trigger time N

I use a 6363. I want to trigger a pulse to synchronize incoming exactly N times. These impulses are coming in the ~ tens of kHz range.

My first idea was to make a task of CO County ticks on the same impulses and plug a relaxing break, but pause triggers apply only to the continuous acquisition.

My next idea was to hang the task of CO County ticks as the arm trigger defined on 'Good to go if it is high' and not 'arm on front amount', but it seems that it is not in the cards more.

Another idea was to use the impulses of synchronization entering as a sample of clock on a binary ripple of 10101010101 (N repetitions) and use the trigger set instead. But it seems that the binary signals cannot be deployed to advance until its next value on a rising or a falling edge, therefore leading to another each pulse.

Do I need to use a transistor outside Commission to do (with County CO ticks)? Who would do it, certainly, but it seems kludgy.

.... Are there clever ways to do? If not, is there a way to get the binary waveform to advance on the edges of increase or decrease?

It has a hardware signal as well (that confusingly enough is called the "change detection event").  "You can use it by setting your clock source' //ChangeDetectionEvent '.  It will not be displayed in the drop down menu to DAQmx default termnals because it is considered 'Advanced' (see here).

Best regards

Tags: NI Hardware

Similar Questions

  • cannot trigger time DAQ and camera

    Hello

    I want to synchronize a camera and a pressure transducer. The pressure transducer is connected to an NI USB-6251 housing.

    I use a TTL signal to trigger (trigger signal is from a Labjack). If I only connect the camera, I can trigger without problem. If I only connect the DAQ card, I can trigger without problem. If I use a T-connector for both trigger the camera and the DAQ, only the DAQ card card is triggered.

    An idea of the source of the problem and how can I solve this problem? Thank you!

    Charlotte

    OK, so I checked my TTL signal, and it was disrupted once cut in two. I pulled out another TTL signal such as the camera and the DAQ card each has its own TTL trigger: it works well and now I can enjoy my weekend )

    Thank you

  • trigger expire in 2012 VBAI

    Goodmorning,

    I VBAI have experienced lately, and I have a slight problem. When you use a hardware trigger I sometimes have a downtime.

    My trigger is a 24V signal and my cam is a G201C of Manta (ally). (Look at this message below for the trigger parameters).

    In NIMAX I can configure the time-out, but in my opinion, this is the maximum time between the trigger and the arrival of all the packets of data (acquisition of delay). I thought that in previous versions of the VBAI, we could also define a relaxing stop time (in the tab trigger). Problem is, however, that in VBAI2012 there is no longer a tab trigger. And in the attributes tab, I can't find the trigger time out.

    Any ideas where I can put this trigger expire?

    BTW: With trigger time off I mean the timeout if the there is not a trigger signal after some time. Here's where this used to be (http://www.ni.com/white-paper/6158/en)

    Here is my triggersettings.

    -TriggerSelector: AcquisitionStart

    -TriggerMode: on

    -TriggerSource: line1

    -TriggerActivation: RisingEdge

    -AcquisitionMode: multitrame

    -AcquisitionFrameCount: 1

    Any help would be greatly appreciated. Thank you

    Tom Declercq

    OK, now I see the problem. The time-out is not an attribute of camera, it is an attribute of the pilot. If you click on the "Show all attributes" box and scroll up, there will be a section called the Acquisition attributes and provided for in this article. Sorry for the confusion and hope that helps. I hope to make a similar tab type of the trigger in the future for this step to make it easier to find all those attributes in the same place involved as we had during the stage of 1394 former.

    Thank you

    Brad

  • Display in real time with a delayed recording LV6.1

    Hi, I need help with LabView 6.1

    I have a hardware module FieldPoint where I read 8 channels for thermocouple. I want to display the value of the thermocouples in real time (or as close as I can manage) all saving the values in a CSV file at discrete time intervals (every 10 seconds). I am able to display the values in real-time, but the recorder real-time records, produce a lot too much data. I'm able to delay the recording interval, but in bulk then display in real time!

    The following example shows a method I've tried. The delay time in the loop of logging seems to delay the entire program. I also tried to use the loop of the logging of a sequence (using a simple delay of 'Wait') structure and a structure of matter (with a counter and only do the loop of logging real when the counter gets to 1). I tried to configure synchronous display without success.

    I'm having no luck and wonder if someone could point me in the right direction?

    Ah, the benefits of time.

    I think that I managed to create a solution for me using a different tact. Instead of using individual meters of delay, I used a "trigger time" approach as demonstrated in this thread;

    http://forums.NI.com/NI/board/message?board.ID=170&message.ID=286988&query.ID=6280650#M286988

    Currently, it is limited because it will allow only a delay of 59 seconds between the readings, but this should be relatively easy to solve. The solution works continuously update the display with a slight delay to help cope aging computers, and then the button "Log Data" is selected writing worksheet function is called second pushed together as selected. Quite a simple and elegant solution I think.

  • display time in form 6i

    Hi all

    work on form 6i

    I want to display a time on my canvas. It must display the time...

    How can I?

    Please help me...

    Thank you

    You can create a timer on a TIME-NEW-FORM-INSTANCE with an interval of 1 second and on WHEN-TIMER-EXPIRED you can set the time to a piece of text on your Web Forms.

    WHEN-NEW-FORM-INSTANCE
    
    DECLARE
     timer_id Timer;
     one_sec NUMBER(5) := 1000;
    BEGIN
      timer_id := CREATE_TIMER('emp_timer', one_sec, REPEAT);
    END;
    

    And then the trigger TIME-CLOCK-arrival at EXPIRATION, you can do it like this:

      :YourBlock.YourItem := to_char(sysdate, 'HH24:MI:SS');
      SYNCHRONIZE;
    

    I hope that helps!

  • (BUG) Problem creating events of the calendar in the past (IOS 9.3.1)

    Recently, I get such a problem:

    1. I opened a last date in the calendar default ios

    2. create an event:

    -put the name of the event 'Accident '.

    -day 17 April 2016

    -start time 16:00 (end time 17:00)

    -all other attributes - default:

    calendar by default (have also 1 calendar personalized in a list)

    No rehearsal, no trigger time, no participating, call back in 30 minutes

    * a tried also the attributes of different event with the same effect. Didn't help not also choose my google calendar. tried several times)

    3. Press 'Add '.

    wait: event created, appears on that date and remains

    get: event appears and disappears in about 1 second

    What could be? Can help you with this? What IOS Bug?

    Creation of future events - no problem

    Settings - Mail, Contacts - synchronization scroll to calendars - events - How back does go - you may need to reset it to take account of the date that you set the old event from

  • distributed antenna system usrp 2920

    Hi all

    I implemented an OFDM transceiver using two usrps one transmitter and one receiver, I also did all the normal tasks of synchronization (detection of frame timing recovery, CFO correction and channel estimation) needed to compute the BER to the receiver and it worked very well.

    IM now trying to imitate a DAS scenario where I have two transmitters USRP sending the same exact OFDM signal, they are separated by a distance and synchronized in frequency and time using a reference clock. The receiver is a normal OFDM receiver. Thus, the received signal from two transmitters must be seen on the receiver side as the same signal from a transmitter, but with a higher power. Moreover, I need to induce delays of a nano-second between issuers using the trigger of startup time and study the effect on the BER is it possible?

    My questions are:

    1. it a phase ambiguity between the two transmitters usrp after the use of the reference clock or cable MIMO?

    2 - is possible to use the Refin and the PPS and the different trigger time to force specific transmission times?

    Thank you

    Hey Kareem,

    Yes, this should be possible. As long as you use the same reference clock for your USRPs there should be virtually no delay phase. The only delay introduced would be due to the length of wire between USRPs.

    Looks like you have two different triggers and they are independently controlled. As long as you do not start the transmission until the USRP receives a trigger, you can specify a delay between transmission by simply delaying one of the triggers of your desired time.

  • Values aus copying Kanal wenn Triggerkanal von 0 auf 1 out und anschliessender xls export a certain Stellen der Datei

    Hello

    Am erst seit kurzem mit Diadem kenne mich und mit der Skriptfunktion noch nicht gut aus really.

    ICH habe ein Triggersignal fur 5 Sekunden meistens which attached und in der Zeit von 1 auf 0 umspringt.

    Die ich m values von it Kanalen immer zu dem wenn der aktiv ist Trigger time. However thankyou ich den Mittelwert bzw den Wert 3 Sekunden vor Ende of the triggers (den ich nehme Wert als Mittelwert one).

    DIAdem soll also das Triggersignal absuchen und as soon as der Sprung von 0 auf 1 kommt soll are 3 Zeilen und mir den Wert von it Kanalen enter go back. welche channels das exactly sind weiss ich noch nicht, das wird aber feststehen wenn ich das Skrip starte und die werden sich auch nicht change channels.

    Pro measurement will der Sprung ca 30-40 hurt statt. Die Anzahl der Sprunge unterscheidet sich von zu measurement measurement.

    Kopierten values soll die are a new channel schreiben. Line 1 sollen dann Die values first Trigger, line 2 die values vom vom 2. Trigger Steelworkers.

    Die neuen channels sollen am Ende der Gruppe werden aus der die its values come added.

    ICH will also am Schluss several neue channels haben die Zeilen haben wie Triggersignale Ich habe viele so.

    Ist possible sowas? Und wie realisiere ich das?

    Mit der Aufnahmefunktion kam da nur das raus

    Call the DataBlClpCopy ("' [2] / T_BT ',' [2] / DI_2'", 104, 1 ') '... ChnNoStr, ChnRow, ValNo

    DI_2 ist das Triggersignal und T_BT einer der zu kopierenden channels aber da fehlt stop der zu DI_2 und ich nur einfach die line 104 kopiere perspectives.

    Danach sollen dann sharp values die ich hab in eine Datei werden used excel rausgeschrieben. DAS grosse problem dear ist, dass ich einen header hinzufügen muss eine excel-datei lade certain Zeilen und sich bzw mit den Messwerten replace muss. In den Zeilen steht und values text. Die muss ich replace values.

    Fur jeden Trigger soll eine Datei erzeugt werden. Also nacheinander am ich die Zeilen von meinen before erzeugten Triggerdaten ab.

    Sowas überhaupt ist mit Diadem possible oder ist're besser wenn ich dazu really Matlab?

    Ware super wenn ihr mir helfen könnt.

    Gruss Normann

    Hello Norman,

    Klar kann man das in DIAdem machen. ICH habe ein example standing refer. Eine Alternative zum Export von Daten aus nach ist der nach import Excel TDM-Dateien von Excel DIAdem. Refer there're das TDM-Excel-component snap, dass of the last http://zone.ni.com/devzone/cda/tut/p/id/4906 Commission kannst.

    DAS example will die Triggerstartpunkte, und die values 3 before in channels ein neue Zeilen aus want. Wenn alle Daten sind zusammengestellt, werden die Daten an Excel organizers. Testen kannst der angehangten Daten und starten Scripts loaded durch das.

    Gruss

    Walter

  • 2651 a conversion of TSP Script for LabVIEW

    Hello

    I have a problem on the conversion of all TSP scripts that contain functions and appeal for the end loops. I'm new to the TSP with models of trigger scripts. I used the Script Builder (TSB) Test tool and am able to run any TSP and generate raw data, but I don't seem able to convert most of the codes in the command of LabVIEW VISA or loader LV TSP TSP and run it to generate data... I can't find any tutorial or examples how to do it.

    Let's say that... Use the example of KE2651A_Fast_ADC_Usage.tsp (pulse) and I'll just focus on the portion of function CapturePulseV (pulseWidth, pulseLimit, pulseLevel, numPulses). I have seen a few examples of LV that says loadscript myscript and close on endscript.  I did a lot of different approaches, and I kept getting errors in particular the print function that I am not able to generate data through LV by to read the data in the buffer to inside the instrument. Some approaches, I have had no errors but no data... Some approaches, I got error-285.

    The part of the code TSP pulse that works in TSB is here (I'm not including loadscript and endscript) and what is the RIGHT way to modify the code for LabVIEW and run it and obtain data? Thank you:

    function CapturePulseV(pulseLevel, pulseWidth, pulseLimit, numPulses)
        if (numPulses == nil) then numPulses = 1 end
    
        -- Configure the SMU
        reset()
        smua.reset()
        smua.source.func            = smua.OUTPUT_DCVOLTS
        smua.sense                  = smua.SENSE_REMOTE
        smua.source.rangev          = pulseLevel
        smua.source.levelv          = 0     -- The bias level
        smua.source.limiti          = 5     -- The DC Limit
        smua.measure.autozero       = smua.AUTOZERO_ONCE
    
        -- Use a measure range that is as large as the biggest
        -- possible pulse
        smua.measure.rangei         = pulseLimit
        smua.measure.rangev         = pulseLevel
    
        -- Select the fast ADC for measurements
        smua.measure.adc            = smua.ADC_FAST
    
        -- Set the time between measurements.  1us is the smallest
        smua.measure.interval       = 1e-6
    
        -- Set the measure count to be 1.25 times the width of the pulse
        -- to ensure we capture the entire pulse plus falling edge.
        smua.measure.count          =
                        (pulseWidth / smua.measure.interval) * 1.25
    
        -- Prepare the reading buffers
        smua.nvbuffer1.clear()
        smua.nvbuffer1.collecttimestamps    = 1
        smua.nvbuffer1.collectsourcevalues  = 0
        smua.nvbuffer2.clear()
        smua.nvbuffer2.collecttimestamps    = 1
        smua.nvbuffer2.collectsourcevalues  = 0
        -- Can't use source values with async measurements
    
        -- Configure the Pulsed Sweep setup
        -----------------------------------
        -- Timer 1 controls the pulse period
        trigger.timer[1].count          = numPulses - 1
        -- -- 1% Duty Cycle
        trigger.timer[1].delay          = pulseWidth / 0.01
        trigger.timer[1].passthrough    = true
        trigger.timer[1].stimulus       = smua.trigger.ARMED_EVENT_ID
    
        -- Timer 2 controls the pulse width
        trigger.timer[2].count          = 1
        trigger.timer[2].delay          = pulseWidth - 3e-6
        trigger.timer[2].passthrough    = false
        trigger.timer[2].stimulus       =
                    smua.trigger.SOURCE_COMPLETE_EVENT_ID
    
        -- Configure SMU Trigger Model for Sweep/Pulse Output
        -----------------------------------------------------
        -- Pulses will all be the same level so set start and stop to
        -- the same value and the number of points in the sweep to 2
        smua.trigger.source.linearv(pulseLevel, pulseLevel, 2)
        smua.trigger.source.limiti      = pulseLimit
        smua.trigger.measure.action     = smua.ASYNC
        -- We want to start the measurements before the source action takes
        -- place so we must configure the ADC to operate asynchronously of
        -- the rest of the SMU trigger model actions
    
        -- Measure I and V during the pulse
        smua.trigger.measure.iv(smua.nvbuffer1, smua.nvbuffer2)
    
        -- Return the output to the bias level at the end of the pulse/sweep
        smua.trigger.endpulse.action    = smua.SOURCE_IDLE
        smua.trigger.endsweep.action    = smua.SOURCE_IDLE
        smua.trigger.count              = numPulses
        smua.trigger.arm.stimulus       = 0
        smua.trigger.source.stimulus    = trigger.timer[1].EVENT_ID
        smua.trigger.measure.stimulus   = trigger.timer[1].EVENT_ID
        smua.trigger.endpulse.stimulus  = trigger.timer[2].EVENT_ID
        smua.trigger.source.action      = smua.ENABLE
    
        smua.source.output              = 1
        smua.trigger.initiate()
        waitcomplete()
        smua.source.output              = 0
    
        PrintPulseData()
    end
    
    function PrintPulseData()
        print("Timestamp\tVoltage\tCurrent")
        for i=1, smua.nvbuffer1.n do
            print(string.format("%g\t%g\t%g",
                                smua.nvbuffer1.timestamps[i],
                                smua.nvbuffer2[i],
                                smua.nvbuffer1[i]))
        end
    end
    

    I finally solved it myself! I first create support shell, according to the documents, but the problem was with functions of scripts but I solved by introducing VISA separate, feature writing and THEN retrieve the data from the instrument directly by VISA buffer read more. I did TSP_Function Script Loader that allows simply copy/paste codes teaspoon (any * .tsp) of: TSB program or incorporated into this type of function and loader.vi, name (parameters), defined by its own pasted script then it will generate RAW files directly in the array of strings that can be broken into pieces or restructured into what you want as for the graphics, etc..

    That's all I really need to do, I can do codes of tsp in LV and get the data off of it easily via the function defined. Now, this Loader.VI behaves in the same way that TSB keithley-made program I use.

    Here I add Loader.vi Script TSP_Function (in LV 2011 +).

  • Function of zero crossing

    Hello

    I found this passage function to zero in one of the old forums and I'm trying to understand how it works. In my case, I have two sine waves, instead of a square pulse but I can really understand how this feature works. I know that the first, the waves are generated, and then you get their attributes, data values are in the detector of passage over who controls the case statement but I do not know how the trigger time and interaval are used to build the table, I think that the timestamp outside of the loop 'for' is for the storage of the previous itteration zero crossings , but I'm not really sure. I have no idea what is happening at the final stage before the time of transition to zero are subtarcted, as in the table of threshold and so on. I read how each function separately, but I can't add the blocks together.

    So I was wondering if someone could explain how it works?

    Thank you

    Add to what crossrulz said, it helps to understand what is the code you are looking at.

    Apparently you don't understand quite what the t0 and dt.  T0 is the time at the starting point in the waveform.  There can be a wide variety of time instead of just 0.  DT is the time interval between samples.  If we multiply by dt iteration, we know how much time has passed since the first sample.  After 0, 0dt is identical to 0 s.  From there on, 1dt, 2dt, 3dt, etc. can all be calculated for a measure of time value.  But, it measures only 'time in the first sample."  If it measures only that the timestamp can be empty.  If you want to convert the time from the first sample a real time, you must add the initial time.  For example, if dt is 1s and t0 is 16:00, after 3 samples we to 2dt up to 2 seconds.  Does worry about 2 seconds or 04:00:02

    The 'picture of big timestamp' is fed into what we call a shift register.  You can use this registry to pass values between the iterations of a loop.  Before the loop, we feed a table not initialized in the shift register.  The first time that the construction is used, he fed an empty array and the timestamp to record first.  It is then output to the shift to the right of the loop register.  This value is passed to the next iteration.  It will continue until we reach the table of construction for the second time.  Now, table 1 element is introduced into the upper entrance of the table build and a new timestamp is added at the end of the table.  This will continue with the array of size n arriving at top of entry and the most recent timestamp is added at the end to make an array of size n + 1.  If we want to keep all the timestamps, we like this logic.  You could plug it into the bottom and the timestamp again upward.  That would put the most recent timestamp in the first element of the array.  You just want to include the old array so keep you all the timestamps instead of just the most recent.

  • VMware Performance event triggers use case issues.

    1) can event Performance adapter CPO VMware triggers and their

    Attributes of the SAMPLE SIZE, INTERVAL and CONDITIONS be configured

    for the following use cases?

    (2) event VMWare Performance triggers may be CORRELATED?  and if so it would take to satisfy the use case?

    (3) an additional performance monitoring tool needed to satisy the use case? :

    If a VM CPU or RAM was 80% for 2 hours then trigger a workflow

    and

    If a VM CPU or RAM was 60% for X days and then trigger a workflow

    First, I will describe how you can instrument a correlation method, but in the end, I'm not sure it's really necessary for use cases described.

    To correlate the performance VMware on a designated period events, you would create a process correlation that follows the underlying the performance event and decides to trigger the process wished triggered when correlated event is detected or not.

    Here's how it works.

    First, create a global table with three columns:

    (1) virtual path Machine

    (2) County of consecutive trigger

    (3) latest trip time

    Create a process that is triggered by a performance event VMware (for example memory Avg > 80%) where you can set the size of the sample and an interval that is logical view of the period of interest (2 hours or X days). For example, a sample of 10 and 30 seconds (5 minutes) are a slice of reasonable time to vCenter for 2 hours. As a result, requiring 24 consecutive triggers to trigger the real event of interest. (divided by 5 minutes to 2 hours)

    In other words, the formula is:

    Sample size * interval / calendar = consecutive trigger Count

    The correlation process triggered by the gross VMware event does the following:

    (1) if there is no existing entry in the overall table for the virtual machine, add the entry to table with count = 1 and current time

    (2) if the entry exists, check the current time against the last trigger time

    (a) if it is the next interval, for example, the time now is 12:15 and triggered last time was 12:10 (see note below).

    Incrementing counter and trip together last time

    If count = 24, then run the process that manages the "VM memory Avg > 80% for at least 2 hours' and remove the entry from the table.

    If count< 24,="" the="" process="" exits="" having="" only="" incremented="" the="" counter="" and="" set="" the="" last="" trigger="">

    (b) if the current time is > that last trigger time slice schedule (+ a little padding), set the counter to 1

    Note: When comparing the time of w/last time running, you should cover to consider delay light treatment in order to compare now< last-time+(time="" slice*2).="" anything="" less="" than="" 10="" minutes="" in="" this="" case="" would="" be="" considered="" a="" consecutive="" trigger.="" you="" could="" also="" compare="" current-time="">< last-time+time-slice+1,="" which="" is="" probably="" also="">

    Now, after going through all that, you don't have to the process of correlation after all. Simply adjust your sample size to be large enough to accommodate your deadline and you launch your handler directly without having to correlate. So for the 2 hour window, simply create a sample size 240 (* 30 seconds = 2 hours). This may or may not work depending on how performance indicators have been set up on the server (sample size, intervals and how much is saved). You can define your own samples and multiples of these configured values intervals (so be careful and see VMware documentation when he resorts to such measures)

    You can see that I have described everything first correlation method is more reliable, especially for longer periods such as X days (where you need to taste every hour instead of every 5 minutes).

    In any case, I think you can do what's needed without external control, but will require experimentation and a deeper knowledge of the works of performance for ESX metric sampling.

  • How to disable a scheduled through database task?

    I would like to know to disable the scheduled without IOM task running, preferably through the database.

    IOM's out the box configured schedule tasks to run at startup of IOM, and I would like to avoid that from happening.

    Is is possible to disable these tasks when IOM is not running?

    If possible, I would like to know what I have to do, preferably through the database

    The QRTZ92_TRIGGERS table contains the trigger time and schedule tasks. You can directly change the value of START_TIME and NEXT_FIRE_TIME columns to dates in the future in order to prevent the work planned to start.

    You can also stop the job scheduler, which is responsible for the kickoff of the planned work.

    To manually stop the job scheduler, go to http://OIM_HOST:OIM_PORT / SchedulerService-web/status

    You can configure the IOM - config.xml so that the scheduler does not start at startup of IOM.

    Reference: scheduled tasks management

    To disable a scheduled task, you must have the IOM running. You can use the APIs, change calendar tasks (fake) metadata, or use the user interface to disable the calendar tasks.

  • WARNING Disk_Usage

    I get this message, any idea why? Everything seems to be running esx 3.5 have about 30 VMS on that host, but I still get this messgae everyday. We have enough disk space...



    Thank you

    Express

    EXPRESS wrote:

    Well, it's that he didn't y no backups running, and even if I recognized the alarm it it still shows with a warning. It's the only host with the warning of 7 guests.

    Recognizing that the alarm will not change its status, it stops just the alarm trigger time and time again.  You must reset to green to clear it.

  • Move several meanings in the football game...? !

    Hello

    I create event simple keyboard to move the ball/player on the right, left, up-down. Let's say that the user click arrow to climb after he press the arrow to the right that always supported while on the arrow top to move right to the top and if he releases the arrow only hurry up while still arrow right he will move to the right only. How can I do this?

    function SoccerMove(e:KeyboardEvent):void {}

    if(e.keycode == 37) {}

    SoccerBall_mc.x-= 5;

    } else if(e.keyCode == 38) {}

    SoccerBall_mc.y-= 5;

    } else if(e.keyCode == 39) {}

    SoccerBall_mc.x += 5;

    } else if(e.keyCode == 40) {}

    SoccerBall_mc.y += 5;

    }

    }

    stage.addEventListener (KeyboardEvent.KEY_DOWN, SoccerMove);

    Kind regards

    due to multiple keys and synchronization problems (due to the incompatible keyboard repeat rate and trigger time), use:

    var left: Boolean;

    var right: Boolean;

    Var high: Boolean;

    var down: Boolean

    function downF(e:KeyboardEvent):void {}

    if(e.keycode == 37) {}

    left = true

    } else if(e.keyCode == 38) {}

    up = true

    } else if(e.keyCode == 39) {}

    right = true

    } else if(e.keyCode == 40) {}

    low = true;

    }

    }

    function upF(e:KeyboardEvent):void {}

    if(e.keycode == 37) {}

    left = false

    } else if(e.keyCode == 38) {}

    up = false

    } else if(e.keyCode == 39) {}

    right = false

    } else if(e.keyCode == 40) {}

    low = false;

    }

    }

    function loopF(e:Event):Void {}

    {if (Left)}

    SoccerBall_mc.x-= 5;

    }

    {if (Right)}

    SoccerBall_mc.x += 5;

    }

    etc.

    }

    stage.addEventListener (KeyboardEvent.KEY_DOWN, downF);

    stage.addEventListener (KeyboardEvent.KEY_UP, upF);

    this.addEventListener (Event.ENTER_FRAME, loopF);

  • Limit bpm 11g event

    all,

    I need to use the time limit of event (timer events) in my process, but the time is dynamic.

    in aid of bpm, I have seen this, but don't works.

    'now' + 30 me

    Deadline - "1 day"

    arrivalDate.dateTime + "1 hour"

    someone knows the simple exp or exp correct xpath?

    TKS.

    You can set timer with "Hourly" (periodic) events or triggers 'Date time' (once)

    If you use the trigger of the 'time Date' (once), you can specify any Simple Expression that returns a DateTime value. As for example:

    'now' + '30m'
    
    dataObjectTime + '2h'
    

    If you use the (periodic) trigger 'Time Cycle', you can specify simple Expressions that returns an interval/duration. As for example:

    '1h30m'
    
    dataObjectInterval
    
    dataObjectInterval + '30s'
    

Maybe you are looking for

  • Firefox automatically opens the new tab, even when I don't want it. Need to stop this.

    In the Blackboard, I need not to open a new tab in Firefox. Before the last update, it was fine, but now when I click on a new choice (that is, the notebook) it always opens a new tab. The administrator of my Bb says it's a browser problem. I can rig

  • Need a replacement to break links more

    I love. As always, this addon is disabled once again.What addons provide the same functionality, i.e. "to highlight multiple links and open them in tabs. Yes, I could do another search of 60 minutes and the analysis, but I already did 3 times before

  • 10.10.5 version

    Bluetooth is not available I have restart my computer and it does not work please help

  • PHP through CGI Error 500 - IIS

    Hello, I have a question for IIS. Windows 2008 R2(x64), IIS 7.5, PHP 5.3.9(with Visual C++ 2008 Redistributable x 32) + CGI,Site created on CMS Joomla 1.7.0When I login to the Admin Panel and go to global settings - there is error #500. Error log is:

  • pozofoho.dll and load nipovine.dll error

    When I start my computer I get two error messages: nipovine.dll and pozofohu.dll has not been found. I use windows xp. What is is?