Tracert ASA 5510

need help on getting tracert to work via ASA5510. I encouraged time exceeded packets in and this method worked on PIX6.x (x) but not on this platform.

ASDM launcher also throw error "Creation of the VM has no" everyone has work?

I have not worked with the ASA again, but on the PIX Version 7, to allow traceroute work, we must add the following lines:

--> Policy-map global_policy

--> class inspection_default

--> inspect icmp error

--> write mem

I hope it works for you.

(Not sure about the ASDM, I'll try to find more information on this)

Tags: Cisco Security

Similar Questions

  • IPS in ASA 5510 killing upload speed

    I've recently updated by a circuit of ethernet metro 20 MB for a 100 Mb connection.  My ASA 5510 severely limits the my download speed.  I narrowed down it to the IPS module.  If I stop to send traffic to the IPS, I get speeds of download between 50-85 Mbps.  If I start sending through again, my download speeds are between 3-7 Mbps.  In both cases, my speeds range between 70-92 MB/s, so it's really affecting only my upload speed.  Is there anything I can do for my traffic IPS, so I can still use my modules and still take advantage of the speed upload huge we pay for?

    Here is some info from my ASA:

    I am matching all traffic:

    allow traffic_for_ips to access extensive ip list a whole

    Here is my policy and class parameters:

    class-map inspection_default
    match default-inspection-traffic
    class-map-botnet-DNS
    match eq field udp port
    class-map ips_class_map
    corresponds to the traffic_for_ips access list
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the ftp
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    inspect the preset_dns_map dns
    class ips_class_map
    IPS inline help
    botnet-policy policy-map
    botnet-DNS class
    inspect the snoop-filter-dynamic dns
    !
    global service-policy global_policy
    service-policy botnet-policy to the outside interface

    If anyone has any ideas, I'd love to hear them.  Thank you.

    Created: May 13, 2011 18:49 created by: Chevrel, customer Aastha(AACHAUDH,265429) was experiencing slow download speeds (3-7 Mbps) on in ASA 5510 IPS module. Download the range of speeds between 70-92 MB/s

    Used the workaround for the bug No. CSCsv69844 , i.e. to set the depth of Regex to 800000 (Please note that this workaround should not serve with the recommendation and approval of the ATC.)

  • Updated AIP-SSM-10 on ASA 5510

    Hello

    I want to upgrade the IPS module in an ASA 5510, and I have a few questions. The AIP - SSM is running E3 479.0 1.0000 and I have a valid account of the ORC etc for this.

    1. What is the version of the software on the question of the ASA?
    2. When I look in the software downloads< ips="" there="" are="" .pkg="" and="" .img="" files.="" i="" want="" to="" upgrade="" to="" 6.3(3)e4.="" do="" i="" have="" to="" re-image="" the="" ips="">
    3. AFAIK redefinition to wipe the device so I just reload the config after, right?
    4. I guess I can apply any update after going to E4?
    5. Can you give me links for this upgrade?

    see you soon

    Let me give some clarification on a few points:

    2. There is no need to recreate the image on the device using the .img file.  You can improve the mechanism of maintenance of your existing configuration using the .pkg file.  It is the recommended method for upgrading to Cisco IPS devices/modules.  The .img file to recreate the image should only be used to restore the default device.

    5 here are links for the upgrade of the probe using a .pkg file.  For updates through the IDM user interface:

    http://www.Cisco.com/en/us/docs/security/IPS/6.2/configuration/guide/IDM/idm_sensor_management.html#wp2126670

    For upgrades via the CLI:

    http://www.Cisco.com/en/us/docs/security/IPS/6.2/configuration/guide/CLI/cli_system_images.html#wp1142504

    Another point of clarification; current releases of IPS software supported on the AIP-SSM-10 are (taking into account you are currently running 6.2 (1) E3):

    6.2 (3) E4

    7.0 (4) E4

    You can go directly to each output.

    Scott

  • Review of the ASA 5510 Config

    Hi all, I'm about to replace an existing a new ASA 5510 firewall.  The environment is pretty simple, just an external and internal interface.  I put in correspondence configs as much as possible, but I'd like to see if there are obvious problems.  I am concerned mainly with my NAT statements.  Nothing in the following config (sterilized) seems out of place?  Thank you!!

    ------------------------------------------------------------

    ASA 4,0000 Version 5

    !

    ciscoasa hostname

    enable the encrypted password xxxxxxxxxx

    XXXXXXXXXX encrypted passwd

    names of

    !

    interface Ethernet0/0

    nameif outside

    security-level 0

    IP 40.100.2.2 255.255.255.252

    !

    interface Ethernet0/1

    nameif inside

    security-level 100

    IP 10.30.0.100 255.255.255.0

    !

    interface Ethernet0/2

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Ethernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    Shutdown

    nameif management

    security-level 100

    IP 192.168.1.1 255.255.255.0

    management only

    !

    boot system Disk0: / asa844-5 - k8.bin

    passive FTP mode

    permit same-security-traffic inter-interface

    network of the 10.10.0.78 object

    Home 10.10.0.78

    Nospam description

    network of the 10.10.0.39 object

    Home 10.10.0.39

    Description exch

    network of the 55.100.20.109 object

    Home 55.100.20.109

    Description mail.oursite.com

    network of the 10.10.0.156 object

    Home 10.10.0.156

    Description

    www.oursite.com-Internal

    network of the 55.100.20.101 object

    Home 55.100.20.101

    Description

    www.oursite.com-External

    network of the 10.10.0.155 object

    Home 10.10.0.155

    Ftp description

    network of the 10.10.0.190 object

    Home 10.10.0.190

    farm www Description

    network of the 10.10.0.191 object

    Home 10.10.0.191

    farm svc Description

    network of the 10.10.0.28 object

    Home 10.10.0.28

    Vpn description

    network of the 10.10.0.57 object

    Home 10.10.0.57

    Description cust.oursite.com

    network of the 10.10.0.66 object

    Home 10.10.0.66

    Description spoint.oursite.com

    network of the 55.100.20.102 object

    Home 55.100.20.102

    Description cust.oursite.com

    network of the 55.100.20.103 object

    Home 55.100.20.103

    Ftp description

    network of the 55.100.20.104 object

    Home 55.100.20.104

    Vpn description

    network of the 55.100.20.105 object

    Home 55.100.20.105

    app www description

    network of the 55.100.20.106 object

    Home 55.100.20.106

    app svc description

    network of the 55.100.20.107 object

    Home 55.100.20.107

    Description spoint.oursite.com

    network of the 55.100.20.108 object

    Home 55.100.20.108

    Description exchange.oursite.com

    ICMP-type of object-group DM_INLINE_ICMP_1

    response to echo ICMP-object

    ICMP-object has exceeded the time

    ICMP-unreachable object

    Exchange_Inbound tcp service object-group

    EQ port 587 object

    port-object eq 993

    port-object eq www

    EQ object of the https port

    port-object eq imap4

    DM_INLINE_TCP_1 tcp service object-group

    port-object eq www

    EQ object of the https port

    object-group service DM_INLINE_SERVICE_1

    will the service object

    the purpose of the tcp destination eq pptp service

    the DM_INLINE_NETWORK_1 object-group network

    network-object, object 10.10.0.190

    network-object, object 10.10.0.191

    the DM_INLINE_NETWORK_2 object-group network

    network-object, object 10.10.0.156

    network-object, object 10.10.0.57

    DM_INLINE_TCP_2 tcp service object-group

    port-object eq www

    EQ object of the https port

    object-group service sharepoint tcp

    port-object eq 9255

    port-object eq www

    EQ object of the https port

    outside_access_in list extended access permit icmp any any DM_INLINE_ICMP_1 object-group

    outside_access_in list extended access permit tcp any object 10.10.0.78 eq smtp

    outside_access_in list extended access permit tcp any object object 10.10.0.39 - Exchange_Inbound group

    outside_access_in list extended access permit tcp any object-group DM_INLINE_NETWORK_2-group of objects DM_INLINE_TCP_1

    outside_access_in list extended access permit tcp any object 10.10.0.155 eq ftp

    outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_1 any object 10.10.0.28

    outside_access_in list extended access permit tcp any object-group DM_INLINE_NETWORK_1-group of objects DM_INLINE_TCP_2

    outside_access_in list extended access permit tcp any object 10.10.0.66 object-group Sharepoint

    pager lines 24

    Enable logging

    asdm of logging of information

    Outside 1500 MTU

    Within 1500 MTU

    management of MTU 1500

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm-649 - 103.bin

    don't allow no asdm history

    ARP timeout 14400

    no permit-nonconnected arp

    NAT (exterior, Interior) static source everything any static destination 55.100.20.109 10.10.0.78

    NAT (exterior, Interior) static source everything any static destination 55.100.20.108 one-way 10.10.0.39

    NAT (inside, outside) static source 10.10.0.39 one-way 55.100.20.109

    NAT (exterior, Interior) static source everything any static destination 55.100.20.101 10.10.0.156

    NAT (exterior, Interior) static source everything any static destination 55.100.20.102 10.10.0.57

    NAT (exterior, Interior) static source everything any static destination 55.100.20.103 10.10.0.155

    NAT (exterior, Interior) static source everything any static destination 55.100.20.104 10.10.0.28

    NAT (exterior, Interior) static source everything any static destination 55.100.20.105 10.10.0.190

    NAT (exterior, Interior) static source everything any static destination 55.100.20.106 10.10.0.191

    NAT (exterior, Interior) static source everything any static destination 55.100.20.107 10.10.0.66

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 40.100.2.1 1

    Route inside 10.10.0.0 255.255.255.0 10.30.0.1 1

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL

    Enable http server

    http 192.168.1.0 255.255.255.0 management

    http 10.10.0.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Telnet timeout 5

    SSH 10.10.0.0 255.255.255.0 inside

    SSH timeout 5

    SSH group dh-Group1-sha1 key exchange

    Console timeout 0

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    source of NTP server outside xxxxxxxxxx

    WebVPN

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    inspect the pptp

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:40cee3a773d380834b10195ffc63a02f

    : end

    Hello

    You do nat (exterior, Interior), I'm going to do inside, outside but the configuration is always good.

    The ACL configuration is fine, Nat is fine, so you should have problems,

    Kind regards

    Julio

  • Cisco ASA 5510 + license + AIP - SSM

    Hello.

    I have this box.

    I have a few questions about it.

    (1) I'll be able to update the firmware (from 8.2 to 8.3 or greater for example) without smarnet for ASA 5510? And what can not do without smartnet?

    (2) I have only AIP-SSM-10 module this ASA 5510. is there a smartnet, too? And when I buy only one module is it build in a subscription for 1 year for the signatures of the IPS?

    (3) if I have the Cisco ASA 5510 base license, my IPS on AIP-SSM-10 will work?

    (4) as I foresee in a purchase of the year a 5510 more with the same module and mount ther of failover. I really need license Security more than failover (active / standby)? For active/active, I know I need one, Yes?

    Please help me.

    (1) you must Smartnet in order to download the software from the download from cisco.com site.

    (2) Yes, there is also a smartnet for the AIP module. Module AIP does not come with one year subscription, but you can ask for a demo license.

    (3) Yes, the basic license is OK for the AIP module.

    (4) Yes, you would need license security more on the two ASA to be able to run any type of failover on ASA5510.

    Hope that answers your questions.

  • ASA 5510 - display block URL Page

    Dear,

    I have Cisco ASA 5510, I have already configured Block_Sites using regular expressions and it works fine. I need to display a Page blocked for any one trying to access blocked sites. Example: I need to display page contains our company Logo and less it shows that "the Site is blocked.

    I can do it on Cisco ASA 5510?

    Thank you

    No, the ASA alone cannot do. To do this, you need a will end UP with appropriate license or a proxy (such as the WSA).

  • Allow specific access through the Interfaces ASA 5510

    Hi all

    In my quest to learn Cisco IOS and devices, I need help in smoothing traffic, or access lists, allowing traffic between internal interfaces on the SAA specifically.

    I have an ASA 5510:

    WAN/LAN/DMZ ports labled E0/0 (LAN), E0/1 (WAN), E0/2 (DMZ).

    Connected to the port E0/0 is a 2811 router

    Connected to the port E0/1 is the (external) Internet

    Connected to the port E0/2 is a 2821

    (I'll add a 3745 for VOIP) port E0/3, but it has not yet happened.

    I want to allow traffic between the 2821 and the 2811 routers so that devices on the networks behind them can talk to each other.

    I've specified specific subnets between the ASA and the routers because I want to learn how to shape traffic behind routers, as well as on the ASA. So behind the routers I have different VLANS, but I'm not restrict access between them, still, at least I don't think I am. But as it is, behind the 2821 devices cannot access the DNS / DOMAIN SERVER that is located behind the 2811. Right now I have the routers DHCP power, who works there. Currently devices behind the router 2821-3560 switch cannot access the domain server, primary dns server.

    How can I set the ASA to allow traffic to flow between the two routers and their VLANS?

    Here's the configs of each device and I have also included my switch configs, incase something should be set on them. I only removed the passwords and the parts of the external IP address. I appreciate the help in which States to create and on which devices.

    I think it is best that I put the links to the files of text here.

    Thank you!

    You must remove the following statements on the two routers:
    -# ip nat inside source... overload
    -for each # ip nat inside/outside interface, if they have configured.

    Remove ads rip of the networks that are not directly connected:
    -2821: 172.16.0.0, 192.168.1.0, 199.195.xxx.0
    -2811: 199.195.xxx.0
    -ASA: 128.0.0.0

    No way should be added to the routers, since he is the one by default, put in scene to ASA.

    Check the tables of routing on routers and the ASA.

    On ASA:

    -Remove:
    object-group network # PAT - SOURCE
    # nat (indoor, outdoor) automatic interface after PAT-SOURCE dynamic source

    -create objects of the networks behind the LAN router and enable dynamic NAT:
    network object #.
    subnet
    NAT (inside, outside) dynamic interface

    -review remains NAT rules.

    -to set/adjust the lists access penetration on the interfaces. Do not forget to allow the rip on the LAN and DMZ interfaces.

    -Disable rip on the outside interface.

  • How many interfaces in asa 5510

    can someone pls tell me how many interfaces in asa 5510.and we can add more interfaces to it.

    concerning

    Assane

    Hi assane,.

    When you order the ASA5510, you can choose between (option Setup/Noo-Noo fixed to add more ports interface):

    1 ASA5510 device comes with 3 x FastEthernet, more 1xmanagement port (FastEthernet)

    ASA5510-BUN-K9: Cisco ASA 5510 Firewall Edition includes 3 Fast Ethernet interfaces, 250 peers IPSec VPN, SSL VPN 2 peers 3DES/AES license, or

    2 ASA5510 comes with 5xFastEthernet, most 1xmanagement port (FastEthernet).

    Cisco ASA 5510 Security Plus Firewall Edition includes 5 interfaces Fast Ethernet, 250 VPN IPSec peers, 2 peers of SSL VPN, high availability active / standby, 3DES/AES license

    http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd802930c5.html

    Rgds,

    AK

  • Option of range &amp; ASA 5510 - a group of objects

    Hello

    I have 3 ASA 5510 s; two of them are in production and the 3rd is new. I inherited two in production and was trying to set up this 3rd by using some of the existing network object-group statements.  The problem is that when I try to create a range of IP addresses in one of the groups of object; the range command is not available. One of the extracted statements from one of the ASAs production: network of the REMOTE object
    range 62.77.130.14 62.77.130.208

    The two ASAs have the same image of worm (asa842-k8).  Is there something I'm missing to enable the option in the range on the ASA News?

    Thanks in advance,

    ~ sK

    Hello

    Are you sure that the ASA News started the new 8.4 (2) software?

    There are

    • object-group network

      • accepts networks and addresses of host under it
    • network of the object
      • accept addresses from subnet, range and host under it

    Configuring "network object" came available in 8.3 software. Before that in the software 8.2 and earlier than the 'object-group network' (and other types of groups of objects") exist.

    Maybe you have several images start on the ASA News and its actually the old software still boot?

    What does the ' running shoe see the?

    If it lists both the command for old and new software then delete the old "system start" command, save the configuration and restart.

    I hope that the above information was useful

    -Jouni

  • How default context in plsu security edition asa 5510

    Hi could someon pls tell me with the edition of security plsu asa 5510 it will support active/active failover. and she supports context with securiyt plsu edition. and how default context do we receive with edition of plsu security asa 5510.

    concerning

    Assane

    Hello

    By default, ASA5510 with Security Plus comes with default 2 security [email protected] / * / firewall. Context of maximum security, you can have (upgrade to) is 5.

    With license upgrade of security Plus, you might have active/active and active / standby (choose one to run at any time) high availability services.

    http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd802930c5.html

    Rgds,

    AK

  • How to activate IP accounting or capture packets in Cisco ASA 5510 (8.2)

    Hi all

    Please help me for activation

    IP accounting packets or capture in Cisco ASA 5510 (8.2).

    Thank you

    Solene

    Hi Eric,.

    Create a list of access with the source destination ip address and/or tcp/udp ports

    can use it

    CAP_NAME access-list ACL_NAME buffer 12345bytes INT_NAME capture interface

    You can check capture

    See the capture?

    Name Capture PASSWORD

    |     Output modifiers

    Take care

    PaulC

  • ASA 5510 - tips for setting up - no internet

    Hi all

    I'll set up an ASA 5510 for the first time using the GUI.

    I put 0/0 0/1 and outside as inside.

    I set up outside with the static WAN address, and it is connected to my ISP.

    But I can't do everything Internet works on the inner harbor. I've read elsewhere, I need to add a static route. Can someone please advise?

    You must place a default route to carry traffic from inside to outside. Use the GUI to place a static route 0.0.0.0 0.0.0.0 for the ip address of your next hop ip of the connection to the ISP.

    Sent by Cisco Support technique Android app

  • Automatic update AIP-SSM-10 and ASA 5510 (Beginner)

    I see that it is possible to automate the updates of the ASA 5510 and AIP SSM via FTP on my own server. Is it possible to automate the download directly from Cisco.com?

    Thank you!

    Jeremy

    Jeremy, the answer to your question is correct, as far as the Cisco products are concerned. So I wrote a PERL app that does exactly that, and I published an article about it in the June 2007 issue of Sys Admin magazine. Here's the article online: http://www.samag.com/documents/s=10128/sam0706a/0706a.htm

    And it is also on my site, with a tar of scripts to:

    http://www.LHB-consulting.com/pages/apps/index.html

    Good luck.

    -Lisa

  • ASA 5510 BGP

    Hi all,

    I have a new BGP configuration that consists of two asa 5510 and two routers 2911 in the back. My question is: do asa 5510 support BGP?

    Thank you.

    Hi Sotiris,

    Unfortunately, the ASA does not support BGP (you can peer through the ASA but the ASA cannot be a peer BGP itself). The following link has a list of supported on the SAA routing protocols:

    http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/route_overview.html

    -Mike

  • ASA 5510 Configuration. How to set up 2 outside the interface.

    Hello

    I have Cisco ASA 5510 and the desktop, I want to create a new route to another (external) router to my ISP.

    The workstation I can Ping ASA E0/2 interface but I cannot ping the router ISP B inside and outside of the interface.

    I based my setup on the existing configuration. which so far is working

    interface Ethernet0/0
    Outside of the interface description
    nameif outside
    security-level 0
    IP 122.55.71.138 address 255.255.255.2
    !
    interface Ethernet0/1
    Inside the interface description
    nameif inside
    security-level 100
    IP 10.34.63.252 255.255.240.0
    !
    interface Ethernet0/2
    Outside of the interface description
    nameif outside
    security-level 0
    IP 121.97.64.178 255.255.255.240
    !

    Global 1 interface (outside)

    global (outside) 2 interface (I created this for E0/2)
    NAT (inside) 0 access-list sheep

    NAT (inside) 1 10.34.48.11 255.255.255.255 (work: router ISP inside and outside interface E0/0)

    NAT (inside) 2 10.34.48.32 255.255.255.255 (work: E0/2 router ISP on the inside interface only but cant outside ping).

    Route outside 0.0.0.0 0.0.0.0 122.55.71.139 1 (work)

    Route outside 10.34.48.32 255.255.255.255 121.97.64.179 1 (the new Road Test)

    Router ISP, that a job can ping and I can access the internet

    interface FastEthernet0/0
    Description Connection to ASA5510
    IP 122.55.71.139 255.255.255.248
    no ip redirection
    no ip proxy-arp
    IP nat inside
    automatic duplex
    automatic speed
    !
    the interface S0/0
    IP 111.54.29.122 255.255.255.252
    no ip redirection
    no ip proxy-arp
    NAT outside IP
    !
    IP nat inside source static 122.55.71.139 111.54.29.122
    IP http server
    IP classless
    IP route 0.0.0.0 0.0.0.0 Serial0/0

    FAI 2

    interface FastEthernet0/0 (SAA can ping this interface)
    Description Connection to ASA5510
    IP 121.97.64.179 255.255.255.248
    no ip redirection
    no ip proxy-arp
    IP nat inside
    automatic duplex
    automatic speed
    !
    interface E0/0 (ASA Can not ping this interface)
    IP 121.97.69.122 255.255.255.252
    no ip redirection
    no ip proxy-arp
    NAT outside IP
    !
    IP nat inside source static 121.97.64.179 121.97.69.122
    IP http server
    IP classless
    IP route 0.0.0.0 0.0.0.0 E0/0

    CABLES

    ASA to router ISP B (straight cable)

    Router ISP in the UDI (straight cable)

    Hope you could give some advice and the solution for this kind of problem please

    Hello

    Are you able to ping the router IP of the interface of the device of the ASA? If so, try a trace of package on the device of the SAA for traffic to the IP address of the router.

    Thank you and best regards,

    Maryse Amrodia

Maybe you are looking for

  • How can return my product ID of Windows 7

    My laptop is Windows 7 premium preinstalled. I lost the product ID for the resettlement. Can I get it back to HP a/s? Thank you very much and I will thank you more if that's possible! Serial number CNU0243XY0 Product number xc671pa Warranty status wa

  • Using the external keyboard with keyboard internal

    Hi people, Just got my new Tecra S4-122, of course without a built-in numeric keypad, so I have such a thing too. The problem now is that I'm not able to use the numbers on the keyboard without having to activate the internal "keyboard" (letters usin

  • signal names

    I use SE 2013 and I would like to know how to change the names of legend for thermocouples in the table in the data view. The signals currently posted under the names of the particular module channel.

  • External microphone realtek Y580 has a lot of comments/quiet

    I have the Y580 and the external microphone is extremely quiet. The works of micro fine on other computers and problems, is that the microphone is very quiet with many comments. If I use any help at all, I get too much feed back. I tried to use the R

  • Not found DVD Maker "DVD burner" message when DVD writer works well with other programs

    Hello I just created a DVD with AVS Video Converter and burned a DVD with no problems and created later a film with Windown Movie Maker, which worked well, it has exported to Windows DVD Maker, again not a problem, but when I click on burn, I get a n