UMI-7764 second axis does not

I have a strange problem with my installation of motion control OR and I was wondering if someone could help me.

I have the following configuration:

PCI-7330 connected to an UMI-7764

Connected to the UMI-7764 I have two drives of P70530 stepper, themselves connected to two engines step by step from Nema-23 with encoders tree wired to the UMI-7764. While following the manual.

The switch "Inhibit the entry" is set to active top and switch "Output Inhibit" is set to active low.

The two discs P70530 initialize (solid green LED). The step by step and the engine performs on the terminals of the 'axis 1' of the UMI-7764 works very well. The other, performs on the terminals 'axis 2' does not work. When I try to run a query through MAX, the engine hear "click" once and then disengages. The reader is then a flashing green LED.

The engine will stay disengaged until I try a movement in the opposite direction, how the same 'click' is heard and the motor is now engaged. No movement other than the vibrations caused by the engine engage/disengage occurs.

Readers and encoders are wired identically in the UMI. I had the cables with the player that works as well as the discs themselves and even engines. The result is always the same; training/cable to 'Axis 1' engine works fine and 'axis 2 ","clicks"but does not move.

I would like some advice or suggestions anyone can provide, please.

After going back through all the threads, once again, I finally finished by checking the list of pins on the P70530 drive - > UMI-7764 cable.

It turns out that I had the wrong cable on the second axis. Part number 198151-2R5 instead of 198141-2R5. D - SUB connectors they are identical but different pinouts. After mapping the pins to the correct UMI axis terminals 2nd screw works now.

Tags: NI Hardware

Similar Questions

  • Why is my second screen does not work - it starts with my main screen, but then turns off.

    My HP Pavilion P7-1120 Desktop PC does not work with two screens - there 8gig of ram...  1.5 terabyt hard drive, Windows 7 64-bit primary system works via the VGA port, but the second screen does not rest via the DVI port.  The two normal startup with the start-up of information on both screens, then the secondary display stops and I get a message "no signal".  Both monitors worked with my laptop PC and older myDell...

    When I go into the control panel and the view tab - the PC does not recognize the second monitor.

    GEO...

    It's not a problem with my PC or whatever it is in the box.  Cables work on other screens of the RGA and DVI.  There is a problem with my screen - the works of port RGA, is not the DVI port.  Another monitor works properly by the DVI.

    Now fixed.

    TKS for the entry.

    GEO...

  • ' Date/Time To seconds' function does not respond to the "split second" entry

    The function "Time in Seconds" (contained in the Function\Programming\Timing - range) does not meet the "split second" entry (see example).

    Hi Reimar,

    as I do not see your example I can only say: it works as expected:

  • RAID-1 failed, the second drive does not start in RAID

    I bought a Dell 531 running Vista with RAID1 set up on two 300 GB drives.

    And that works very well... but then the first disc got a bad place.

    Ideally, I could unplug this drive and run the other player;

    However, the second disc has a RAID boot sector!

    [he has a normal boot sector, so if I plug it into the unused (non-RAID) SATA-3 slot, it will start]

    Should be no problem, just start the recovery DVDs and let Vista install a good start...

    But NO!  The DVD version does not see the drive.  (I tried to load the sataraid drivers, no joy)

    Note: if I have the drive failed in the RAID and the second drive in SATA-3, it starts to SATA-3.

    If I put the two drives on the RAID, it starts on the failed disk.

    Now I have a replacement for the defective drive.

    How to make 'good' initialization as a RAID drive and rebuild the new drive?

    How can I get a boot sector capable of Vista/Raid on the disc?


  • 2.5 AppVolumes second appstack does not show in the BONE

    I have appvolumes deployed, and I created an appstack which has 3 possibilities of use in successfully (chrome, adobe reader and Notepad ++) for testing. I have this set on a non-persistent desktop with the AppVolumes agent installed and it works well. I went back to my VM capture and restored the snapshot, created a new appstack and installed firefox. After completing the capture process, I joined the new appstack to the same VM/user as the original appstack. The new appstack shows no firefox in the virtual machine. It seems that the new appstack VMDK is attached to the virtual machine, but I do not see a shortcut of firefox on the desktop, it does not appear in the program files either. Initially I thought that maybe it had something to do with having mulitple disks attached to the windows 7 x 64 VM. I thought maybe it was a problem of storage controller, but it seems that by default LSI logic SAS controller should take up to 15 HARD drives. This is where my day is over, but I'll be back tomorrow to take a look more, suggestions are welcome.

    Figured it out. We still had the trial installed, license which by default only allows to 1 appstack reach, by user, at the same time. We have installed the real license and it does not work as expected.

  • Pavilion 15 n005TU: second monitor does not

    I have just connected a Samsung (Res 1920 x 1080) monitor to my HP Pavilion laptop (1366 x 768 Res).

    On double, everything works fine. The second screen mirrors the laptop.

    Custom, the only thing that shows on the Samsung is the taskbar and wallpaper desktop (no icons).

    I can move the mouse around the Samsung screen and select programs, changing what is on my laptop screen. But nothing appears or changes to the Samsung screen, it continues just show the desktop wallpaper.

    I put in correspondence of the two resolutions, which does nothing.

    Can anyone help please?

    Hi @RobM1 ,

    Thank you for visiting the Forums HP's Support and welcome. I looked in your question about your HP Pavilion 15 Notebook n005TU and problems with the connection of a monitor. Under your Control Panel control Panel\All Items\Display\Screen resolution you should list as 1 and 2. They need not be listed in several screens to expand these screens. How do you have the monitor connected?

    Here is a documentfor troubleshooting help to connect a second display.

    How do you connect the monitors? What kind of cord?

    I hope this helps.

    Thank you.

  • Why my second button does not work?

    I have a slide with two bearings of image and two buttons. The two buttons are of choice and we have a correct message and the other has a bad message. Unfortunately, the second button, the incorrect one, will not show the bad message. Is there something about two buttons in the same space that makes this not work?

    The two buttons have no action other than to show the correct or incorrect answer. I have a separate button, with the stop at the end of the slide, allowing users to click to the next slide.

    Call me frustrated.

    I'll add my own questions.

    Is the message of CORRECT feedback given to the first button when you click on just his own correct legend (with the incorrect caption for this button unchecked)?

    And you expect the message INCORRECT feedback appears for the second button by doing the opposite of above (turn off the correct feedback and leaving feedback legend Incorrect running)?

    Or captions that are supposed to appear when you click on these two buttons appear only through advanced Actions attached to the event on the success of the two buttons?

  • SIL flashes once every 6 seconds mac does not start

    My mac book pro end 2011 running El capitan (not sure what version of El Captain) short charges a month ago, when my charger is broken... somewhere, I'm the charger at work now (after a month, it was completely empty until about 2-3 days ago), he would not start I can not reset nvram or smc as the mac won't even turn on.

    If without connecting the charger I press the power button or indicator, nothing happens, but if I connect the charger, then press the indictator of costs it market showing no charge as Whiteout pressing me the button power mac continues to try to start the ISL flashes on the left, the fan turns, there is a noise coming from the hard drive the screen is completely black and this is repeated every 6-7 seconds...

    I thought that it was because the battery was completely discharged so I let it charge for 4 hours the first day then for about 6 to 7 hours the second day then topic 2-3 hours on the third day it was yesterday, so I read a tutorial or something online that said to hold comand, shift, option, r, p and the power button at the same time for 10 seconds and then let it, and press the power button Yet once I did this, but nothing happened, it was in the same loop, then I repeated the process without holding shift it wasn't too then I held command, t nothing happens so in desperation I held the power button for about 10 seconds, the fan has started a lot of dust exploded and fun trotted it started normally then I ran a virus scan and a control of being using bit defender, nothing was wrong with the results of bit Defender, I will attach be check the results soon... all the while there was an X mark on the indicator of battery... then I restarted the mac and he returned to its previous state, I've tried everything to run back removed the disc hard cords battery cables and cd drive leads to the Board and tried to boot with various combinations of even (what I did the day I got the charger is working IE the first day, but two trials failed to produce results and my mac is back on the loop and I'm sick using a phone to post my question) , I am not able display the screen shots I ttok the activity monitor and the edition of text file that I saved with being check the results I copied both of them on my phone so that I am able to provide using any other method, I would really appreciate if someone can help me

    I found a way to solve this problem! This is only a temporary fix and it dosent charge the battery, but I can use the mac on AC only when it is plugged so that's how it happened the charger is plugged into the mac and socket is in the same loop as explained above, then when I remove the battery leads to the mother board or logic board do not know who , but one at the top, then the mac tries to start u see the Apple screen and then it turns off back. Then after a few seconds the fan starts and SIL flashes 4-5times and turns off, then starts again now, when I connect the battery cables again once (while the lights flash) now it starts perfectly and without brand X on the battery icon it shows not charging and the task kernel upward a big piece of my ram There is absolutely no free ram, I found the culprit core task and it is a process owned by the root, that it was something like coreutd I have strength that quitting smoking and the RAM is free as usual when I restart I have to go through all these things that I've done to start the first time and this time another process owned by the root with the task of kernel so I stop and ram is normal again every time I restart the ram is completely sold out

  • HP ENVY17 700: Second monitor does not work

    I'm trying to set up a second monitor for my counter top. I have pluged in the vga slot _which for some reason any has a lid screwed on it_ and it works with my computer. It did not work when I turned it on. If anyone can offer a solution asto why this has happened, I'd be happy. Tyler

    Hello

    What is the product/model of your Envy 700 PC series? The VGA port is covered because it won't work because of your machine a DIFFERENT video card. We need to know the product/model of your machine to see what the OTHER video card.

    Kind regards.

  • second monitor does not... Help, please!

    Hello

    Computer: HP Compaq

    Model: CQ2700ED

    Windows 7 Home Premium 7SP1

    I hooked a second monitor (Samsung with VGA connector) DVI-d port.

    I use an adapter from dvi/VGA

    When I turn on the second monitor, he says: "check signal cable".

    In Control Panel / video, he did not see the second monitor.

    What could be wrong?

    Best,

    Rob

    Here are the specifications of your desktop Compaq CQ2700ED. According to the specification, this model has a DVI - D output (digital only) and a VGA (analog only) output as shown below.

    (2) - port VGA port DVI - D (3)-

    There is no liability "adapter" that can be purchased which allows to convert a digital signal to analog. The only way that you will be able to use two monitors with this computer in its current configuration is using a monitor with VGA input and a monitor with DVI - D input.

    Please provide the number of brand and model of both monitors you are trying to connect to your computer. This will allow us to determine options that you have with your existing monitors.

    Please send Bravo

  • Yoga loading 500 for a second, then does not charge for a second

    Hello. I recently bought a Lenovo Yoga 500 laptop, and I am very disappointed. When I plug my charger, 9/10 times it starts to require, immediately stop charge, then charge again for a second. This translates to never charge. Finally, she normally perceives, but it is completely random and sometimes requires 5 + restarts. I need this laptop for school so take off for repair is difficult for me but I'll do it if there is no other way. I received a second charger from a friend, and in this case yet, so the problem is not with the charger. Someone has an idea for a fix?

    Thank you

    The energy Manager reintsall has failed. We took the laptop and they recognized the problem and that it is a manufacturing defect. We got a new back, problem solved

  • Application that was open on the second monitor does not open on the main screen without the second monitor attached

    At my office, I have a second monitor. One of my apps has been posted on this subject. I think I left the application; disconnected the monitor; and stop Windows XP.

    Now, my application wants to open on the second monitor which is not present.

    Is it possible to open the laptop monitor? Charles Allen Managing Consultant BKD Technologies

    Start the application, right click of its mosaic in the taskbar and click move .  Use the arrow keys to move to the first monitor, and then press enter .

  • My printer is connected to two computers. I find that the second computer does not print unless the first computer is also on. Can I get every computer to print without the two be on?

    the printer has been first on windows 7 and second on windows xp, because that's the way I was told iy had to be done. But I thought that each computer can print separeately withou t windows 7 being on.

    Hello

    1. How is the printer connected? This printer is on a network?
    2. this configuration was already working before?

    You must configure a print server. If your printer is a network printer, you can connect it to a router, and all computers connected to this router can use the printer individually. If the printer is not a network printer, you can buy the equipment to turn it into one.

    See the articles below for more information:
    http://support.Microsoft.com/kb/308028
    http://TechNet.Microsoft.com/en-us/library/bb457001.aspx

    I hope this helps.

  • computer beep will sound every 3 seconds and does not stop while the computer is on... why not? How to stop it? __

    My new Dell Inspiron 1545 beeps (like a USB stick is plugged or unplugged) every 3 seconds, without judgment, without doing me anything to provoke. I turned the computer off and back on several times, but the noise persists.

    Why this is happening? How to stop (without just turning off the sound)?

    Yessim

    http://support.Dell.com/

    As this is a brand new computer, it is under warranty.

    http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_technical_support

    http://en.community.Dell.com/support-forums/default.aspx

    Dell Support Forums

    Please contact Dell at the link above.

    And the Vista Forums.

    See you soon.

    Mick Murphy - Microsoft partner

  • My second monitor does not display anything

    My computer worked fine and both of my monitors worked until recently when my second monitor stopped show all. My computer is always picking up as connected and on but the screen is black and no backlight, my monitor is not working is a hp w1907 and light on the upper part is the color it is on and not asleep. When I turn off my monitor and turn it back on it displays for the new school year second but then just a few no display. And before that I did my second monitor was my main monitor and it worked fine. I tried to make sure that the plugs are connected and tight and that everything was normal with the pilots and the son and everything worked. I have a Sapphire hd graphics card 7970 and plugs all work. Please help me solve this problem.

    Sincerely, McKane

    I tried the monitor in the other port and it still doesn't work so I decided that my monitor is dead and I cand do anything to fix it

    Then, almost certainly, the problem is that the monitor is dead. Especially if it used to work, it is unlikely that ther'e a driver problem.

    You might want to try the monitor to a friend's computer to verify that it is their work.

Maybe you are looking for