Tunnel VPN failure traps
Does anyone know if an ASA5505 sends a trap when / if a L2L tunnel fails?
We are about to use the L2L tunnel as our backup route and it would be really nice if we had notification when / if the tunnel down.
You have got it. Which for webvpn/anyconnect. I'm sure that for the L2L tunnels it has already activated (and not seen in the \windows\system32\conifg\system).
Tags: Cisco Security
Similar Questions
-
Impossible to access them Internert through the split tunneling VPN client.
I divided tunnel configured on a PIX 515. The remote VPN client connects to the PIX very well and can ping hosts on the internal network, but cannot access the Internet. Am I missing something? My config as shown below.
In addition, I don't see the routes on the VPN client via statistics (screenshot below)
All opinions are appreciated.
Rob
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------
8.0 (3) version PIX
!
hostname PIX-to-250
enable the encrypted password xxxxx
names of
!
interface Ethernet0
nameif outside
security-level 0
IP address x.x.x.250 255.255.255.240
!
interface Ethernet1
nameif inside
security-level 100
IP 192.168.9.1 255.255.255.0
!
XXXXX encrypted passwd
passive FTP mode
DNS domain-lookup outside
DNS server-group Ext_DNS
Server name 194.72.6.57
Server name 194.73.82.242
the LOCAL_LAN object-group network
object-network 192.168.9.0 255.255.255.0
object-network 192.168.88.0 255.255.255.0
Internet_Services tcp service object-group
port-object eq www
area of port-object eq
EQ object of the https port
port-object eq ftp
EQ object of port 8080
port-object eq telnet
the WAN_Network object-group network
object-network 192.168.200.0 255.255.255.0
ACLOUT list extended access allowed object-group LOCAL_LAN udp any eq log field
ACLOUT list extended access allow icmp object-group LOCAL_LAN no matter what paper
ACLOUT list extended access permitted tcp object-group LOCAL_LAN connect to any object-group Internet_Services
access-list extended ACLIN all permit icmp any what newspaper echo-reply
access-list extended ACLIN all permit icmp any how inaccessible journal
access-list extended ACLIN allowed icmp no matter what newspaper has exceeded the time
Comment by split_tunnel_list-LAN Local access list
split_tunnel_list list standard access allowed 192.168.9.0 255.255.255.0
access-list extended SHEEP allowed object-group ip LOCAL_LAN 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
Outside 1500 MTU
Within 1500 MTU
IP local pool testvpn 192.168.100.1 - 192.168.100.99
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list SHEEP
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group ACLIN in interface outside
ACLOUT access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 195.171.252.45 1
Route inside 192.168.88.0 255.255.255.0 192.168.88.254 1
Route inside 192.168.199.0 255.255.255.0 192.168.199.254 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac Set_1
Crypto-map dynamic outside_dyn_map 10 game of transformation-Set_1
life together - the association of security crypto dynamic-map outside_dyn_map 10 seconds 280000
Crypto-map dynamic outside_dyn_map 10 the value reverse-road
outside_map 10 card crypto ipsec-isakmp dynamic outside_dyn_map
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
internal testvpn group policy
attributes of the strategy of group testvpn
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
name of user testuser encrypted password xxxxxx
type tunnel-group testvpn remote access
tunnel-group testvpn General-attributes
address testvpn pool
Group Policy - by default-testvpn
testvpn group of tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:5dcb5dcdff277e1765a9a0c366b88b9e
: end
# 250 A - PIX
You have not assigned the ACL split tunnel to your strategy.
PLS, configure the following:
attributes of the strategy of group testvpn
value of Split-tunnel-network-list split_tunnel_list
-
Hello. I'm creating a tunnel VPN IPSec LAN - to - LAN of my ASA5510 to another network but met an obstacle bit. My counterpart on the other side has informed me that he already has a VPN tunnel to another company that has the same IP range as my network(10.100.16.0 /24) and can not create the tunnel.
I was wondering is it possible to use NAT on the VPN tunnel so that traffic that goes from my network over the VPN tunnel gets translated and my counterpart on the other side sees this reflects the range of IP addresses?
Thanks in advance for any help.
Hello
Yes, you can use the same address you already use for internet access.
Just update your list of access crypto to reflect the new address and to ensure that the third party did the same.
Jon
-
Tunnel VPN site to Site with 2 routers Cisco 1921
Hi all
So OK, I'm stumped. I create much s2s vpn tunnels before, but this one I just can't go there. It's just a tunnel VPN Site to Site simple using pre-shared keys. I would appreciate it if someone could take a look at our configs for both routers running and provide a comment. This is the configuration for both routers running. Thank you!
Router 1
=======
Current configuration: 4009 bytes
!
! Last configuration change at 19:01:31 UTC Wednesday, February 22, 2012 by asiuser
!
version 15.0
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
SJWHS-RTRSJ host name
!
boot-start-marker
boot-end-marker
!
!
No aaa new-model
!
!
!
!
No ipv6 cef
IP source-route
IP cef
!
!
DHCP excluded-address 192.168.200.1 IP 192.168.200.110
DHCP excluded-address IP 192.168.200.200 192.168.200.255
!
IP dhcp POOL SJWHS pool
network 192.168.200.0 255.255.255.0
default router 192.168.200.1
10.10.2.1 DNS server 10.10.2.2
!
!
no ip domain search
IP-name 10.10.2.1 Server
IP-name 10.10.2.2 Server
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki trustpoint TP-self-signed-236038042
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 236038042
revocation checking no
rsakeypair TP-self-signed-236038042
!
!
TP-self-signed-236038042 crypto pki certificate chain
certificate self-signed 01
30820241 308201AA A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
8B1E638A EC
quit smoking
license udi pid xxxxxxxxxx sn CISCO1921/K9
!
!
!
redundancy
!
!
!
!
crypto ISAKMP policy 10
md5 hash
preshared authentication
ISAKMP crypto key presharedkey address 112.221.44.18
!
!
Crypto ipsec transform-set esp-3des esp-md5-hmac IPSecTransformSet1
!
map CryptoMap1 10 ipsec-isakmp crypto
defined by peer 112.221.44.18
game of transformation-IPSecTransformSet1
match address 100
!
!
!
!
!
interface GigabitEthernet0/0
192.168.200.1 IP address 255.255.255.0
automatic duplex
automatic speed
!
!
interface GigabitEthernet0/1
Description wireless bridge
IP 172.17.1.2 255.255.255.0
automatic duplex
automatic speed
!
!
interface FastEthernet0/0/0
Verizon DSL description for failover of VPN
IP 171.108.63.159 255.255.255.0
automatic duplex
automatic speed
card crypto CryptoMap1
!
!
!
Router eigrp 88
network 172.17.1.0 0.0.0.255
network 192.168.200.0
redistribute static
passive-interface GigabitEthernet0/0
passive-interface FastEthernet0/0/0
!
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP route 0.0.0.0 0.0.0.0 172.17.1.1
IP route 112.221.44.18 255.255.255.255 171.108.63.1
!
access-list 100 permit ip 192.168.200.0 0.0.0.255 10.10.0.0 0.0.255.255
!
!
!
!
!
!
control plan
!
!
!
Line con 0
Synchronous recording
local connection
line to 0
line vty 0 4
exec-timeout 30 0
Synchronous recording
local connection
transport input telnet ssh
!
Scheduler allocate 20000 1000
end
=======
Router 2
=======
Current configuration: 3719 bytes
!
! Last configuration change at 18:52:54 UTC Wednesday, February 22, 2012 by asiuser
!
version 15.0
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
SJWHS-RTRHQ host name
!
boot-start-marker
boot-end-marker
!
logging buffered 1000000
!
No aaa new-model
!
!
!
!
No ipv6 cef
IP source-route
IP cef
!
!
!
!
no ip domain search
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki trustpoint TP-self-signed-3490164941
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 3490164941
revocation checking no
rsakeypair TP-self-signed-3490164941
!
!
TP-self-signed-3490164941 crypto pki certificate chain
certificate self-signed 01
30820243 308201AC A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
EA1455E2 F061AA
quit smoking
license udi pid xxxxxxxxxx sn CISCO1921/K9
!
!
!
redundancy
!
!
!
!
crypto ISAKMP policy 10
md5 hash
preshared authentication
ISAKMP crypto key presharedkey address 171.108.63.159
!
86400 seconds, duration of life crypto ipsec security association
!
Crypto ipsec transform-set esp-3des esp-md5-hmac IPSecTransformSet1
!
map CryptoMap1 10 ipsec-isakmp crypto
defined by peer 171.108.63.159
game of transformation-IPSecTransformSet1
match address 100
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
automatic duplex
automatic speed
!
!
interface GigabitEthernet0/0.1
encapsulation dot1Q 1 native
IP 10.10.1.6 255.255.0.0
!
interface GigabitEthernet0/1
IP 172.17.1.1 255.255.255.0
automatic duplex
automatic speed
!
!
interface FastEthernet0/0/0
IP 112.221.44.18 255.255.255.248
automatic duplex
automatic speed
card crypto CryptoMap1
!
!
!
Router eigrp 88
Network 10.10.0.0 0.0.255.255
network 172.17.1.0 0.0.0.255
redistribute static
passive-interface GigabitEthernet0/0
passive-interface GigabitEthernet0/0.1
!
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP route 0.0.0.0 0.0.0.0 112.221.44.17
!
access-list 100 permit ip 10.10.0.0 0.0.255.255 192.168.200.0 0.0.0.255
!
!
!
!
!
!
control plan
!
!
!
Line con 0
Synchronous recording
local connection
line to 0
line vty 0 4
exec-timeout 30 0
Synchronous recording
local connection
transport input telnet ssh
!
Scheduler allocate 20000 1000
end
When the GRE tunnel carries your traffic to private ip range, your ACL must contain address of the host of point to point the IPSec tunnel.
Since then, both routers are running EIGRP in the corporate network, let the EIGRP Exchange routes via GRE tunnel, which is a good practice, rather than push the ip ranges private individual through the IPSec tunnel.
Let me know, if that's what you want.
Thank you
-
Tunnel VPN RV-042 for Dual WAN Failover backup function
We have customers with dual WAN failover scenarios with site-to-site VPN tunnels.
In the past, the VPN tunnel backup feature has been available in the RV-082.
One of the new RV-042 firmware versions have the function of backup Tunnel VPN available?
The feature is supported on the RV042 V3 hardware.
-
Tunnel VPN from Site to Site dynamic
I spent the last 2 days, try to set up a dynamic tunnel VPN site to site of a Cisco 5510 to a Cisco SA540. The 540 is a dynamic supplier that can not be changed. There a dyndns account.
I was lucky that the other 10 sites are all static and the ADSM Assistant creates these tunnels without problems.
What I try to do is:
Is it possible to do it VIA ADSM?
If this isn't the case, someone please in detail can help with orders.
Kind regards
PP
Hello Paul,
This is possible thanks to the ASDM, but you do have to use some advanced settings:
Configuration > VPN Site to Site > advanced > Tunnel groups
It change the group called "DefaultL2LGroup" and add the brightness button before the SA540 (Note: all of your sites with dynamic IP addresses will have the same key communicated in advance, if you have IPSec VPN clients, it will be a good idea to use a different key).
Click ok and then apply.
Then go to Configuration > VPN Site to Site > advanced > Crypto Maps and add a new entry dynamic
Make sure that you match the phase 2 are on your SA540 (pictured ESP-AES-128-SHA), select a dynamic strategy and make the last sequence number (65535) then ok, apply.
Then go to Configuration > VPN Site to Site > advanced > IKE policies and make sure you have corresponding policies of the phase 1.
If no corresponding policy is found, add them.
Through CLI:
IKEv1 crypto policy 1
preshared authentication
aes encryption
sha hash
Group 2
Crypto-map dynamic outside_dyn_map 65535 set transform-set ESP-AES-128-SHA ikev1
CARD crypto ipsec-isakmp 65535 dynamic outside_dyn_map
IPSec-attributes tunnel-group DefaultL2LGroup
IKEv1 pre-shared-key *.
I hope this helps.
-
Bring up the tunnel vpn crypto without interesting traffic map
Is it possible on ASA to bring up the tunnel vpn site to site static crypto map without generating interesting traffic? I want to reverse route injection generate road dynamic until traffic begins to flow.
Roman,
Unless something chnaged recently RRI inserts routes without present SAs, meaning that they are static (in contrast to current default behavior on IOS 12.4 (9) T-I_think leave).
But to answer the question, in more recent versions, you can bring up the tunnel using packet - trace CLI.
M.
Edit: request for improvement that will present the same features of IPP on ASA as on IOS:
http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCsx67450
-
Tunnel VPN site to Site - aggressive Mode
I searched the community for answers to this and that you have not found quite what I was looking for (or what seems logical). I have an ASA 5510 to A site with one website VPN tunnel to a SonicWall to site B. Which works very well. I need to create a tunnel for site C to site a using a tunnel of aggressive mode. I'm not quite sure how to do this. Any suggestion would be great!
NOTE: I have included the parts of the running configuration that seem relevant to me. If I missed something please let me know.
ASA Version 8.2 (1)
interface Ethernet0/0
nameif outside
security-level 0
IP 1.2.3.4 255.255.255.248
!
10.5.2.0 IP Access-list extended site_B 255.255.255.0 allow 10.205.2.0 255.255.255.128
access extensive list ip 10.5.2.0 site_C allow 255.255.255.0 10.205.2.128 255.255.255.128
dynamic-access-policy-registration DfltAccessPolicy
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac 3des-sha1
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto VPN 30 card matches the address site_B
card crypto VPN 30 peer set 4.3.2.1
crypto VPN 30 the transform-set 3des-sha1 value card
card crypto VPN 40 corresponds to the address site_C
card crypto VPN. 40 set peer 8.7.6.5
crypto VPN. 40 the transform-set 3des-sha1 value card
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
crypto ISAKMP ipsec-over-tcp port 10000
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
tunnel-group 4.3.2.1 type ipsec-l2l
4.3.2.1 tunnel-group ipsec-attributes
pre-shared-key *.
tunnel-group 8.7.6.5 type ipsec-l2l
IPSec-attributes tunnel-group 8.7.6.5
pre-shared-key *.
David,
Please try this:
clear crypto ipsec its peer site_c_IP
clear configure VPN 40 crypto card
card crypto VPN 10 corresponds to the address site_C
card crypto VPN 10 set peer 8.7.6.5
crypto VPN 10 the transform-set 3des-sha1 value card
debug logging in buffered memory
capture drop all circular asp type
capture capin interface inside the match ip 10.5.2.0 255.255.255.0 10.205.2.128 255.255.255.128
After generating the traffic and INTERNAL of the machine behind the ASA:
view Journal | 10.205.2 Inc.
See the fall of cap. 10.205.2 Inc.
view Cape capin
In case it does not work:
(a) show the crypto classic table ASP.
(b) details of vpn-framework for table ASP.
(c) show cry its site_c peer ipsec
(d) entry packet - trace within the icmp 10.5.2.15 8 0 10.205.2.130 detail
(e) see the crypto ipsec his
At the same time, please.
Let me know how it goes.
Thank you
Portu.
Please note all useful posts
-
Can anyone help me how I will work with tunnel VPN Failover.
Hi Experts,
I have two 5520 ASA one headquarters and another is disaster recovery. So I need to build the tunnel of the Branch Office Chief at the office that I have 3g router.
So I need to build failover to ASA of recovery after a disaster. Please can someone help me what would be the best option that makes my task complete.
Thank you
Mohammed
Hello
I guess you are looking for a relief tunnel VPN router. Here's how you set it up:
I hope this helps.
Kind regards
Anisha
P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.
-
Recently I tried to build a tunnel VPN of LAN LAN 2 connecting an Asa to a current zone based firewall 2911. It's a standard IPSec psk tunnel nothing complicated. I got the tunnel to establish, but I could only get traffic to encap on the side of the SAA and decap on the side of 2911. I couldn't return circulation. I followed this doc classic here for IPSec in the last example.
http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps5708/ps5710/ps1018/...
And I don't know that the SAA is right I have built a ton of those but I am new to zfw. I don't see anything about a NAT rule exempt. But as all used real IPs instead of NAT I wasn't sure and I have found no info. I do free NAT? If If you are using a roadmap on the end you NAT overload line config as in the past?
I also have a pair of area to "self" and I didn't know if I need something there to be able to do a ping from inside the 2911 interface when the tunnel is at the top of the remote end. Thank you
Is the pair area yourself, outside of itself?
And you say that you do not use only NAT, have real addresses (public routable addresses?), so why you have to make an exception for NAT you have not?
-
Hello
I installed a tunnel VPN between ASA and PIX. I want to implement security on the ASA or PIX so that some remote endpoint specfic IP can access resources of tunnel. is it possible to block additional IP addresses?
Thank you
Amardeep
Please read this link, you can implement VPN-filter.
Thank you
Ajay
-
Hi all
IM challenges with a site to site vpn where it cannot be initiated/based on one side of the VPN.
For 1 side of the vpn, I could ping everywhere without problems and vpn tunnel is established successfully, but when I try it the other side of the vpn it never sets and the State is stuck in MM_KEY_EXCH.
I have verfied configurations at both ends and everything seems to be going well (see below), also, please find an isakmp crypto debugging attached to the router that does not seem to establish the vpn - no idea why this is a failure?
VPN is set up on a C837 to a C857.
***
crypto ISAKMP policy 10
the BA
md5 hash
preshared authentication
Group 2
secret key crypto ISAKMP address 81.140.73.140 No.-xauth
!
life 3000 seconds crypto ipsec security association
!
Crypto ipsec transform-set esp course - esp-md5-hmac
!
vpn 10 ipsec-isakmp crypto map
defined by peer 81.140.73.140
secure Set transform-set
match address VPN-traffic***
Thank you very much
That could very well be causing this problem.
If you have the static configuration to the dynamic for IPsec between two routers, please make sure that you have this configuration:
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080093f86.shtml
You see that the dynamic IP site has a normal static encryption card, but the side static IP has a dynamic encryption card.
This example assumes that you do NAT too.
With this configuration, the tunnel can only be started from the dynamic side.
It will be useful.
Federico.
-
Publish a server with NAT anchored through a tunnel VPN with ASA
Hi all
Thanks in advance for helping me out - I know somebody did, and I have trouble finding how do. I don't know that I'm missing something simple.
I have a client who wants to view a DVR device through a VPN tunnel that is published through the public firewall to collocation. Endpoint DVR is endpoint ip assigned dynamically which tunnelle the host on demand (I know that the tunnel could fall).
So I think / thought I could hairpin hair/policy nat this, but I'm not the best at this.
Let's see if I can get this
IP public 1.1.1.1\
> External interface of ASA
2.2.2.2 / private ip
My config as I know it is pertinant is as follows:
permit same-security-traffic intra-interface
list of allowed incoming access extended ip any host 168.215.x.x
Access-group interface incoming outside
public static 168.215.x.x (outside, outside) 10.10.x.xnetmask 255.255.255.255
I am running version 8.2.5 of the image of the SAA.
If you could take a look and let me know what Miss me you please.
Thank you
Hello
The problem here is of course the fact that we can not configure NAT0 without causing all traffic from the remote Internet can flow through the VPN connection.
So I wonder if another type of NAT configuration would actually work.
I would call it static political identity NAT if such a name exists yet.
Something like that
Note of DVR-POLICY-NAT-list of Direct HTTP access to VPN traffic
allow to Access-list DVR-POLICY-NAT tcp host 10.10.2.253 eq 80 a
public static 10.10.2.53 (inside, outside) access list DVR-POLICY-NAT
This should basically do what
- When the DVR is sending any traffic source TCP TCP/80 (essentially the traffic back to the connection from the main site) to ANY destination address (The Internet) then the host must translate to himself.
- If we consider that NAT is performed before the VPN rules are processed this should mean that since we have concerns address itself, it must match the VPN rule only in this particular case where the traffic is TCP/80, which could only be the result of her replying to a link any destination TCP/80)
- Which leads me to believe it shouldn't cause any problems with the Central connection on remote site (NAT0 is processed before political static NAT) or the RECORDER to Internet
- Unless the DVR must be accessible directly via the Internet connection of the remote site. (He would send his answers to these HTTP connections outside with the originating source IP address) Or maybe even completely before connecting the phase failure. I have not tested.
Hope this helps
Be sure to mark it as answered in the affirmative. And/or useful response rate.
Ask more if necessary.
EDIT: typos
-Jouni
-
Tunnel VPN IPSEC Gre of the router in the branch office by Pix to the router HQ
Hi all
I tried to get this scenario to work before I put implement but am getting the error on router B.
01:05:38: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode failed with the peer to 83.1.16.1
Here are the following details for networks
Router B
Address series 82.12.45.1/30
fast ethernet 192.168.20.1/24 address
PIX
outside the 83.1.16.1/30 interface eth0
inside 192.168.50.1/30 eth1 interface
Router
Fast ethernet (with Pix) 192.168.50.2/30 address
Loopback (A network) 192.168.100.1/24 address
Loopback (Network B) 192.168.200.1/24 address
Loopback (Network C) 192.168.300.1/24 address
Is could someone please tell me where im going wrong as I read the explanation of the error and it points to political unmaching. This has confused me like the two counterparts seem to have the same settings.
Config router B
======================
name of host B
!
Select the 5 secret goat.
!
username 7 privilege 15 password badger badger
iomem 15 memory size
IP subnet zero
!
!
no ip domain-lookup
IP - test.local domain name
!
property intellectual ssh delay 30
property intellectual ssh authentication-2 retries
!
crypto ISAKMP policy 5
md5 hash
preshared authentication
Group 2
ISAKMP crypto key VPN2VPN address 83.1.16.1
!
86400 seconds, duration of life crypto ipsec security association
!
Crypto ipsec transform-set esp - esp-md5-hmac VPN
!
crypto map 5 VPN ipsec-isakmp
defined by peer 83.1.16.1
PFS group2 Set
match address VPN
!
call the rsvp-sync
!
interface Loopback10
20.0.2.2 the IP 255.255.255.255
!
interface Tunnel0
bandwidth 1544000
20.0.0.1 IP address 255.255.255.0
source of Loopback10 tunnel
tunnel destination 20.0.2.1
!
interface FastEthernet0/0
Description * inside the LAN CONNECTION *.
address 192.168.20.1 255.255.255.0
IP nat inside
automatic duplex
automatic speed
!
interface Serial0/0
Description * INTERNET ACCESS *.
IP 88.12.45.1 255.255.255.252
NAT outside IP
VPN crypto card
!
interface FastEthernet0/1
no ip address
Shutdown
automatic duplex
automatic speed
!
Router eigrp 1
network 20.0.0.0
No Auto-resume
!
overload of IP nat inside source list NAT interface Serial0/0
IP classless
IP route 0.0.0.0 0.0.0.0 Serial0/0
no ip address of the http server
!
!
NAT extended IP access list
deny ip 192.168.20.0 0.0.0.255 192.168.200.0 0.0.0.255
deny ip 192.168.20.0 0.0.0.255 192.168.300.0 0.0.0.255
deny ip 192.168.20.0 0.0.0.255 192.168.100.0 0.0.0.255
ip licensing 192.168.20.0 0.0.0.255 any
list of IP - VPN access scope
permit ip host 20.0.2.2 20.0.2.1
!Config PIX
====================
PIX Version 7.2 (4)
!
pixfirewall hostname
names of
name 20.0.2.2 B_LOOP
name 88.12.45.1 B_WANIP
!
interface Ethernet0
Description * LINK to ISP *.
nameif outside
security-level 0
IP 83.1.16.1 255.255.255.252
!
interface Ethernet1
Description * LINK TO LAN *.
nameif inside
security-level 100
IP 192.168.50.1 255.255.255.252
!
passive FTP mode
the ROUTER_LOOPS object-group network
network-object 20.0.2.0 255.255.255.252
access allowed extended VPN ip host 20.0.2.1 B_LOOP list
access-list extended SHEEP permit ip host 20.0.2.1 ROUTER_LOOPS object-group
Access ip allowed any one extended list ACL_OUT
pager lines 24
Outside 1500 MTU
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global (1 interface external)
NAT (inside) 0 access-list SHEEP
NAT (inside) 1 192.168.50.0 255.255.255.252
NAT (inside) 1 192.168.50.0 255.255.255.0
Access to the interface inside group ACL_OUT
Route outside 0.0.0.0 0.0.0.0 83.1.16.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp - esp-md5-hmac VPN
86400 seconds, duration of life crypto ipsec security association
VPN 5 crypto card matches the VPN address
card crypto VPN 5 set pfs
card crypto VPN 5 set peer B_WANIP
VPN 5 value transform-set VPN crypto card
card crypto VPN 5 defined security-association life seconds 28800
card crypto VPN outside interface
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
tunnel-group 88.12.45.1 type ipsec-l2l
IPSec-attributes tunnel-group 88.12.45.1
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!When you create a GRE tunnel between two routers, there should be a routing decision to reach the Remote LAN through local (rather than exit directly the physical interface) tunnel interface.
This could be accomplished by EIGRP, but you can check if the adjacency is built.
As a test, what happens if you add a static route saying (reach remote LAN, sending traffic to the tunnel interface).
Check if the GRE tunnel comes up with sh interface tunnel
Federico.
-
Tunnel VPN Firewall (both sides of the Site B, same IP series)
Hi Experts,
I'm in a weird situation, hope I can get an answer from you guys.
I had created VPN tunnel to our customer on our firewall 3 years.
Now we create the VPN tunnel for new customer, but the IP settings to the new customer is the same as the former client. How can we get through this that we can not change the IP settings on both clients.
Here are the technical details
Older Client settings:
(1) our authorized Local LAN IP: 192.168.3.0/24
(2) customer Local LAN IP authorized: 10.0.0.0/8 (as several range of network to the client end)
New customer to make settings:
(1) our authorized Local LAN IP: 192.168.3.0/24
(2) authorized customer Local LAN IP: 10.10.16.0/24
10.10.32.0/24
Please help as well how we can make the settings without making any changes on the client side.
I am using firewall Watchguard XTM 515
Thank you best regards &,.
Mandeep
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)*
Maybe you are looking for
-
Text sound signals are emitted when I test them, but not when a text comes in. installed 9.2.1 I have turned on and off and tried different ringtones and it does not always sound.
-
Pro 3 yoga and Hibernation power button
Hello I have a problem with turn on the laptop after that it goes the way standby mode Hibernate (no doubt). Since the beginning, I installed Win clean 10 with the latest drivers of Yoga. Now when I put the Yoga sleep (power button flashes) and after
-
MAX: Devices & Interfaces missing from the tree?
Hi all I'm a noob and try to learn LV I'm working through the book, Labview for everyone, and I work in the chapter on the instrument control. I opened MAX (Measurement and Automation Explorer) and want to see the ports on my computer. It is said in
-
I encounter an error code 52D when updated security installed for mircosoft work 8 (KB973636).
I always install the update to my Windows vista through the automatic update system, but recently I encounters an error code 52D when updated security installed for mircosoft work 8 (KB973636). Please help someone... seem micrsoft don have send to as
-
Used Backup Wizard, then finished the message "insert disc" popped up. I inserted the disc, closed the door and waited at least 15 minutes. "Insert disc" was still there! Try to save and drive D won't let me!