U3014 problems

Similar Questions

• U3014; problems to get maximum performance via HDMI

  I just got my U3014 delivered, but I meet a lot of problems run.

  My first test was with my MSI GT780DXR system windows 7 64 (nVidia GeForce GTX 570 M). The laptop only has VGA and HDMI 1.4, but HDMI should be able to 2560 x 1600 @ 32 bit. But the nNvidia guard device driver complain that the U3014 cannot do. The highest I could get is 1920 x 1080. After a configuration custom in the nVidia settings, I run it on 2560 x 1600 @ 16 bit / 60 Hz. But on a large 16-bit screen doesn't sound like a lot (to say the least).

  So I plugged on my desktop also W7 64 bit (nVidia GeForce GTX 560) and she went immediately to 2560 x 1600 @ 32 bit (60 Hz). So I know this works (in is superb).

  A third trial involve a laptop HP with Ubuntu and a DisplayPort. It takes too only 1920 x 1080.

  I'm starting to suspect that HDMI 1.4 set in place in the U3014 is not able to 2560 x 1600 @ 32 bit / 60 Hz as the HDMI should be.

  I used a standard HDMI cable. Then I entered the Nvidia tool and created a custom resolution (because the monitor does not list what he can do on HDMI). Not all parameters of work, but that does not work is:
  -2560 x 1600, 60 Hz, 16-bit
  -2560 x 1600, 32 bit, 24 Hz
  -2560 x 1600, 32 bit, 36 Hz MacBook Pro retina

  I do not see a flick @24 Hz so I leave that for the moment. According to the 1.3 specification, it should be able to do little 24 or 30 to 60 Hz and 1.4 even more. But I can't configure that. I need that pick up with Nvidia.

• U3014 + PS3. Problem with the display resolution?

  Hello!

  PS3 cannot expose to a resolution of the screen for Dell U3014. I use the HDMI-HDMI cable. In the attempt of a choice display resolution in the settings of the PS3 when it test the monitor may not issue image. This means that an installer of the screen may not be complete. Now the installation of the screen program gives 576 p. As you understand, it is impossible to play on it. Please help with a problem.

  Thank you.

  Niko7,

  The U3014 HDMI port can do 1920 x 1080 (1080 p).
  * With the monitor and the PS3 on and using a HDMI to HDMI (not a DVI to HDMI) cable right, turn off the PS3 via the power switch on the back and then turn back with this same switch
  * Press and hold the power button on the front of the PS3 until you hear 2 beeps. Once it turns on, the screen should display a message something like: "an HDMI cable has been detected, you want to set up?
  * Then go here to set the video output to your TV/monitor
  http://manuals.PlayStation.NET/document/en/PS3/current/settings/videooutput.html
  * When you go through Setup for HDMI setting, you will need to check what your monitor video output modes supported (480i/480 p/576i/576 p/720 p/1080i/1080 p)
  * After you go through the intial setting HDMI menu and displays your PS3 via HDMI cable, on the main menu of the PS3, go to settings and then scroll the display settings. In display settings, put the full range RGB (HDMI) to full and put Y Pb/Cb Pr/Cr super-white (HDMI) on we

• U3014 Vertical lines/artifacts after standby sleep usng DVI - D cable. Work around this problem, use a DP cable.

  Hello

  I have a rev A01 U3014 that works perfectly until recently. Over the weekend, the display exposed vertical lines colored after recovery mode sleep. I cycled the power on the display and the problem disappeared. I thought it was an isolated incident and did not think much. The problem occurs for a few days. Today, the problem has occurred three times - twice taking the sleep and once when I restart. I'm fairly certain that this is not a problem of cable or the video card the problem when I disconnect the DVI - D cable. I have also updated and restored my video drivers, the problem is back, regardless of the version of the driver. I'll also try hooking up via DisplayPort to see if maybe the DVI port is the origin of the problem. If there is no other troubleshooting ideas I can try, please let me know. I have the screen connected to an EVGA GeForce GTX 770, running at the native resolution. Here is a picture of the problem. Yet once again, this ONLY happens when the sleep. I have not seen the problem spontaneously occurring under normal conditions of use. Here a link to the image.

  Just to update this thread - I went the DVI - D cable to a DisplayPort cable to the end of July and did not repeat it problem.  Thus, it seems that the problem was caused by a faulty cable.

• Dell U3014 Rev A01 Scanline problem and translation mistake...

  Hello holy chrism.

  first of all, I'm of the Germany so I have postet several times the problem in the German Forums isuess, but there is no response... I'm here now. I have a dell u3014 rev 1, I have two Points, I have the problem of scanline too and ist there a translation is good ranslated in German as 'aus' error in the menu 'off', but 'we' will not translated in German "auf". the transaltion of right would be 'a '! Maybe you can fix this in the next review? The translation is very annoying error, I bought a very expensive high-end monitor, like the scanline problem. What can I do? Wait until Rev a03 is available and replace it?

  Engineering said that A03 corrected the problems of horizontal lines. As of today (16/08/13), the only way to get the A03 is through an exchange of monitor used/given to nine. It's only for customers in the Americas. Stocks of service for other regions are still undergoing revision A03. No dealers will have A03. The Exchange used/given to nine should be done through Dell. New stock to purchase will not be to A03 until October.

• Problem U3014 don't let it go to Portrait mode

  I just got my replacement screen, unfortunately, it's the same monitor Rev A01 March 2014... Lets see if it works. But in the meantime is there a way to switch this screen in portrait mode? I unscrewed all the screws and it seems there is no way to return the support for portrait mode. Why in the world they wouldn't have this feature?

  Bombadilio,

  Like our U3011, it was not designed to go in portrait mode. The manual and the sales page claim that the U3014 can only tilt and swivel.

• U3014, disconnection of USB 3.0 ports

  I am using a U3014 monitor since April. Early on that USB 3.0 ports would be erratic behavior, i.e. they would disconnect after a few seconds of all copying activity, regardless of their orientation (to distance or download). So every time I have would connect my USB key or an external hard drive, the device will get recognized quickly but any copy operation takes place as soon as the monitor disconnects. It seems not to be able to handle anything larger than 1 MB at a time and significant intervals. Thereafter, the only way to reactivate the ports is to disconnect the cable and then reconnect it. The USB hub is connected to my ultimate T3610 Win7/64 computer with the Dell-supplied cable. The monitor is also connected to a card Radeon R9 270 via the Dell mini provided DP cable. There is another USB device on the monitor, disconnect it does not bring a change in behavior. Same goes for all the different ports USB 3.0 on my computer, that is, any port PC, the monitor connects to. of course, all above 3.0 USB devices work perfectly with the ports on the computer. My monitor is Rev A03 and the S/N CN-0P1V6N-74445-388-172. Any help would be appreciated.

  Thanks in advance.

  If you encounter any problems with your U3014 monitor USB 3.0 ports or disconnecting at random SD card player, it's because the motherboard of your computer Dell T3610 uses an old NEC / Renesas USB 3.0 controller chipset.

  The hub USB 3.0 inside the monitor of U3014 is NOT compatible with the NEC/Renesas USB 3.0 controller chipset. This isn't a problem with the Dell U3014 monitor, there is a problem with the NEC/Renesas USB 3.0 chipset, known to have problems of dropping out.

  To resolve this problem, you must add a USB 3.0 controller card based on the Texas Instruments TUSB7340 chipset inside your computer T3610. This chipset is VERY STABLE. No more random Logout problems with external drives or USB 3.0 flash drives.

  To solve this problem with my U3014 Rev. A05, I installed in my computer the SuperSpeed USB 3.0 PEXUSB3S4 Startech card (built with the Texas Instruments TUSB7340 chipset). I plugged the USB 3.0 cable (supplied with the U3014) and my computer is now very stable.

  The latest drivers from TUSB7340 for Windows 7 controller / 8,1 / 10 are available for download directly from the site of Texas Instruments.

  Either randomly disconnection problems with USB 3.0 external hard drives, flash drives or the SD card reader inside the Dell U3014 monitor with the Startech PEXUSB3S4 SuperSpeed USB 3.0 card.

• Different serial numbers of U3014 monitor on the rear panel and the WMI class

  Hi, I'm doing an inventory of COMPUTER equipment.

  I had a problem with DELL U3014 serial numbers:

  DELL monitors have different serial numbers on the back panel and the class WmiMonitorID.

  For example, there are 20 digits alphanumeric serial number as CZ-0F525M-73608-021-341, on the Panel back and there is the serial number of the alphanumeric number 12, as F525M021341L to the WmiMonitorID class.

  Why is this happening?

  Y at - it an official document that explains this replacement of the serial number?

  I have no problem with the monitors from another manufacturer.
  

  Because the Dell order number is lost, there is no way that you or Dell can prove any guarantee. Without evidence, Dell will only guarantee the monitor for 3 years based on the serial number.  This sounds like infringing material in not usa or EBAY or something other than Dell.

  CZ-0F525M-73608-021-341 L = February 1, 2010 to February 1, 2013 to a U2410

  This number is taken from this forum.

  First 2 letters is country of origin.  MX = Mexico CN = China CZ = Czech Republic etc.

  0F525M is the number of Dell.  It is an IEMEA part number.

  It is not a U3014

  http://www.impactcomputers.com/f525m.html

  The forum is not a guaranteed correspondence Committee.

  The forum is not about service or warranty outside the United States.

  

• Dell u3014 does not connect to any laptop (Dell XPS 13 / Dell Studio XPS 1340) via display port

  Now, I received my u3014 dell monitor last night and did not, as still able to connect to one of my laptops.

  I have a Dell XPS 13 (L321X), which has a port minidisplay outside and a Dell StudioXPS 1340, who was a regular on displayport.

  Dell has included a mini displayport to displayport cable with the monitor and I tried this cable with two laptops, but no video appears.

  I get the following messages with each laptop:

  With the XPS 13: The monitor says "no displayport cable is connected.

  With the Studio XPS 1340: "This monitor now goes in powersafe mode'.

  The monitor works fine via HDMI and DVI, but obviously those who do not allow me to enjoy the maximum resolution.

  The two laptops under windows 7 64-bit with video drivers of dell stock. I'm at a loss for what to do and would appreciate any suggestions/help someone.

  Update: Dell sent me a new, replacement monitor. With this new monitor, I bought two cables:

  Mini-displayport to mini-displayport to connect the XPS 13 to the U3014:

  http://www.MonoPrice.com/products/product.asp?C_ID=102&cp_id=10246&cs_id=1024602&P_ID=5991&SEQ=1&format=2

  regular DisplayPort / regular displayport to connecct Studio XPS 1340 to the U3014:

  http://www.Amazon.com/GP/product/B005H3Q59U/ref=oh_details_o03_s00_i00?ie=UTF8&PSC=1

  results: EVERYTHING WORKS as IT is MUST!

  As soon as I hung the xps 13 on the monitor, the monitor acknowledged instantly and went at full resolution. The same is true when I tried to connect with the Studio XPS 1340.

  So I don't know if it's a simple cable problem or if there is something wrong with the circuit board on the original U3014, and frankly, I don't want to try my new cables with her, just in case, and facing another headache.

  Whatever it is, this fixes all my problems. Thanks for all your help to try to diagnose the problem.

• U3014, A03, low noise level, Nov 2013

  After receiving insurance through Dell Small Business. the U3014 all new have at least Rev A03, I ordered another to replace a fading 3008WFP.  After you received yesterday, I ran through the installation program and checked everything, including the USB3 and operating an internal decoder 2-channel audio.  I use the standard Dell AX510 sound bars on all my monitors to reproduce audio embedded with HDMI signal sources and nVidia Quadro Display Port K5000 than card outputs.  My other Dell, a new U2713H and an old 3008WFP monitors, work very well with their AX510 sound bar.  However, the same inputs HDMI and Display Port on the U3014 produce a less than 13 dB audio output.

  A sound signal to 1/20th of the normal level makes its unusable AX510 with my new monitor U3014 bar.  Since I do HDTV edition, I need to use the U3014 to monitor the video and audio from my reading of BlackMagic Decklink 4 k Ultra HDMI as long as the audio embedded on my nVidia Quadro K5000 video card display Ports.   (BTW: USB3 parts work fine)

  Everyone knows a similar problem of audio low on their screens of U3014?

  This is an update to the original message of low audio output:

  After contacting Dell Small Business Tech Support.  Dell sent me a replacement U3014 monitor via FedEx overnight.  After that I connected to my system and it turned on, I was pleasantly surprised because audio Digital Envoy through the HDMI ports and DP was NORMAL.  In addition, the display of U3014 had no corner visible backlight line, as it is 'normal' for this view.  But the strong "glow" IPS limits how close you work at the screen of the monitor.

  However, after about 30 minutes the audio level fed by the Audio Jack Out U3014 for Dell AX510 went way against.  A different sound bar did NOT help.  When I plugged the Audio Out jacks on my U2713H and U3014 monitors to the audio meters of Sony Sound Forge Pro 10 six channels and I saw the same 13 dB drop in the two channels that the first U3014 suffered.

  

  The two U2713H (audio channels 1 & 2) and the U3014 (channels 3 & 4) were fed the same HDMI DirecTV output. The recorded maximum concentrations are at the right end of the Green level bar poster.   These show the difference between the output taken on two audio monitors.  The output of U3014 is 13 DB below the output of U2713H.   When turned on the U3014 was identical to the U2713H!  After 30 minutes the audio output of U3014 level has dropped.

  My guess is that something in the digital audio receiver has failed.  And, since the two U3014 monitors are close in the serial numbers, this failure is likely to happen all U3014 in the same factory lot.

  Given that most of the users of U3014 is not to monitor the audio digital integrated on the inputs HDMI or DP, there are not too many reports of this problem.  Those who intend to use the U3014 of audio and video surveillance on HDMI or RFP decision taken entry need to check this problem.

  Bill Wood

• Update of the purge U3014 backlight issue?

  Chris,

  I followed the U3014 because it was announced in February and the last point keeps me buying one is the backlight bleed which is seriously worse then the U3011. In this thread: http://en.community.dell.com/support-forums/peripherals/f/3529/t/19513942.aspx you said that the issue has been reassigned to support a few months ago. What is the most updated on the issue? The next revision of monitor (A04) will fix this problem?

  Thank you

  Fix.

• U3014 dim parameter value includes sections twinkle to normal brightness during scrolling?

  I have my U3014 set to a very low (~ 30%) because of where I work. Sometimes, when I am quickly scrolling pages with text on white background, random rectangular sections of the monitor back to max brightness for about 2 seconds before returning to normal which fairly quickly became irritating. First of all, what is this problem? Second, how to fix it (get a new monitor?)?

  Don't forget to test the U3014 if you have enabled EVS (Smart video improve) off the coast.
  * Press the Menu key to open the OSD (On Screen Display) menu
  Open the display settings
  * Improve the intelligent video highlight
  * Change to Off
  Out of the OSD

  You can test the monitor problem on the system without the other two monitors connected to see if the problem persists?

• U3014 monitor hangs, not responding

  Hello

  I bought this camera last week and since I noticed that sometimes the monitor becomes unresponsive (several times a week, sometimes several times a day). Here is what I noticed:

  -Computer saving energy and monitors goes, but this monitor feeds not off but instead goes to the white screen (the other display off fine)
  -After the previous monitor does not display an image after getting out of the power save; again, made another display
  -Sometimes the screen turns off, but does not illuminate

  Common to these events, it's that the menu button (or the other buttons) do not work. The only way to get a reaction is the power button, and even in this case it does not sometimes. However, I noticed that now the button for a few seconds the stop screen always makes. After power cycling the display always comes back fine.

  Sometimes the symbol corresponding to the DVI cable (dual-link DVI-I use for 2560 x 1600 60 Hz) appears to the left upper corner of the screen and stays there. This is similar to the other crashes.

  I used to have a HP ZR24W and a Dell 2412 M connected to the PC with GTS450 (Linux) without any problems earlier. U3014 replaced the HP.

  Any suggestions?

  Finally, the problem has been resolved by replacing the unit with a new one.

• Very big problem with successful professional on-screen color in PS CC and CS6 win7 64-bit

  How to reproduce this problem:

  -Photoshop CS6/CC

  -Win 7 Ultimate 64 bit English with all updates.

  -ATI 7870 / 550 HD and the first graphics cards.

  -Dell U3014, CINTIQ 21UX (in the 7870), 2 samsung 2232 in the 5500 (all about, or one at a time)

  -Spyder 3/4 Elite, Display 2 Eyeone, DispCal (argyll), ColorEyes 1.60

  After calibration and the profile process with everyone from this screen with tools (lets assume that all is well), open an image with colors more saturated (with Adobe 1998 RGB color space) in CS6 or CC and press "F" key to turn on or off screens.

  You may notice that the saturated colors change (will become even more saturated) in the nest two screen modes and colors come back to the 'normal' fi hit F once more.

  Looks Photoshopped to get rid of calibration read in F 2 screens modes and return to normal when the image is in the initial display mode.

  PS: startups of Chargers of each calibration of the screen, chose one of the time when I restart the PC (so that there is no multi Chargers try to put your luts simultaneously)

  -PS CS6 / CC and the WINDOWS are completely up to date

  -Display card driver, are the last AND the windows certified

  -There is no other software installed on the PC that try to manage the map graphic, or even different CMS.

  -Actually Windows are a new installation

  -This RGB and CMYK images.

  It's very frustrating...:)

  Dear Lundberg, in fact I'm wrong on this subject arrive in RGB images, only happen in CMYK (some CMYK) mode

  If you have a Win 7 64 bit PS CS6 or CC update and calibrate your screen with a spectrophotometer, colorimeter and their respective software. Download images like this flowers:

  http://HDW.eweb4.com/out/663221.html

  Before, be sure to set in the PS, this attachad of color settings:

  

  Open this file, convert it to CMYK and press the F key to switch between display modes.
  If you have a calibrated screen, let me say, Eyeone and Coloreyes and the videoLuts charger is on, when you press the 'F', the colors in the CMYK image, will become much more saturated/heavy/dense, so click on the F button until the screen mode is 'normal', the color back to normal too.
  I test this behavior in 8 machines far and in all machines of this, the change in colors are very noticiable to reach a point that I can't be used in color professional work.

  I hope that now I could express my good self.

  Kind regards.

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.