri installed Corsair H60

  It is possible, the motherboard as expected 'react' different when deleting in the 6700 k; It is possible that since 6700 k factory liquid cooled, the spazzes motherboard when the owner puts 6700 k themselves but without cooling liquid, such as a small problem, uses one table different fan / or a set of parameters of the fan speed (6700 k + pneumatic radiator = incompatibility) that hopefully you can change in the Bios somehow somewhere but maybe not

  It is possible that you can hand-place 3rd fan header 'pump', trying to fool the mother board, lol, see if the cpu fan slows down as a test. Still, I do not have this model, I think that the motherboard that waits for a signal fan/tachometer on the header of the pump in response to 6700 k, good luck with it

  post a photo of your swap 750 for us when you get it figured out (=

• NB200 122 - loading using the battery power options

  Dear all

  I recently bought a Toshiba NB 200-122 Mini Netbook, I tried to use all the power options (full power)... always shows 15% battery (charge) even if I kept it charging for a day in hibernation mode... (when connected to the power unit).

  Other laptops would be fully load 100% when it is connected to the unit of power for one day...

  Why the netbook battery is slow or not clean load?...
  Or other options with her... Or having to drain the battery completely and use it...

  Could someone suggest me some advice about this...

  Thank you

  regards Sarah

  Hi Sarah,.

  I agree with the user above. You should try a BIOS update you can find the Toshiba site. Before applying it, close all programs running also your antivirus and firewall and make sure that you are logged on as administrator.

  In the worst case you battery is damaged or some cells in it. You can get a spare to an authorized service provider.

• Qosmio G50 from power (PQG55A-024020) - on board the Board of Directors

  Computer age subject to 18 months starts giving various indications of power supply 3 Aug. DC In light flashing, battery load sometimes and sometimes not, would be put off, computer doesn't end not a boot on the power supply with battery removed.

  Computer limped along for 8 days then failures stabilized. DC in stationary light on plug, battery indicator is "0% load, no charging current". Battery should have about 70% fresh and computer boots properly on the battery. I guess that the on-board power unit is u/s.

  Any comments or advice appreciated. I am currently in journey to the center of the Australia.

  Thank you, David.

  Hello

  If you have an adapter that you can test or a friend, maybe you should do this, otherwise I think that it s mainboard malfunction or something else controls the process of loading. In this case you need professional help form an ASP to get rid of it.

• Power supply question

  Hello

  I have an old y580 and love it! I've been running it since its release date. Unfortunately, my diet started to wear off and the cord pulled out of the unity of the adapter. Needless to say that Lenovo does not sell these power units and the liteon and delta recommend supistutes sells... in my research online, I came across "y580 feeds" but I noticed that they to 19 v not 19.5 and 6.3 No 6.15.

  I was wondering if anyone has experience with this and knows if it of a big problem or will do the trick without limiting performance or damagaging my y580. Thank you!

  It shouldn't with this difference.5. The laptop works at the voltage of the battery. The current capacity is larger and its fine. Polarity and the connector must be the correct type!

• Satellite P10-304 power until now

  Hello

  Got the machine Satellite P10-304, which won't turn on after the 2nd attempt. What happened: -.

  Machine power of cold - booted Windows XP ok start. After 5-10 minutes, the machine screen is dimmed (resembles backlight is gone) and couldn't turn off the machine by pressing button, so had to remove the battery to kill machine power.

  Now machine won't turn on (same battery fully charged), when I pressed the power button, I get a light flashed orange once inside the circle of blue light around power button / stop.
  Leave the machine shut down for about an hour and machine started in the BIOS screen, then after 3 minutes the screen is dimmed. Machine unbootable. Checked AC adapter and get 19.3Volts and 6.1Amp for power unit ok.

  Looks like the motherboard plays up and needs to be replaced? Dose - that someone has encountered this problem before?

  Thank you very much

  Hello

  > Sounds like the motherboard plays up and needs to be replaced?
  Yes, it seems so :(

  Maybe it s not the motherboard, but another part of the material. But to be honest, you should go to an authorized service provider. Technicians can check the laptop to determine what the problem is exactly.
  And here, you can search the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Welcome them

• Power supply helps.

  HI, I am looking to update my video card on my hp pavilion p7-1003w,

  My specs are:

  AMD Athlon II X 4 650: 3.2 ghz

  8 GB of ram

  250W PSU

  Motherboard for N-Alvorix-RS880-formfat (Alvorix) .
  Windows 7 64-bit,

  ATI Radeon 4200

  But I met some power problems with my motherboard.

  When I plug in a new power supply they have NEVER the '4' 'pu521' adaptor for my motherboard.

  http://oi39.Tinypic.com/206dmcp.jpg

  my new graphics card is a "Radeon HD 6670'

  If someone could tell me a sufficient power supply, that would be great,

  -Conner

  Conner wrote: thank you very much Hanspuppa! But when you say "I would recommend staying away from these power units more low cost. Many of them will be list a higher rating that they provide actually. "You mean that I should stay away from the"Antec 550 watt power supply"because it seems that it would work for my computer and I want to take a professional Word for it. -Conner

  Hello Conner, I'm not a professional at all, not even close. I have 25 years and more cheating on her with these machines, perhaps a professional fool to fool with these machines. but we all need something to do in life.

  The Antec, Corsair, OCZ and a few other feeds are very good quality power supplies.

  When I suggested to stay away the lower cost ones, I meant those that cost like $19.99 - $29.99 or other similar costs in this range. There are a few low-cost power supplies out there who have some good reviews, but food is the most important in a computer, since everything in the computer runs power off from the power supply.

  I always look at the reviews of others to get an idea of what other people have to say and the Antec page linked to over 500 positive feedback. It is a very unusual number, almost everyone who bought this power supply was happy with it.

  I used the Antec years products and have never had a problem with their products.

• Location entered power in bulk / HP DV7-3065dx / generic DV7 - Laptop!

  Hello I could you use quick help!

  My laptop got sat on the cord into the laptop to charge!

  The laptop has always worked and fresh but the inner part where the cord plugges is loose now!

  Can I put a tape around the site to fix?

  Otherwise, I think I have to disassemble the entire and re - attach the power unit inside.

  Any help would be appreciated!

  Thanks for the info. KOM!

  I'll talk about Verizon or AT & t unless you know a better carrier ~ ~ T-Moble? ~

  I was wonderong just if there was a way to eliminate the use of a cell phone all together?

  The telephone companies charge plus $40-60 a month and I don't know would be the cheapest way!

  Thank you!

• Workstation Dell Precision T7400 will not power with ATI Radeon 5970 installed

  Hello

  I had my dream, the monster bi - GPU ATI Radeon 5970 video card and installed in my T7400 but the system will not start, all I get is a fast fan rotation and a kind of sounds from food, a bit like "Brrrnt, click on" led me to believe that the power supply could not handle my video card.

  The video card requires an 8pin and 6-pin power plug. When I plug the 8-pin and 6-pin and turn on the computer, is a no-go as shown above. When only the power plug 6-pin I plugged the PC sounds like it will start, the power of fans but no display as I expect.

  I tried this video card into the two PCI-Express slots with the same failure as a result. The computer works fine with the Nvidia Quadro 3700 in it... using a 6 power connector pins.

  I got the ATI Radeon HD 5970 video card in a store of the local computer and it had tested ($15) because I didn't test it in a spare computer and video card passed with flying colors...

  That's why I thought my 1000 Watt power supply was a problem, so as a bet, I ordered a replacement off eBay and received a sweater to work more the wiring harness and completely replaced the two who has a job to say the least! Have you tried to replace the wire bundle? a lot of work...

  I got it all back together, crossed my fingers and prayed and tried again and the same thing... NO LUCK... I put the graphic card Nvidia Quadro 3700 back in and the system of power like a charm.

  What on earth could it be the cause for it? I REALLY want to get this video card works in this system.

  I even tried a bios update and carefully watched the card mother and everything that I could to see if there's... nothing exploded capacitors...

  Please HELP - I want to get my game...

  Wesley

  I think I found the solution and I would like to mention it here to help others if they get him...

  A: the power of Dell for the T7400 was designed to produce five rails 12 volts @ 18 AMPS each and the video card requires approximately 45 to 50 amps to work properly. Video cables (one with a 8 pin) and 6-pin on the harness even seems to only provide amps 18 or more and the computer will not power because power protection circuit sees too many amps being requested by a 'rail' and turns off immediately...

  I went to electronics of FRY in San Jose and bought a few cards that helped divide the current between different sources, such as the cables of the hard drive and video.

  B: I have a small battery backup power unit and my T7400 was plugged into the saved game... When I got the video card to work, he could make a beep loud and after minutes cutting my T7400 due to the mainstream power support... I plugged the computer into a 'surge protector' but not battery backed up to the slot and since then had no problems...

  Now after several tests including FurMark, my graphics card stress works very well in this system... This is due to an unfortunate design in the T7400 power supply and wiring... Now that I have this solved, I hope that someone else can benefit...

  Get an adapter like this one, it allows to separate the power sources for the 8 power connector pin and use the PIN 6 original which is connected to the Dell printer condition 8 pin adapter, for the 6-pin slot... hope that makes sense... by trial and error, you got it right!

  I had one like this:

• SG300 - 28 p: POE power drops every few minutes

  Hi all

  We have a SG300 - 28 p which, at intervals between 5 and 30 minutes or more, lower power to all its ports POE-powered and then immediately restores power. Switch logs nothing when this happens other than to record that the ports went down and back up, even with debug logging enabled. Non - POE ports are not affected.

  When the problem started there were only four POE devices on the switch and we are far under our power budget. (During the test, I added a fifth device, see below.)

  Not all combinations of devices cause the drops occur - specifically, it seems that having devices on ports next to each other causing the drops. When the drops occur, absent the increment of POE devices all counters. I noticed this thread earlier here seemed similar:

  https://supportforums.Cisco.com/thread/2165089

  but in this case, he got no power at all in the adjacent configurations, instead of having to drop all the several minutes.

  I am running

  SW06 #sh worm

  SW version 1.1.2.0 (November 12, 2011 time 23:34:26)

  Start the 1.1.0.6 version (date may 11, 2011 time 18:31)

  HW version V02

  I have the 1.2.2.7.6 ready to go new firmware, I will update this when I get a chance to test it. Unfortunately, it's a switch of production, but it's a with relatively few devices to it so far. If need be, I have a sf300 - 48P I can exchange this sg300 ENJOI trials.

  Thank you for anything you might suggest.

  Here are the details:

  -' Phone' is a phone to IP Avaya 4610SW or 5610SW (class 2)

  -"Watchdog" is an environmental monitor IT Watchdogs Watchdog 100 (class 0)

  -"WAP" is a Cisco WAP4410N (class 3)

  All initially due to lack of combination:

  GI10 phone #1

  gi22 phone #2

  dog guard gi23

  WAP gi24

  would result in the POE power to place on all ports, every 5 to 30 minutes.

  I disabled Green Ethernet completely - no change.

  And then made the following tests:

  1. "power never inline" on gi23 and gi24: problem disappeared

  2. 'inline power auto"on gi23 and gi24: problem is back

  3 ' power inline never' on gi23 only: problem disappeared

  4 ' auto of inline power' on gi23: problem is back

  5 ' power inline never' on gi24 only: problem disappeared

  6. "power inline auto" on gi24: problem is back.

  I left gi23 powered throughout the night and it was stable: it's about 10 hours without any problem.

  This morning, tried the following configs:

  08:54 - worked fine

  IG4 watchdog

  GI10 phone #1

  gi22 phone #2

  WAP gi24

  10:31 - added another phone, the problem came back

  IG4 watchdog

  GI10 phone #1

  gi22 phone #2

  gi23 phone #3

  WAP gi24

  10:43 - inappropriate phone #3 to IG11 (next) - problem continues

  IG4 watchdog

  GI10 phone #1

  IG11 phone #3

  gi22 phone #2

  WAP gi24

  11:00 - moved phone #3 to gi8 - suite problem

  IG4 watchdog

  gi8 phone #3

  GI10 phone #1

  gi22 phone #2

  WAP gi24

  11:31 - moved phone #3 article IG 14 - the problem disappeared

  IG4 watchdog

  GI10 phone #1

  Article IG 14 phone #3

  gi22 phone #2

  WAP gi24

  and that's where we left things now are stable for about four hours.

  The following products are the config more later (11:31).

  SW06 #show power inline

  Power-limit based port mode

  Nominal consumed power unit power use threshold traps

  ---- ------- ------------- ------------------ --------------- ---------

  1 of 180 Watts 18 Watts (10%)         Disable 95

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  Article IG1 Auto search low class0

  IG2 Auto search low class0

  IG3 Auto search low class0

  IG4 Auto on low class0

  IG5 Auto search low class0

  GI6 Auto search low class0

  gi7 Auto search low class0

  gi8 Auto search low class0

  gi9 Auto search low class0

  GI10 Auto on low 2

  IG11 Auto search low class0

  gi12 Auto search low class0

  ig13 Auto search low class0

  IG 14 Auto article on low 2

  gi15 Auto search low class0

  gi16 research Auto low class0

  IG17 Auto search low class0

  gi18 Auto search low class0

  IG19 Auto search low class0

  IG20 Auto search low class0

  IG21 Auto search low class0

  gi22 Auto on low 2

  gi23 research Auto low class0

  gi24 - Auto on low class3

  -watchdog:

  SW06 #show power inline IG4

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  IG4 Auto on low class0

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Absent of meter: 4

  Invalid Signature counter: 0

  SW06 #show interfaces announce IG4

  Port: IG4

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  -Phone:

  #show power inline gi10 SW06

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  GI10 Auto on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 465

  Invalid Signature counter: 0

  #show int adv gi10 SW06

  Port: gi10

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  -Phone:

  SW06 #show power inline article IG 14

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  IG 14 Auto article on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Absent against: 0

  Invalid Signature counter: 0

  SW06 #show int adv article IG 14

  Port: article IG 14

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  SW06 #.

  -Phone:

  #show power inline gi22 SW06

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi22 Auto on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 591

  Invalid Signature counter: 166

  #show int adv gi22 SW06

  Port: gi22

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  --also was the watchdog, now empty:

  SW06 #show power inline gi23

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi23 research Auto low class0

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is disabled - detection is in progress

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 587

  Invalid Signature counter: 0

  -wap:

  SW06 #show power inline gi24

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi24 - Auto on low class3

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 607

  Invalid Signature counter: 3

  SW06 #show int adv gi24

  Port: gi24

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no yes no no no

  Resolution of priority - Yes-

  Other useful bits:

  SW06 active spanning tree #show

  Spanning tree disabled mode (floods BPDU) RSTP

  By default port cost method: long

  SW06 #sh worm

  SW version 1.1.2.0 (November 12, 2011 time 23:34:26)

  Start the 1.1.0.6 version (date may 11, 2011 time 18:31)

  HW version V02

  Hi Rich, reference this photo I just drew is a rough interpretation of how a switch 24 ports has guts. Each + block represents a processor. The numbers below represent the port Bank that corresponds to the transformer. Of course, MODULE POE is clearly identified. Each module 12 POE ports for services.

  I think you have a completely different question. If the POE works for 5 to 30 minutes, it can be a problem of layer 1 (bad son) or a different, perhaps material condition being disturbed. If the switch is at fault, it seems more likely to be defective to a unit of buggy.  I did a lot of research on the operation of the switch ASIC, transformer and modules of POE in the cohesion.

  Quite frankly, I think you should go to the 1.2.7.76 firmware, factory reset the device and test all the ports you want using the same equipment. If maintaining the POE fall every 5 to 30 minutes and you are absolutely positive, that it is not a question of layer 1 or a configuration problem on your products, can I just replace the switch.

  

  -Tom
  Please evaluate the useful messages

• Add card Gigabyte GTX770 to 500-205 a PC HP

  Hello

  I have aHP Pavilion 500-205 a and I try to put it in a Gigabyte GV-N770OC-4GD, GeForce GTX 770.

  The card says that power must be 600W for the card. Currently, the PC power is 300W

  Then it would be beneficial getting a 1000W power to cover both PC and graphics card?

  If so, it would be my next issues

  1. What power? Any recommendations?
  2. Is this one that I could replace the current 300W one in the same space? I noticed 1000W power supplies appear to be more large size.
  3. Is there anything else I should look out for? I noticed some people saying that I should also remove previous graphics card software. Then, there are the number of PCIE connections... etc.

  Initially, I wanted to just a PC Whiz-Bang with a grunty graphics card. I did not know that I have to start playing with the purchase of gear to get it all to work.

  A few material technicians help would be much appreciated.

  More information you need, just ask.

  Peter

  Peter, welcome to the forum.

  The length of the card is 11,49 ".  I don't think that it will not go in the space provided.  I suggest to make a model of the size of the map.  You must add at least one inch to two PCIe power connectors required by the card.

  I'll answer your questions, but because the card does not, it is for learning purposes.

  (1) the map itself would not need of 600W.  It is total system power requirements.  You could get by with a 700W/750W power supply unit (PSU).  That would give you a lot of reserve.  I love Corsair products.  This is a power supplythat would work for the card.  It is modular, so you should only use the cables needed.  This is the standard ATX.  I always recommend measuring the current PSU and comparing measures to whichever you choose.

  (2) see point #1.

  (3) the computer has full UEFI.  It's software that replaces the traditional BIOS.  It is not said in explaining that I have provided, but HP is one of the leading companies in the development of UEFI.  The card you choose must be compatible UEFI.  To do this, the card manufacturer to provide a video BIOS that are compatible with the computer UEFI.  The power supply in the link has 4-6 + 2 PCIe power connectors.

  If you have any other questions, please let us know.

  Please, click on "Thumbs Up +" if I helped you and click "Accept as Solution" If your problem is resolved.