Tunnel VPN and NAT
Hello. I'm creating a tunnel VPN IPSec LAN - to - LAN of my ASA5510 to another network but met an obstacle bit. My counterpart on the other side has informed me that he already has a VPN tunnel to another company that has the same IP range as my network(10.100.16.0 /24) and can not create the tunnel.
I was wondering is it possible to use NAT on the VPN tunnel so that traffic that goes from my network over the VPN tunnel gets translated and my counterpart on the other side sees this reflects the range of IP addresses?
Thanks in advance for any help.
Hello
Yes, you can use the same address you already use for internet access.
Just update your list of access crypto to reflect the new address and to ensure that the third party did the same.
Jon
Tags: Cisco Security
Similar Questions
-
client ipSec VPN and NAT on the router Cisco = FAIL
I have a Cisco 3825 router that I have set up for a Cisco VPN ipSec client. The same router is NAT.
ipSec logs, but can not reach the internal network unless NAT is disabled on the inside interface. But I need both at the same time.
Suggestions?
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group myclient
key password!
DNS 1.1.1.1
Domain name
pool myVPN
ACL 111
!
!
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
market arriere-route
!
!
list of card crypto clientmap client VPN - AAA authentication
card crypto clientmap AAA - VPN isakmp authorization list
client configuration address map clientmap crypto answer
10 ipsec-isakmp crypto map clientmap Dynamics dynmap
!interface Loopback0
IP 10.88.0.1 255.255.255.0
!
interface GigabitEthernet0/0
/ / DESC it's external interfaceIP 192.168.168.5 255.255.255.0
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
media type rj45
clientmap card crypto
!
interface GigabitEthernet0/1/ / DESC it comes from inside interface
10.0.1.10 IP address 255.255.255.0
IP nat inside<=================ipSec client="" connects,="" but="" cannot="" reach="" interior="" network="" unless="" this="" is="">=================ipSec>
IP virtual-reassembly
the route cache same-interface IP
automatic duplex
automatic speed
media type rj45!
IP local pool myVPN 10.88.0.2 10.88.0.10
p route 0.0.0.0 0.0.0.0 192.168.168.1
IP route 10.0.0.0 255.255.0.0 10.0.1.4
!IP nat inside source list 1 interface GigabitEthernet0/0 overload
!
access-list 1 permit 10.0.0.0 0.0.255.255
access-list 111 allow ip 10.0.0.0 0.0.255.255 10.88.0.0 0.0.0.255
access-list 111 allow ip 10.88.0.0 0.0.0.255 10.0.0.0 0.0.255.255Hello
I think that you need to configure the ACL default PAT so there first statemts 'decline' for traffic that is NOT supposed to be coordinated between the local network and VPN pool
For example, to do this kind of configuration, ACL and NAT
Note access-list 100 NAT0 customer VPN
access-list 100 deny ip 10.0.1.0 0.0.0.255 10.88.0.0 0.0.0.255
Note access-list 100 default PAT for Internet traffic
access-list 100 permit ip 10.0.1.0 0.0.0.255 ay
overload of IP nat inside source list 100 interface GigabitEthernet0/0
EDIT: seem to actually you could have more than 10 networks behind the routerThen you could modify the ACL on this
Note access-list 100 NAT0 customer VPN
access-list 100 deny ip 10.0.1.0 0.0.255.255 10.88.0.0 0.0.0.255
Note access-list 100 default PAT for Internet traffic
access-list 100 permit ip 10.0.1.0 0.0.255.255 ay
Don't forget to mark the answers correct/replys and/or useful answers to rate
-Jouni
-
Split of static traffic between the VPN and NAT
Hi all
We have a VPN from Site to Site that secures all traffic to and from 10.160.8.0/24 to/from 10.0.0.0/8. It's for everything - including Internet traffic. However, there is one exception (of course)...
The part that I can't make it work is if traffic comes from the VPN (10.0.0.0/8) of 10.160.8.5 (on 80 or 443), then the return traffic must go back through the VPN. BUT, if traffic 80 or 443 comes from anywhere else (Internet via X.X.X.X which translates to 10.160.8.5), so there need to be translated réécrirait Internet via Gig2.
I have the following Setup (tried to have just the neccessarry lines)...
interface GigabitEthernet2
address IP Y.Y.Y.Y 255.255.255.0! the X.X.X.X and Y.Y.Y.Y are in the same subnet
address IP X.X.X.X 255.255.255.0 secondary
NAT outside IP
card crypto ipsec-map-S2S
interface GigabitEthernet4.2020
Description 2020
encapsulation dot1Q 2020
IP 10.160.8.1 255.255.255.0
IP nat inside
IP virtual-reassembly
IP nat inside source list interface NAT-output GigabitEthernet2 overload
IP nat inside source static tcp 10.160.8.5 80 80 X.X.X.X map route No. - NAT extensible
IP nat inside source static tcp 10.160.8.5 443 443 X.X.X.X map route No. - NAT extensible
NAT-outgoing extended IP access list
refuse 10.160.8.5 tcp host 10.0.0.0 0.0.0.255 eq www
refuse 10.160.8.5 tcp host 10.0.0.0 0.0.0.255 eq 443
permit tcp host 10.160.8.5 all eq www
permit tcp host 10.160.8.5 any eq 443
No. - NAT extended IP access list
refuse 10.160.8.5 tcp host 10.0.0.0 0.0.0.255 eq www
refuse 10.160.8.5 tcp host 10.0.0.0 0.0.0.255 eq 443
allow an ip
route No. - NAT allowed 10 map
corresponds to the IP no. - NAT
With the above configuration, we can get to the Internet 10.160.8.5, but cannot cross it over the VPN tunnel (from 10.200.0.0/16). If I remove the two commands «ip nat inside source static...» ', then the opposite that happens - I can get then to 10.160.8.5 it VPN tunnel but I now can't get to it from the Internet.
How can I get both? It seems that when I hit the first NAT instruction (overload Gig2) that 'decline' in the list of ACL-NAT-outgoing punts me out of this statement of NAT. It can process the following statement of NAT (one of the 'ip nat inside source static... ") but does not seem to"deny"it in the NON - NAT ACL me punt out of this statement of NAT. That's my theory anyway (maybe something is happening?)
If this work like that or I understand something correctly? It's on a router Cisco's Cloud Services (CSR 1000v).
Thank you!
Your netmask is bad for your 10.0.0.0/8. I worry not about the port/protocol or since that can screw you up. A better way to do it would be to deny all IP vpn traffic.
NAT-outgoing extended IP access list
deny ip 10.160.8.0 0.0.0.0.255 10.0.0.0 0.255.255.255
...
No. - NAT extended IP access list
deny ip 10.160.8.0 0.0.0.0.255 10.0.0.0 0.255.255.255
allow an ip
Doc:
Router to router IPSec with NAT and Cisco Secure VPN Client overload
Thank you
Brendan
-
ASA5505 SSL AnyConnect VPN and NAT Reverse Path failure
I worked on it for a while and just have not found a solution yet.
I have a Cisco ASA5505 Setup at home and I try to use the AnyConnect VPN client to it. I followed the example of ASA 8.x split Tunnel but still miss me something.
My home network is 10.170.x.x and I install the VPN address to 10.170.13.x pool I have a Windows workstation running at 10.170.0.6, printers 10.170.0.20 and 21 and inside the router itself is 10.170.0.1
I can connect from the outside and am assigned an IP address of 10.170.13.10, but when I try to access network resources via ICMP or open a web page, the newspaper of the ASDM shows a bunch of this:
5. January 27, 2010 | 10: 33:37 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:36 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33: 35 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:34 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:30 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:29 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:28 | 305013 | 10.170.255.255 | 137. Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside:10.170.13.10/137 dst inside:10.170.255.255/137 refused due to path failure reverse that of NAT
5. January 27, 2010 | 10: 33:28 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:23 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:17 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10: 33: 13 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NAT
5. January 27, 2010 | 10:33:07 | 305013 | 10.170.0.6 | Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp src, dst outside: 10.170.13.10 inside: 10.170.0.6 (type 8, code 0) rejected due to the failure of reverse path of NATI tried several things with NAT, but were not able to go beyond that. Does anyone mind looking at my config running and help me with this? Thanks a bunch!
-Tim
Couple to check points.
name 10.17.13.0 UFP-VPN-pool looks like it should be the name 10.170.13.0 UFP-VPN-pool
inside_nat0_outbound to access extended list ip allow list zero 255.255.0.0 255.255.255.0 UFP-VPN-pool
Looks like that one
inside_nat0_outbound to list extended ip access list zero UFP-VPN-pool 255.255.255.0 255.255.255.0 allow
-
Remote access ASA, VPN and NAT
Hello
I try to get access to remote VPN work using a Cisco VPN client and ASA with no split tunneling. The VPN works a little, I can access devices inside when I connect, but I can't access the Internet. I don't see any errors in the log ASA except these:
1 Jul 04:59:15 % ASA-3-305006 gatekeeper: failed to create translation portmap for udp src outside:192.168.47.200/137 dst outside:192.168.47.255/137
1 Jul 04:59:15 % ASA-3-305006 gatekeeper: failed to create translation portmap for udp src outside:192.168.47.200/54918 dst outsidexx.xxx.xxx.xxx/53There is only one address public IP that is assigned to the external interface of DHCP. The Interior is 192.168.1.0/24 network which is PAT'ed to the external interface and the VPN network is 192.168.47.X.
I think my problem is that the net.47 is not NAT'ed out properly and I don't know how to put in place exactly. I can't understand how this is supposed to work since the net VPN technically provenance from the outside already.
Here are all the relevant config:
list of vpn access extended permits all ip 192.168.47.0 255.255.255.0
Within 1500 MTU
Outside 1500 MTU
IP local pool vpnpool 192.168.47.200 - 192.168.47.220 mask 255.255.255.0
IP verify reverse path to the outside interface
IP audit info alarm drop action
IP audit attack alarm drop action
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
Global interface (2 inside)
Global 1 interface (outside)
NAT (inside) 0-list of access vpn
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 2 192.168.47.0 255.255.255.0 outside
static (inside, outside) tcp 3074 XBOX360 3074 netmask 255.255.255.255 interface
static (inside, outside) udp 3074 XBOX360 3074 netmask 255.255.255.255 interface
public static (inside, outside) udp interface 88 88 XBOX360 netmask 255.255.255.255
public static tcp (indoor, outdoor) https someids netmask 255.255.255.255 https interfaceI can post more of the configuration if necessary.
Change ' nat (outside) 2 192.168.47.0 255.255.255.0 apart ' "NAT (2-list of vpn access outdoors outside)" gives these:
1 Jul 06:18:35 % gatekeeper ASA-3-305005: no group of translation not found for udp src outside:192.168.47.200/56003 dst outside:66.174.95.44/53
So, how I do right NAT VPN traffic so it can access the Internet?
A few things that needs to be changed:
(1) NAT exemption what ACL must be modified to be more specific while the traffic between the internal subnets and subnet pool vpn is not coordinated. NAT exemption takes precedence over all other statements of NAT, so your internet traffic from the vpn does not work.
This ACL:
list of vpn access extended permits all ip 192.168.47.0 255.255.255.0
Should be changed to:
extensive list of access vpn ip 192.168.47.0 255.255.255.0 allow
(2) you don't need statement "overall (inside) 2. Here's what to be configured:
no nat (outside) 2 192.168.47.0 255.255.255.0 outside
no global interface (2 inside)
NAT (outside) 1 192.168.47.0 255.255.255.0
(3) and finally, you must activate the following allow traffic back on the external interface:
permit same-security-traffic intra-interface
And don't forget to clear xlate after the changes described above and connect to your VPN.
Hope that helps.
-
Problem with the VPN and NAT configuration
Hi all
I have a VPN tunnel and NATing participates at the remote site.
I have the VPN tunnel from the absolutely perfect traffic from users, but I am struggling to manage the device via SNMP through the VPN tunnel.
Remote subnet is 192.168.10.0/24
That subnet gets PAT'd to 192.168.4.254/32
The subnet to HQ is 10.0.16.0/24
IP address of the ASA remote is 192.168.10.10
Of course, as this subnet is NAT would have I created a static NAT so that the 192.168.4.253 translates 192.168.10.10.
I can see that packets destined to the 192.168.4.253 device address comes to the end of the tunnel as long as the number of packets decrypted increases when you run a continuous ping to the device.
However, the unit will not return these packages. The wristwatch that 0 packets encrypted.
Please let me know if you need more information, or the output of the configuration complete.
When I start a capture on the ASA remote, I don't see ICMP packets to reach the ASA REAL ip (192.168.10.10). Maybe I set my NAT evil?
Also, there is no Interface inside, only an Interface outside. And the default route points to the next router ISP Hop on the external Interface.
Hope that all of the senses.
Thank you
Mario Rosa
No, unfortunately you can not NAT the ASA outside the IP of the interface itself.
-
Remote host IP SLA ping by tunnel VPN with NAT
Hi all
I did some research here, but don't drop on similar issues. I'm sure that what I want is not possible, but I want to make sure.
I want to monitor a remote host on the other side a VPN. The local endpoint is my ASA.
The local INSIDE_LAN traffic is NATted to 10.19.124.1 before entering the VPN tunnel.
Interesting VPN traffic used ACL card crypto:
access-list 1 permit line ACL_TUNNELED_TO_REMOTE extended ip host 10.19.124.1 192.168.1.0 255.255.255.0
NAT rules:
Global (OUTSIDE) 2 10.19.124.1 mask 255.255.255.255 subnet
NAT (INSIDE_LAN) 2-list of access ACL_NAT_TO_REMOTE
NAT ACL
access-list 1 permit line ACL_NAT_TO_REMOTE extended ip 172.19.126.32 255.255.255.224 192.168.1.0 255.255.255.0
This configuration works very well for traffic from hosts in 172.19.126.32 255.255.255.224 is 192.168.1.0 255.255.255.0.
However, I like to use "ip sla" on the SAA itself to monitor a remote host with icmp ping 192.168.1.0. This would imply NATting one IP on the ASA to 10.19.124.1, but I do not see how to do this. None of the interfaces on the SAA are logical, to use as a source for this interface.
Thanks for ideas and comments.
Concerning
You are absolutely right, that unfortunately you won't able to NAT interface ASA IP address. NAT works for traffic passing by the ASA, don't not came from the SAA itself.
-
Having a few problems and looking for suggestions. Working document (http://www.cisco.com/en/US/docs/security/asa/asa91/configuration/firewall/asa_91_firewall_cli.pdf) on Pages 3-24 and 3-25. In my lab configuration everything works except for be able to ping the management vpn for network bethind the second ASA.
I exceeded the configs and checked vs examples, but of course miss me something.
In the ASA2 VPN client.
My configs are attached with a few parts cleaned.
An ICMP trace says:
Outside ICMP echo request: 10.10.120.1 outside: 192.168.16.50 ID = seq 2 = 12582 len = 32
Run a trace of the package (entry packet - map out icmp 10.10.120.1 0 192.168.15.50 0) shows:
Phase: 1
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 0.0.0.0 0.0.0.0 outdoors
Phase: 2
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group OUTSIDE_IN in interface outside
OUTSIDE_IN list extended access permit icmp any one
Additional information:
Phase: 3
Type: NAT
Subtype:
Result: ALLOW
Config:
network retail_vpn object
dynamic NAT interface (outdoors, outdoor)
Additional information:
Phase: 4
Type: NAT
Subtype: volatile
Result: ALLOW
Config:
Additional information:
Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Result:
input interface: outdoors
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: drop
Drop-reason: unable to NAT (nat-xlate-failure)
Something is either not properly natted or the way back is a problem, but I can't put my finger on it.
Anyone with suggestions
Thank you
Jerry
Hello
I guess there a typing error in the destination IP address "packet - trace" because I can't find a reference to this subnet/IP configuration.
You can try the "package Tracker" in a slightly different format
entry Packet-trace out icmp 10.10.120.1 8 192.168.16.50 0
The difference are the Type and Code numbers after the source IP address. Now, it simulates an echo ICMP message. The previous format of the order could have caused the failure NAT result.
I guess you try to convey the L2L VPN connection traffic.
Then you are already seem to have the right configuration of NAT. But it seems to me that you are missing also those source/destination configuration VPN L2L network.
permit access list extended ip object retail_vpn object riverroad_inside vpn_inside
Even on the ASA1
permit access list extended ip object riverroad_inside object retail_vpn vpn_inside
Can check you the above things and let me know if those who helped with the situation.
-Jouni
-
We have a place where you want to set up a tunnel VPN to our headquarters.
In this place, there is a router that PAT (NAT overloading), and then a few jumps more, there is a firewall that makes the NAT.
Is this could pose a problem for the VPN tunnel?
Here's a "pattern" of what looks like the connection.
Customer--> PAT - router-->--> Internet--> CVPN3005 NAT firewall
I hope you can provide me with an answer.
VPN tunnel will not work in your scenario. NAT second change address and the ports you want to use for the vpn tunnel. So the port 500 wil be translated to top port and will be rejected at HQ.
-
HTTPS protocol between the client vpn and host of the internet through tunnel ipsec-parody
Hello
We have a cisco ASA 5505 and try to get the next job:
ip (192.168.75.5) - connected to the Cisco ASA 5505 VPN client
the customer gets a specific route for an internet address (79.143.218.35 255.255.255.255 192.168.75.1 192.168.75.5 100)
When I try to access the url of the client, I get a syn sent with netstat
When I try trace ASA package, I see the following:
1 FLOW-SEARCH ALLOW Not found no corresponding stream, creating a new stream
2 ROUTE SEARCH entry ALLOW in 0.0.0.0 0.0.0.0 outdoors
3 ACCESS-LIST Journal ALLOW Access-group outside_access_in in interface outside
outside_access_in list extended access permitted tcp everything any https eq
access-list outside_access_in note hyperion outside inside
4 IP-OPTIONS ALLOW 5 CP-PUNT ALLOW 6 VPN IPSec-tunnel-flow ALLOW 7 IP-OPTIONS ALLOW 8 VPN encrypt ALLOW outdoors upward upward outdoors upward upward drop (ipsec-parody) Parody of detected IPSEC When I try the reverse (i.e. from the internet host to vpn client), it seems to work:
1 FLOW-SEARCH ALLOW Not found no corresponding stream, creating a new stream
2 ROUTE SEARCH entry ALLOW in 192.168.75.5 255.255.255.255 outside
3 ACCESS-LIST Journal ALLOW Access-group outside_access_in in interface outside
outside_access_in of access allowed any ip an extended list
4 IP-OPTIONS ALLOW 5 VPN IPSec-tunnel-flow ALLOW 6 VPN encrypt ALLOW My question is why this phenomenon happens and how solve us this problem?
Thanks in advance, Sipke
our running-config:
: Saved
:
ASA Version 8.0 (4)
!
ciscoasa hostname
domain somedomain
activate the password - encrypted
passwd - encrypted
names of
name 10.10.1.0 Hyperion
name 164.140.159.x xxxx
name 192.168.72.25 xxxx
name 192.168.72.24 xxxx
name 192.168.72.196 xxxx
name 192.168.75.0 vpn clients
name 213.206.236.0 xxxx
name 143.47.160.0 xxxx
name 141.143.32.0 xxxx
name 141.143.0.0 xxxx
name 192.168.72.27 xxxx
name 10.1.11.0 xxxx
name 10.1.2.240 xxxx
name 10.1.1.0 xxxx
name 10.75.2.1 xxxx
name 10.75.2.23 xxxx
name 192.168.72.150 xxxx
name 192.168.33.0 xxxx
name 192.168.72.26 xxxx
name 192.168.72.5 xxxx
name 192.168.23.0 xxxx
name 192.168.34.0 xxxx
name 79.143.218.35 inethost
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.72.254 255.255.255.0
OSPF cost 10
!
interface Vlan2
nameif outside
security-level 0
IP address 193.173.x.x 255.255.255.240
OSPF cost 10
!
interface Vlan3
Shutdown
nameif dmz
security-level 50
192.168.50.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan23
nameif wireless
security-level 80
192.168.40.1 IP address 255.255.255.0
OSPF cost 10
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 3
!
interface Ethernet0/6
switchport access vlan 23
!
interface Ethernet0/7
!
passive FTP mode
clock timezone THATS 1
clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00
DNS lookup field inside
DNS server-group DefaultDNS
domain pearle.local
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service RDP - tcp
Remote Desktop Protocol Description
EQ port 3389 object
object-group service UDP - udp VC
range of object-port 60000 60039
object-group VC - TCP tcp service
60000 60009 object-port Beach
object-group service tcp Fortis
1501 1501 object-port Beach
Beach of port-object 1502-1502
Beach of port-object sqlnet sqlnet
1584 1584 object-port Beach
1592 1592 object-port Beach
object-group service tcp fortis
1592 1592 object-port Beach
Beach of port-object 1502-1502
1584 1584 object-port Beach
Beach of port-object sqlnet sqlnet
1501 1501 object-port Beach
1500 1500 object-port Beach
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.50.0 255.255.255.0
object-network 192.168.72.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-network VPN_Pool_2 255.255.255.0
the DM_INLINE_NETWORK_2 object-group network
object-network 192.168.50.0 255.255.255.0
object-network 192.168.72.0 255.255.255.0
object-group network inside-networks
object-network 192.168.72.0 255.255.255.0
WingFTP_TCP tcp service object-group
Secure FTP description
port-object eq 989
port-object eq 990
DM_INLINE_TCP_1 tcp service object-group
port-object eq ftp
port-object eq ftp - data
Group object WingFTP_TCP
DM_INLINE_TCP_2 tcp service object-group
port-object eq ftp
port-object eq ftp - data
Group object WingFTP_TCP
the DM_INLINE_NETWORK_3 object-group network
object-network 192.168.72.0 255.255.255.0
object-network VPN_Pool_2 255.255.255.0
the DM_INLINE_NETWORK_4 object-group network
object-network 192.168.72.0 255.255.255.0
object-network VPN_Pool_2 255.255.255.0
object-group network Oracle
network-object OracleTwo 255.255.224.0
network-object OracleOne 255.255.240.0
network-object OracleThree 255.255.224.0
the DM_INLINE_NETWORK_5 object-group network
network-object Grandvision 255.255.255.0
network-object Grandvision2 255.255.255.240
object-network Grandvision3 255.255.255.0
host of the object-Network Grandvision4
host of the object-Network GrandVision_PC
the DM_INLINE_NETWORK_6 object-group network
network-object Grandvision 255.255.255.0
network-object Grandvision2 255.255.255.240
object-network Grandvision3 255.255.255.0
host of the object-Network Grandvision4
host of the object-Network GrandVision_PC
the DM_INLINE_NETWORK_7 object-group network
network-object Grandvision 255.255.255.0
network-object Grandvision2 255.255.255.240
object-network Grandvision3 255.255.255.0
host of the object-Network GrandVision_PC
the DM_INLINE_NETWORK_8 object-group network
network-object Grandvision 255.255.255.0
network-object Grandvision2 255.255.255.240
object-network Grandvision3 255.255.255.0
host of the object-Network GrandVision_PC
object-group service DM_INLINE_SERVICE_2
the purpose of the ip service
EQ-3389 tcp service object
the DM_INLINE_NETWORK_9 object-group network
network-object OracleThree 255.255.0.0
network-object OracleTwo 255.255.224.0
network-object OracleOne 255.255.240.0
object-group service DM_INLINE_SERVICE_3
the purpose of the ip service
EQ-3389 tcp service object
Atera tcp service object-group
Atera Webbased monitoring description
8001 8001 object-port Beach
8002 8002 object-port Beach
8003 8003 object-port Beach
WingFTP_UDP udp service object-group
port-object eq 989
port-object eq 990
WingFTP tcp service object-group
Description range of ports for the transmission of data
object-port range 1024-1054
HTTPS_redirected tcp service object-group
Description redirect WingFTP Server
port-object eq 40200
Note to inside_access_in to access list ICMP test protocol inside outside
inside_access_in list extended access allow icmp 192.168.72.0 255.255.255.0 any
Note to inside_access_in to access list ICMP test protocol inside outside
access-list inside_access_in note HTTP inside outside
inside_access_in list extended access allowed object-group TCPUDP 192.168.72.0 255.255.255.0 any eq www
access-list inside_access_in note queries DNS inside to outside
inside_access_in list extended access allowed object-group TCPUDP 192.168.72.0 255.255.255.0 no matter what eq field
access-list inside_access_in note the HTTPS protocol inside and outside
inside_access_in list extended access permitted tcp 192.168.72.0 255.255.255.0 any https eq
Note to inside_access_in to access list ICMP test protocol inside outside
access-list inside_access_in note 7472 Epo-items inside outside
inside_access_in list extended access permitted tcp 192.168.72.0 255.255.255.0 any eq 7472
access-list inside_access_in note POP3 inside outside
inside_access_in list extended access permitted tcp 192.168.72.0 255.255.255.0 any eq pop3
inside_access_in list extended access permit udp host LifeSize-PE-HQ any object-group UDP - VC
inside_access_in list extended access permit tcp host LifeSize-PE-HQ all eq h323
access-list inside_access_in note video conference services
inside_access_in list extended access permit tcp host LifeSize-PE-HQ any object-group VC - TCP
inside_access_in list extended access permitted tcp 192.168.72.0 255.255.255.0 any
Note to inside_access_in to access list Fortis
inside_access_in list extended access permitted tcp 192.168.72.0 255.255.255.0 any object-group Fortis
access extensive list ip 192.168.40.0 inside_access_in allow 255.255.255.0 any
inside_access_in list extended access permitted tcp 192.168.40.0 255.255.255.0 any
inside_access_in list extended access permitted tcp 192.168.40.0 255.255.255.0 any eq www
inside_access_in list extended access permitted tcp 192.168.40.0 255.255.255.0 any https eq
inside_access_in allowed all Hyperion 255.255.255.0 ip extended access list
inside_access_in list extended access udp allowed any any eq isakmp
inside_access_in list extended access udp allowed any any eq ntp
inside_access_in list extended access udp allowed any any eq 4500
inside_access_in list of allowed ip extended access any Oracle object-group
inside_access_in list extended access udp allowed any any eq 10000
access-list inside_access_in note PPTP inside outside
inside_access_in list extended access permit tcp any any eq pptp
access-list inside_access_in note WILL inside outside
inside_access_in list extended access will permit a full
Note to inside_access_in to access the Infrastructure of the RIM BES server list
inside_access_in list extended access permit tcp host BESServer any eq 3101
inside_access_in list extended access permit tcp any any DM_INLINE_TCP_2 object-group
inside_access_in list extended access permit tcp any any HTTPS_redirected object-group
access extensive list ip Hyperion 255.255.255.0 inside_access_in 255.255.255.0 allow VPN_Pool_2
inside_access_in list extended access permit udp any host 86.109.255.177 eq 1194
access extensive list ip 192.168.72.0 inside_access_in allow 255.255.255.0 DM_INLINE_NETWORK_7 object-group
access extensive list ip VPN_Pool_2 inside_access_in allow 255.255.255.0 any
inside_access_in list extended access deny ip any any inactive debug log
Note to outside_access_in to access list ICMP test protocol outside inside
outside_access_in list extended access permit icmp any one
access-list outside_access_in Note SMTP outside inside
outside_access_in list extended access permit tcp any any eq smtp
outside_access_in list extended access udp allowed any any eq ntp disable journal
access-list outside_access_in note 7472 EPO-items outside inside
outside_access_in list extended access permit tcp any any eq 7472
outside_access_in list extended access permit tcp any any object-group inactive RDP
outside_access_in list extended access permit tcp any any eq www
outside_access_in list extended access permit tcp any any HTTPS_redirected object-group
outside_access_in list extended access permitted tcp everything any https eq
access-list outside_access_in note hyperion outside inside
outside_access_in list extended access permitted tcp Hyperion 255.255.255.0 DM_INLINE_NETWORK_4 object-group
outside_access_in to access Hyperion 255.255.255.0 ip extended list object-group DM_INLINE_NETWORK_3 allow
outside_access_in list extended access permit tcp any host LifeSize-PE-HQ eq h323
outside_access_in list extended access permit tcp any host LifeSize-PE-HQ object-group VC - TCP
outside_access_in list extended access permit udp any host group-object-LifeSize-PE-HQ UDP - VC
outside_access_in of access allowed any ip an extended list
outside_access_in list extended access udp allowed any any eq 4500
outside_access_in list extended access udp allowed any any eq isakmp
outside_access_in list extended access udp allowed any any eq 10000
outside_access_in list extended access will permit a full
outside_access_in list extended access permit tcp any any eq pptp
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
outside_access_in list extended access allowed object-group ip DM_INLINE_NETWORK_8 192.168.72.0 255.255.255.0 inactive
outside_access_in list extended access permit tcp any any Atera object-group
outside_access_in list extended access deny ip any any inactive debug log
outside_1_cryptomap list extended access allowed object-group Hyperion DM_INLINE_NETWORK_2 255.255.255.0 ip
outside_1_cryptomap to access extended list ip 192.168.50.0 allow Hyperion 255.255.255.0 255.255.255.0
access extensive list ip 192.168.72.0 inside_nat0_outbound allow Hyperion 255.255.255.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 193.172.182.64 255.255.255.240
inside_nat0_outbound list of allowed ip extended access all 192.168.72.192 255.255.255.192
inside_nat0_outbound list of allowed ip extended access all 192.168.72.0 255.255.255.0
access extensive list ip 192.168.72.0 inside_nat0_outbound allow 255.255.255.0 VPN_Pool_2 255.255.255.0
access extensive list ip 192.168.72.0 inside_nat0_outbound allow 255.255.255.0 DM_INLINE_NETWORK_5 object-group
inside_nat0_outbound list of allowed ip extended access all GrandVisionSoesterberg 255.255.255.0
inside_nat0_outbound list of allowed ip extended access any Swabach 255.255.255.0
access-list 200 scope allow tcp all fortis of fortis host object-group
access extensive list ip VPN_Pool_2 outside_nat0_outbound allow 255.255.255.0 DM_INLINE_NETWORK_9 object-group
outside_cryptomap_2 list extended access allowed object-group Hyperion DM_INLINE_NETWORK_1 255.255.255.0 ip
outside_cryptomap_2 to access extended list ip 192.168.50.0 allow Hyperion 255.255.255.0 255.255.255.0
Note Wireless_access_in of access list, select Hyperion / wifi access NAT rule.
Access extensive list ip 192.168.40.0 Wireless_access_in allow Hyperion inactive 255.255.255.0 255.255.255.0
Wireless_access_in list extended access deny ip 192.168.40.0 255.255.255.0 192.168.72.0 255.255.255.0
Comment by Wireless_access_in-list of the traffic Internet access
Access extensive list ip 192.168.40.0 Wireless_access_in allow 255.255.255.0 any
standard access list splittunnelclientvpn allow 192.168.72.0 255.255.255.0
splittunnelclientvpn list standard access allowed Hyperion 255.255.255.0
standard access list splittunnelclientvpn allow Pearleshare 255.255.255.0
splittunnelclientvpn list standard access allowed host 85.17.235.22
splittunnelclientvpn list standard access allowed OracleThree 255.255.224.0
standard access list splittunnelclientvpn allow 143.47.128.0 255.255.240.0
splittunnelclientvpn list standard access allowed host inethost
Standard access list SplittnlHyperion allow OracleThree 255.255.0.0
Standard access list SplittnlOOD allow OracleThree 255.255.0.0
Standard access list SplittnlOOD allow 143.47.128.0 255.255.240.0
access extensive list ip 192.168.72.0 outside_cryptomap allow 255.255.255.0 DM_INLINE_NETWORK_6 object-group
outside_cryptomap_1 list of allowed ip extended access all GrandVisionSoesterberg 255.255.255.0
outside_cryptomap_3 list of allowed ip extended access any Swabach 255.255.255.0
192.168.72.0 IP Access-list extended sheep 255.255.255.0 GrandVisionSoesterberg 255.255.255.0 allow
192.168.72.0 IP Access-list extended sheep 255.255.255.0 VPN_Pool_2 255.255.255.0 allow
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
MTU 1500 wireless
local pool VPN_DHCP 192.168.72.220 - 192.168.72.235 255.255.255.0 IP mask
mask 192.168.75.1 - 192.168.75.50 255.255.255.0 IP local pool VPN_Range_2
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 613.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (wireless) 1 192.168.40.0 255.255.255.0
public static tcp (indoor, outdoor) interface smtp smtp Mailsrv_Pearle_Europe netmask 255.255.255.255
public static tcp (indoor, outdoor) interface ftp ftp netmask 255.255.255.255 Pearle-DC02
public static 990 Pearle-DC02 990 netmask 255.255.255.255 interface tcp (indoor, outdoor)
static (inside, outside) tcp 3389 3389 Mailsrv_Pearle_Europe netmask 255.255.255.255 interface
public static tcp (indoor, outdoor) interface www Pearle-DC02 www netmask 255.255.255.255
public static 40200 Pearle-DC02 40200 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static tcp (indoor, outdoor) interface https Exchange2010 https netmask 255.255.255.255
public static tcp (indoor, outdoor) interface h323 h323 LifeSize-PE-HQ netmask 255.255.255.255
public static 60000 60000 LifeSize-PE-HQ netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60001 LifeSize-PE-HQ 60001 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60002 LifeSize-PE-HQ 60002 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60003 LifeSize-PE-HQ 60003 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60004 LifeSize-PE-HQ 60004 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60005 LifeSize-PE-HQ 60005 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60006 LifeSize-PE-HQ 60006 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60007 LifeSize-PE-HQ 60007 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60008 LifeSize-PE-HQ 60008 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static 60009 LifeSize-PE-HQ 60009 netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static (inside, outside) udp interface 60001 LifeSize-PE-HQ 60001 netmask 255.255.255.255
public static (inside, outside) udp interface 60002 LifeSize-PE-HQ 60002 netmask 255.255.255.255
public static (inside, outside) udp interface 60003 LifeSize-PE-HQ 60003 netmask 255.255.255.255
public static (inside, outside) udp interface 60004 LifeSize-PE-HQ 60004 netmask 255.255.255.255
public static (inside, outside) udp interface 60005 LifeSize-PE-HQ 60005 netmask 255.255.255.255
public static (inside, outside) udp interface 60006 LifeSize-PE-HQ 60006 netmask 255.255.255.255
public static (inside, outside) udp interface 60007 LifeSize-PE-HQ 60007 netmask 255.255.255.255
public static (inside, outside) udp interface 60008 LifeSize-PE-HQ 60008 netmask 255.255.255.255
public static (inside, outside) udp interface 60009 LifeSize-PE-HQ 60009 netmask 255.255.255.255
public static (inside, outside) udp interface 60010 LifeSize-PE-HQ 60010 netmask 255.255.255.255
public static (inside, outside) udp interface 60011 LifeSize-PE-HQ 60011 netmask 255.255.255.255
public static (inside, outside) udp interface 60012 LifeSize-PE-HQ 60012 netmask 255.255.255.255
public static (inside, outside) udp interface 60013 LifeSize-PE-HQ 60013 netmask 255.255.255.255
public static (inside, outside) udp interface 60014 LifeSize-PE-HQ 60014 netmask 255.255.255.255
public static (inside, outside) udp interface 60015 LifeSize-PE-HQ 60015 netmask 255.255.255.255
public static (inside, outside) udp interface 60016 LifeSize-PE-HQ 60016 netmask 255.255.255.255
public static (inside, outside) udp interface 60017 LifeSize-PE-HQ 60017 netmask 255.255.255.255
public static (inside, outside) udp interface 60018 LifeSize-PE-HQ 60018 netmask 255.255.255.255
public static (inside, outside) udp interface 60019 LifeSize-PE-HQ 60019 netmask 255.255.255.255
public static (inside, outside) udp interface 60020 LifeSize-PE-HQ 60020 netmask 255.255.255.255
public static (inside, outside) udp interface 60021 60021 LifeSize-PE-HQ netmask 255.255.255.255
public static (inside, outside) udp interface 60022 LifeSize-PE-HQ 60022 netmask 255.255.255.255
public static (inside, outside) udp interface 60023 LifeSize-PE-HQ 60023 netmask 255.255.255.255
public static (inside, outside) udp interface 60024 LifeSize-PE-HQ 60024 netmask 255.255.255.255
public static (inside, outside) udp interface 60025 LifeSize-PE-HQ 60025 netmask 255.255.255.255
public static (inside, outside) udp interface 60026 LifeSize-PE-HQ 60026 netmask 255.255.255.255
public static (inside, outside) udp interface 60027 LifeSize-PE-HQ 60027 netmask 255.255.255.255
public static (inside, outside) udp interface 60028 LifeSize-PE-HQ 60028 netmask 255.255.255.255
public static (inside, outside) udp interface 60029 LifeSize-PE-HQ 60029 netmask 255.255.255.255
public static (inside, outside) udp interface 60030 LifeSize-PE-HQ 60030 netmask 255.255.255.255
public static (inside, outside) udp interface 60031 LifeSize-PE-HQ 60031 netmask 255.255.255.255
public static (inside, outside) udp interface 60032 LifeSize-PE-HQ 60032 netmask 255.255.255.255
public static (inside, outside) udp interface 60033 LifeSize-PE-HQ 60033 netmask 255.255.255.255
public static (inside, outside) udp interface 60034 LifeSize-PE-HQ 60034 netmask 255.255.255.255
public static (inside, outside) udp interface 60035 LifeSize-PE-HQ 60035 netmask 255.255.255.255
public static (inside, outside) udp interface 60036 LifeSize-PE-HQ 60036 netmask 255.255.255.255
public static (inside, outside) udp interface 60037 LifeSize-PE-HQ 60037 netmask 255.255.255.255
public static (inside, outside) udp interface 60038 LifeSize-PE-HQ 60038 netmask 255.255.255.255
public static (inside, outside) udp interface 60039 LifeSize-PE-HQ 60039 netmask 255.255.255.255
public static (inside, outside) udp interface 60040 60040 LifeSize-PE-HQ netmask 255.255.255.255
public static Mailsrv_Pearle_Europe 7472 netmask 255.255.255.255 7472 interface tcp (indoor, outdoor)
public static LanSweep-XP netmask 255.255.255.255 8001 8001 interface tcp (indoor, outdoor)
public static 8002 8002 LanSweep-XP netmask 255.255.255.255 interface tcp (indoor, outdoor)
public static LanSweep-XP netmask 255.255.255.255 8003 8003 interface tcp (indoor, outdoor)
static (inside, outside) 193.173.12.194 tcp https Pearle-DC02 https netmask 255.255.255.255
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Access-group Wireless_access_in in wireless interface
Route outside 0.0.0.0 0.0.0.0 193.173.12.206 1
Route outside OracleThree 255.255.224.0 193.173.12.198 1
Route outside 143.47.128.0 255.255.240.0 193.173.12.198 1
Route inside 172.27.0.0 255.255.255.0 Pearle-DC02 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication LOCAL telnet console
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.40.0 255.255.255.0 Wireless
http 192.168.1.0 255.255.255.0 inside
http 192.168.72.0 255.255.255.0 inside
http GrandVisionSoesterberg 255.255.255.0 inside
SNMP-server host inside 192.168.33.29 survey community public version 2 c
location of Server SNMP Schiphol
contact Server SNMP SSmeekes
SNMP-Server Public community
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set esp-aes-256 GRANDVISION esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define security association lifetime 28800 seconds
cryptographic kilobytes 4608000 life of the set - the association of security of the 65535 SYSTEM_DEFAULT_CRYPTO_MAP of the dynamic-map
card crypto outside_map0 1 match address outside_cryptomap_1
outside_map0 card crypto 1jeu pfs
outside_map0 card crypto 1jeu peer 212.78.223.182
outside_map0 card crypto 1jeu transform-set ESP ESP-3DES-SHA-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-ESP ESP-3DES-MD5 MD5-DES-SHA ESP-DES-MD5
outside_map0 map 1 lifetime of security association set seconds 28800 crypto
card crypto outside_map0 1 set security-association life kilobytes 4608000
card crypto game 2 outside_map0 address outside_cryptomap_2
outside_map0 crypto map peer set 2 193.173.12.193
card crypto outside_map0 2 game of transformation-ESP ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5-DES-SHA ESP-DES-MD5
life card crypto outside_map0 2 set security-association seconds 28800
card crypto outside_map0 2 set security-association life kilobytes 4608000
card crypto outside_map0 3 match address outside_1_cryptomap
outside_map0 card crypto 3 set pfs
outside_map0 card crypto 3 peers set 193.172.182.66
outside_map0 crypto map 3 the value transform-set ESP-3DES-SHA
life card crypto outside_map0 3 set security-association seconds 28800
card crypto outside_map0 3 set security-association life kilobytes 4608000
card crypto outside_map0 game 4 address outside_cryptomap
outside_map0 card crypto 4 peers set 213.56.81.58
outside_map0 4 set transform-set GRANDVISION crypto card
life card crypto outside_map0 4 set security-association seconds 28800
card crypto outside_map0 4 set security-association life kilobytes 4608000
card crypto outside_map0 5 match address outside_cryptomap_3
outside_map0 card crypto 5 set pfs
outside_map0 crypto card 5 peers set 86.109.255.177
outside_map0 card crypto 5 game of transformation-ESP ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5-DES-SHA ESP-DES-MD5
life card crypto outside_map0 5 set security-association seconds 28800
card crypto outside_map0 5 set security-association life kilobytes 4608000
Crypto map outside_map0 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
outside_map0 interface card crypto outside
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP enable dmz
crypto ISAKMP enable wireless
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.168.72.0 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.72.0 255.255.255.0 inside
SSH GrandVisionSoesterberg 255.255.255.0 inside
SSH 213.144.239.0 255.255.255.192 outside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd dns 194.151.228.18 is 10.10.1.100
dhcpd outside auto_config
!
dhcpd address 192.168.72.253 - 192.168.72.253 inside
!
dhcpd address dmz 192.168.50.10 - 192.168.50.50
dhcpd enable dmz
!
dhcpd address wireless 192.168.40.10 - 192.168.40.99
dhcpd dns 194.151.228.18 wireless interface
dhcpd activate wireless
!
a basic threat threat detection
host of statistical threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Group Policy "pearle_vpn_Hyp only" internal
attributes of Group Policy "pearle_vpn_Hyp only".
value of server WINS 192.168.72.25
value of server DNS 192.168.72.25
Protocol-tunnel-VPN IPSec l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list SplittnlHyperion
Split-dns value pearle.local
internal pearle_vpn_OOD_only group policy
attributes of the strategy of group pearle_vpn_OOD_only
value of Split-tunnel-network-list SplittnlOOD
internal pearle_vpn group policy
attributes of the strategy of group pearle_vpn
value of server WINS 192.168.72.25
value of server DNS 192.168.72.25
Protocol-tunnel-VPN IPSec l2tp ipsec svc
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list splittunnelclientvpn
Pearle.local value by default-field
Split-dns value pearle.local
username anyone password encrypted password
username something conferred
VPN-group-policy pearle_vpn_OOD_only
type of remote access service
tunnel-group 193 type ipsec-l2l
tunnel-group 193 ipsec-attributes
pre-shared-key *.
tunnel-group 193.173.12.193 type ipsec-l2l
IPSec-attributes tunnel-group 193.173.12.193
pre-shared-key *.
NOCHECK Peer-id-validate
type tunnel-group pearle_vpn remote access
tunnel-group pearle_vpn General-attributes
address pool VPN_Range_2
Group Policy - by default-pearle_vpn
pearle_vpn group of tunnel ipsec-attributes
pre-shared-key *.
type tunnel-group Pearle_VPN_2 remote access
attributes global-tunnel-group Pearle_VPN_2
address pool VPN_Range_2
strategy-group-by default "pearle_vpn_Hyp only".
IPSec-attributes tunnel-group Pearle_VPN_2
pre-shared-key *.
tunnel-group 213.56.81.58 type ipsec-l2l
IPSec-attributes tunnel-group 213.56.81.58
pre-shared-key *.
tunnel-group 212.78.223.182 type ipsec-l2l
IPSec-attributes tunnel-group 212.78.223.182
pre-shared-key *.
tunnel-group 86.109.255.177 type ipsec-l2l
IPSec-attributes tunnel-group 86.109.255.177
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the pptp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:7d4d9c7ca7c865d9e40f5d77ed1238eb
: end
ASDM image disk0: / asdm - 613.bin
ASDM BESServer 255.255.255.255 inside location
ASDM VPN_Pool_2 255.255.255.0 inside location
ASDM OracleTwo 255.255.224.0 inside location
ASDM OracleOne 255.255.240.0 inside location
ASDM OracleThree 255.255.224.0 inside location
ASDM location Exchange2010 255.255.255.255 inside
ASDM location Grandvision 255.255.255.0 inside
ASDM Grandvision2 255.255.255.240 inside location
ASDM Grandvision3 255.255.255.0 inside location
ASDM Grandvision4 255.255.255.255 inside location
ASDM GrandVision_PC 255.255.255.255 inside location
ASDM location LanSweep-XP 255.255.255.255 inside
ASDM GrandVisionSoesterberg 255.255.255.0 inside location
ASDM location Pearle-DC02 255.255.255.255 inside
ASDM location Pearle-WDS 255.255.255.255 inside
ASDM location Swabach 255.255.255.0 inside
ASDM GrandVisionSoesterberg2 255.255.255.0 inside location
don't allow no asdm history
Where is that host (inethost)? Inside of the ASA, or on the internet (on the outside)?
If it is outside, you must configure the NAT for the pool of vpn as you turn on the SAA.
NAT (outside) 1 192.168.75.0 255.255.255.0
-
Problems with basic setup and split tunneling VPN
I created a SSL VPN in an ASA CISCO ASDM 6.6 8.6 running.
IM able to connect to the VPN and reach all the devices with the LAN but I am not able to browse the web. When I activate the tunnel split Im able to browse the web, but then Im not able to reach any internal device.
Here is part of the show's run:network of the RedInterna object
150.211.101.0 subnet 255.255.255.0
Description Red Interna
network of the NETWORK_OBJ_10.4.1.0_28 object
subnet 10.4.1.0 255.255.255.240
inside_access_in list extended access permitted ip object RedInterna all
Standard access list VPN_INTERNET allow 150.211.101.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
local pool VPN_POOL 10.4.1.1 - 10.4.1.14 255.255.255.240 IP mask
failover
secondary failover lan unit
failover lan interface GigabitEthernet0 fail-1/2
key changeover *.
failover interface ip fail-1 10.3.1.21 255.255.255.252 watch 10.3.1.22
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 66114.bin
enable ASDM history
ARP timeout 14400
NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.4.1.0_28 NETWORK_OBJ_10.4.1.0_28 non-proxy-arp-search to itinerary
!
NAT source auto after (indoor, outdoor) dynamic one interface
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 187.217.68.145 1
Route inside 10.0.0.0 255.0.0.0 10.1.1.78 1
Route inside 150.211.0.0 255.255.0.0 10.1.1.78 1WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-3.1.00495-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal GroupPolicy_VPN_ group strategy
attributes of Group Policy GroupPolicy_VPN_
WINS server no
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
dominio.com.MX value by default-field
type tunnel-group VPN_ remote access
attributes global-tunnel-group VPN_
address VPN_POOL pool
Group Policy - by default-GroupPolicy_VPN_
tunnel-group VPN_ webvpn-attributes
enable VPN_ group-alias
!I m don't know if Im missing a few small details or Setup. Any help will be much appreciated.
Thank you!!!Hello
When you use full VPN Tunnel (which is the default setting), you will have a number of things that you need to configure on the SAA.
First, the ASA by default will not allow traffic to enter via an interface and then exit through the same interface. It is essentially, what happens when the customer VPN traffic comes to the ASA and then heads on the Internet. In your case the traffic goes through the 'outside' and leaves via the 'outside' interface.
You will need this command
permit same-security-traffic intra-interface
You can check if their licence at the moment with the command
See the race same-security-traffic
Second, VPN users will need to have the NAT configuration like all users LAN behind the ASA real. So you basically configure dynamic PAT for 'outside' to 'outside' traffic
You can get there with the following configuration
network of the VPN-PAT object
subnet 10.4.1.0 255.255.255.240
dynamic NAT interface (outdoors, outdoor)
I suppose it should do for you to be able to connect to the Internet and the LAN when the VPN is active.
Hope this helps
Let me know how it goes.
-Jouni
-
AnyConnect vpn and a tunnel vpn Firewall even outside of the interface.
I have a (no connection) remote access vpn and ipsec tunnel connection to return to our supplier is on the same firewall outside interface.
The problem is when users remote vpn in they are not able to ping or join the provider above the tunnel network.
now, I understand that this is a Bobby pin hair or u turn due to traffic but I'm still not able to understand how the remote vpn users can reach the network of the provider on the tunnel that ends on the same interface where remote access vpn is also configured.
The firewall is asa 5510 worm 9.1
Any suggestions please.
Hello
You are on the right track. Turning U will be required to allow vpn clients access to resources in the L2L VPN tunnel.
The essence is that the split tunneling to access list must include subnets of the remote VPN to peer once the user connects they have directions pertaining to remote resources on anyconnect VPN
Please go through this post and it will guide you how to set up the u turn on the SAA.
https://supportforums.Cisco.com/document/52701/u-turninghairpinning-ASAKind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Cisco ASA Site to Site VPN IPSEC and NAT question
Hi people,
I have a question about the two Site to Site VPN IPSEC and NAT. basically what I want to achieve is to do the following:
ASA2 is at HQ and ASA1 is a remote site. I have no problem setting a static static is a Site to IPSEC VPN between sites. Guests residing in 10.1.0.0/16 are able to communicate with hosts in 192.168.1.0/24, but what I want is to configure the NAT with IPSEC VPN for this host to 10.1.0.0/16 will communicate with hosts in 192.168.1.0/24 with translated addresses
Just an example:
N2 host (10.1.0.1/16) contacted N1 192.168.1.5 with destination host say 10.23.1.5 No 192.168.1.5 (notice the last byte is the same in the present case,.5)
The translation still for the rest of the communication (host pings ip destination host 10.23.1.6 N3 N2 not 192.168.1.6 new last byte is the same)
It sounds a bit confusing to me, but I've seen this type of configuration before when I worked for the supplier of managed services where we have given our customers (Ipsec Site to Site VPN with NAT, don't know how it was setup)
Basically we contact the customer via site-to-site VPN hosts but their real address were hidden and we used as translated address more high 10.23.1.0/24 instead of (real) 192.168.1.0/24, last byte must be the same.
Grateful if someone can shed some light on this subject.
Hello
OK so went with the old format of NAT configuration
It seems to me that you could do the following:
- Configure the ASA1 with static NAT strategy
- access-list L2LVPN-POLICYNAT allowed ip 192.168.1.0 255.255.255.0 10.1.0.0 255.255.0.0
- public static 10.23.1.0 (inside, outside) access-list L2LVPN-POLICYNAT
- Because the above is a static NAT of the policy, this means that the translation will be made only when the destination network is 10.1.0.0/16
- If you have for example a PAT basic configuration to inside-> external traffic, the above NAT configuration and the custom of the actual configuration of PAT interfere with eachother
- ASA2 side, you can normally configure NAT0 / NAT Exemption for the 10.1.0.0/16 network
- Note of the INTERIOR-SHEEP access-list SHEEP L2LVPN
- the permitted INSIDE SHEEP 10.1.0.0 ip access list 255.255.0.0 10.23.1.0 255.255.255.0
- NAT (inside) 0-list of access to the INTERIOR-SHEEP
- You will need to consider that your access-list defining the VPN encrypted L2L traffic must reflect the new NAT network
- ASA1: allowed to access-list L2LVPN-ENCRYPTIONDOMAIN ip 10.23.1.0 255.255.255.0 10.1.0.0 255.255.0.0
- ASA2: list L2LVPN-ENCRYPTIONDOMAIN allowed ip 10.1.0.0 access 255.255.0.0 10.23.1.0 255.255.255.0
I could test this configuration to work tomorrow but I would like to know if it works.
Please rate if this was helpful
-Jouni
- Configure the ASA1 with static NAT strategy
-
VPN IPSec with no. - Nat and Nat - No.
On a 6.3 (5) PIX 515 that I currently have an IPSec VPN configured with no. - nat, using all public IPs internally and on the remote control. Can I add two hosts to the field of encryption that have private IP addresses and NAT to the same public IP in the address card Crypto? What commands would be involved in this?
Current config:
-------
ipsectraffic_boston list of allowed access host ip host PublicIP11 PublicIP1
ipsectraffic_boston list of allowed access host ip host PublicIP22 PublicIP2
outside2_outbound_nat0_acl list of allowed access host ip host PublicIP PublicIP
card crypto mymap 305 correspondence address ipsectraffic_boston
mymap 305 peer IPAdd crypto card game.
mymap 305 transform-set ESP-3DES-SHA crypto card game
life card crypto mymap 305 set security-association seconds 86400 4608000 kilobytes---------
I would add two IP private to the 'ipsectraffic_boston access-list' and have NAT to a public IP address, as the remote site asks that I don't use the private IP. This would save the effort to add a public IP address to my internal host.
Thank you
Dan
Hello
If for example you have an internal host 192.168.1.1 and you want NAT public IP 200.1.1.1 it address
You can make a static NAT:
(in, out) static 200.1.1.1 192.168.1.1
And include the 200.1.1.1 in crypto ACL.
Federico.
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
Maybe you are looking for
-
When can I remove photos from the iPhone by making sure they are saved in the cloud?
When I can I free up space on my iPhone 6, deletion of photos/videos, ensure that they are saved in the cloud?When I buy more space on the cloud, it is to iCloud, iCloud Drive, iCloud photo library?Too confusing...
-
Trial download MS Access where and how
Our office staff would like to know where to go to download a trial version of MS Access? Someone knows
-
Solution to remove the message from the installer
I downloaded the drivers from the HP website for my B209a Photosmart more that the printer no longer works. I now have the HP message that says to uninstall because the installation was not successful. My firewall allowed me to stop it install but
-
.. .or is not possible, and it is best to think about to buy a new printer! I was wasting far too much time trying to set up many "good drivers" for this device and will never work ok My question is simple: "there is a device that works well with HP
-
Theme generator 6: error icons support
When I export my theme built on the model of BlackBerry 6, icons in the media get tab disappeared. other wherelse all tabs, Favorites, downloads work perfectly. Someone at - it solved this problem?