trigger

Hi all

I am currently working on the inspection of labels using the vision.

It is necessary to open and close each loop camera? I want to configure the camera triggering mode once and start getting the nod to each trigger. Anyone can please modify the vi attached below.

To understand it please check the attached vi.

Waiting for answer

Thanks in advance,

You can open and close once. (it is open before you launch the while loop and shut down after the while loop)

Tags: NI Software

Similar Questions

  • How can I create a trigger e-mail messages sets a phone when Gets an email from particulry?

    Hi team, support
    Customer email thunderbird whit, how can I create a trigger e-mail messages rule a phone dial when comes a word of the body particularly E-mail?

    Kind regards
    Alessandro.

    I don't think you can do this with ordinary Thunderbird. But this add-on

    https://addons.Mozilla.org/en-us/Thunderbird/addon/FiltaQuilla/

    allows you to run javascript or IIRC, launch an external program when a given filter condition is met. So this does not exactly provide an answer to your question, but allows a possible solution. '

  • I can't get the move animation to automatically trigger the next slide

    Hello

    New to Keynote. I wonder if there is a way to trigger the next slide to load after doing an animation out, that does not involve having to make an additional click? For now, I have text that moves transition and get him out on click, which then leaves me a blank screen, rather than the transition to the next slide.

    Pointers or help with this would be really appreciated.

    Click the background of the slide from the slide that has the text animation: Inspector > Animations > Transitions:

    the value of the drop of Transition start automatically

    Enter an amout for the delay, if any

  • MainStage stop drums trigger keyboard

    OK I have an Alesis V61 and MS3. It has 8 pads of the battery. I want to set up a very simple patch where all 61 note keyboard triggers ONLY a piano patch. I want one of the Eb trigger pads (2) - a handclap.

    I have 2 strips of channels, Yamaha Piano and Bluebird Drum Kit. The strokes I started with success of the drum pad. Everything is good. BUT the keyboard also plays samples of Bluebird, which is not good! How to stop the notes on the keyboard trigger the Bluebird Drum Kit samples? Thank you guys

    HA! After 3 hours of tinkering it worked (for me anyway). In the channel strip Inspector, MIDI input set none - kills the keyboard trigger the sample but not the pad... against intuitive but worked for me! Hope this helps someone else

  • Present the version 7.0.1 download available for 8.0.1. Trigger the update begins a charge down and ending. Download and then 'connect to update server' that never connects. This has happened over a period of 2 weeks.

    My 7.0.1 program tells me there's an update available, 8.0.1...
    I trigger the update that downloads an installation program.
    When I restart firefox to get the update installed, restart and triggers a new window indicating that it contacts the server to update. This will continue to get in touch for 30 minutes with no established connection.
    To keep my browser to 7.0.1.

    Windows Vista Ultimate sp2 64-bit.

    Try the alternative and more simple way to download from here and simply run

  • Midi trigger

    I think to migrate from protools to logic, but there is a function that I don't see on the parameters of logic

    can I start to record from a midi or key elements?

    How can I do that.

    Thank you

    Yes you can - you can learn any assignment of midi keys to trigger the main controls (and recording is one of them).

    Below, I attributed a C2 key on my Midi Controller impulse to start the registration process...

    Click on the image if it does not work...

  • My existing flash has a 12 trigger voltage, 2V. Is it dangerous to use on a NEX6?

    After testing, my existing flash has a 12 trigger voltage, 2V. This will be acceptable to my claw NEX6?

    After the Sony specification flash search box and enter a request, I found that Sony does not encourage a trigger voltage of above 6 volts. I'll take that as a response that my flash voltage of 12,4 to endanger my NEX 6 trigger.

  • How to trigger the dictation from the smart keyboard on the iPad pro.

    I use dictated on my iPhone and my iPad quite often.

    However on my new iPad Pro with the smart keyboard attached, I do not how to trigger the dictation from the keyboard.

    I don't see how to get the soft keyboard back to press the button of the microphone are there, such space suggested by some on this forum.

    This doesn't seem to work in the latest iOS Update 9.

    I would be fine with a hotkey, or have to invoke the keyboard of the shop, then press the button of the microphone, but I don't see how do either.

    When the Emoji button on the keyboard smart strike as the keyboard, the software keyboard emoji is displayed, the space but when I press the soft ABC capital but I cannot get to the regular keyboard with the microphone button.

    A possible alternative would be to use Siri to dictation trigger in recording a memo or another application, space but I didn't understand how to do this job either.

    Has anyone experience this problem and found a solution?

    Unfortunately I had to spend a good hour on the phone with technical support when they finally admit that it was an oversight by Apple.  I hope someone reads this post until they spend countless hours trying to understand something, but has no solution at the moment. Frustrated!

  • 5154 PXI trigger on the external input

    I use a PXI-5154 and want to change my previous program to trigger the external source. I'm feeding the external source from source to V 2.5 and it seems to trigger fine. However when data acquisition the vertical range of the oscilloscope will 5 V which is too high as to my request I acquire in the millivolts range. I tried to show the vertical range of the channel I acquisition, but although I put it as the active channel I get the following error:

    Error 1074118616 has occurred to the property node (arg 1) in PD_measurements_v11_test.vi

    Get a base attribute value channel failed because the channels interviewed have different values.  Please specify a channel when you query a string based attribute.

    I enclose you a printsceen of the relevant part of the code.

    Kind regards

    Karavellas

    Dear Tunde

    I managed to make the changes you suggested and the works of the example. I'll look in my code and see what the problem is. I'll get back to you if it has been fixed in my code or not.

  • Electric trigger DAMA IQ & check for new records to collect an infinite number of records

    Hi all

    I have some difficulties with the help of the trigger edge power IQ & questioning the DAMA if it has samples/records ready for pick up.  I have reviewed the documentation on the support to the screw and the examples provided with the driver of the ACCA and have not been able to solve my problem on my own.    What I'm trying to do, is to have this VI capture periodic RF bursts that are larger than a specified threshold.

    I go to this topic in the following way:

    I put the number of samples I captured (finished) for each burst which crosses the threshold
    I put the number of records to capture to be infinite
    I said that the rising slope and the appropriate threshold
    I have then to validate the configuration of the ACCA and start acquiring
    I have then go into a loop and check the backlog of samples as well as the acquisition is
    If either of the above is true then I get the samples with the IQ extract complex WDT vi
    I continue looping until the user stops the vi with a button on the front panel
    I went on this path that I didn't block indefinitely or for long periods of time

    What I see is:

    I'll take one shot and then nothing else
    what the samples never back above zero
    that acquisition is ever complete
    If I switch out the IQ extraction with equivalent IQ reading and ignore the completion back & I get documents like I expect

    My understanding is as follows:

    Electric trigger IQ does not have to be re-armed in VI
    that each trigger to fire IQ Power will create a new record containing the number of samples that I asked

    My questions:

    It seems that when the number of records is infinite that the acquisition is never considered as carried out when the State of the acquisition is verified, is that correct?
    I receive multiple records pending upward on the ASB using this configuration?
    Why a record number is provided with the back of fetch get VI?
    Why would I pick any folder, but the record of zero?
    I'm doing something wrong here?
    Is there a better way to do this?
        
    Thank you
    Russell

    Hi Russell,

    You are on the right track to get your application do what you want. Instead of check to fetch back, I suggest that lets you read the property node DAMA the "' Acquisition > Fetch > Records made" property to know when a new record was acquired. "

    > it seems that when the number of records is infinite that the acquisition is never considered as carried out when the State of the acquisition is verified, is that correct?

    That is right.

    > I get multiple records pending upward on the ASB using this configuration?

    Yes

    > Why a record number is equipped with the rear of fetch get VI?
    > Why would I pick any folder, but the record of zero?

    You ask DAA for an infinite number of records. File 0 started the first trigger seen. Record 1 to the second outbreak (end of disk 0) and so on.

  • Restart waveform immediately start trigger

    I create a waveform 50 ms with an SMU-5451 in SMU-1078 chassis with a controller of SMU-8840 running Labview RT.  The waveform is currently triggered by a pulse of a counter of data acquisition because the timing of the wave must be closely synchronized with data on the acquisition of data collection.  However, this approach is problematic because it is difficult to produce a continuous of the 5451 signal when it is triggered in this way.  If the waveform is exactly 50 ms long, will miss the start trigger.  I can tolerate losing at the end of the wave, but I can't tolerate having a gap in the output, and I need the waveform to start exactly on the edge of outbreak of 50 ms.  I can configure the 5451 to accept a trigger start and restart the wave immediately rather than wait for the current iteration of the waveform to complete?

    I guess I could use a complete the 5451 event to trigger the acquisition of data instead, but I guess there is a way for me to do what I want.

    Are you familiar with the mode "script"? You might be able to use this example script:

    script restartWhenTriggeredScript
    Repeat forever
    generate wfm
    break on scriptTrigger0
    Repeat forever
    generate wfm
    end repeat
    end break
    end repeat
    end of script

    Basically, the idea is that, when it receives a trigger, it stops the execution of the inner loop and finish the iteration of the outer loop. Then it will start again from the beginning and to the inner loop.

    Please let us know if that fixes the problem.

  • trigger digital output myrio

    Hello friends,

    I have a question. I need to trigger an output of Myrio with a single pulse. After the pulse, the output will remain active. Then with another single pulse, the output will be switched off. Should what tool I use?

    Thanks for listening,

    Kind regards

    David

    Hi Davi08,

    I did a little research for you answer and I found another "NI Discussion forums" forum that maybe can help you.
    Try using this link, I think this will help you.

    http://forums.NI.com/T5/academic-hardware-products-Elvis/myRIO-digital-trigger/TD-p/3278560

    Best regards

  • DMM trigger expire 2000msec

    Hello

    I use a DMM4070 and "SoftwareTriggeredMultipointAcquisition DotNet example."

    I want to trigger the DMM4070 with the AuxTrig entry to the front of the instrument.

    How can I change the time out the of triigger?

    It is now on 2000msec. I want to set this to 10 sec.

    When I us the example and do not trigger within 2 seconds, I get error message saying:

    ModularInstruments.NIDmm: The operation did not complete in time maximum allowed. Timeout: 2000mS.
    Error code:-1074126845

    Thanks in advance

    Wissam

    Sorry

    Wrong forum

  • Mounted daqmx calendar/trigger on 2 chassis mxi-express

    I have 2 chassis SMU (including one with a RT controller) connected with SMU-SMU/8384-8381-MXI-express boards.

    I can see all the devices in both chassis and can configure DAQmx tasks in each chassis individually, but I can't create any single task with a device of two chassis. When there is a feature of two chassis in the task, I get:

    Error-89125 occurred at DAQmx start Task.vi:7220002

    No registered trigger could be found between the devices in the range... Make sure that there is a trigger line available on the bus triggering shared between devices.

    Is this possible in the software? Or should I add material?  I can't find any docs or examples on this subject, other than a promising article on Veristand (ni.com/white-paper/14637/en/, #2) but I can't implement in MAX or NV. Timing is not critical (50 to 100 ms is very good), I just need many devices on 2 sites, so the MXI solution seems to fit in. I thought the solution was to use the local clock on each chassis and set up a trigger shared/exported, but impossible to find something that works.

    Thank you!

    Hey brimcd,

    You are right; It is not a way to send a trigger between chassis without timing card.  This link goes into a bit more detail: http://digital.ni.com/public.nsf/allkb/D91582EBF0810F4486256E70004E4145

  • How to delay a PXI-5122 trigger before routed to string of PFI

    Hello world

    I use a PXI-5122 in a PXI chassis. I want to synchronize with two external devices. The first will send a trigger (with a 10 Hz repetition rate) for PXI-5122. Then PXI will generate a trigger (with a constant delay) in the second.

    It seems that I need to generate a trigger, then export this trigger to PFI 0 line, but I do not know how to delay triggers with a timeframe of 4µs. I read that there is a slight delay between a trigger on the PFI and the first sample. And the length of the cable is also an important factor to consider.

    Could someone give me some suggestions?

    Wednesday,

    Thanks for the drawings, that helps a lot!  Somehow, I see this work (how to set up the scanner):

    1. set up the record length to be 12us (4us trigger samples, 8us after outbreak).  If the sampling frequency is 100 ms/s, that would be a record length of 1200 samples.

    2 configure the position of record reference to 33%.  That's how the digitizer breaks 1200 400 samples according to trigger before triggers and 800 samples.

    3. configuration of triggering immediate reference.  This will allow the acquisition of trigger the moment she gained 400 before triggering samples.

    4. export the "reference trigger (Stop)" to send to Device_2.  This output pulse is of variable width, so if you want consistency, you will need to the Device_2 trigger the rising edge of the pulse, did not not fall m.  Once 400-pre-trigger samples are acquired, this impulse will be sent, and then the scanner will be immediately habitable after initiation of sampling.

    5 configure the trigger of the entrance of Device_1 (10 Hz trigger), as the 'Advance trigger' and 'Start Trigger'.  This will make the digitizer wait this impulse to start sampling before the next record.  We set up, the relaxation of beginning to the 1st record and the trigger in advance for all subsequent records.

    This facility should allow a pretty decent timing, but please test to be sure that it will be sufficient for your application.

    Kind regards

    Nathan

  • Are there examples of niScope send software trigger edge

    This is the sub VI:

    In my case, PXI-5105 and 6368 are used for the acquisition of synchronization. Post_trig_event and pre_trig_event of data are needed to analyze what analog channel has abnormal evolution. The trig source is not unique, which include several analogue channels. I therefore prefer to use a software to process a lot of data to channel to find the abnormal change and then send a trig signal, which means a trig signal to the PFI or the PXI_Trig. I think that the noScope that send software Trigger Edge works. Can you give me an example of this subroutine VI?

    I've attached an example that uses a software trigger to trigger an acquisition.  The code shows how to use the "niScope Trigger.vi software Send."

    Description of your request, it looks like you want to acquire data continuously and perform a top treatment in LabVIEW to determine when send software trigger.  This can also be done, and I would recommend starting with one of our continuous streaming of examples, like "niScope EX Fetch Forever.vi", which can be found using the example Locator OR under material input and output > Modular Instruments > NOR-SCOPE > Acquisition continues

     


    I hope this helps!

    -Nathan

Maybe you are looking for

  • Beri face para ideapad s400

    Hola quiero saber y alguien m could desire such an el ideapad s400 is can put el bery face of lenovo tengo windows operating system 8 donde puedo descargarlo as sirva el windows 8?

  • How to install the drivers for the hp deskjet F4500 wireless printer?

    Troubleshooting says I need to install a driver, my printer is offline and I am unable to do it online. He showed this: Hp color laserjetCp2025dn no driver and hp deskjet F4500 no pilot, said to install the drivers, but I don't know how to do this, a

  • update firmware on chassis battery blade PC8024-k?

    I tried to update the firmware on a stack of switch PC8024-k 2 5.1.5.1.  After the update, this is what I get: Unit image1 image2 current-next active---- ----------- ----------- -------------- --------------1 5.1.2.3 5.1.5.1 image2 image22 5.1.5.1 5.

  • Max resolution R61i problem

    Hello world. I'm having a problem with a R61i 8930-A97: I can't put resolution is bigger that 1280 x 800 resolution GMA965 max is thus higher. Any suggestions?Thank you.

  • Get some of the XML

    Hello friends I had a chunk of XML. I need to get some of the XML for that. for Ex 123456789 I need to write a method that I can pass a node (Ex: author), can I get a new XML that has part of the XML like this 123456789 How to do this? Help, please