Unable to access the remote PC APEX using url
Hi allI'm under 11g R2 on a desktop computer and that you have configured APEX 4.1. I am able to access all of the pages that I should be able from a browser on localhost.
But I am trying to remotely access from PC, I Internet Explorer can not display the webpage.
I have read the documentation and tried everything I could think or find all to nothing does not. It's my first attempt @ APEX, so I'm learning.
Any suggestions on what to check?
I use the
by default the port of * 8080 *.
Installation shows as valid
Public_User is unlocked
Hello.
Check your settings in firewall Windows/Linux/mac
Eduardo
Tags: Database
Similar Questions
-
Unable to access the remote host
Here is the configuration of pix of my client, the problem, here is... whenever it uses a Cisco VPN dialier, it can connect to the VPN, but cannot access any host on the distance, but with the same vpn Dialer & VPN pcf file, when it is used with a connection high speed which is not route with this PIX (or not behind the PIX) It works very well. Yet one thing I noticed, it's only when I give a static NAT, it is able to access on the remote & not through a NAT GLOBAL PC when the PC is behind the PIX.
6.3 (3) version PIX
interface ethernet0 car
Auto interface ethernet1
Auto interface ethernet2
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
nameif dmz security50 ethernet2
enable encrypted password xxx
enable encrypted password xxx
TA.qizy4R//ChqQH encrypted passwd
fixup protocol dns-maximum length 1024
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
No fixup protocol sip udp 5060
fixup protocol 2000 skinny
No fixup not protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
access ip-list 110 permit a whole
access-list 120 allow icmp a whole
access-list 120 allow esp a whole
logging console warnings
Monitor logging warnings
logging buffered stored notifications
recording of debug trap
the logging queue 0
Outside 1500 MTU
Within 1500 MTU
MTU 1500 dmz
IP address outside x.x.x.x 255.255.255.240
IP address inside 192.168.0.1 255.255.0.0
no ip address address dmz
alarm action IP verification of information
alarm action attack IP audit
IP local pool homeuser_vpn 192.168.1.1 - 192.168.1.254
location of PDM 192.168.0.80 255.255.255.255 inside
location of PDM 192.168.0.207 255.255.255.255 inside
location of PDM 0.0.0.0 0.0.0.0 outdoors
forest warnings of PDM 100
history of PDM activate
ARP timeout 14400
Global 1 x.x.x.66 (outside)
NAT (inside) 0-list of access 123nonat
NAT (inside) 1 192.168.0.0 255.255.0.0 0 0
public static x.x.x.70 (Interior, exterior) 192.168.3.1 netmask 255.255.255.255 0 0
public static x.x.x.76 (Interior, exterior) 192.168.3.2 netmask 255.255.255.255 0 0
static (inside, outside) x.x.x.77 192.168.3.3 netmask 255.255.255.255 0 0
Access-group 120 in external interface
Access-group 110 in the interface inside
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
the ssh LOCAL console AAA authentication
source of x.x.x.x server NTP outside prefer
Enable http server
http 0.0.0.0 0.0.0.0 outdoors
http 192.168.0.207 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Telnet 192.168.0.197 255.255.255.255 inside
Telnet 192.168.0.80 255.255.255.255 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 192.168.0.0 255.255.0.0 inside
SSH timeout 60
Console timeout 0
dhcpd lease 3600
dhcpd ping_timeout 750
username admin password encrypted xxxx privilege 15
username password encrypted xxx privilege 2 admin1
Terminal width 80
Cryptochecksum:xxx
: end
# 123
Anand,
I would check to make sure that the N - NAT has something like: -.
"permit access ip 192.168.0.0 list 123nonat 255.255.255.0 192.168.1.0 255.255.255.0.
And enable NAT - T - she might be his house do not understand/IPSEC passthrough device support:--
"isakmp nat-traversal 20.
And add: -.
"access-list 120 permit udp any any eq 4500.
HTH.
-
How to access the remote database by using express application server
I wan to access the database in one of my servers of laboratory since my laptop remotely. I could easily connect to the server when I use the LAN by simply giving the ip address. But it does not work when remote. I installed PuTTy to connect to the server (that I have), but now I want to access the specific request of this database in the lab server. Is it possible to do?
Any help would be appreciated.
Thank you
Hi 3030553,
3030553 wrote:
Please change your login username of "3030553" to something meaningful. Reference: Video tutorial how to change username available
I wan to access the database in one of my servers of laboratory since my laptop remotely. I could easily connect to the server when I use the LAN by simply giving the ip address. But it does not work when remote. I installed PuTTy to connect to the server (that I have), but now I want to access the specific request of this database in the lab server. Is it possible to do?
Your laptop must be in the lab server LAN network to access, or else you should have the VPN connection to the LAN in which the lab server exists.
Also to access objects of database in your schema to Application Express workspace, you can use the workshop of SQL as mentioned by Tommy or you can use Oracle SQL Developer, since you have the credentials for the schema to connect to and related IE required database server information full domain name / ip address of the server port on which the listener database service is running, database SID/database service name listening.
Kind regards
Kiran
-
Cisco ASA 5505 unable to access the remote network
Hello
I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.
ASA IOS version 8.2 (5)
Remote IP network: 10.0.0.0/24
VPN IP Pool: 192.168.102.10 - 25
I have attached the config: llc.txt
Please let me know if you have any questions.
Thank you!
Hello
Try adding NAT 0 because inside subnet--> subnet distance
NAT (inside) 0 access-list TEST
TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224
HTH
MS
-
Unable to access the remote VPN LAN
My VPN ends very well, but cannot access the local network. The warning is the LAN is a public good 24 subnet. I'm not sure how to NAT the LAN to access the VPN subnet and not to disturb any other functionality. I have attached the configuration.
Thank you in advance.
ciscoasa # sh run
: Saved
:
ASA Version 8.2 (2)
!
ciscoasa hostname
activate the encrypted Anuj/1RTcTy/SmZO password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP address .149.200 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address *.165.37.131 255.255.255.248
!
interface Vlan5
No nameif
security-level 50
IP 10.10.10.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone GMT 0
standard permit access list MASTERPWRTRANS_splitTunnelAcl *. . 149.0 255.255.255.0
allow inside_nat0_outbound to access extensive ip list *. . 149.0 255.255.255.0 172.30.110.0 255.255.255.224
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
local pool POOL1 172.30.110.1 - 172.30.110.30 IP 255.255.255.224 mask
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
Global (outside) 2 *.165.37.132
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 2 *. .149.199 255.255.255.255
NAT (inside) 1 0.0.0.0 0.0.0.0
static (exterior, Interior) *. .149.199 *.165.37.132 netmask 255.255.255.255
Route outside 0.0.0.0 0.0.0.0 * 1.165.37.134
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol Server AAA MPT
AAA server MPT (inside) host .149.210
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
Telnet *. . 149.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access insidea basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal MASTERPWRTRANS group policy
MASTERPWRTRANS group policy attributes
value of DNS server *. . 149.10 *. . 149.11
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list MASTERPWRTRANS_splitTunnelAcl
MCI.local value by default-field
ptiadmin encrypted BtOLil2gR0VaUjfX privilege 15 password username
mptadmin U2T.1fmOIe772zE username password / encrypted
type tunnel-group MASTERPWRTRANS remote access
attributes global-tunnel-group MASTERPWRTRANS
POOL1 address pool
TPM authentication server group
Group Policy - by default-MASTERPWRTRANS
IPSec-attributes tunnel-group MASTERPWRTRANS
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:820529ed70de923a8375694004b2544c
: end
ciscoasa #.The 2821 should have a route pointing to the ASA for the VPN address pool (because the ASA is not the default gateway for the LAN).
That should do it.
Federico.
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
Unable to access the network using Edimax N300 universal Wi - Fi extender
Original title: Edimax Extender will not get internet access
I naoual got a N300 Eimax universal Wi - Fi extender but I am unable to connect to the internet. They suggest setting up near the wi - fi access point to get the signal stronger and I got to show connected in the window ' currently logged in ', but it does not connect to the network. EDIMAX has proposed upgrading the firmware, but I was unable to get any joy with that either. Anyone with any ideas would be appreciated.
Hi Gofchap,
Thanks for the question of validation in Microsoft answers community!
I imagine the frustration you feel when you are unable to access the network.
The problem may be because of the Extender, diverter, or with the network adapter.
1 did you do changes on the computer before the show?
2. do you receive any error messages?
3. What is brand and model computer?
4. have you tried to connect without using the extender?
I suggest you to visit:
Wireless and wired network problems
I hope this helps. If the problem persists, let know us and we would be happy to help you.
-
Unable to access the store using the proxy server.
I'm in Windows 8. I'm unable to access the app Store. He said:-"we were not able to connect to the Store.This could not have come because of a problem with the server or the connection network has expired. Please, wait a few minutes and try again.and some other applications also. I use a 1.1 proxyserver (squid) that requires basic authentication.
However I m able to use some of them as weather, maps, etc.I read solutions who suggested to temporary disable firewall and antivirus for test, I even try it but fails again.
Other suggestions where has been going for windows 8.1 upgrade level, but how can I get this update, as it is downloaded in store that I can't access. Help, please.
Hi Anand,
Your computer is connected to a domain?
Using a proxy server can allow the administrator to limit access to the Internet.
You can reduce the effect of these problems by allowing unauthenticated through your proxy server access. We recommend that you enable unauthenticated access only for connections to URLs used by each application that has a problem. Some proxy servers may suggest that you create a list of URLs (also known as the 'white list') permissions.
Please refer to the article to address these issues that relate to the use of Windows Store apps or use of Microsoft applications that are included with Windows Update or Windows 8, you can include the addresses mentioned in the article in a list of permissions ('white list') on your proxy server and enable HTTP and HTTPS access for them :
The use of proxies authenticated with Windows 8
For more information, see the article:
Using the Proxy selection and Proxy bypass lists
You can also consult the steps by Rajesh Govind, Support Engineer, may 4, 2013 and check.
Windows 8 apps not able to detect the proxy for my machine settings.
Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.
-
Firefox is unable to access the internet
Hello
Firefox is unable to access the Internet. Internet in the phone works, because all applications in my phone are able to access the Internet. I tried to access several different web pages. Their work. The screen is all black, no error messages appear. The strange thing is that Firefox Sync seems to be able to connect to the server, and I can download plugins.
Best regards
Joel HedestigYou can try using the beta version of firefox mobile?
https://play.Google.com/store/apps/details?ID=org.Mozilla.firefox_beta
-
We have a Nextbook but are unable to access the Internet at home
We have a Nextbook but are unable to access the Internet at home, even if we have a laptop and PC. How to solve this problem? Thank you.
Hi Vernon,
1. you are trying to connect the Nextbook to wireless (Wi - fi) network in your home?
It is a tablet based on Google's Android. As it comes to one product other than Microsoft, I suggest that get you in touch with the manufacturer about this issue. You can contact them at the following link:
http://www.nextbookusa.com/techsupport.php
Hope this information is useful.
-
I'm unable to access the Web site rewards club mail
I'm unable to access the Daily Mail online REWARDS CLUB site WEB TO ENTER MY NUMBER ONE
Hi BrianSheridan,
1. what happens when you try to connect to the site?
2. you receive an error message?
3. what web browser do you use?
4. what version of IE are you using?
5. are you able to open the Web site in the other computer?
If you use Internet Explorer, then perform the following troubleshooting methods:
Method 1:
Optimize Internet Explorer, and then check how it works.
Check out the following link to optimize Internet Explorer.
How to optimize Internet Explorer
Note: This article is also applicable to Internet Explorer 9.
Method 2:
Also perform the following troubleshooting steps.
Can't access some Web sites in Internet Explorer
Method 3:
If you use Internet Explorer 9, then perform the steps in troubleshooting at the following link.
Some sites Web may not behave as expected in Internet Explorer
-
Original title: I tried to apply the photo viewer to open a file and the photo viewer icon replaced each icon on my desktop. Now I can't open anything on my desktop. What is going on?
The name is below the icon, but the correct icon has been replaced by windows Photo Viewer icon. When I click to open it, it says: windows Photo Viewer cannot open this photo because Photo Viewer does not support this file format, or you do not have the latest updates... I don't know what I did!
Hi,
Thanks for posting your question in the Microsoft Community.
From your problem description, I understand that you are unable to access the photo viewer; and also cannot access the desktop icons because they are changed to the photo viewer icon. Please let me know if you do not experience this problem.
I understand the inconvenience caused to you. I'll help you solve the problem!
Before troubleshooting, I have little information on the issue.
1. did you of recent changes to the computer before this problem?
Try the methods suggested in the article below and check after each method:
Method 1: Icons change incorrectly in Windows: http://support.microsoft.com/kb/2396571
Registry warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the in the Microsoft Knowledge Base: 322756. How to back up and restore the registry in Windows: http://windows.microsoft.com/en-us/windows-vista/Back-up-the-registry
Method 2: Run scan files system (CFS) auditor, to repair missing or corrupted system files.
How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7: http://support.microsoft.com/kb/929833
If the problem persists, post your reply with the results and the questions asked above. We are happy to help you further in the advanced troubleshooting steps!
It will be useful.
-
Unable to access the BPM UI composer despite the installation of BPM Suite 11 g
Hello
I installed the suite BPM (& SOA suite too) but even after starting Admin Server and managed server (soa_server1), I am unable to access the composer BPM (I'm
with the help of URL similar to http://host/bpm/composer) if I can access WLS console, EM, BPM worklist application etc. correctly. I just wanted to check, what else to do to use BPM dial? Kindly let me know.
Thank you
HardHi harsh,
Did you also put the news of port as following: http://localhost: 8001/bpm/composer
Kind regards
Rommel Pino -
Unable to access the doc object
Hello
I'm unable to access the doc object, as in doc.mailForm ().
I tried to access this object as follows, a field event and a global module:
This.doc (undefined)
App.doc (undefined)
Event.Target.doc (undefined)
doc (blocks JavaScript).
The app object is OK, I can use app.alert ().
I use Designer version 8.2.1, using a dynamic XML form.
Just use event.target which will return the doc object.See the code example belowvar doc = event.target;doc. Print();doc.saveAs ();doc.closeDoc ();Nith
-
MY mail server hardisk full so cannot start services & also unable to access the mail server
I have the server messaging, but Hardisk ful then failed to start Services and also unable to access the e-mail mail server troubleshooting steps.
Hello
The question you have posted is related to professional level support. Please visit the below mentioned link to find a community that will support what ask you:
http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer
Maybe you are looking for
-
Sites without favicons show the place of the border dotted, but those with the icons are just gone.
-
How do I install the cd - dvd driver and hence
I use a drive cd - dvd but now Im receiving to reinstall.How and where? my driver installation disk? or...
-
New Ebay photographic requirements (detailed photos/images)
New changes to eBay (photo size recommendations) are effective from July 1,2012. Is there any way or method available I can use to "resize images" which I downloaded from a site "the provider" to show more detail. I need to do to meet the new standar
-
recharge the laptop battery via USB
I'm going to take a long flight (10 hours) and want to use my 2 want my eReader than him. Is it is possible to recharge the battery using a USB cable?
-
Forms and reports 10.1.2 home - EBS 12.2.0
I'm missing something here...We just finished a new installation of 12.2. I see a lot of homes of source in the .env file but do not see a House OracleAS (10.1.2) origin.Is it normal?Thank you