UDP read too Long timeout, Async Custom Dev fail Shutdown

Hello

I've got a simple custom UDP for VeriStand receiver device that uses a timed loop. She has an infinite timeout so that I can listen on port constantly. I cancel the deployment every time I cause an error: 307730 Error Message: NI Veristand: one or more asynchronous custom devices did not close properly and has been abandoned by the Veristand engine.

Does anyone know how to stop the function Read UDP when it expects a package? What's doing VeriStand when she replaces this behavior, for example he closes the network connection, as the unit cancels? The "Stop.vi" of the device model custom runs?

Similar question for Visa Read with a long time (> 10 s). VeriStand closes the Visa Session? VeriStand just kill the timed loop and leave the rest of the finishing of custom device?

Please note that if I shorten the timeout to 1 s or less the custom device can cancel the deployment without any problem.

Thank you

Brent

Brent,

You should have a way to interrupt your UDP activities to check the system status. Open UDP will create the buffer to the data to be received on this port. As long as reading occurs to clear the buffer before too much data overruns the buffer memory capacity, then you should be fine. Leaving a deadline of waiting-1 loop which blocks it is why VeriStand is having to stop the loop.

You should have a case of time-out period for your operations of UDP/TCP for the periods of low activity in order to check a channel to shut down the device custom.

Tags: NI Products

Similar Questions

  • Cannot transfer Sony e-reader - too long resource

    So far I've never had a problem downloading of books (especially of Waterstones) or transfer them on my Sony PRS-505, but I recently bought a book that looks good in Digital Editions but don't transfer to the player.  The title appears on the drive, but there is only a single page and this shows a page fault.  Under the info point. in Digital Editions, he has a small warning triangle and says "document contains a resource that is too long."  There is a tech note on this on Adobe that has the following:

    Solution

    It is a known Sony limit ® Reader at this time.


    I contacted Waterstones support because I felt that their books are specifically targeted to the Sony reader, they must ensure that this problem arises.  The first response just told me to make sure I had Digital Editions downloaded and when I explained my problem to him once again told me that they were not technically trained for the transfer of Adobe in the eReader and couldn't say more.

    I wonder if someone could tell me if there is anything else I can do.  I love my eReader but I can't read a book on my PC.

    Thanks in advance,

    T

    The situation is quite as much as you have described.  Waterstones bought you an ePub file that cannot be displayed on the Sony Reader.  Waterstones (if you have spent their first level tech support) should be quite aware of the problem, but it is not a problem they can fix as what needs to be done by the editor who created the file.

    You must negotiate with Waterstones, if you want a refund.

    Out of curiosity, what was the title and the Publisher for the file in question?

  • Hyperion EPM services take too long to start

    Hyperion 11.1.2.3

    Windows 2008 R2

    32 GB of memory on each server

    Java 1.6.35

    Server environment four (Foundation/FDMEE, planning, Essbase and SQL server).

    Some how it takes too long to start the services of Hyperion. Using the batch script to start all services. Can someone advise where to start looking. Here's the log of HyS9Planning_SERVER-sysout. If this can give an idea

    < 12 February 2014 12:40:34 hours EST > < Info > < security > < BEA-090905 > < disabling CryptoJ JCE provider auto-intégrité for better startup performance. To allow this control, enter - Dweblogic.security.allowCryptoJDefaultJCEVerification = true >

    < 12 February 2014 12:40:35 hours EST > < Info > < security > < BEA-090906 > < change the default Random Number Generator in RSA CryptoJ of ECDRBG to FIPS186PRNG. To disable this change, specify - Dweblogic.security.allowCryptoJDefaultPRNG = true >

    < 12 February 2014 12:40:35 hours EST > < opinion > < WebLogicServer > < BEA-000395 > < according to the contents of the extensions added at the end of the classpath directory:

    D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\lib\audit-client.jar;D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\lib\css.jar;D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\lib\ctg_custom.jar;D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\lib\ldapbp.jar;D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\lib\opencsv-1.8.jar;D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\lib\registry-api.jar;D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\lib\wlpool.jar>

    < 12 February 2014 12:40:35 hours EST > < Info > < WebLogicServer > < BEA-000377 > < start WebLogic Server with Oracle JRockit (R) Version R28.2.5-50-153520-1.6.0_37-20121220-0844-windows-x86_64 of Oracle Corporation >

    < 12 February 2014 12:41:19 hours EST > < Info > < management > < BEA-141107 > < Version: WebLogic Server 10.3.6.0 Mar 15 08:52:36 PST Nov 2011 1441050 >

    < 12 February 2014 12:41:43 hours EST > < emergency > < management > < BEA-141151 > < Management Server could not be reached at http://hydevf01.uts.mcmaster.ca:7001. >

    < 12 February 2014 12:41:43 hours EST > < Info > < Configuration Management > < BEA-150018 > < this server will be started in mode of managed server independence in the absence of the admin server. >

    < 12 February 2014 12:41:43 hours EST > < opinion > < WebLogicServer > < BEA-000365 > < server status changed initially >

    < 12 February 2014 12:41:43 hours EST > < Info > < WorkManager > < BEA-002900 > < self-adjusting Initializing of thread pool >

    < 12 February 2014 12:41:44 hours EST > < opinion > < LoggingService > < BEA-320400 > < D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\servers\Planning0\logs\Planning0.log log file will be rotated. Reopen the log file if stopped tailings. This can happen on some platforms such as Windows. >

    < 12 February 2014 12:41:44 hours EST > < opinion > < LoggingService > < BEA-320401 > < log file was shot in D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\servers\Planning0\logs\Planning0.log00014. Log messages will continue to be logged in D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\servers\Planning0\logs\Planning0.log. >

    < 12 February 2014 12:41:44 hours EST > < opinion > < Log Management > < BEA-170019 > < D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\servers\Planning0\logs\Planning0.log server log file is opened. All events in the log server-side will be written to this file. >

    OracleFileSSOWalletImpl.getWalletData: enter...

    OracleFileSSOWalletImpl.getWalletData: System.getProperty (user.name) = sp_hydevadm

    OracleFileSSOWalletImpl.getWalletData: dummy sso (shared) file locking...

    OracleFileSSOWalletImpl.getWalletData: locking (shared) file sso...

    Oracle Wallet: Pocket size 12573

    OracleWallet: getSecretStore

    OracleSecretStore: load flow wallet

    OracleSSOKeyStoreImpl: engineLoad

    OracleKeyStoreSpi: Load flow wallet

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: Safe opening 0

    Treatment TP 0

    Storage TP 0 as CN = Entrust .net Secure Server Certification Authority

    TP-1 treatment

    Storage TP 1 as CN = Entrust .net Secure Server Certification Authority 1

    Treatment of TP 2

    TP 2 storing as authority of Certification CN = Entrust .net (2048)

    Treatment TP 3

    Storage of TP 3 in CN = GTE CyberTrust Global Root

    TP 4 of treatment

    TP 4 storing as OU = Secure Server Certification Authority

    Treatment TP 5

    TP 5 storing as UO = class public primary Certification Authority 1

    Treatment TP 6

    TP 6 by storing like UO = class public primary Certification Authority 2

    TP treatment 7

    TP 7 by storing like UO = class public primary Certification Authority 3

    OracleKeyStoreSpi: Storage Secret0

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret1

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret2

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret3

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage of Secret4

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret5

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret6

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret7

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Keystore loaded

    OracleWallet: getSecretStore

    OracleFileSSOWalletImpl.getWalletData: enter...

    OracleFileSSOWalletImpl.getWalletData: System.getProperty (user.name) = sp_hydevadm

    OracleFileSSOWalletImpl.getWalletData: dummy sso (shared) file locking...

    OracleFileSSOWalletImpl.getWalletData: locking (shared) file sso...

    Oracle Wallet: Pocket size 3941

    OracleWallet: getSecretStore

    OracleSecretStore: load flow wallet

    OracleSSOKeyStoreImpl: engineLoad

    OracleKeyStoreSpi: Load flow wallet

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: found cert bag

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: found secret store bag

    OracleKeyStoreSpi: Safe opening 0

    OracleKeyStoreSpi: Safe opening 0

    Treatment TP 0

    Storing TP 0 as UO = class public primary Certification Authority 1

    TP-1 treatment

    Storage of TP 1 in CN = GTE CyberTrust Global Root

    Treatment of TP 2

    TP 2 by storing like UO = class public primary Certification Authority 2

    Treatment TP 3

    TP 3 by storing like UO = class public primary Certification Authority 3

    OracleKeyStoreSpi: Storage Secret0

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret1

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret2

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Storage Secret3

    Get the sequence of bag

    Get the alias of sequence

    Get the secret of the sequence

    OracleKeyStoreSpi: Keystore loaded

    OracleWallet: getSecretStore

    < 12 February 2014 12:42:11 hours EST > < opinion > < security > < BEA-090082 > < security initialization using security realm myrealm. >

    < 12 February 2014 12:42:55 hours EST > < WARNING > < JTA > < BEA-110503 > < migration tool (the AdminServer for JTA manual migration policy, or the captain Singleton for automatic migration JTA strategy) is not available. Jump JTA TRS restoration because isStrictOwnershipCheck is [false]. This may cause corruption of potential TLOG if TRS of Planning0 has been migrated to the backup server and the backup server accesses the TLOG of Planning0. More security can be achieved by setting isStrictOwnershipCheck [true]. >

    < 12 February 2014 12:42:56 hours EST > < opinion > < LoggingService > < BEA-320400 > < D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\servers\Planning0\logs\access.log log file will be rotated. Reopen the log file if stopped tailings. This can happen on some platforms such as Windows. >

    < 12 February 2014 12:42:56 hours EST > < opinion > < LoggingService > < BEA-320401 > < log file was shot in D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\servers\Planning0\logs\access.log00030. Log messages will continue to be logged in D:\u01\Oracle\Middleware\user_projects\domains\EPMSystemHYDEV\servers\Planning0\logs\access.log. >

    < 12 February 2014 12:43:01 hours EST > < WARNING > < oracle.dms.jrockit.jfr > < DMS-58041 > < The JRockit FlightRecorder class declares that it is not active and so the DMS cannot use it. >

    < 12 February 2014 12:44:01 hours EST > < opinion > < WebLogicServer > < BEA-000365 > < server changed to STANDBY status >

    < 12 February 2014 12:44:01 hours EST > < opinion > < WebLogicServer > < BEA-000365 > < server status changed initially >

    Using the OraclePKI provider

    taken javax.net.ssl.TrustManagerFactory supported

    taken javax.net.ssl.KeyManagerFactory supported

    Using the OracleJSSE103 provider

    < 12 February 2014 12:47:37 hours EST > < WARNING > < security > < BEA-090668 > < ignored the role 'Admin' resource deployment ' type = < url >, application is DMS Application #11.1.1.1.0, contextPath = / dms, uri = / ">".

    < 12 February 2014 12:51:03 hours EST > < WARNING > < oracle.adfinternal.view.faces.partition.FeatureUtils > < ADF_FACES-30130 > < without taking into account the dependence of the feature on the function "AdfDvtCommon".  There is no such feature. >

    ATTENTION: From post-deployment of ADF library jar on WebLogic Server. "Provider-lazy-inited" init-param missing LibraryFilter? Ignore this warning if the ADFJspResourceProvider is not used.

    On the road: ADF library non-ADFJspResourceProvider after deployment

    Finishing: ADF library non-ADFJspResourceProvider after deployment (millis): 16

    null

    < 12 February 2014 12:51:17 hours EST > < opinion > < Cluster > < BEA-000197 > < listening for cluster communications using unicast cluster messaging >

    < 12 February 2014 12:51:17 hours EST > < opinion > < Cluster > < BEA-000133 > < waiting to synchronize with other members in the planning stages. >

    < 12 February 2014 12:51:22 hours EST > < WARNING > < Log Management > < BEA-170011 > < The LogBroadcaster on this server has no messages to the server admin log. The server administrator can not run. Emissions of message to the administrator of the server will be disabled. >

    < 12 February 2014 12:51:48 hours EST > < opinion > < WebLogicServer > < BEA-000365 > < server status changed to ADMIN >

    < 12 February 2014 12:51:48 hours EST > < opinion > < WebLogicServer > < BEA-000365 > < Server State has changed for RESUMING >

    < 12 February 2014 12:52:24 hours EST > < opinion > < Cluster > < BEA-000162 > < "async" replication service to start with remote cluster address "null" >

    < 12 February 2014 12:52:24 hours EST > < opinion > < Server > < BEA-002613 > < Channel "Default" is now listening on 172.26.55.119:8300 for protocols iiop, t3, CLUSTER-STREAM, ldap, snmp, http. >

    < 12 February 2014 12:52:24 hours EST > < opinion > < Server > < BEA-002613 > < Channel "Default [2]" is now listening on fe80:0:0:0:0:100:7f:fffe:8300 for protocols iiop, t3, CLUSTER-STREAM, ldap, snmp, http. >

    < 12 February 2014 12:52:24 hours EST > < opinion > < Server > < BEA-002613 > < channel 'by default [5]' now listen on 0:0:0:0:0:0:0:1:8300 for protocols iiop, t3, CLUSTER-STREAM, ldap, snmp, http. >

    < 12 February 2014 12:52:24 hours EST > < opinion > < Server > < BEA-002613 > < Channel "Default [4]" now listen on 127.0.0.1:8300 for protocols iiop, t3, CLUSTER-STREAM, ldap, snmp, http. >

    < 12 February 2014 12:52:24 hours EST > < opinion > < Server > < BEA-002613 > < Channel "[1] by default ' is now listening on fe80:0:0:0:385e:468:a776:2aac:8300 for protocols iiop, t3, CLUSTER-STREAM, ldap, snmp, http. >

    < 12 February 2014 12:52:24 hours EST > < opinion > < Server > < BEA-002613 > < Channel "Default [3]" is now listening on fe80:0:0:0:0:5efe:ac1a:3777:8300 for protocols iiop, t3, CLUSTER-STREAM, ldap, snmp, http. >

    < 12 February 2014 12:52:24 hours EST > < WARNING > < Server > < BEA-002611 > < Hostname "HYDEVP01.uts.mcmaster.ca", corresponds to multiple IP addresses: 172.26.55.119, fe80:0:0:0:385e:468:a776:2aac % 14 >

    < 12 February 2014 12:52:24 hours EST > < opinion > < WebLogicServer > < BEA-000358 > < started WebLogic independent server managed by "Planning0" for the domain "EPMSystemHYDEV" running in Production Mode >

    < 12 February 2014 12:52:24 hours EST > < WARNING > < JMX > < BEA-149510 > < could not establish connectivity JMX with the Administration Server AdminServer to < JMXServiceURL:null >. >

    < 12 February 2014 12:52:39 hours EST > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,430 for the configured timeout of 5 seconds >

    < 12 February 2014 12:52:39 hours EST > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,427 for the configured timeout of 5 seconds >

    < 12 February 2014 12:52:39 hours EST > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,429 for the configured timeout of 5 seconds >

    < 12 February 2014 12:52:40 hours P.M. > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,428 for the configured timeout of 5 seconds >

    < 12 February 2014 12:52:49 hours EST > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,441 for the configured timeout of 5 seconds >

    < 12 February 2014 12:52:49 hours EST > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,442 for the configured timeout of 5 seconds >

    < 12 February 2014 12:52:49 hours EST > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,443 for the configured timeout of 5 seconds >

    < 12 February 2014 12:52:49 hours EST > < WARNING > < Socket > < BEA-000449 > < socket closure as no data read on 172.26.55.119:52,439 for the configured timeout of 5 seconds >

    Do you still have this problem after restarting the server?

    See you soon

    John

    http://John-Goodwin.blogspot.com/

  • File name too long in Microsoft Excel 2008?

    I have Microsoft Office 2008 for Mac and I'm a big user of Excel.  Often, I receive an error message indicating that the file path that I specify when you create a new file is too long.  I am convinced that earlier versions of Mac OS x did not produce this error, or at least worked better.  I'm 10.11.4, OSX but I suffered with this problem for some time.  I read other reviews, stating that there may be a limit of 259 characters for the file name and path.

    My question: can someone tell me if this path length limitation has been removed or the less liberalised in the latest version of Excel?  Should an upgrade just to get rid of this nasty problem.

    Thank you...

    You can also post the question in the Microsoft Office for Mac 2016 forum: http://answers.microsoft.com/en-us/mac/forum/macoffice2016?auth=1

  • Deploy the RT too Long of generic IO file path

    So I've been fighting with this configuration and mistakes on deploying code to an embedded target RT.  I have a RT Linux cDAQ-9132 and I found that if my path is too long, it will give strange errors.  Sometimes the error will be on the opening, the project gives 'Generic IO to file' but is the VI opens without error.  And sometimes I see "loaded with errors on the target and was closed" on the deployment.

    The path to the code reuse in the user.lib is similar to the following:

    C:\Program Files (x 86) \National Instruments\LabVIEW 2015\user.lib\_xxxxxxx\Automotive Communication\CAN Drivers\Generic PEUT Drivers\CAN Class\Public\Signal Conversion\Read signals Polymorphics\Read - Single Sample_xxxxxxx.vi

    Who are 233 characters including slashes and semicolons that falls within the limitation of 260 Windows (or 255).

    An example of this is attached.  Unzip the user.lib zip in the user.lib and open the Test of RT project.  It's a RT. target but open just the RT Test VI.vi should show the generic IO file error and the VI appears missing on BD.  If you then open the signals of read - only Sample_xxxxxxx.vi the VI loads without error and high level VI can be executed without error now.

    I've not seen it documented anywhere, but is there a limit to the length of file that causes this problem?  Is there a document indicating how deeply in the re-use of user.lib can be?  I know that my ways were becoming a bit long but also noticed Windows length had not been exceeded again.  And is it possible that if this limtiation exists, that we will have a little more useful error?  Thank you.

    Windows 7 x 64, 32-bit LabVIEW 2015.


  • Cannot open the folder. No error message. Name too long?

    1. I'm not be able to open a file of some
    2 nor can I rename, see its properties, etc.. When I right click on it, all of these options are missing. Only "open, explore, search,...) But even that didn't work.
    3 - the folder is created by a download manager (eMusic) with the name of music album, where his titles will be saved.
    4. I tried to put its locations in several places (my desktop, my documents, etc.). Won't matter.
    5 - the name of the folder appears to be too long and has special characters:
    Maria zempleni_klara takacs_gyorgy kaplan_jozsef Hormai - Horvath_istvan gati_lajos miller_Kolos kovats_budapest Choir_Hungarian State orchestra_aniko szabo_zsolt Bartha_Ferenc Szekeres P. Madrigal
    6 - when I download an album with a name shorter than his behavior is as expected (can open, rename, right-click on all the options appear...)
    7. as said before, I can't directly delete this folder, but I can delete its parent (and indirectly, the weird folder)
    8 - one thing I've noticed is that if I create a folder in the PC, it will be set by default to 'read only' and uncheck the box even if, he will return to his State 'read only' after the reopening.
    For the love of Christ, what is happening?

    Hello

     
    You can view these methods:
    Method 1.
    Stage I.
    Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
    a. refer to the article below for the procedure safe mode in Windows XP
    A description of the options to start in Windows XP Mode
    http://support.Microsoft.com/kb/315222
    Stage II.
    You need to perform a clean boot to find the program that is causing and then disable or remove. If the computer starts successfully in safe mode and then set the computer to start with clean boot safe mode.
    How to configure Windows XP to start in a "clean boot" State
    http://support.Microsoft.com/kb/310353/en-us
    Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.
     
    Method 2:
    I suggest you make a system full scan just to be sure.
     http://www.Microsoft.com/security/scanner/en-us/default.aspx
    Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
     
  • Press and hold the TAB key too long?

    It is news to me. Customer was an email without realizing that he was now pressed the tab key. He got a pop message indicates that the TAB key has been held down too long. Now, the keyboard no longer works. Whenever we press any key, all we get is a clicking noise. Anyone know what it is or how to reset?

    It is news to me. Customer was an email without realizing that he was now pressed the tab key. He got a pop message indicates that the TAB key has been held down too long. Now, the keyboard no longer works. Whenever we press any key, all we get is a clicking noise. Anyone know what it is or how to reset?

    I'm not sure of the TAB key in particular, but open the Control Panel Accessibility Options and see if the boxes checked.  If so, uncheck the and restart.

  • Downloaded a zipped file/folder would not, the name is too long.

    I have downloaded a compressed file/folder to a trusted site that I always. I unzipped the file (Music mp3) successfully and added to my itunes. When I tried to drag the file of music on my ipod, itunes shows his location could not be found. I went and checked on the folder I unzipped and all these other files with weird characters appears. It took 145 GB of space in my external hardrive (thank goodess). Now, I can't rename or delete the file or the folder itself. I tried a few removal tools but it did not work or when I try to download, my anti-virus software reports me. I need a way to get rid of the file. The budget is tight, so it would help if it's freeware. OR better yet a way to removed without having to download any software. I tried to delete it in safe mod and BACK. Without success. Tried Unlocker and D something software too.

    Have you tried Unlocker which would have been my first recommendation.  I don't know other programs (especially turned to the long name) free file deletion. If Unlocker doesn't work, or none will remove utilitly in Vista (because Unlocker is better than Vista).

    The commercial product ($19 I think) says that he specifically deletes files whose names are too long. http://www.abtollc.com/Folder-Delete.aspx.  I suspect that this will do the trick, but of course I can't be sure so try there is a risk that it will not solve the problem in spite of spending money on it.

    Your problem with the file may be a permissions problem.  Make sure that you have the permissions of all rights and take possession (and maybe both parent folders).  Don't forget to check the Advnaced properties for special permissions that restrict rights or inherit permissions from parent folders - you may need to remove if you already have all the rights on the main screen.  Here are the procedures:

    To view your permissions, right-click on the file/folder, click Properties, and check the Security tab.  Check the permissions you have by clicking on your user name (or group of users).  Here are the types of permissions, you may have: http://windows.microsoft.com/en-US/windows-vista/What-are-permissions.  You must be an administrator or owner to change the permissions (and sometimes, being an administrator or even an owner is not sufficient - there are ways to block access (even if a smart administrator knows these ways and can move them - but usually should not because they did not have access, usually for a very good reason).)  Here's how to change the permissions of folder under Vista: http://www.online-tech-tips.com/windows-vista/set-file-folder-permissions-vista/.  To add take and the issuance of right of permissions and ownership in the right click menu (which will make it faster to get once it is configured), see the following article: http://www.mydigitallife.info/2009/05/21/take-and-grant-full-control-permissions-and-ownership-in-windows-7-or-vista-right-click-menu/.

    To resolve this problem with folders, appropriating the files or the drive (as an administrator) and give you all the rights.  Right-click on the folder/drive, click Properties, click the Security tab and click on advanced and then click the owner tab.  Click on edit, and then click the name of the person you want to give to the property (you may need to add if it is not there--or maybe yourself). If you want that it applies to subfolders and files in this folder/drive, then check the box to replace the owner of subcontainers and objects, and click OK.  Back and now there is a new owner for files and folders/player who can change the required permissions.  You can change now switched to read-only (even if the main folder indicates that they are always read-only - you can access yourself as the owner).  You can keep them in read-only to other users, customers and administrators even (although they can support themselves and access, if they wish, and it is really not that you can do to stop it except protect the file with a password by using a 3rd party product.)  Here is more information on the ownership of a file or a folder: http://www.vistax64.com/tutorials/67717-take-ownership-file.html.  To add take ownership in the menu of the right click (which will make it faster to get once it is configured), see the following article: http://www.howtogeek.com/howto/windows-vista/add-take-ownership-to-explorer-right-click-menu-in-vista/.

    I have no other suggestions at this point.  What is the EXACT and the full path of this folder?  Depending on where it is, we are able to create a new user profile (treat your as if it is corrupted) and traansfer all data EXCEPT the folder in the new profile.  Then delete the old provile if he leaves despite this file - it might or it might not (I'm not sure).

    To try this http://windows.microsoft.com/en-AU/windows-vista/Fix-a-corrupted-user-profileuse.  If that is the only available Administrator Profile (you need to be an administrator to fix this), enable the Hidden Administrator Account (HAA) using http://www.microsoft.com/communities/newsgroups/en-us/default.aspx?&lang=en&cr=US&guid=&sloc=en-us&dg=microsoft.public.windows.vista.administration_accounts_passwords&p=1&tid=d20f9db4-7b2c-48be-a087-7835dc2a9055&mid=d20f9db4-7b2c-48be-a087-7835dc2a9055.  If you don't remember the password, try nothing because that's probably what you (or seller) did during the installation.  Once that is done, don't forget to disable the HAA to save it in case it is necessary once again and for safety reasons (since people often try to hack into systems using this account).  Do NOT use the HAA as your administrator account because if you lose the only administrator on the system account or it is damaged again, then you're watered.

    You can also try to enter in a command prompt: click on start / all programs / accessories / command prompt and right click on command prompt, and then click Run as administrator.  There Cd type a space and then type the path of the fulll name the folder in question (if it even appears).  Once inside the folder type del *. * and see what happens.  It can give you the same error message, or it can remove. Once the content is deleted type cd, and then type del (yes I know it's long) and enter. This can remove the folder.

    I hope this helps.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • computer Dell laptop under Vista Home Basic are taking too long to wake up from its sleep. __

    computer Dell laptop under Vista Home Basic are taking too long to wake up from its sleep.

    http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

    Read the info on sleep disorders in the tutorial above.

    http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

    Also read this tutorial; as well as the 'related links' at the bottom of the links above.

    See you soon.

    Mick Murphy - Microsoft partner

  • Windows update takes too long to find the updates

    I had just installed a new hard drive on my laptop Dell inspiron N5050. I did a reinstall of system clean of my operating system to windows 7. After that, I started to run windows update to get all the necessary updates that I need to update completely from the computer. He has worked for a very long time with no result. In addition, at least 2 hours. all the settings for windows update is set to the settings recommended. but for some reason, in my view, takes too long to get updates. can someone help me please this possible issue

    Hello Darrin,

    Thanks for posting your query on the Microsoft Community.

    According to the description, the Windows updates take a long time to find the updates.

    I suggest to follow the methods below and check if that helps.

    Method 1: If your computer is experiencing problems find and install updates of the operating system, try using the troubleshooter.to of update of Windows the problem fix. He makes sure your computer is connected to the Internet and checks to see if your network card and Windows Update services are running properly.

    Reference:

    Open the Windows Update troubleshooting tool

    If the problem persists, try Method 2,

    Method 2: run the clean boot: Place your system in the clean boot state helps determine if third-party applications or startup items are causing the problem. Check this question in the clean boot state.

    Reference: How to perform a clean boot in Windows

    http://support.Microsoft.com/kb/929135

     

    Note: After the boot minimum troubleshooting step, read the sections "How to reset the computer to start as usual after a clean boot troubleshooting" in the link provided to return the computer to a Normal startup mode.

    See also:

    Problems with installing updates

    Hope this information is useful. Let us know if you need more help, we will be happy to help you.

  • Problem too Long way destination - Item not found to rename folders

    I searched an answer in the world to this question and it seems that none of the '' correction '' that people have had success with worked for me, so I write my own question in the hope that someone can help me, and in turn anyone who stumbles on this problem will find this thread and be helped as well.

    My OS is Windows 7 Home Premium SP1

    Here's the problem:
    For a few months now, I was not able to make a new folder and rename it with windows Explorer (I have to go to the command prompt and do it this way)
    It gave me errors "Destination path too Long", despite the path doesn't exceed NOT the limit of 260 characters. Even if I rename the folder '1' or 'a' it gives the error. I have files that were created before the problem that are fine, but they can't really be renamed with windows Explorer.

    It also gives me the 'path of destination too long' error when you move files in other folders, thus making the Organization of difficult cases.

    I tried to uninstall the update "kb980408" as other threads have said... and it did nothing for me. I tried to delete the reg files as indicated on multiple threads to try to solve the problem that some people had success with... I have not the case.

    I ran chkdsk, several malware scans and viruses which did nothing.

    I had not initially installed SP1, so I tried to see if it changed anything. He did. Instead of the "destination path too long" error, I then go "object not found" when you try to rename a file or move a folder to another folder. If I hit "try again" on this box, then it would actually rename the folder or move the folder successfully. Well, not being able to live with the stupid error that appears when I want to simply create and rename a folder, I searched for a way to get rid of THIS problem that brought me to remove these registry keys once more. After reboot, back to the error "destination path too long" and not rename/move the files once more.

    Anyone had any experience with this problem and you can guide me in a solution that does not involve a clean install?

    Hello

    Read the following article, it helped me to solve the problem.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-files/destination-path-too-long/7ff8d0d0-84F3-4d13-B2FD-f742a38731c5

    http://social.technet.Microsoft.com/forums/en/w7itprogeneral/thread/c6bf8dad-eb04-4818-Ab19-6c46854dd146

    http://www.bryantwebconsulting.com/blog/index.cfm/2012/1/19/getting-around-Windows-7-destination-path-too-long-error-when-deleting-files

    http://forums.techguy.org/Windows-7/911476-solved-destination-path-too-long.html

    Make sure you try all the steps.

  • Too long file names

    I searched this but have not found exactly the same problem

    I'm on a laptop with Windows 7.

    Recently, we changed our server to be online only.

    This means that all of our readers are now thanks to dropbox or something similar.

    A disc remained in my reader list.

    Initially, I had access to this hard drive, but could not edit the files and folders inside.

    Look, but don't touch.

    When the car started all the information on this drive was transferred to online readers AND an external hard drive.

    Which was not noticed immediately, was that some 150 file names were too long for each transfer.

    I still have access to these files.

    But when I try to open or to copy the files from the windows Explorer, it blocks.

    I tried to copy and paste, line of cmd, and several smart programs and I can't seem to get these files to copy, or even move.

    Copy / paste comes up with the error too long file name.

    I can however copy about 2 GB for other files without problem.

    The name of the file is certainly the question that all other files and folders can be copied to another drive.

    On the copy of the disc it comes up with the file name too long for these files.

    Any help would be greatly appreciated

    This issue is beyond the scope of this site and must be placed on Technet or MSDN
  • Cannot delete a file in windows 7. Indicates the specified file name is not valid or too long.

    Hello everyone, I'm pretty stuck here. I can't delete a file in windows 7 or any other do with it besides. Says "the specified file name is not valid or too long. It has a funny name [~ t] and no extension. The file type, say "file". The properties are all screwed looking with a mistake on the Security tab, a size of 0 k, is a Windows (c) \Windows\en-US.The other files in this folder appear normal. The computer seems to work very well without any obvious problems. The only problem is my anti-virus reports with a kind of syntax for the file error and indicates it cannot parse this file. I do not. I can't do a thing with it either. Cannot open, rename, move, delete, change passwords, properties, permissions, nothing. It may be necessary for a good part with 0kb. According to me, I want to just delete the thing. Please, anyone? Thanks in advance.

    Hey bud, I figured out how fix it earlier. I am so happy. I came to remember a command called chkdsk which worked very well for various issues, that I had since the construction of my old 2000 Professional machine. I think that one was my first NTFS system. I always liked how well he error correction. Seemed a lot better than the old scandisk. Low and behold, I tried and star ANISE, it is went through it, found this file almost from the beginning of the analysis and a few lines later, he said has been removed. Says something about the file being orphaned some time ago. It was a very bad child, that I tell you. I ran it in safe mode command prompt. I guess he would have done the same thing in the normal windows well, but I happened to be in safemode, when it came to me. I used the switch /f with her. Since the C:\ command prompt or any drive letter your operating system is selected, type CHKDSK/F if I remember although the f was to have it automatically CORRECT errors. I hope this info helps others with their file or disk problems. It seems that many people say they get mistakes and cannot delete various files here in these forums. Thanks Sandeep for answering me and try to help. It does not matter whether or not it was the fix, it takes time to post and your helping people learn to be it. The only thing that remains unanswered for me is actually the thing of the answer. I mean I can't say someone at - it really answered my question and do not count me? Maybe I should mark so that people will bother to read it and get the fix. HMMMM... I come back here some time later and see whats up.  SeeYou, EWOO

  • "Unable to configure windows update, changes the way back" takes too long...

    My PC just newly formatted and now I can see a problem when I turn it off, he just starts to day and after that it fails... I'm worried about what it takes too long... from 10:00 until 16:00? I read an article on them, she'll just take up to 20-30 minutes, but watch?

    Is there something I can do? Can normally on my return from PC? or what I need to reformat?

    Hi Andrei,

    Thanks for posting your query in Microsoft Community.

    I understand your concern, and we as a community will try to help you in the best possible way we can.

    Here are solutions to some common problems with installing updates. You might be able to fix some problems automatically by running the Windows Update Troubleshooter.

    I suggest you check out the link below and check if it helps.

    "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates

    https://support.Microsoft.com/en-us/KB/949358

    Hope the information helps, if you have any additional questions, feel free to post. We are here to help you.

    Kind regards

    Guru Kiran

  • Pointer is over an icon too long. It is not easy even get the internet sometimes

    I find it too difficult to navigate. Need me to places just because my pointer is over an icon too long. It is not easy even get the internet sometimes. I'm the only person who dislikes this 'new' windows?

    Hello

    These should help:

    Ways to improve the performance of your PC
    http://Windows.Microsoft.com/en-us/Windows-8/improve-PC-performance

    Maintenance & performance
    http://Windows.Microsoft.com/en-us/Windows/performance-maintenance-help#performance-maintenance-help=Windows-8&V2H=win7tab1&V3H=winvistatab1

    Crashes Windows or freezes
    http://support.Microsoft.com/kb/2681286

    =======================================================

    You use a 3rd party antivirus/antispyware/security program? If so many people
    can cause slow start from the bottom.

    Check with the support of the system Maker (manufacturer of motherboard for customized systems), their
    online resources and the drivers and ask questions in the forums about known problems.
    Updating the BIOS , drivers of low level chipset and embedded and separate major
    device drivers
    (anyone who can have an impact on the speed of startup and performance).

    Note the use of Win Key + X and Win Key + W (to go on the Control Panel, Run and parameters
    According to needs). Win + D key calls the office and using Win Key active / disable the office and
    Splash screen.

    Check startup programs.

    Right-click in the left lower corner - Manager of tasks
    Or Windows key + X - Manager of tasks
    Or right click on the taskbar - task manager

    Check the Startup tab.

    More troubleshooting:

    How to perform a clean boot for a problem in Windows Vista, Windows 7,
    or Windows 8
    http://support.Microsoft.com/kb/929135

    Other programs to help:

    Autoruns - free - see what programs are configured to start automatically
    When your system boots and you connect. Autoruns also shows you the complete list
    locations of registry and files where applications can configure start automatic settings.
    http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
    Process Explorer - free - find out what files, registry keys, and other objects
    processes have open, which DLLs they have loaded and more. This unique
    powerful utility will show you even owned by each process.
    http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

    =======================================================

    If necessary:

    Try to do a "Refresh your PC without affecting your files" (or modification of your personal data
    settings) or even a restore. Be prepared to re - install the programs, applications will remain.
    And having redundant backups of your files on the disk main hard is always a
    good idea.

    Windows 8 includes special discount methods (keep files and settings) or a reset
    (new installation remove all).

    How to restore, refresh or reset your PC
    http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

    How to create a system image to refresh your PC in Windows 8
    http://support.Microsoft.com/kb/2748351

    How to update Windows 8
    http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

    How to reset Windows 8
    http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

    If you need a repair disc:

    Create a system repair disc
    http://Windows.Microsoft.com/en-us/Windows7/create-a-system-repair-disc

    How to create a "system repair disc" (CD/DVD) in Windows 8
    http://www.eightforums.com/tutorials/2855-system-repair-disc-create-Windows-8-a.html

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

Maybe you are looking for

  • Why my headers in Spanish after running a virus program and how to fix it?

    I ran a free program AVG yesterday and spent a lot of my things in Chrome which I don't use. Then, the program has disappeared. Today Windows anti-virus program pops up and ran full scan and now Fire Fox headers are in Spanish. More he put me back in

  • Very slow startup MacBook Pro

    Early 2011 MacBook Pro 8.2-2.3 GHz, Intel Core i7 X10.9.5 of OS running Starting last very long. Spinning last icon for about 10 minutes then the Apple icon is anther 10 minutes or more. Everything from here looks very good, but it makes me nervous.

  • 8 window

    Dear Sirs, My HP TouchSmart 610-1188D desktop PC, which installed with window 7, Prod. # QP237AA, serial number {removed privacy}, now I think that if I change the window update 8, she is taken in charge or not? Thank you, best regards. [Personal inf

  • ID of the parts for my laptop G7-2240us

    I need to know who is the real author of the motherboard on my laptop 2240us G7 is, if I use a program of IDENTIFYING these pieces, it is said that it is a HP motherboard so what I need is the genuine manufacturer and the model of this motherboard.

  • Windows 8.1 remove with the recovery tool, can I get it back

    Hello I have HP ENVY 15-j101ex NB I installed UBUNTU and all hard disk delete, to restore the Windows OS 8.1 and how? The laptop still on warranty Thank you