Transformation of MSXML fails in Windows Server 2012 for adults

Similar Questions

• Fax to Pc ability does not work in Windows Server 2012 for Hp LaserJet MFP Series PCL6 1536

  I have install Hp Solution Center to use the 'Fax to Pc' feature in Windows Server 2012. But it is prevented Windows server 2012. How to use 'Fax to Pc' in Windows Server 2012?

  Sorry, but the Laserjet Printer has no CENTER of HP SOLUTIONS. The Toolbox, it is not the center of need. In addition, it is not compatible with the windows server 2012.

  The printer must be installed on a network in order to FAX to PC.

  1. you will need to type the IP ADDRESS in the address bar on internet. A page with your printer, and you will be set up there.

• Satellite C660 - 1 DG-drivers of Windows Server 2012

  I started Windows Server 2012 (for development purposes).

  Now... where can I find the drivers?

  * display driver *-lets start with the display driver (for the Intel Graphics Media Accelerator HD) when I look for the display driver in the support forum I only find the driver of Intel for Windows 7, but there is none yet for Windows 8? -Installed Windows 7 driver - works ok :)
  * sound driver * -.

  What drivers Miss do you?

  Fact is that Toshiba offers all drivers for supported operating systems.

• Graphic driver Intel HD in Windows Server 2012

  Hey guys, I downloaded Windows Server 2012 through Dreamspark yesterday and installed on my desktop. But the system cannot identify the Intel HD graphics 2000.When I try to install the official driver for Windows 8 to Intel. An error window came out and said that "the system does not reach the installation requirements.

  Could someone help on this problem, please? I expect Windows Server 2012 for a long time and this problem has made things stuck. I can't use my HD display at a very low resolution.

  Thank you.

  Uninsured, I don't know exactly what a thing make you laugh. No matter you believe it or not, it's here: http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=21180&lang=eng

  As I already said, what I find funny is the fact that some people like to say things like: "they have been waiting for Windows Server 2012 for a long time..." As it was the most important thing in the world, and as they wait for so long - it is a situation of fire for volunteers drill, they ask to.  It is the exaggeration of the issue that I find humorous.  Always, always will exist.  People think if they fall a few names, to mention a few things that make this situation 'important' for them - others will be more willing to help.  Often, this is the case - the human nature.

  Back to the part that mattered...

  "This software package will install the driver for the Intel® WHQL Intel HD Graphics 3000/2000 and® HD Graphics 4000/2500 for Windows 8 * Release Preview."

  Intel has drivers on Windows Server 2012 for other devices, but obviously not for the one you look at.  Just because they have one for Windows 8 does not mean it will work in 2012 Windows.

  Your problem is with Intel and what drivers they offer, not Microsoft (as I said already.)

  The drivers that you linked are for the Preview Release (foot) of Windows 8.

  If I were you, I would try all the drivers Windows Server 2008/2008 R2 for the product in question.  Although my quick research shows that none occurred for this chipset (probably because Windows Server is not a market that intel pushes for this chipset)-Yes, then I suggest to try the driver for Windows 7.  Using a Windows driver 8 beta is obviously NOT to give you the desired results.

  Try the Forums from Intel.

• Windows Server 2012 domain controller who fails to configure updates, coming back from changes.

  Hello

  I have a domain controller Windows Server 2012 which fails to configure updates. Each reboot it will say its configuration is updated, then in case of failure and Reverie. I can't find out what it is.

  I checked WindowsUpdate.log the only mistake I see there:

  2015 03-22 1000 1160 installation 09:36:29:735 caveat: SelfUpdate is in an error state

  Historical update check indicates a recent update that does not KB2770816:

  

  Download this update and install use autonomous to update manually the results of Setup in a message saying that the update is already installed (although windows search for the update in the updates installed appears without any results)

  I tried to launch the Windows update troubleshooting tool, that said he fixed a point, but after a reboot, I get always this error and now a new, every 20 seconds, I if I get this annoying modal popup saying that windows cannot check the updates even if it seems it can:

  

  Someone at - he counsel on how to locate the reason for the failure of the configuration of updates, perhaps, a log file will be useful information.

  Thank you.

  
  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• 12 c install on Windows Server 2012 fails on creating user

  Hello

  Tried to install 12 c EE on Windows Server 2012 using the interactive Setup program.

  On step 8 of 13 in the Setup is the screen specify user Oracle home.

  I selected 'Create a new Windows user' and entered oracle as user name.

  Things seem to be process fine until she apparently didn't try to create the oracle user.

  An excerpt from the journal of the installActions.

  INFO: instantiating 'D:\app\oracle\product\12.1.0\devdb\bin\chopt.ini'. INFO: instantiating 'D:\app\oracle\product\12.1.0\devdb\bin\chopt.ini'. INFO: Calling Action WindowsActionLib12.0.0.0.0  AddInstallUserToGroup parentGroupName = USERS OracleHomeBin = D:\app\oracle\product\12.1.0\devdb\bin nodeList = null INFO: Calling Action WindowsActionLib12.0.0.0.0  CreateUser userName = oracle password = *Protected value, not to be logged* OracleHomeBin = D:\app\oracle\product\12.1.0\devdb\bin INFO: Exception thrown from action: CreateUser Exception Name: WindowsSecurityException Exception String: Failed to Create oracle Oracle Home User. Exception Severity: 0 INFO: Exception thrown from action: CreateUser Exception Name: WindowsSecurityException Exception String: Failed to Create oracle Oracle Home User. Exception Severity: 0 INFO: Calling Action w32RegActions10.2.0.1.0  RegSetValue selectedNodes = null Key = HKEY_LOCAL_MACHINE SubKey = SOFTWARE\ORACLE\KEY_OraDB12Home1 value = ORACLE_HOME_TYPE data = 1 updateType = null INFO: updating registry key 'HKEY_LOCAL_MACHINE/SOFTWARE/ORACLE/KEY_OraDB12Home1' INFO: updating registry key 'HKEY_LOCAL_MACHINE/SOFTWARE/ORACLE/KEY_OraDB12Home1' INFO: Calling Action WindowsActionLib12.0.0.0.0  CreateOSGroup groupName = ORA_INSTALL OracleHomeBin = D:\app\oracle\product\12.1.0\devdb\bin nodeList = null
  

  Thanks for all the recommendations.

  Morgan

  Solved!  It is the value of password that I have provided the Oracle installer to create the new user of windows.

  The value was acceptable for the oracle Installer, but was not acceptable for Windows as a valid password.

  A better password and installation continued.

  Morgan

• Windows Server 2012 with EFI fails to start after reset of HA

  The purpose of this thread:
  1. a solution, if anyone else has this problem.
  2. If someone has a better knowledge of why this happens or how avoid feel free to explain it please.

  The scenario:

  I was a new analysis a HBA via the Web Client (something I've done many times before in the non-Web client without any problem...) and loses connectivity to the ESXi host. No response from the ESXi at all and I've noticed a GROUP... That's fine for now...

  The biggest problem is that the VM on the failed host installs via HA to my other ESXi in the cluster, each of them has started normally except my 2012 server s. Just the Automatic Startup Repair Wizard has started, and I couldn't do much from there... I tried a few things auto repair, but they could not fill...

  So, I entered the command line tools and ran from diskpart. Discs not presented at all. That's where he hit that I use PVSCSI drivers for my 2012 s server so I was trying to understand how I could inject the command line, but I tried something else first...
  I started the virtual machine on the ISO 2012 server. Tried the option repair, no OS not found to fix, so I chose a new installation and loaded drivers PVSCSI pvscsi-floppy, interrupted the installation and tried the repair option again. He said something like "Continue to start Windows Server 2012" and viola! The VM rebooted successfully and started successfully in the operating system.

  All 3 2012 Server virtual machines on failure that esxi is affected. No Server 2008 or linux where affected machines but they do not use the pilot PVSCSI.

  
  Anyone has a solution alter or maybe an explanation why this happened? This will happen if HA into action on my server 2012 s?

  Is it possible to test or confirm without killing an ESXi host?

  I am running vSphere 5.5 and I don't think that I had this problem with 5.0 or 5.1, but I'm not 100% sure that cause I don't remember no matter which GROUP or another that are running older versions of the failure.

  Hardware version is 9, EFI boot.

  Thank you!

  Finally, I solved this... Looks like a mistake to the EFI initialization after reset of a HA. I know EFI is not supported by FT but I'm only using HA I can't find anywhere that it says that it should not work.

  This is how I fixed the corrupt WS2012 boots:

  1 boot WS2012 ISO, select new installation, load drivers PVSCSI, interrupt installation and choose repair. (Only needed if PVSCI-pilot helps you bootdisk)
  2. choose Help and then command Promt
  3. Run diskpart
  flight type list
  Locate the number of the partition-small FAT32 EFI, in my case nr 3
  Salt type flight 3

  type assign

  flight type list

  Choose the letter assigned, in my case E:
  Type exit

  4 cd /d e:\efi\microsoft\boot

  5 ren BCD BCD.bak

  6 bcdboot c:\windows/l en-us/s E: /f ALL

  7 bootrec /fixmbr

  Bootrec /fixboot

  Bootrec /scanos

  Bootrec /rebuildbcd

  Don't know if all these are necessary... However, it works. Note that the scanos and rebuildbcd show 0 found BONES.

  8 exit the command prompt and click on "Continue starting the server 2012" after that recharge should work properly again.

• Can not remove the print server role (Windows server 2012)

  I have a small question... I'm trying to remove a role (print server) on my Windows Server 2012. (Yes I know, I need to go to "Add/Remove role")

  

  but each time, the server establishes the uninstall procedure, but when it's time to restart and complete the procedure... the server fail and cancel everything... so in the end I always install the print server.

  

  I try to stop a link of service in this role (as a spooler, printing...) but samething.

  If anyone can help me, I really appreciate it.

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Prerequisites for domain controller promotion is not for windows server 2012

  For windows server 2012 check of preconditions for the promotion of domain controller has failed. TCP ports required by Active Directory Domain Services are already in use on this computer. You must remove or reconfigure the services that currently use these ports (88, 389, 636, 3268, 3269).

  Support is located in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Updates Windows Server 2012 faulty - stuck at 67%

  For the past 3 months my server 2012 no R2 VM was the fault of updates. If this is an update to Windows Server 2012, it fails. It is not related to an update of the server 2012 specific windows, but they all fail. I can run updates updates/Silverlight IE without any problem.  After that I installed them and restart it gets stuck on configures updates 67% then eventually restarts and returns and sometimes it does not many times. This is getting extremely frustrating.   -Thanks for any help

  Please post your query to:

  https://social.technet.Microsoft.com/forums/

  Server issues are better addressed there.

• Windows Server 2012 Foundation - installation of recovery DVDs - Activation question

  Hi all

  Please could you help me with the following text:

  After the installation of Windows Server 2012 Foundation of Fujitsu Operating System Recovery DVD Fujitsu server activation does not work. Error code: 0xC004E003, Error Description: The Software Licensing Service reported that license evaluation failed.

  Thank you

  Ivo

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Windows Server 2012 lost connectivity

  Hi all

  I created 6 virtual servers Windows Server 2012 R2 Standard. However, there are 2 weeks 3 to 6 servers randomly lost connectivity (ping returned request) outdated, unable to control remotely,... several times until I have restart servers, connectivity was back. Even if 3 other servers do not have this problem.

  I found the following error events in the event viewer, I don't know if they cause this problem or not:

  Log name: System
  Source: Schannel
  Event ID: 36888
  A fatal alert is generated and sent to the remote endpoint. This can lead to the termination of the connection. The defined protocol TLS fatal error code is 40. The Windows SChannel error state is 252.

  Reference: https://msdn.microsoft.com/en-us/library/windows/desktop/ms678421(v=vs.85).aspx

  -------------

  Log name: System

  Source: NETLOGON

  Event ID: 5719

  This computer was not able to set up a session securely with a domain controller in the domain GHPFE because of the following:

  Currently, there are no available connection server to process the logon request.

  This can lead to authentication issues. Make sure that this computer is connected to the network. If the problem persists, contact your domain administrator.

  MORE INFO

  If this computer is a domain controller for the specified domain, it puts up the session for the specified domain PDC emulator. Otherwise, this computer sets up the session secure at any domain controller for the specified domain.

  Reference: https://support.microsoft.com/en-us/kb/938449

  Microsoft warning serious problems can occur if you modify the registry incorrectly by using the registry editor or by using another method. These problems may require that you reinstall the operating system. Microsoft cannot guarantee that these problems can be solved. Modify the registry at your own risk.

  -------------

  Log name: Application

  Source: CAPI2

  Event ID: 4107

  Has not taken from the root list third-party auto update cab at: http://ctldl.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab> with error: these data are incorrect.

  Reference: https://support.microsoft.com/en-us/kb/2328240

  -------------

  Log name: System

  Source: Client DNS events

  Event ID: 8015

  The system cannot save the host (A or AAAA) resource records (RR) for the network adapter

  Reference: http://support.simpledns.com/kb/a182/system-failed-to-register-host-resource-records-rrs-network-adapter___-warning-windows-event-log.aspx

  -------------

  Log name: System

  Source: Group policy

  Event ID: 1054

  The processing of Group Policy failed. Windows could not obtain the name of a domain controller. This could be caused by a name resolution failure. Check your service provider Internet (DNS, Domain Name System) is configured and working properly.

  Reference: https://support.microsoft.com/en-us/kb/324174

  Microsoft Cause: This problem may occur if the address of a preferred DNS server configured on the client is invalid or is inaccessible.

  -------------

  Is there anyone know of this problem and the resolution to it? Help, please.

  Thank you

  Khiet Manh

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• How to install Visual Studio 6.0 on Windows Server 2012

  I have a build server that is located on Windows Server 2012.  I need to install Visual Studio 6.0 to build some of our VB and C++ components.  Whenever I run the Setup fails.  Can someone please tell me know how to install VS 6.0 on Windows Server 2012?

  Hello

  Please post your question in Server TechNet Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Error activation product key has been used already on Windows Server 2012.

  Original title: Activation error

  Two days ago, I installed windows server 2012 on my PC... It has been corrupted because of virus on my USB key that I reinstalled it twice but both times, it has been corrupted... when I installed it third time Activation has failed, it is said that this product code was used on another pc... no activation now please help me... and one thing I've never done any material change

  Try the phone activation, you may have to do during the week:

  1. press the Windows key + X , and then click run, and then type: slui.exe 4

  2. then press the ENTER"" key.

  3. Select your "country" in the list.

  4. choose the option "activate phone".

  5. stay on the phone (do not select/press all options) and wait for a person to help you with the activation.

  6. explain your problem clearly to the support person.

• 6 of WSUS on Windows server 2012

  Hello

  I am trying to configure SCCM 2012 (painfully)
  I get a lot of error messages.
  WSUS does not work: can not synchronize updates.
  wsusservice (in services.msc) will not start (error 193 oxc1)
  If wsus works 50% (you can see some Update Manager wsus on windows server 2012) because some service: do not start WSUSservice and ContentSyncAgent!
  In sccm 2012 config console manager, status of the status/component system, I get a critical error for SMS_WSUS_Control-Manager:
  Failures have been reported on the "our FULL domain name server" WSUS server for WSUS 'ContentSyncAgent, WSUSService' components,.

  Solution: Check that the failing WSUS components are installed and running.
  another mistake criticism for SMS_AMT_operation_Manager:
  The service point of band off unable to connect at the point of registration.
  Our config:
  WindowsServer 2012, sql server 2012, sccm 2012 sp1 on hp proliant Server
  It really painful
  Thank you if you have an idea

  Hello tomy13,

  Microsoft Community is for consumer issues on Windows 8, Windows 7, Windows Vista and Windows XP. As your question is about 6 of WSUS on Windows server 2012, your question would be better addressed in the TechNet for ITPros forums.
  Click on the link here to transfer your question in TechNet in the Windows Server forum.

  Sincerely.

  Marilyn