TS of HP ENVY 17-j043cl and dual channel memory

I am very happy with my new computer laptop 17-j043cl of envy, but I see it came with 12 GB of RAM, 8 GB DIMMS and a 4 GB DIMMS.

If I replaced the 4 GB DIMMS with a 8 GB DIMM caller, the memory would be in dual-channel mode, offering a performance gain, or this computer only supports single channel memory?

More concretely, the performance gain would be sufficient to justify the effort?

(Although, really, I'd probably do it if there was even the slightest advantage of performance or efficiency.) "I'm just that kind of GUY!)

Thank you!

Hello

Please find the link given below for your unit specifications shows clearly your device supports up to 16 GB. And for your question about the upgrade, it will improve the performance and speed of the device.

Link

Tags: Notebooks

Similar Questions

  • M40-101 and dual channel memory

    Hello
    can I feed my memory in dual channel mode if I have two identical? (PC2700 DDR)

    --
    Best regards
    Mateusz

    Hello Mateuzs

    It is a very interesting question. Have you already checked the BIOS settings? Is there a possibility to choose the memory Dual Channel mode?

  • SONY VAIO F Series SVF15412CXB does support dual channel memory?

    SONY VAIO F Series SVF15412CXB does support dual channel memory?  Or is it only a slot?

    I'm curious to know if I can put a second stick of RAM in there for performance dual channel.

    Hi gremark,.

    I understand you want to be sure of everything. I checked the service manual for this model and even tried to open a laptop of the same type and I can assure you that this model supports the double delivery. You can add up to a stick more than 4 GB of ram to increase the memory capacity.

    ~ Mark

  • Qosmio F10 and dual channel

    Hello

    I have a Qosmio F10 with 512 MB, and I want to upgrade to 1024. I don't know if my qosmio supports Dual Channel. Can I add a sodimm pc2700 512 MB module and two-channel will work or I need exactly the same model of my laptop.

    TNX!
    Rood

    Hello

    Qosmio F10 uses DDR RAM modules. This modules support dual channel.
    As far as I know that you can upgrade the memory of max 2048MB and these modules are supported:
    PC2700 256 MB (PA3311U - 1 M 25)
    PC2700 512 MB (PA3312U - 1 M 51)
    1024MO PC2700 (PA3313U-1M1G)

  • 1x8GB or 2 x 4 GB? Single or dual channel memory sharp? for 6 Sleekbook

    Hello

    I want Sleekbook 6 1126ea.

    With A6 A6 - 4455M CPU and 4 GB RAM (single stick).

    I want to buy RAM from crucial.com (8 GB)

    I don't know if I should go to: 1x8GB (single stick) or 2 x 4 GB (double stick)

    Basically should go double or single channel RAM? o.O

    "Because I have heard that some programs might have problems with RAM dual channel." "And there is more chance for problems of" is it true?

    Help?

    The best configuration for bandwidth, memory and performance is the use of two memory modules.  One in each location. The modules must be identical in all respects. Buy only guarantee compatible memory modules.

    "Because I have heard that some programs might have problems with RAM dual channel." "And there is more chance for problems of" what you heard is not true. Just do a search online with unique compared to the memory dual channel mode channel as key wordsand you will see that what you were told is an invention.

    Best regards
    ERICO

  • Envy 17-j043cl: corrupted BIOS

    Problem started when my daughter has added a second HD and we have installed Linux on this drive. There is no entry for Linux BIOS boot change the default boot order, and all attempts to make changes only not good for the worst. We tried to go to the legacy mode, which promtped a reboot and the next screen to enter a code to take effect and a prompt for boot options, which never came to the top. When we went back into the BIOS, it shows the inheritance is always disabled. Enabling secure boot restarts even in a code to enter, but this also fails. Currently, we have tried to activate either (secure boot and legacy are disabled). Win 10 defective ACPI_BIOS_ERROR before secure boot disabled. We can enter the BIOS and go to Boot Options, navigate to the file boot firmly his Linux and efi. Linux works fine, we were not able to boot on a Windows 10 DVD to try to repair Windows 10 and at this point can't get secure startup, or legacy startup to activate. We also tried allowing only an administrator BIOS password but no change, still unable to activate.

    We tried F9 to restore the default BIOS, no change. We tried the menu to restore default BIOS, no change. We have tried, perhaps thinking that something has corrupted the BIOS, to level or to reflash the BIOS with BIOS version even. F.66 currently. His ID card system is 1965. The problem with all BIOS download for its Touchsmart from HP Envy 17-j043cl and unregistered is they don't have that file system board BIOS code 1966 1961, but hers is 1965. Without an exact match, we at our end to get this matter resolved. Any ideas? This sounds like a corrupted BIOS? Why does it seem impossible allow a secure start or inheritance? Is the boot options locked so as to only allow to boot Windows normally from the BIOS? Pointers or other ideas to help are appreciated.

    Joe

    Yes! It is fixed. Inside the interface EFI partition was the 01966.bin file, the last touch to this riddle. We were able to reflash it to the same version, F.66, USB, we had created since the softpaq (sp73289.exe), via the system, firmware management Diagnostics. It flashed fine and then started right Windows 10, so nothing on the disk hard Windows has been tampered. We'll put to start first at openSUSE 42.1 Leap and may start in Windows 10 in the Menu of Grub easier than playing with BIOS options each time.

    Thank you, DoughJohn, for all your help.

  • G7-1329wm Pavilion: 1329wm RAM Dual Channel. Update the bios?

    I bought 8 gigs of RAM laptop for my G7-1329wm Pavilion. Here it is:

    http://www.Amazon.com/GP/product/B00OUK919M?PSC=1&redirect=true&ref_=od_aui_detailpages00

    It is already much faster than what I had before. My problem is that I expected to run at a speed of 2133 MHz and dual channel mode. CPU - Z does not have these results.

    The two RAM slots show the same thing.

    It made me start to wonder. Maybe my cell phone does not support dual channel mode or these speeds. So I was wondering if I could do a BIOS update if everything goes well accept more modern equipment and their speed. I checked in CPU - Z that my bios is old path, return from 2012. I couldn't find any support for an update through HP. Can an HP expert please let me know what I can do to get the most out of my RAM speed?

    Repair:

    DDR3/1333 MHz (DDR3-1600 (1 GB / 2 GB / 4 GB / 8 GB) modules of memory supported as an alternative source for the DDR3-1333)

    So max the card/motherboard/BIOS processor speed will allow the memory runs is at 1333 mhz. I'm frankly surprised the memory you have installed works at all. It's the equivalent of putting gasoline in an engine that can be only ordinary.

    The problem goes well beyond BIOS. The chipset can operate at the maximum of 1600 mhz, and HP has set up to run at 1333.

    It is the specified memory:

    Memory modules (DDR3 10600 1333 MHz 2): 4 GB 621569-001

    http://www.Amazon.com/HP-621569-001-1333MHz-PC3-10600-SODIMM/DP/B005UF674S/ref=sr_1_1?ie=UTF8&QID=1457907477&SR=8-1&keywords=621569-001

    It may seem paradoxical, but your laptop can actually run a little faster and in double channel if you put in the slower memory. You can see there is a lot of information in gray in the CPU - Z I think because the system is not able to see all the technical features of memory, that she does not expect to be there.

  • [x 1 carbon] single channel or dual channel RAM?

    I am very curious how the built-in RAM x 1 carbon is arranged? Is channel single or double channel?

    Hello feyi1986,

    The carbon X 1 has built-in Dual Channel RAM.

    It is suddenly a diagram I have internal carbon 1 X.

    As you can see that it is Dual Channel.

    The on-board memory is DDR3L and dual channel at 1333 MHZ, of course you travel to the Intel Ivy Bridge on the carbon X 1.

    Hope this helps,

    Alex

    Note of the moderator; Edition at the request of post

  • RAM is the only way but is dual channel configuration.

    I have HP Pavilion a6000n, which has these capabilities of memory/features:

    • Dual channel memory architecture
    • Four connectors DIMM DDR2 240-pin
    • Supports the PC-6400 (800 MHz) DDR2 DIMM PC-4200 (533 MHz) and PC2-5300 (667 MHz)
    • Memory non - ECC, unbuffered
    • supports DIMM DDR2 2 GB modules
    • Supports up to 8 GB on 64-bit PCs
    • Supports up to 4 GB * on 32-bit PCs

    I recently upgraded from 2x512mb (1 GB) DDR2 PC-4200 to 2x2gb (4GB) DDR2 PC-6400 installed configuration dual channel (connectors DIMM 1 & 3). The BIOS and my CPU - Z application illustrates that the memory works as single Channel.

    This would indicate faulty RAM? Limitation of the motherboard? Any ideas? All inputs/advice is appreciated

    Thank you.

    Thank you very much! Problem solved.

  • HP Envy 4500: HP Envy 4500 printer and access Wifi University / iPhone Wifi Hotspot

    I have a HP Envy 4500 home and signed up for the moment of ink.  Works very well and I was hoping for a similar arrangement for my daughter who has just started at the University.  It seems that there are problems with the HP Envy 4500 connection to University share wireless networks.  I was wondering if the following scenario would work:

    1. his computer is connected to the printer via the USB port
    2. the printer is connected to a hotspot wifi on iPhone (his phone is already connected to wifi University)

    This work of the printer relay information support to HP for the purpose of instant ink?

    Thank you very much

    It worked so might be a good work around.

    Thank you

  • HP ENVY 750-177c: I have a HP ENVY 750-177c and has been upgraded and 2 thin black wires were disconnected.

    I have a HP ENVY 750-177c and has been upgraded and 2 thin black wires were disconnected from the motherboard.  They have loops at the end of the wires that look like they might slip on the pins.  The wires connect to the upper part of the box of the computer.  Where to reconnect?

    Find this card in your system. It is the M2 half-bridge Wireless card.  The other end of the wires must always be fixed.  There are 2 heels left and right of the '2 '.  If everything is correct, it is your physical WI - FI antenna. Just re - stick inside the case.  The small clips are used for an external aerial connection.

    PS<> have a good day...

  • Add internal Bluetooth and/or Wireless N dual channel HP dv4-2164us

    My computer is currently under warranty, so I'm not eager to open the machine until the computer comes out of the warranty.  Before opening the machine, so these are my questions:

    Quick questions for gurus.

    I think to add internal bluetooth and/or Wireless N dual channel my computer to HP dv4-2164us.

    1. My MB has connections to add a separate internal bluetooth card?
    2. To clarify the question 2... If the MB CAN normally do, HP is usually to have the connectors removed from the Mo for these types of potential improvements?
    3. What bluetooth card do you recommend?
    4. I currently have 2.4 GHz wireless n.  A different card support double n AND bluetooth would be a better solution?
    5. If Yes to question 4 What considerations such as antenna or other changes should be aware of them before the decision?
    6. All this that imagine you being to consider

    Thanks in advance!

    FYI, the Bluetooth does not have an antenna.

  • HP Envy 17-184na and Envy 17-141na

    I was comparing prices from different stores on a laptop computer called the

    HP Envy 17-j184na and found one called the HP Envy 17-j141na. Both laptops I found have model names different but seem exactly the same for me, so my question is:

    What is the difference between the Envy 17-j184na and 17-j141na?

    j 184na:

    http://WWW8.HP.com/h20195/v2/GetDocument.aspx?DocName=c04332225

    j 141na:

    http://support.HP.com/us-en/document/c04356668

    Only quickly obvious difference is the hard drive. The ordinary reader with 141 5400 RPM and 184 has a hybrid drive with a 8GB flash cache which should improve performance a bit.

  • HP envy 5530: hp envy 5530 administrator and password

    HP envy 5530 administrator and password

    Hello

    Please can someone help me.
    How to reset the password for administrators
    link below shows the web page out of Im lock.

    How to reset the password for administrators

    http://h30434.www3.HP.com/T5/image/serverpage/image-ID/123490i6312F91B84AC8FE7/image-size/original?v...

    Hi @leggoman,

    I am convinced that I will be able to help you find a solution, and I ask only that pay you it forward. When solve us the problem, I would mark you kindly post as accept as Solution so that others have the same or similar problem can find what worked for you.

    To reset the settings of the admin in the printers Web server shipped as shown in the screenshot you have validated, you need restore the network printer. Once restored, you must give the printer on the network.

    To restore the network settings, you will need to access the menu/wireless network on the front panel of the printer and look for the default network.

    Please do not forget to keep me informed of the result, so I can keep up with you. Thanks, I look forward to hear from you.

  • I have a computer laptop envy m7-k111dx and the hard drive has gone bad

    I have a computer laptop envy m7-k111dx and the hard drive went bad and want to order a HP recovery disc through the website to order it is to take me through circles

    Please use the support of HP recovery, you created earlier to return the computer to a factory State. If you create your HP recovery media when you first set up your computer, please contact the official support of HP in your region / country, via the HP portal to support all over the world, to see if the HP recovery support is available for your computer.

    If you have any other questions, feel free to ask.

    Please click the 'Thumbs Up' white LAURELS to show your appreciation

Maybe you are looking for

  • ADMINASTRATOR FORGOTTEN PASSWORD

    HOW DO YOU START YOUR SYSTEM VISTA IN SAFE MODE, THEN YOU CAN RESET THE PASSWORD? I'M a THE HP PAVILION s7700n WITH WINDOWS VISTA HOME PREMIUM.

  • Incompatible with Outlook 2000 and Windows 7!

    I just bought a new DELL PC with Windows 7.  I've been running with Office 2000 professional and XP Professional for many years.  When I installed Office 2000 on the new PC, I find that outlook 2000 does not work (unable to find the WAB. (DLL) After

  • Where else are the master does not understand?

    After launching a campaign, I have a handful of remaining in the stage of email recipients. Their status is: ' excluded e-mail: global exclusion. " But when I go to Configuration-> Exclude Master, I see nothing that would cause these individuals to e

  • Photoshop CS6 update is not possible

    I use Photoshop CS6, Version 13.0 x 64, extended. My system is Windows 7.When I try to update from the show, I get the error message that an update is not possible and that I should install Adobe Application Manager. When I try, I get the error messa

  • I am installation 5.1 SRM with EMC Recoverpoint

    Hi allI'm looking for more help on SRM 5.1 with recoverpoint instalation.I have instaled SRM 5.1 on two sites and two matching sites now. I'm confused about the Recoverpoint version works with MRS 5.1.Please post the link to download the version of E