try to secure my connection
Hello
Recently, after a power outage, my router started connection on the Linksys network that is not secure. I had set up my own personal network and connected very well until this Division of power. I lost my installation CD and I can't open the download file type that I receive from Linksys.
So, I'm running on an unsecured Linksys network. My home network is always on the list, but I can't connect to it.
What I would do. I have a Breakfast & bed, and I can't afford to run on an unsecured network.
Thank you
Perhaps because of the loss of power, your router settings must have reset to zero and that is the reason for your network unsecured wireless...
To secure your wireless network, you don't need to have a Setup disk, you can manually configure all the settings on your router...
Wired computer to the router by an Ethernet cable, open a page in Internet Explorer browser on a computer hard wired to the router... In the address bar type - 192.168.1.1... Leave name empty username & password admin lowercase usage...
Once you connect to the router configuration page, you must click on the tab 'Wireless' and below, you can change the "Wireless Networks SSID name" in your name and change the channel to 11-2 wireless, 462 GHz and allow the broadcast of the SSID should be activate and click on save settings...
Then, you click the sub-tab "Wireless Security" and in the window, you can enable security on your router. Select "WPA Personal" and the WPA Shared key enter your security key and click on save settings...
Now, you can try to connect to your wireless network.
Tags: Linksys Routers
Similar Questions
-
Unable to access secure Internet connections
I have my laptop series satellite has recently stopped for allowing me access to secure Internet connections. When I spoke with my Bank's online support, they identified that I will need to reinstall the xp home operating system and it will get it back. Only thing is, is that it came pre-installed, and I did not all discs...
I don't want to pay a bomb buy new XP - any suggestions on how I can make low-cost cela? I get a new digital / provider internet tv etc Thursday the engineer came to the House to install it and I need to have this problem before it happens (this leaves me a day and a half!)
Help! Thank you! :)
Hello
Try to contact Toshiba service partner allowed in your country and order the original CD from recovery for your unit. I'm sure that it will not cost you much.
You can find the address under http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true
Good bye
-
Original title: SECURITY WARNING
When I try to open a program I have getthis message:
"Do you want to view only the webpage content that was delivered safely.
"the Web page content that willl be sent using a secure HTTPS connection, which could jeopardize the securityof the entire Web page.
Is this something that needs to be corrected? If yes how.
Hi billkabay,
(1) program which you are referring?
(2) is the problem confined to this specific programme?
(3) since when are you facing this problem?
This problem normally occurs when you open Web pages in internet explore. Please specify if this happens when you open a program or opening a Web page or link in internet explore.
You can see the steps in the link below
Also see the steps by Vincenzo Di Russo (check the post Saturday, May 30, 2009 11:36) in the link below.
Thanks and greetings
Ajay K
Microsoft Answers Support Engineer
***************************************************************************
Visit our Microsoft answers feedback Forum and let us know what you think. -
Original title: how access key USB secure Windows vista
I have a lexar player sure to jump that I used with an old computer that has Windows XP. I now have a new computer with Windows Vista and I can't access the secure part of the USB key. When I try to access the part secure the USB key I have the following message "Application [-10004] could not find any JumpDrive Secure device connected to your system. Please make sure that your JumpDrive Secure device is inserted into a USB port".
Of course, the USB key is inserted into the USB port. If anyone can help find me a way to access the part secure the USB key I would appreciate it. Thank you.
Hi Jon0909,
The error that you received can be for several reasons. I suggest you try the following steps:
Method 1: Run the fixit available in the link below and check if that makes a difference
Tips for solving problems of USB devices
Method 2: This normal matter as a result of a conflict between the USB and other USB (Universal Serial Bus) connected to the computer.
(a) disconnect all the external devices connected to the computer to expect the mouse and keyboard, check if your USB key works.
(b) If this solves the problem, and then add back both devices until you discover the piece of hardware causing the issue.
If the problem persists, you can contact the manufacturer of the device for any known issues
http://www.Lexar.com/supportThank you, and in what concerns:
Ajay K
Microsoft Answers Support Engineer
---------------------------------------------------------------------------------------------------------
Visit our Microsoft answers feedback Forum and let us know what you think. -
Securing internet connection Wi - Fi with Equium L10 and Belkin router
Hello
I installed a wireless belkin router on my laptop L10 and have an excellent connection to the internet - everything works fine. However, I would like to secure the connection to prevent indiscreet listening - I tried to do this under the encryption and authentication of the menus, but I'm not sure about the different acronyms used - eg Shared, WEP and WPA for example.
I tried different combinations of these, but the laptop disconnects just from the router until I return to the connection 'open' standard with encryption disabled. Can someone point me in the right direction... ??
Hello Dan
Your router is unknown to me, but encryption is still working on the same path. Check the security settings of your router, then select security options. Set the encryption you want to use (WEP) and the password.
Your device must be configured as described on this page
http://LSS.wisc.edu/~Sara/wireless/pcwepconfig.htmIf everything is done on the right track to avoid any problems. I also use WIFI at home with 64-bit encryption, and I spent 10 minutes for any configuration.
-
I was told that all security USB connections is disabled in the BIOS. The only controls for this PC is USB ports for mouse and keyboard control ect. How can I get into the bios without keyboard and mouse in operation? There is no other way to control this model computer. The only connections on this PC is only the USB connections. Again, if I can get somehow get into the BIOS I can enable security USB connections as it should.
UPDATE,
Fixed a problem.
I have install a market after card bipassing USB bios usb connections. I went in the BIOS and turned on USB connections. I figured out the EASY DIFFICULTY and solved the problem myself. No other technology needed in this case.
Very EASY SOLUTION!
Thank you
-
I get an error pop-up that says that Web page contains content that is not delivered using a secure HTTPS connection, but likely to compromise the security of the entire webpage, whatever that means
In "BOLD" on the very top of the ther security warning she also ask you want to view only the webpage content that was delivered safely?
original title: HTTPS connection issues
You are using Internet Explorer 8?
This article describes the causes of this message and how you can remove:
http://blogs.msdn.com/b/ieinternals/archive/2009/06/22/HTTPS-mixed-content-in-IE8.aspx
Information on the changes in Internet Explorer 9 is available here:
-
my computer wouldn't let me download lime wire... and every time I try a security alert appears.
Hi juannfallen,
Welcome to the Microsoft community newsgroups. I suggest you try these options:
The question can be caused also by your security program such an antivirus or a firewall of Windows /Defender that can have conflicting parameters as to not not to perform certain tasks. I suggest you temporary disable antivirus and firewall and check the result again. You must activate new security that you was disabled programs.
For more information, visit the Microsoft Web sites at the following address and check if the Windows or Windows Defender firewall is causing this problem. It is suggested to make changes and to allow certain applications to run through these by the use of exceptions rather than turn them which can cause serious problems for the security of the computer:
1 explore the features: Windows Firewall
2. turn Windows Firewall on or off
3. Understanding Windows Firewall settings
4 explore the features: Windows Security Center
6. turn Windows Defender on or off
7 Windows Vista: antispyware software - Microsoft Security
8 real-time protection real turn Windows Defender or disable
If the problem persists, return with the following details:
1: name of the security of the software
2: exact security alert
Let me know if it works. Good luck!
Hope this information is useful.
Thank you and best regards,
KKS Vijay
[If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]
-
Is it possible to have a secure FTP connection using private key authentication?
Is it possible to have a secure FTP connection using private key authentication to connect to a folder on Business Catalyst?
Hello
Not available at this stage that the only options are in the article to Setup SFTP.
- http://helpx.adobe.com/business-catalyst/partner/connecting-site-using-ftp-client.html
Kind regards
-Sidney
-
Z10 Z10 blackBerry does not start since then try a secure erase
I had problems where none of my text messages have been moved during the previous Blackberry, such as reported earlier today. I was also disappointed by the speed of handset, BBM for example would take at least 5 seconds to load (now on my old torch), so I made a secure erase so I could try the installation again. This seems to have been a mistake, as the handset now does not start. I see "Blackberry" appear for a second, then get a logo that seems to be asking me to connect the unit to a PC. It does nothing - the PC does even not record that a device has been plugged in. After a minute or so, the screen fades and the handset appears just to turn off. I'm very disappointed in my first day with the handset - far from a smooth experience as it should be, I was left the impression that OS10 is still in early beta development.
What can I do to remedy this?
kb33480 should help you.
-
No secure WiFi connection. Need firewall software?
my wifi connection is not safe here, believe so I need to install a firewall on iPad software to enable my email be directed to real addresses I choose to send them to, rather than, when seized upward, and the word 'send' is pressed, then this particular and other e-mail, they will directly in my "Outbox? (I suppose that this is here just for that?) For email be directed on if there is no secure connection... ?).
Is there a Web site for these firewalls in order to "liberate" these e-mails from their "blocked situation" and allow them to be redirected to the right inboxes? I would really appreciate a response to this call...?
If your mail is your Outbox and stay there, so you should receive some kind of error message. Generally, errors like this have to do with connection to your outgoing mail server. If you receive an error message, what is the exact error you receive?
-
When you try to install
Update of security for Microsoft Office System 2007 (KB973704) I keep receivingError Code: 0x8007066FHow can I fix this so I can install the update?Thanks for any help0x8007064C & 0x8007066F
This problem may occur if Windows Update or Microsoft Update cannot locate the downloaded update.
Error code when you use the Windows Update Web site or the Microsoft Update Web site to install updates: "0x8007064C.
http://support.Microsoft.com/kb/958055or download the patch for your system and install manually.
http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=c4c92d2e-e87d-446F-8d3e-8f4be10c70aa
See also: http://support.microsoft.com/kb/973704
TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.
-
When I arrived at the center of security via the Control Panel, when it connects, a statement at the top of the page indicates that the Security Center is currently unavailable because the "Security Center" is not started or was stopped. Then tells me to restart your computer and start the service Security Center and then open the Security Center again. I don't know how to start the Security Center service, and when I restart the computer, the same message appears. The taskbar do not have a Security Center icon. How can I restart it?
Russ Jensen
Off-topic for the forum "Security Essentials".
You are XP, correct?
Press the Windows key (or Start ) and R both at the same time. This will open the RUN dialog box.
Then delete/clear all entries inside RUN it, enter Services.MSC in the RUN dialog box, and then press ENTER.The list of services should be in alphabetical order. Scroll down the page until you find "Security Center". Tell us if it is started (or Virgin) and what the startup type (Automatic, manual, disabled).
Doc
-
Try to install HP Officejet 6500 wireless by using the USB connection. Installed on a network. How do I uninstall and let Windows identify as new material on a USB connection?
Turn off the broadcast of your wireless router signal. Shut down the PC. Menu using the printer configuration to remove or change the SSID. Then turn the printer off and connect it to a USB port (this implies that all the necessary software has been installed). Now turn on the computer and turn on the printer. Once the printer has been detected the turn on your router.
Never be afraid to ask. This forum has some of the best people in the world to help.
-
I don't have an icon of Ad hoc network when I try to add the connection
So I will try to set up an ad - hoc network so that I can update my other computer (no internet and I'm not lugging this thing down a flight of stairs). But I don't have any Ad-hoc icon when I go to the "establishment of connection or a network.
Control Panel > network and sharing > set up a connection or network
After the dialog box appears where he is SUPPOSED to have the option of ad-hoc connection but does not work.
I use an Acer Aspire 5920 (it has wireless networking capabilities. My friend put up the ad - hoc on his laptop computer {exactly the same model} perfectly well. Which means mine is just well... _)
How can I solve this problem?
Hello
The host computer needs two network cards (below). The host computer must be connected to the router via a card (wire or wireless), the second card must be wireless to connect to the wireless client computer.
Instead of the Ad - doc, you try one of those too.
http://virtualrouter.codeplex.com/
Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET
Maybe you are looking for
-
Finder keep it open the file even after I change the default folder
I have the problem with the default folder in the finder. A few months ago, I changed the default folder from the finder to a specific folder. Now, I want to change to the new folder. I already go to finder > Preferences > General > new poster finder
-
How restote deleted partition?
By mistake I deleted the partition of my hard drive as a result, I can not restore factory, I would clean up my memory and start a new one, what should I do?Thank you.
-
Satellite L20-100 does bus support DDR2 800?
Hello Does anyone know if Satellite L20 - 100 bus DDR2 800 support?Thank you
-
How to create the hierarchy without creating a Subvi files
Hello I have an existing LabView program that uses blocks of Subvi. I want to change it so that I can't copy files Subvi (when I transfer the program to another computer). The goal is to have a single file/program that I can copy, paste, and run on
-
How can I get the software for my keyboard model 1. 0a Wireless Comfort 1045?
Original title: http://www.microsoft.com/hardware/download/download.aspx?categary=MK Nice day! -I HAVE A COMFORT WIRELESS KEYBOARD 1. 0 A MODEL 1045 I WANT TO USE AGAIN. BUT I MOVE THE SOFTWARE. YOU CAN HELP ME GET MY KEY BOARD GOES AGAIN PLEASE. Ha