UDP communication via secondary ethernet port on the cRIO-9074 problem.

Similar Questions

• RS232 port on the cRIO-9074

  Hello everyone!

  I have a cRIo-9074, with on the frame a RS232 port. I'm trying to use it, but without success... I have already installed NI-Visa. But what do I do now? When I create a new project, I can't find the serial port, and I can't find a tutorial for this...

  Thank you very much.

  Simon M, starting in Labview and cRIO.

  Hello smichau,

  This problem was already forum dealt with several in is not this one.

  http://forums.NI.com/T5/LabVIEW/cRIO-serial-port/TD-p/1145870

  I wish you a good day,
  Kind regards

• I use a third party inf file when creating a network connection via my USB port. The USB connection will become inadmissible and also cause the laptop hang up.

  I use a third party inf file when creating a network connection via my USB port. The USB connection will become inadmissible and also cause the laptop hang up. Currently I try to modify the INF file but is seeking a help or suggestions in T/S to this problem. Thank you.

  original title: third party INF problems

  Hi Paul,.

  ·         Why are you using a USB port to create a network connection instead of using an Ethernet connection?

  You can see the following article on how to set up a network.

  How to set up a small network with Windows XP Home Edition (PART 1)

• Same code compiled for the cRIO-9074, but reports no diagram component calendar violation for cRIO-9067

  Hi, just got my new cRIO-9067. I have converted my project over the cRIO-9067 since the cRIO 9074. Same layout module, same engine, same scan code custom fpga, (hybrid mode).  I have no problem of compilation for the 9074, which is a lower performance FPGA architecting the 9067 FPGA.

  The final timetable for windows compilation shows that the timing is respected for all clocks - 40, 80 and 120 MHz (I use a clock derived for some code sctl). During the end of compilation, during the phase of gen bitfile, I get the dreaded time violation. Investigation of the breach indicates that it is not the custom code, it is not schema components. One of them seems to be linked to the card series OR 9870 I in the chassis.

  Why? Is there anything I can try with the compiler directives for this problem? You would think that it would be easier to compile for the highest performance FPGAS...

  OK, don't ask me how I thought this output - to run I changed nothing else than this: feed the I/O node a reference FPGA of e/s instead of configure the node via the menu "link to. It makes no sense, but the compilation succeeded when I did this.

  I know it is because I created a very simple test VI in my project and made sure it does not compile without it.

• The computer hangs during the communication via a serial port

  I developed a code in LabVIEW 2011 to connect with the XY stage. It's actually two steps mounted perpendicularly. The installer of the system is that a (made by the same manufacturer as the stadium) gamepad is connected to the USB port on the computer if a USB to Serial converter. A step is daisy chanied to the controller and the other stage Garland at the first stage.

  To our application had to continually check the status and position of the steps X and Y. Because the joystick also returns responses when a request is sent to all devices, I need to send applications individually; for example. one request per order per device, making it a total of 4 orders. It takes care of the error returned by the controller. The problem, however, is that after a while the freezing of the program or the computer stops and restarts. It is located about 13 minutes (on average) after the start of the program. It also happens even when no command is sent to the devices. I put 50 ms delay before each send two commands (position and status) by device. Basically, the application waits for 50ms before sending two commands for X stage and the receipt of the response and when everything is done with X stage, he expects another 50 ms to do the same for step Y. Should this procedure goes on until the application is stopped. But as I said, there is a problem. Now, I guess the problem is that serial port buffer overflows. He chose to increase the delay time, but if it works to solve the problem, then I have no choice!

  I would appreciate any thoughts and comments!

  After a lot of time to experiment, I am convinced that the issue was with adapter Profilic.

• Can workstation make me use the ethernet port on the remote computer?

  Ideal solution would be:

  I have specialized software on my computer I want to use without installing it on the remote computer.

  For now, I have to because the software uses the ethernet computer port to do a job, the software is used to.
  

  
  

  (1) is there a solution out there for everything just to connect to a remote computer and make use of its ethernet port remotely?
  

  
  

  Someone told me that VMWare Workstation last night. Maybe it's completely off-base.

  
  

  If this remote computer is connected to another computer via an Ethernet cable, but not for the internet, only data.

  For me to be able to connect to it, the remote computer must maintain a simultaneous Wifi connection as well.
  

  I use Teamviewer to fight against it.

  
  

  (2) if 1) above is not possible, I'm back to my current setup which is to the software me, I need on that remote computer. But my problem is that it does not seem possible to have WiFi and Ethernet connections at the same time.

  Please correct me / explain how if I'm wrong.

  How can be useful to me in these scenarios Workstation?

  Thanks in advance for your help. I'm looking everywhere for more than a week.

  I read that you wrote in your OP several times and no offense not expected however it is not well presented and I find I have to ask the many requests for clarification, however, I will say this...  A Virtual Machine is presented only a wired Ethernet adapter no matter how the host connects to the LAN/WAN and if you need to wired Ethernet and WiFi Ethernet in the Virtual Machine, and then in addition to the default wired Ethernet you can also provide your own card Ethernet Wi - Fi USB to connect to the virtual machine as well as the two available to the virtual machine at the same time.

  Others while I won't waste time asking a bunch of questions and if you want to take an another stab as describing in explicit and specific in detail what you have and are trying to accomplish, then I add more to the discussion.

• Can I use the lan Ethernet port on the airport express to the release of music?

  Can I use the Ethernet connections on airport express at the exit of music over wifi to a set of speakers? I would use an Ethernet connector at one end a DIN 5 pin to a pair of speakers beolab 2500/2300. I don't want to use the PIN audio output on the Airport express, as it is analog. Possible music out through one of the Ethernet connections at the back of the Airport express? Thank you

  Can I use the Ethernet connections on airport express at the exit of music over wifi to a set of speakers?

  Sorry, but no.

  I don't want to use the PIN audio output on the Airport express, as it is analog

  Perhaps you weren't aware that audio port on the AirPort Express audio book Terminal analog or digital, according to the type of connector used. See this link on the AirPort Express specifications to confirm... http://www.Apple.com/Airport-Express/specs/

  In other words, for the Express deliver audio analog, connect a standard stereo mini plug with connectors appropriate to the other end.  To ensure that the Express deliver audio digital, plug a mini Toslink cable to the audio port on Terminal AirPort Express.  An example is in this link... Airport Express Toslink - Amazon.com

• via a USB port on the guest VM

  Hello

  I will migrate our Blackberry for VMware Server.  We have a lot of servers already there, but the Blackberry server is the only server that we need occationally blackberry via USB as the will of some Blackberry active devices only if physically connected to the server, just do that via the mobile network.

  We have 6 guest VM used one of the USB ports on one of them to serve as a USB port on the virtual server of Blackberry?

  Thank you

  Yes it is possible with vSphere 4.1. Watch the tutorial below:

  http://vStorage.WordPress.com/2010/07/15/USB-passthrough-in-vSphere-4-1/

• How can I connect a Time Capsule directly to my new MacBook Pro? I could connect my old MacBookPro directly via Ethernet cable, but there is no Ethernet port on the new MacBook Pro retina.

  I don't think I can connect wireless because I live in an apartment in a House and the modem and the router are in the main part of the House.

  If it was love at first sight... buy love at first sight for the ethernet card.

• Ethernet port on the question of mac mini 2014?

  Hello I recently returned from a trip, I was away for about an hour and when I got home I turned on my mac mini and BAM without ethernet connection, Ive went through the router and the settings constantly, other computers in the House connect to ethernet, I can connect to wifi with the Mini. When I plug it in ethernet, there is no anything, except for the light on the router on that its plugged in < < < < < < Ive checked the port for obstructions. everything seems peachy from outside, no indication in this regard, Ive reset the router, reset it to factory default, done everything I could think of, checked the DNS settings, I can choose any connection until the router without wifi however. Pls help.. I don't like horrible wifi download features, and I pay a good price for a 100 mb a second connection, which I can only achieve by WAN/LAN

  I have experienced the same problem, undertook diagnostic and eyhernet work in the trunk as im using log out and in my bam account does not work but my wifi only

• Connection cRio 9074 second port ethernet to another device via VISA

  I'm trying to connect a DAQ Yokogawa system to a cRio 9074 via the second ethernet port. I activated the second ethernet port of the cRio with a static IP address on the same subnet as the data acquisition system. I installed the driver NI-VISA and NOR-SERIAL on the cRio. I can compile the code on the cRio and I'm sure that the code works when I connect to the acquisition of data to a PC. I get an error on the open VISA VI.

  Am I missing something or is it not possible to connect the second ethernet port on the cRio in this way?

  Thank you

  Thank you for your response. I found the same information that you provide, but decided to give it a try.

  A few minutes ago, I was able to perform communication between the cRio 2nd access Ethernet DAQ Yokogawa. I managed to do it using the VISA controls. To communicate with the host PC, I get the information of the DAQ with the cRIO as described above and then use shared variables to publish data on the network connected through the first ethernet port.

  If anyone wants to reproduce it just to make sure that the two ethernet ports are configured with IP addresses on different subnets that are configured for TCP communication. If more details are to be simply send me a message.

  Kind regards!

• Using the second ethernet port to connect to the printer?

  Hi I have a Mac Pro 2.1 old school and I'm wondering if I can connect to the network with an ethernet port and connect the latter to a printer?

  If so, how?

  Yosemite running.

  Thank you

  Physically, you use a port and a cable to connect to your network and use the second port and a second cable to connect directly to the printer. The printer must obviously have an interface Ethernet himself.

  However, you need to configure the second port on the Mac and the Ethernet port on the printer for each manually configured the TCP/IP addresses and these should be in a range of different network to your main network.

  If you the main network is something like 192.168.1.1 then your printer and the port on the Mac connection to this need to be in another network, such as 192.168.11.1.

  In theory, if the printer supports Hello aka. mDNS, then maybe you can get away with not having to configure TCP/IP addresses for the connection.

  The main reasons to use a second separate connection as this would be the performance or security, and frankly I don't think that's really relevant here. This would mean that no other computers on your network will be able to access the printer.

• How to extend the network and using the Ethernet port to connect an older computer without wifi capability

  I have a wireless network with my Time Capsule, but also I have an old computer without wifi capability. Is it possible to share the connection to this computer that connects an airport express (model A1264) to extend it and the computer thought that the ethernet port on the Airport express?

  Thank you.

  Yes

• Dynadock U3.0 - cannot use the Ethernet port after update 8.1 Win

  Hello world

  I use a u3.0 dock Dynadock with my Vaio PCS 13.
  I'm not able to use the Ethernet port on the Dynadock since I updated my Windows 8.1 device update 1.
  Before that everything worked well.

  I'm not able to re-install the drivers correctly (tried 7.6m0, 7.5m2). While the game driver tries to start, I get an error message, Setup is not able to put a bunch of registry (SYSTEM\CurrentControlSet\Services\DisplayLinkGA\D evice1) keys (up to 0). (Image 1)

  If I ignore these messages and do not install the driver, the Ethernet port will not installed in Device Manager. (Image 2)

  If I try to install the driver manually (DisplayLink network adapter NCM), I'll get an error message that a driver has been found but that access has been denied. (Image 3)
  I started the safe mode and could install the driver. But if I reboot in normal mode, the machine could not be started.

  I also tried to disable UAC and I am logged on as administrator 'real '.

  Please find the attached messaged (in German) error:

  [picture 1]: http://picload.org/image/lcalwop/toshiba.png
  [Picture 2]: http://picload.org/image/lcalwoc/toshiba2.png
  [Picture 3]: http://picload.org/image/lcalwlg/toshiba3.png

  BTW: If I unzip the Installer (7.6m0) and install * inf for the good Fri & dev (4503) it still does not work...

  I put t know what to do anymore...

  Hello

  After upgrade to 8.1 Windows, you should also update the software/driver Display Link
  This is very important!

  The latest version of the driver can be downloaded here:
  http://www.DisplayLink.com/support/downloads.php

  Note: the old version must be removed!

• Mac Pro does not recognize the Ethernet ports

  After a reboot for my end of 2013 Mac Pro OS x 10.11.3, the two Ethernet ports are most recognized. Suffice to say not 'connected' is one of them.

  I have:

  • rebooted a couple of times
  • Reset the PRAM
  • the power disconnected for several minutes left
  • tried two different terminals
  • tried two different Ethernet cables
  • tried the two Ethernet ports

  The light of the end device will blink.

  WiFi works fine.

  What should I do before I decide that there is a hardware problem?

  Bob

  There was a recent post about the same problem and found a solution. Give it a try: Re-built-in ethernet disappeared.