Two signals interfering with each other
Hello
I have a problem with a trace of pressure and a vibration sensor. I have a card PCIe - 6341 DAQ. I connect my pressure signal to a channel (say ach0) and I connect the vibration to another analog channel (say ach7).
In labview, I use an assistant DAQ. When I use it to sample only one of the signals, there is no problem. If I add two channels in the configuration dialog box, the signal pressure becomes superimposed vibration signal.
Analog signals entering data show no interference (checked with an oscilloscope). I suspect that what is happening inside the data acquisition card.
Any ideas why this happens?
Thank you
Masoud Mashkournia
Hi Masoud,
It seems that you see 'ghosts' on your channels. The 6341 multiplex via the analog inputs. Therefore, if you are scanning between high voltage and low voltage, especially when you use CSR, you can see ghost images if the signal from the previous channel file completely or have a path to the ground. Here is a good article from the knowledge base that describes ways of eliminating this remanence.
I noticed that you use the configuration of the CSR on your DAQ Configuration Wizard. Try using a differential input configuration. This can help eliminate unwanted common mode voltages. In addition, you can try place a middle way in scanning which is connected to the ground at AIGND in the DAQ command scan. This can help with the mass of the previous signal. Most likely, you will want to scan in this order: pressure, ground, vibrations.
Please let me know if it helps.
Best,
Tags: NI Hardware
Similar Questions
-
How can I cut my two Gmail accounts with each other.
Hello
Whenever I connect to my Gmail account, I get the warning that there was a new sign from Firefox on Windows.
I don't know why, but I get the same message on another Gmail account that I have not signed in to.
In fact, on my mobile, I've set up these two Gmail accounts and I always switch between them.
On my laptop, I always sign in to account by time, while on my laptop I am connected at the same time, all the time.
How can I disconnect the two accounts, so that the e-mail, which belongs to the old, will not be sent to the latter, as well?
I would like to disconnect them on my laptop and on my laptop.
Thank you
Francis UK
Hello Francois,.
Thank you for visiting Microsoft Community and we provide a detailed description of the issue.
According to the description, I understand that you experience the problem when you try to connect to the Gmail account, you get the warning that there was a new GIS in Firefox on Windows. Now, you want to know how to disconnect the two accounts so that the e-mail which belongs to the former will not be sent to the latter.
Certainly, I understand your concern and will try my best to help you.
In order to get more help on this issue, you can post your query on the forum of Gmail. Please see the links below.
https://productforums.Google.com/Forum/#! Forum/gmail
https://support.Google.com/mail/?hl=en#topic=3394144
I hope this information is useful.
Please let us know if you need more help, we will be happy to help you.
Thank you.
-
Two buttons reacting with each other
Hello
I have a page where I use icons in the middle and a downstairs main navigation bar. Both have the same links.
I hope to somehow connect these two. So that when you rollover say icon 'products', the text of 'products' in the navigation bar would emphasize and so on...
My buttons are just converted symbols, not actionscript used to do rather than stop.
see you soon,
Spawn
Google is the best place to search for tutorials, but it's pretty simple so that you won't have a tutorial.
you create a movieclip and frame 1, you attach a stop() to the framework and graphics 'up '. create a 'more' (and if you want a 'low' setting). If you graduate your frames in the obvious way you then use:
{yourbutton.onRollOver = function ()}
this.gotoAndStop ("over");
}
{yourbutton.onRollOut = function ()}
this.gotoAndStop ("up");
}
-
Two Xbox 360 Wireless controllers Microsoft will interfere with each other?
* Original title: Microsoft Xbox 360 for Windows wireless controllers... Two will interfere with each other?
Controller: Microsoft Xbox 360 Wireless Controller for Windows (JR9-00011)
Operating systems: Windows 7
I have two PCs located in the same room. Is it possible to set up a wireless for each of them so that they do not interfere with each other?
Hello
I would like the links and see if it helps.
How to set up your Xbox 360 to your Windows PC controller
Set up your Xbox 360 for Windows gamepad
If you have other questions, please post your request in the Xbox forums for assistance on this issue.
Hope this information helps.
-
Hi all
I have 5 wireless devices must connect to the router.
I want to divide it into 2 groups:
That is to say, 1, device A, B, C, group 2, device D, E.
I would like two groups cannot communicate with each other.
I've heard, it can be done by VLAN, is e2500 can adapt to what I need?
What about EA3500 and EA4500?
I use G wireless, is what it means that ea4500 is out of choice even if it supports VLAN?
Thank you all!
Evil
Thanks for the clarification for the OP
FWIW
is this an alternative to routers that do not support of VLAN, to do what you want
-
AnyConnect Clients cannot communicate with each other
I have a problem that I've been pulling my hair out... my teleworkers connect to our network of Corp. via a connection AnyConnect VPN (version 3.1) to a Cisco ASA5520. I have not split tunneling enabled for this profile, so that all traffic should pass through the tunnel and all guests are in the same subnet L3... as far as their IP VPN address goes. The problem is the teleworker PCs cannot communicate with each other (pings/RDP/etc.). When I look at the newspaper I see traffic from one to another, have denied anything, but they do not communicate. My Network Corp., I can communicate with the two PCs Anyconnect very well. When I go to monitoring. ASDM itineraries I see each host that is connected to the ASA via Anyconnect, and the gateway for each is the default gateway of the SAA.
Am I missing some setting in the VPN profile that prevents the access between these hosts? I think that something come in the newspaper...
Have you enabled crossed and also a free NAT between AnyConnect users?
permit same-security-traffic intra-interface
network of the AnyConnect_users object
subnet
public static AnyConnect_users AnyConnect_users destination NAT (outside, outside) static source AnyConnect_users AnyConnect_users
If this does not resolve your problem, please post a sanitized complete configuration of your ASA.
-
List boxes drop-down interfearing with each other
HE SOLVED. / Tobias
Hello
When I use two combo boxes with the code adobe (from Component Explorer Flex) example they interfere with each other. When I make a choice in a box the choice I made in the other disappears from the box. How can I change the code to avoid that / or do I have to use a different configuration with the code?
Can someone please explain how to reach Code correctly (can't find no & amp; quot; a button insert code & amp; quot; or similar)
Se my example:
& amp; amp; Lt;? XML version = & amp; amp; quot; 1.0 & amp; amp; quot; Encoding = & amp; amp; quot; UTF - 8 & amp; amp; quot;? & amp; amp; GT;
& amp; amp; Lt; xmlns:mx = MX:application & amp; amp; quot; http://www.Adobe.com/2006/MXML & amp; amp; quot; page = & amp; amp; quot; absolute & amp; amp; quot; & amp; amp; GT;
& amp; amp; Lt; MX:script & amp; amp; GT;
& amp; amp; Lt;! [CDATA]
[Bindable]
public var vinalternativ: Array = [{label: & amp; amp; quot; 1 glas husets & amp; amp; quot; wine: 65}, {label: & amp; amp; quot; 2 glas husets & amp; amp; quot; wine: 130}, {label: & amp; amp; quot; dryckespaket 3 ratters & amp; amp; quot; wine: 230}];
[Bindable]
public var sluttider: Array = [{label: & amp; amp; quot; 24,00 & amp; amp; quot; data: 0}, {label: & amp; amp; quot; 01.00 & amp; amp; quot; data: 1500}, {label: & amp; amp; quot; 02.00 & amp; amp; quot; data: 3000}];
[Bindable]
public var selectedItem:Object;
]] & amp; amp; GT;
& amp; amp; Lt; / mx:Script & amp; amp; GT;
& amp; amp; Lt;! -first combo - & amp; amp; GT;
& amp; amp; Lt; id = MX:ComboBox & amp; amp; quot; ComboBox2 & amp; amp; quot; x = & amp; amp; quot; 86 & amp; amp; quot; y = & amp; amp; quot; 73 & amp; amp; quot; dataProvider = & amp; amp; quot; {sluttider} & amp; amp; quot; close = & amp; amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; amp; quot; width = & amp; amp; quot; 106 & amp; amp; quot; / & amp; amp; GT;
& amp; amp; Lt; id = MX:textarea & amp; amp; quot; lokalhyra & amp; amp; quot; x = & amp; amp; quot; 289 & amp; amp; quot; y = & amp; amp; quot; 74 & amp; amp; quot; width = & amp; amp; quot; 70 & amp; amp; quot; height = & amp; amp; quot; 22 & amp; amp; quot; text = & amp; amp; quot; {selectedItem.data} & amp; amp; quot; / & amp; amp; GT;
& amp; amp; Lt;! --deuxieme combo - & amp; amp; GT;
& amp; amp; Lt; id = MX:ComboBox & amp; amp; quot; vinCombo & amp; amp; quot; dataProvider = & amp; amp; quot; {vinalternativ} & amp; amp; quot; close = & amp; amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; amp; quot; x = & amp; amp; quot; 86 & amp; amp; quot; y = & amp; amp; quot; 139 & amp; amp; quot; width = & amp; amp; quot; 106 & amp; amp; quot; / & amp; amp; GT;
& amp; amp; Lt; id = MX:textarea & amp; amp; quot; vinval & amp; amp; quot; x = & amp; amp; quot; 289 & amp; amp; quot; y = & amp; amp; quot; 140 & amp; amp; quot; width = & amp; amp; quot; 70 & amp; amp; quot; height = & amp; amp; quot; 22 & amp; amp; quot; text = & amp; amp; quot; {selectedItem.wine} & amp; amp; quot; / & amp; amp; GT;
& amp; amp; Lt; / mx:Application & amp; amp; GT;
HE SOLVED. / Tobias
Hello
When I use two combo boxes with the code adobe (from Component Explorer Flex) example they interfere with each other. When I make a choice in a box the choice I made in the other disappears from the box. How can I change the code to avoid that / or do I have to use a different configuration with the code?Can someone please explain how to reach Code correctly (can't find no & quot; Insert button code & quot; or similar)
Se my example:
& amp; Lt;? XML version = & amp; quot; 1.0 & amp; quot; Encoding = & amp; quot; UTF - 8 & amp; quot;? & amp; GT;
& amp; Lt; xmlns:mx = MX:application & amp; quot; http://www.Adobe.com/2006/MXML & amp; quot; page = & amp; quot; absolute & amp; quot; & amp; GT;
& amp; Lt; MX:script & amp; GT;
& amp; Lt;! [CDATA]
[Bindable]
public var vinalternativ: Array = [{label: & amp; quot; 1 glas husets & amp; quot; wine: 65}, {label: & amp; quot; 2 glas husets & amp; quot; wine: 130}, {label: & amp; quot; dryckespaket 3 ratters & amp; quot; wine: 230}];[Bindable]
public var sluttider: Array = [{label: & amp; quot; 24,00 & amp; quot; data: 0}, {label: & amp; quot; 01.00 & amp; quot; data: 1500}, {label: & amp; quot; 02.00 & amp; quot; data: 3000}];[Bindable]
public var selectedItem:Object;
]] & amp; GT;
& amp; Lt; / mx:Script & amp; GT;& amp; Lt;! -first combo - & amp; GT;
& amp; Lt; id = MX:ComboBox & amp; quot; ComboBox2 & amp; quot; x = & amp; quot; 86 & amp; quot; y = & amp; quot; 73 & amp; quot; dataProvider = & amp; quot; {sluttider} & amp; quot; close = & amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; quot; width = & amp; quot; 106 & amp; quot; / & amp; GT;
& amp; Lt; id = MX:textarea & amp; quot; lokalhyra & amp; quot; x = & amp; quot; 289 & amp; quot; y = & amp; quot; 74 & amp; quot; width = & amp; quot; 70 & amp; quot; height = & amp; quot; 22 & amp; quot; text = & amp; quot; {selectedItem.data} & amp; quot; / & amp; GT;& amp; Lt;! --deuxieme combo - & amp; GT;
& amp; Lt; id = MX:ComboBox & amp; quot; vinCombo & amp; quot; dataProvider = & amp; quot; {vinalternativ} & amp; quot; close = & amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; quot; x = & amp; quot; 86 & amp; quot; y = & amp; quot; 139 & amp; quot; width = & amp; quot; 106 & amp; quot; / & amp; GT;
& amp; Lt; id = MX:textarea & amp; quot; vinval & amp; quot; x = & amp; quot; 289 & amp; quot; y = & amp; quot; 140 & amp; quot; width = & amp; quot; 70 & amp; quot; height = & amp; quot; 22 & amp; quot; text = & amp; quot; {selectedItem.wine} & amp; quot; / & amp; GT;
& amp; Lt; / mx:Application & amp; GT; -
Microsoft 3000 wireless keyboards; they will interact with each other
I have 2 PC and I would like to replace the wired keyboards for 2 sets of Microsoft 3000 keyboard, will they interact with each other and can I change Ch / Freq of the units
Hi Baz,
Each keyboard has different frequency and will not interact with each other.
-
Hi, I have the browser explorer Firefox and Internet on my laptop, a friend told me that they will be in conflict with each other. the question is what I would do abouth this.
Your friend has any idea. Both work very well.
-
ASA - Tunnel all traffic, allow rays to communicate with each other
Well, I hope someone can help me with this headache! Switching to employ a PIX and VPN 3005 concentrator Office at home in an ASA5510 for firewall and IPSEC tunnels. It is pretty much a
- VPN on a stick, multiple rays.
- All traffic sent by tunnel
- Internet access through main office (using the web filter) of
- VOIP to VOIP between rays
- All departments are using the clients VPN 3005 HW or ASA 5505 s
HEADQUARTERS: 10.0.0.0/24
Speaks 1: 192.168.11.0 / 24
Speaks 2: 192.168.12.0 / 24
Speaks 3: 192.168.13.0 / 24
-continues to 192.168.31.0 / 24
Spoke with the current configuration, 1 can communicate with all the resources in the home, office and Internet integrated properly checked by a tracert. However, the rays cannot communicate with each other. This is required for VOIP traffic, when all TALK TALK calls are made (sites).
Logging information when talk of talks initiated icmp:
- No group of translation found for icmp src, dst outside: 192.168.31.1 inside: 192.168.11.1 (type 8, code 0)
If I remove the nat (outside) 1 192.168.0.0 255.255.00 - rays will begin to respond to each other, but then the rays cannot tunnel through the Home Office Internet traffic. My brain is so scrambled after the cramming of VPN configurations for these days, so I hope someone has an idea. I've always used concentrators 3005, so it's a little different! In the search for documentation for this configuration, I was surprised that this isn't a most common topology. It seems that this article would (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805734ae.shtml), but there is no rays! In any case, I'm sure this has something to do with NAT rules and perhaps who need access for traffic list speaks of talking.
=============================================
ASA Version 8.2 (1)
!
hostname asa5510interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP address 97.65.x.x 255.255.255.224interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.0.0.40 255.255.0.0permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
the DM_INLINE_NETWORK_1 object-group network
object-network 10.0.0.0 255.255.0.0object-network 192.168.0.0 255.255.0.0
access-list sheep extended ip 10.0.0.0 allow 255.255.0.0 192.168.0.0 255.255.0.0
Allow Access-list extended wccp servers ip host 10.0.0.83 a
Redirect traffic extended access-list deny ip any object-group DM_INLINE_NETWORK_1
Redirect traffic scope permitted any one ip access-list
Global 1 interface (outside)
NAT (outside) 1 192.168.0.0 255.255.0.0
NAT (inside) 0 access-list sheep
NAT (inside) 1 10.0.0.0 255.255.0.0Route outside 0.0.0.0 0.0.0.0 97.65.x.x 1
Route inside 192.168.0.0 255.255.255.0 10.0.0.1 1
Route inside 192.168.2.0 255.255.255.0 10.0.0.1 1
Route inside 192.168.3.0 255.255.255.0 10.0.0.1 1Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto ipsec df - bit clear-df outdoorsCrypto-map dynamic dynmap 1 transform-set RIGHT
map mymap 65535-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400crypto ISAKMP ipsec-over-tcp port 10000
management-access inside
a basic threat threat detection
no statistical access list - a threat detection
no statistical threat detection tcp-interceptionWCCP web cache redirect-list Redirect-traffic group-list password xxxxxxx wccp-servers
WCCP 90 redirect-list traffic Redirect wccp servers group-list password xxxxxxxWebVPN
internal MJHIvpn group strategy
attributes of Group Policy MJHIvpn
value of server WINS 10.0.10.1 10.0.10.2
value of 10.0.10.1 DNS server 10.0.10.2
allow password-storage
Split-tunnel-policy tunnelall
mjhi.local value by default-field
allow to NEMusername field-3002 SjfS1Pq2xZGxHicx encrypted password
attributes of username field-3002
VPN-access-hour no
VPN - 250 simultaneous connections
VPN-idle-timeout no
VPN-session-timeout no
Protocol-tunnel-VPN IPSec
allow password-storage
type of remote access serviceremote access to field tunnel-group type
General-field tunnel-group attributes
Group Policy - by default-MJHIvpnIPSec-attributes of tunnel-group field
pre-shared-key *.class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the they
inspect the icmp
!
global service-policy global_policyHello Ala,
In Act got to be with the Nat configuration.
So basically you want to tunnel the traffic on the rays to communicate with each other.
OK, it would be with a nat 0 with the access list with the corresponding traffic outside.
Also on the crypto ACL for each site configuration, you must add an entry for the traffic of other offices.
I hope that I have explained myself.
Have a good
Julio
Note all useful posts!
-
Hello. I would make both objects or images imported into Muse react with each other. When I say react, think of a ball bouncing off a wall or a pool ball hitting a bunch of other billiard balls. I searched for a widget that might allow cela and couldn't find one. Is this something that can do Muse, or should I look for something else... edge or the interaction of coding? Thank you.
You can do using the edge, then publish it in the "animated dashboard deployment package", ".oam".
-
I want to create a Web site with 4 child pages that interact with each other when opened separately on 4 different computers.Is this possible?
Example:
Child 3-page Web site open on 3 different computers with triggers and the following objectives:
PC #1 - child #1 - confirm button (trigger)
PC #2 - Page #2 - accepted Confirmation Popup, resulting by clicking on 'confirm' page computer/child #1 (target)
PC #3 - child Page #3 - calendar Popup changed, resulting by clicking on 'confirm' page computer/child #1 (target)
Any ideas are much appreciated.
THX.
No this is not possible with Muse.
-
How to install VMplayer 3 network for virtual machines to comminicate with each other?
People,
Hello. I use VMPlayer 3.
SE host: Windows 7
Comments to: Windows XP and Oracle Linux 5I need to set up the network and activate Windows XP communicate with Oracle Linux 5.
I followed this tutorial http://www.vmware.com/support/ws5/doc/ws_devices_serial_2vms.html to configure 2 virtual machines in Windows 7 host machine.
I tried to test 2 virtual machines in the way as below:
In Linux, [user@localhost ~] $ping WindowsXP_HostName
Release: Unknown host WindowsXP_HostName
At the Windows XP command prompt:
C:\ping localhost.localdomain
Its release: ping localhost 127.0.0.1 with 32 bytes of data...
Reply from 127.0.0.1: bytes = 32 time = 2ms TTL = 128
He meets a few times and then disconnected by itself. It seems that Windows XP is ping itself and not Linux server. The host name of the Linux server is 'localhost' as well. It is a kind of confusion for me.
From the information above, we can see that 2 VMs cannot connect between them.Can any folk provides a tutorial or example or case study to set VMPlayer 3 allowing 2 virtual machines communicate with each other by step?
Very grateful in advance.
In the guest machine, all I see is click on VMplayer-> VM-> settings-> network-> Network adapter Connection-> select Bridged: directly connected to the physical network. After that, nothing to keep.
That's it for the network card in Virtual Machine of its parameters, and the rest is done to each guest at the guest OS level.
In Windows 7 host machine, I don't see anything first.
What we need to do is to assign 3 IP addresses to 3 machines: Win 7, Win XP Guest and Linux host.
Why the world can't bring you up Google in a browser and type, the ip static windows xp, then static ip rhea of windows 7 and finally static ip. As I have already said there are more then enough tutorials on the Internet about how to configure a static IP address by a given operating system then I suggest you Google it! It makes absolutely no sense to write the instructions step by step for you when there are already dozens of tutorials available on the internet.
-
Hello ~
This question has probably asked a million times in a way or another, but here's my specific: I'm a laboratory for school. I've set up two virtual servers (Windows Server 2012) in VMware Pro 12. The goal is to speak (see others). According to the instructions of the teacher, I set them up as follows:
"Assign your appropriate servers of IP addresses based on your installation environment. For example, if your network environment uses the class C address range 192.168.1.x, assign a server IP 192.168.1.10, 255.255.255.0 subnet mask, a default gateway 192.168.1.1 and the other server IP 192.168.1.11, 255.255.255.0 subnet mask, a default gateway 192.168.1.1. Note: If these IP addresses will conflict with your internal network (provide your virtual machines with access to the internet), please choose a different set of address that will work for you. »I need to know what will work addresses. got a domain controller DC1. Now, I can't see each other. I can't connect to Internet via IE which is one of the 'evidence' that I'm supposed to provide.
When I go to the Publisher, I see as the guest only parameter (how is it said to set up when you first install the VMs) is 198.162.150.0. I did not who, but I'm a little but I don't want to make things worse by changing things. I guess that's where the problem is, but I'm not sure what to put the IP, default subset mask and DNS for so I'm stuck.
If it means anything, it is in fact on a borrowed laptop which is connected to the WiFi and wireless. The laptop has internet but I don't know how exactly bringing on the virtual machine when it come to be able to connect. I don't need to become an admin system; This is a compulsory course and I'm just trying to understand enough about it to pass. The problem is that other labs are constructed on it so I can't just ignore it.
Any advice you can offer would be GREATLY appreciated. By the way, happy new year to you all.Sorry, yes it was a typo. It's supposed to be 192.168.150.xxx.
Although the virtual machine must be able to communicate if they are both configured similarly (i.e. host only in this case), you generally EF IP addresses in the subnet host only for those virtual machines to be able to access it from the host, which - as mentioned earlier - should have an address of VMnet1 IP of 192.168.150.1.
André
-
two PID.vi effect each other or not in the same program?
Hello!
I know that the PID.vi can be used in a multi-channel manner, and controls of this case different PID do not distrube each other. What if I use the same loop PID.vi two s to control two independent processes? They will be the effect each other? I want them to work independently, how can I handle this?
Thank you!
If they are reentrant, each instance in the schema will work independently and is want you want. No changes are necessary.
(Do not change system screws or things will break up with the next update of the software )
Maybe you are looking for
-
Our photos were in iPhoto and Aperture until the upgrade to El Capitan. Photo and the opening are now gone. Is it possible to include both of these libraries in Photos of El Capitan? (When I added the second library of Photos, the first library di
-
10.11.3 - cannot start iMac with monitor external thunderbolt
Updated 10.11.3 yesterday evening. New problem I've ever seen. iMac (late 2015 version, with 27 "screen Retina 5 K, Core I6, SSD, Radeon R9, 16 GB of memory). connects via a thunderbolt cable to Apple 27 "monitor Thunderbolt, model A1407 (so I see t
-
VI 'Variant to data' Converts the DateTime inaccurate.
The extracted data is a timestamp column in a microsoft access 2007 database. As shown below, the said Variant ' 1: 46:45 '. But the timestamp converted from Variant 1 milliseconds before the Variant. It is now "1:46:44.999". He is shown below. How c
-
I need help to find my incoming and outgoing server address are
I am trying to set up my email and asked what my incoming and outgoing servers are how will I know
-
Edge of blackBerry Smartphones and UMA signal does not
Over the few weeks I noticed that my phone is stuck on the GPRS network all the time and find EDGE or UMA - I can find my house through the wireless section hub but can not connect to it - sometimes with the connection completed and now in the last d