tried to reinstall the operating system and it crashed

Acer One Netbook D257.

Installed to 2 g of RAM (you have to take all this goes to do!) and since then the wireless is uneven right next to the router unless.

So, I thought it would be a pilot. Tried to install the driver from Intel. That didn't fix it.

So I thought I would start fresh by reinstalling the operating system using the Acer tool that backs up the user's data.

Wonder of wonders, it doesn't at all now! System 7 House is caput! He starts up a message saying that Acer could not install the OS!

Suggestions? How can I get a copy of "acer" of win7 to replace on this netbook?

TIA

Ron

Alrighty then, here is the resolution!

Apparently, there is a removable rear on this computer! You must know the 'secret' to open the door!

The 'trick' is to remove the keyboard, and then there are 5 magic screws that release the rear panel.

There are two right under the disk hard corners L & R and then there are three online in the upper part of the hard drive. One of those is to the left of the upper-left corner (probably as he field key 'E'?) Once you do this, dislodging then the back is yet another task. Fortunately for me, I pushed inside to understand. There's "brand" in the plastic that indicate you the five. Just look at the two bottom and you'll see what I mean.

The other thing to know is that the back side of the Panel has hooks that need to go first when back, which means that it is NOT the starting point of prying eyes. The other 3 sides are 'snap' as push so I think that starting with a front corner notches to stop might be the best solution, otherwise you will destroy the hooks.

The problem with dropping the network was the antenna wires that connect to the transmitter. They were loose. They do not have much of a loop service for them so when I raised the mobo to install memory, the first time, they jumped off. The antenna is located around the monitor bezel.

Now, it works fine.

Why they have not make obvious to repair this unit is a mystery. I guess for $250, it's a deal, but then you get watered to have someone for you install memory.

If all goes well, I saved someone some $ and headaches this announcement.

Enjoy

Ron

Tags: Acer

Similar Questions

  • I reinstall the operating system and I have to delete all programs, including photoshop and lightroom. I put it again and offered to buy them, even if I already pay for them

    I reinstall the operating system and I have to delete all programs, including photoshop and lightroom. I put it again and offered to buy them, even if I already pay for them

    In addition to the steps mentioned above, you can also try:

    First of all, disconnect, then back into creative cloud, using adobe id to pay for your subscription.

    https://helpx.Adobe.com/creative-cloud/help/sign-in-out-activate-apps.html

    Then, if you launch any product of CC 2015 and the pop up still shows a trial message window, please check this link for the resolution:

    https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html

  • I have Adobe Acrobat 9 Standard on both of my computers.  Some time previously, one crashed my computer and I had to reinstall the operating system and all applications.  After you install Acrobat 9 special and differential treatment in the computer once,

    I have Adobe Acrobat 9 Standard on both of my computers.

    Some time previously, one crashed my computer and I had to reinstall the operating system and all applications.

    After you install Acrobat 9 special and differential treatment in the computer once, I wanted to update the update of the version 9.0.0 software to the same level as it was before the crash and that the other computer has version named 9.5.5.

    The update to version 9.0.0 system does not at all. 'There is no update' listed in the dialog box.

    Can you advise how to get my Adobo Acrobat 9 Standard (Version 9.0.0) could be updated to the same level it had before the accident.

    FTP://FTP.Adobe.com/pub/Adobe/Acrobat/Win/9.x/

  • Pavilion HPE H8 - 1360t: need to reinstall the operating system and software preinstalled on new hard drive on HP Pavilion HPE H8 - 1360 t

    My hard drive crashed while I have to reinstall my operating system and the software pre-installed on a new hard drive. I have no recovery disks. What should I do?

    Marcel, welcome to the forum.

    Here's a guide to help order you HP system recovery discs if they are still available.  If this isn't the case, you will need to purchase a full copy of the operating system.

    Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

  • Portege 3440CT reinstalling the operating system and error NTLDR

    Hi all

    I have a Portege 3400 I picked up a few years ago when starting a business. The machine was made by many, and it no longer starts. I want to reinstall the OS - the only problem is that I don't have the original CD Rom drive that came with the unit. I have a portable CD player that I can plug into the USB port of the adapter, but during the taking of a boot device, it is not yet trying to look for the CD player and immediately gives me an NTLDR error.

    The only option for the boot device which does not give me the same error is when I take the network (Lan), but I have no idea how to do to set up my local network so I can use it as a source for the reinstallation of the operating system.

    Can someone help me?

    Thank you

    Manish
    Matt (at) Gen - a (dot) com

    Hello

    The error NTLDR says that your device or disk is not bootable. What OS did you use? I know that Windows NT doesn't support USB.
    Please check out this article written by Microsoft:
    http://support.Microsoft.com/default.aspx?scid=kb;en-us;196661

    Also, I found a topic in the forum with a similar problem.
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=2182&MessageID=6043#6043

    Good bye

  • How to: format and reinstall the operating system

    Original title: is there a virus that downloads all the images that appear on windows xp family within 24 hours, I have acquired 17 000 images and used to my PC I want to enter windows in any mode

    I can't navigate what whether in safe mode with or without networking. How to flatten the system, which dates back to the original state that I'm not bothered about registering files images etc want just my PC to work

    Hi wendyspeariett,

    1. you receive an error message when you start in safe mode or normal mode?

    2. did you of recent changes on the computer?

    If you have access to the internet in safe mode with network, then you will need to scan the computer to remove all infections from the computer and check if that helps.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx 

    You can also use Microsoft Security databases to scan your computer

    http://Windows.Microsoft.com/en-us/Windows/products/security-essentials

    If you want to format new Windows XP installation, you can move forward.

    A new installation is to remove all data from your hard drive repartition and reformat the hard drive and reinstall the operating system and programs empty (clean) hard disk.

    How to install or upgrade to Windows XP

    http://support.Microsoft.com/kb/978307

    How to partition and format a drive hard using the Windows XP Setup program

    http://support.Microsoft.com/kb/313348

  • Impossible to download and reinstall the operating system after erasing HD

    Yesterday morning, my iMac won't start.  It was fine the night before.

    The progress bar reaches about two thirds to three quarters of the way to the end when the bar of progress disappears and I find myself with a gray screen. It does this by starting too.

    I followed the advice of Linc Davis at https://discussions.apple.com/message/21333265 (hash) 21333265 (Note - I can't find the symbol of hash on my keyboard key so if you if know where he is, please replace by in the link - oh (hash) and tell me where it's too please ;-)).

    I started the Revovery volume (now here actually).  Run Disk Utility/First aid finds no problem with MacIntosh HD (my boot drive). I can't find how to repair permissions.  The option no longer seems to be there. Reset NVRAM has nothing else that makes the iMac wonder my preferred language.

    I used download and reinstall OS option.  The first time I tried to re-download El Capitan, it took 15 minutes and 45 minutes to install.  Installation failed leaving me to the grey screen again.  I think that the Setup program itself was trying to restart the iMac when he got stuck in the same place I'm stuck.  I left it there for about six hours before I tried to restart manually.

    Tried to download the operating system again. This time, it was after using the recovery volume, select MacIntosh HD, by using erasing, then the option reinstall in THE.

    I did two times now.  The first time I tried 'Erase and re - install' the download bar has got to a point about a third of the way across, and then he stopped. Time of download bar gradually got more and more long, up to what I canceled it (when the display estimated download time is six and a half).  The internet connection was problematic, or the Mac had stopped download (similar to the earier progress bar).  The second attempt to delete and download, the download bar has not yet started to progress.

    My HARD drive has several volumes.

    1. The most important. My MacIntosh HD with OS 10.11.4 - El Capitan.
    2. The second, MacIntosh HD 2, is about 50 GB, a Mavericks installed on it.
    3. The third is 10.11.4 recovery volume.
    4. The fourth is another volume of recovery for the Mavericks.
    5. There is another called eDrive bulkhead.

    Apart from MacIntosh HD, with none of these volumes I problems in starting up (with the possible exception of the Mavericks resumed, that I have not tried to access all since the update to El Capitan).

    I used first aid utility disk several times, and no problems have been reported. I used the version of El Capitan permanently.

    I can't understand why, after erasing the MacIntosh HD to do it again, I can't get the iMac to download the MacOS and reinstall.

    A couple of clues-

    • After his clear utility drive always reports what is MacIntosh HD. (When I restart, the dialog "Select Start Drive" only shows the volume of the Mavericks and eDrive)
    • Disk utility also shows "Apple Disk Image/OS X Base System."  OF THE said that it is ejection. But this button does not work.  I suspect it's what might stop download me the installer and start again.

    I used e-drive to check the iMac and, in particular, the drive HARD; even performed a surface scan.  No problems have been reported.

    Your 2007 iMac is too old to download OS X, you need to install OS X since the recovery partition directly. If this does not work then Yes, something is wrong with your HD run Apple Hardware Test Mode Extended 2 - 3 times back to back, if errors appear which confirms what I said. You will need the original DVD that came with the computer in order to run it.

  • Can I get an installation Win XP Pro Update CD includes SP3? The one I have now is pre - SP2 and reinstalling the operating system takes 4-EVER!

    My existing Windows XP Pro installation CD is almost a decade, and it precedes SP2. It's a nightmare, whenever I have to reinstall the operating system as ut takes a day or two to download Microsoft updates. Is it possible to replace my installation CD with a newer version, including a number of post-SP3 updates and SP3?

    You do this using a technique called "slipstreaming".  You start with a genuine XP installation CD and add in the necessary service packs and updates.

    If your CD-ROM is sp1 or 1A, you can just slipstream sp3.  If you have XP 'or' (pre - sp1), it is more complicated.

    There are many websites that explain how to do this.  Google for "slipstream sp3 of xp" or something similar.

    This site claims to have a script that will create a slipstreamed XP sp3 and all post-sp3 CD critical updates (description wrongly "sp2").  I the have not used and do not have any information on how easy it is or if she actually does what it says.

    See also http://social.technet.microsoft.com/Forums/en-US/itproxpsp/thread/eff07503-cf09-4ada-b327-410d341450b9/

  • "Don't use this CD to reinstall the operating system on Dell count" that I had in 2004 and have more... what I want to know I can install it on a different computer now and it would be legal?

    Original title: Original Windows XP cd.

    I have an original cd of Windows XP Home Edition with the product key for it and want to use it... but when I look at the disk, according to me, he said: "Don't use this CD to reinstall the operating system on Dell count" that I had in 2004 and have more... what I want to know I can install it on a different computer now and it would be legal?

    Because Dell SLP, the restriction of similar model is not important. All that matters is the EULA and the fact that the two computers are Dells.

  • Good afternoon__I have lost my installation CD. I have a correct key at the back of my PC. How can I get an another installation CD? ___I trying to reinstall my operating system. The PC is already formatted. ___Thank you in advance. __ANPW__

    Good afternoon

    I lost my installation CD. I have a correct key at the back of my PC. How can I get an another installation CD?

    I'm trying to reinstall my operating system.  The PC is already formatted.

    Thank you in advance.

    ANPW

    How to replace Microsoft software

    Carey Frisch

  • I crushed my desktop under Vista SP2 and the repair shop transformed old files by (.old) and reinstalled the operating system.

    I crushed my desktop under Vista SP2 really bad and couldn't get it to work again. I took it to the repair guy and they converted all the files (.old) and then reinstalled the operating system that has recovered the old files and got the computer running again. All the old files use about half of the hard drive and I want that space back. Is it safe to uninstall the old files? Thanks for any help and suggestions.

    Hello

    as long you have recovered your data it's ok to delete the windows.old folder

    How to restore your personal files after you perform a custom Windows Vista or Windows 7 installation

    http://support.Microsoft.com/kb/932912

    It's the same way for Windows vista to remove

    How can I remove the Windows.old folder?

    http://Windows.Microsoft.com/en-us/Windows7/how-do-I-remove-the-Windows-old-folder

  • I just had to wipe everything on my mac and reinstall the operating system.  How can I get my products Adobe Creative Suite back on my computer?

    I just had to wipe everything on my mac and reinstall the operating system.  How can I get my products Adobe Creative Suite back on my computer?  I do not have a disk.  I think I bought the package online.  I don't see anywhere to re - download.  The purchase was made in 2011.

    Any help?

    Available downloadable Setup files:

    Download and installation help links Adobe

    Download and installation to Prodesigntools help links are located on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions". window using the Lightroom 3 link to see these "important Instructions".

  • How can I reinstall the operating system with the recurring kernel panics?

    MacBook 1.1, white, plastic, 2.0/2x1GB/80GB/SD/USB.

    It used a lot, but want to keep going for special purposes.  Get kernel panic/black screen when I try to reinstall the operating system on a blank disc;  deleted before trying to reinstall Lion 10.7.3.  Tried other earlier versions of operating system.  Reinstall the memory chips and ordered new ones as a bet.  Made a "Lion" partition the Middle clone backup FW for my MacBook Pro, but there now El Capitan; window said I have bad installer in MB Pro; Cannot install on this new FW partition, but I don't know if this will help anyway.  Must be HW problem; nothing on the MacBook drive.   Diagnosis I could not complete either.  Impossible to wipe FW with the MB Pro, Lion and other stuff loading to attack the problem of HW?   Don't know how to do in this regard.  A new Disk Warrior 5 and old Tech Tool Pro.  Apple HW Test on the original disc from MacBook will not appear either?   Difficult OB!    Challenge yourself, please!   New mem circuits can do. ??

    So I'll try to attack it from the external hard drive, of course, I have to.   But how to find and eliminate the block HW?   Finally, go ask Apple support.

    It doesn't let me finish any operation!

    According to Mactracker, a Macbook 1.1 is limited to Snow Leopard 10.6, as the new OSX compatible.  Do you mean you had lion (10.7) installed?

    Ciao.

  • Satellite L850D - 12 p: need to copy of Windows 8 to reinstall the operating system

    Hello

    I have a Satellite L850D - 12 p and need a copy of windows 8 to reinstall the operating system

    I deleted all the data on the HD including the recovery partition, I don't envy spening £30 order disks and want to download the

    The supreme macine provided with Windows 8...

    Thank you

    Jaz

    It of not possible to download a recovery image Windows 8!

    If you have not created the disc clean recovery or recovery USB flash stick memory such as mentioned in the user manual, you must order such environment.

  • After the last update of the operating system and iMovie it seems I can't create a movie in the PAL standard. Can anyone help?

    After the last update of the operating system and iMovie it seems I can't create a movie in the PAL standard. Can anyone help?

    NTSC and PAL are analog standards and don't apply to the share or export settings in iMovie.

    It creates the same FPS and dimensions as your source file.

    What you trying to create?

Maybe you are looking for

  • Clear history does not

    Usually I ctrl + shift + delete to clear my history/cookies/etc, or on the rare occasion I'll click in the drop-down box. When I tried to erase my histroy today, the box with the options to clear the history didn't pop up.

  • HP 120-011 to: attach a new Nvidia Geforce GT 710 graphics card to HP 120-011 in

    Hi, I want to install a new graphics card on my desktop pc HP 120-011 in . My office is currently integrated Intel HD graphics 4400 . I recently bought a Nvidia Geforce GT 710 graphics card, but when I inserted in a PCI-E port, the pc is not able to

  • Can not play the movie bluray with Corel WinDVD on my Satellite A665-11Z

    Hello When I play a movie with Corel WinDVD bluray, it plays over/under 10 seconds. "Then I get the message" your display environment does not support protected content.I played a Blu - Ray player on my laptop before and it worked perfectly. Is there

  • HP2210 printer: Hp2210 printer all in one

    I cannot connect my printer to the desktop computer. What I see, he has a place for two phone lines but not usb plug. Looks like that one is to log on to the computer and the phone. Buy the way I have the computer hooked to a wireless net work law do

  • How to solve the problems highlighted in each journal in the issues of the CBS

    Hello Please could someone help me decipher the CBS logs for two of my Vista machines and tell me how to solve the problems highlighted in each journal. Vista 1 machine has Vista Ultimate x 64 SP2 installed and has been implemented in the following w