Unable to connect to any network

Similar Questions

• Extremely low signal wireless unable to connect to any network

  Hello

  I bought just a Studio 1535 and can not get the wireless to connect to any network unless I put the computer 2 feet or closer to the router.

  I am running Vista Home Premium, and according to the Device Manager my wireless is a Dell Wireless 1397 WLAN Mini card.

  When I'm right next to a router, I can connect either password protected or not.  Also, I have other computers can connect to each network without any problems.  I know that this is not a router problem.  I tried with several different routers and several different locations.

  I can see a long list of points connect wireless, each with what reads like excellent signal.  However, when I tell the computer to connect, I get a screen "Windows cannot connect to the ____."  When I select diagnose the problem, it says "Wireless association failed because windows did not receive response from the access point or wireless router.

  Dell support will not help me because I bought the computer at Best Buy and Geek Squad wants to send my computer is turned off (which I had for a day) to be diagnosed.  I would rather here check everything first...

  Thanks to all helpers, let me know what information you need from me!

  
  

• Pavilion 14-ab051tx N4G24PA: unable to connect to any wireless network after the upgrade to Windows 10

  I recently bought a 14-ab-51tx Pavilion N4G24PA, this is my first laptop from HP, it comes with Windows already installed 8.1 and it worked fine.

  The thing is, I kind of get used to using Windows 10 on my previous laptop, so without further hesitation I upgraded to 64-bit Windows 10.

  Here's what I did wrong:

  Instead of update Windows 8.1 for Windows 10, I indeliberately he installed fresh, with couple of mouse clicks, I didn't realize that I also remove the recovery partition.

  I realized only after the installation process is complete, but then it was too late. I look forward to using my laptop with Windows 10 freshly installed inside to make some games just noticed that I couldn't connect to any network without wire, House or public. It recognizes my wifi at home, but the signal bar is bizarre, there is only 1 bar of signal even if the wireless router is only about 10 feet from him, so I checked my other computers and smartphones, but the signal on them is ridiculously high (full bar), it also detects another wireless network that are further away than my wireless router.

  But back to my HP laptop, I tried to connect to my home network despite the signal bar with the right entry security key, but it does not connect, it says "Cannot connect to the network".

  Tried updating drivers with HP Support Assistant and no luck, the problem persists, tried all the solution on the internet, int ip reset, reset winsock, checking and unchecking, always without success.

  Can someone help me please...

  Hello:

  The BOM indicates that your laptop comes with a Broadcom wireless card.

  Have you tried the last W10 driver for this card to support your PC and driver page?

  This package contains the Broadcom Wireless LAN drivers for the laptop models running a supported operating system. Broadcom wireless LAN drivers are required to activate the built-in Broadcom wireless LAN adapter.

  Exit the: December 17, 2015

  Version 7.35.317.0 Rev.A

  File name: sp74241.exe

• Unable to connect to a network printer

  I am unable to connect to my network printer, even if when I run the command 'Connect to the printer' and select 'network', while the program is able to see my network printer, it crashes when I select the printer.

  I was able to connect to the printer in the past, but for some reason any printing interrupted.  I deleted and reinstalled the printer (HP OfficeJet Pro 8600) with the CD that came with the printer and once again, while trying to connect it froze.

  Any suggestions would be greatly appreciated.

  Hi André,.

  Welcome to Microsoft Community where you can find all the answers related to Windows.

  According to the description provided, looks like you can not connect to the network printer.

  I have a couple of steps, which I think should help you with this problem.

  Method 1:

  Try the steps mentioned in this link and check:

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Method 2:

  Visit this link to learn more about "Troubleshoot network printer."

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  In addition, visit these links and check:

  What are printer permissions?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-printer-permissions

  Troubleshoot file and printer sharing

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-file-and-printer-sharing

  Hope this information helps. In case you have issues with Windows, post here to Microsoft Community.

• Unable to connect to a network or to the Internet on my Dell XPS1530.

  Unable to connect to a network or to the Internet on my Dell XPS1530. When I try to diagnose problem, I get a message that reads "Network Diagnostics cannot run because the Diagnostics Policy Service is not running." Having exhausted the patience all the phone with my IP and Dell, which tells me that it is a problem of Microsoft software. I have two other computers and a PS3, and I am able to connect to the Internet through one any of them. The XPS works under Vista with SP2. Can someone help, please? Thank you.

  Go to start / Control Panel / Administrative Tools / Services and go to diagnostic policy Service and set it to automatic and start it.  If it does not start, check the dependencies and make sure they're too automatic and rnning.  Then see if you can run Network Diagnostics.

  You can get in trouble with your device drivers.  Go to Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you should get those developed to date for the network card and regardless of the device you use to connect (such as a router wireless or such) and all you have time to do - they can help way beyond simply solve this problem), let the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.

  When I'm in a lke your situation, I usually start from scratch.  Create a new network connection by ensuring that all settings are correct.  Check all the cables (if there is).  You have already reinstalled the drivers - make sure that no firmware or software is also necessary.  Configure the network sharing settings and make sure that you are ready to discover the network and such.  Check other computers to see their settings to make sure you get yours right and essentially the same thing (the same exatly so is another Vista machine connected in the same way).  Go to start / Control Panel / Internet settings and make sure that it's too fixed properly.  To connect, then try again. If this is not the case, remove some time to cool down and then start again with another new connection.  It's almost certainly a parameter that is not correcct (something no doubt very simple).

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• on startup, I get the message, unable to connect to all network drives

  at startup I get message (unable to connect to all network drives) I use windows 7, intel i3, 64-bit and ie9.

  Hello

  Were there any changes (hardware or software) to the computer before the show?

  Method 1: Perform the steps from the link below and see if it helps.

  Programs may be unable to access some network locations after you turn on user account control in Windows Vista or in Windows 7

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  Method 2: Click on the link below and see if it solves the problem.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Networking/cannot-reconnect-all-network-drives/5c5a4492-1634-4479-91f9-b4d2763b31d2

  Hope this information helps.

• My MacBook froze during the installation of the update at El Capitan and now I am unable to connect to any except the screen of the guest user. There was a message of panic, and somewhere in there, he said no set of OS. I tried to start without danger, it

  My MacBook froze during the installation of the update at El Capitan and now I am unable to connect to any except the screen of the guest user. There was a message of panic, and somewhere in there, he said no set of OS. I tried to start without danger, it does not work either.

  This general situation may be similar to what is mentioned in this sequel to thread of the CSA

  and if the remedy is to use instructions; detailed and I hope they are correct...

  Re: Restart fails after installation of El Capitan help!

  Or you can try and see on the repair of the system and then if your disk utility can

  See the Macintosh HD, as a boot volume, you could restart from OS X Recovery to

  the Mac system, to see if this solves the problem. There may be more than one cause.

  You could try and boot into OS X Recovery, utilities out there, and other options are available.

  • OS X: on OS X Recovery - Apple Support

  This example uses a special partition on the hard drive of recovery which is not in the

  same disc that the Mac OS X section; However if your hard drive is missing, these other

  items may also be at risk. You must have and maintain backups of your duplicate content

  on the external storage drives closed; In addition, a Time Machine backup helps to restore.

  • Apple OS X and Time Machine tips:

  http://pondini.org/OSX/home.html

  • Tips for OS X - using HD recovery:

  http://pondini.org/OSX/RecoveryHD.html

  {Using the utility disc and other tools can be done from the boot OS X Recovery volume

  Beware of the fact these tools can also delete or reformat your content; wiping.}

  Don't know what to say; you could see visiting an Apple store with genius if

  There is an official store. Usually for best time planning you would contact them for an appointment.

  • Make an appointment at an Apple Retail Store Genius Bar
  • Find an Apple authorized service provider
  • https://locate.Apple.com/country - Apple - find places - selector of country (if outside the U.S.)

  Or if there is no official retail Apple Store with genius, the following suggestion would be to contact

  a service provider authorized Apple, an independent specialist who is qualified in the repair of Apple.

  In any case...

  Good luck & happy computing!

• Unable to connect to wireless networking

  My Toshiba laptop has been pre-installed with Windows 7 Home premium 64 - bit OS and it worked quite well with the BB wireless. However, the wireless internet was on and turned off in recent weeks, while other mobile devices, such as iphone, ipad, or laptop, in my household had no such problem. The wireless signal was so strong, but the error message always says "unable to connect to wireless networking. It seemed that there was something wrong with the wireless adapter.

  I got a new adapter properly installed TP-Link wireless. Fortunately, it worked; but unfortunately, it worked for less than 24 hours. It was really frustrating that I, like student full time, depended so much on the wireless network card.

  Help, please! Harry

  Hello

  You can enlighten us with:

  -What model do you use (eg..) L300-123)
  -What version of BIOS is installed?
  -WLAN driver do you use?

  All these questions are answered in PC Diagnostics are under Toshiba app folder in the start menu.

  BR

  Tom

• currently not connected to any network

  I have a HP Omni 100-5050 all in one office. Windodws 7

  Recently, it does not connect to the internet, and I get the message "no connection available.

  When I go to network and sharing Center, I get the message "currently not connected to any network.

  Until a few days before, everything was fine.  The only thing that may have changed, was an automatic

  update windows.

  I called HP support, and they offer a fix for a price.  Is this the only option I have?

  Help!

  PS My laptop is connected to the same network and works fine

  Thank you for the additional information.

  I am not sure, but I don't think that there is a wireless switch on the keyboard there is on most laptops.  This is considered as a desktop computer.

  Have you updated the driver wireless?  This may solve your problem.

  As a last resort, you may need to perform a system recovery.  This will take the computer to its original configuration.  You should back up your personal data if you decide to go this route.  I do this at least once a year.  He always makes the computer run better.

• You are not currently connected to any networks

  I have an acer aspire 5552 with windows 7. I have upgraded to windows 10 but because I could not fully access to my LAN, I went back to windows 7. Now windows 7 says I'm not connected to any network, while the cards are there and their settings can be changed. No network appear in the network and sharing Center. The status of the local network adapter and the wireless adapter is not connected, IPv4 and IPv6 not connected. I reloaded the drivers for 2 adapters but no change. I really want to go back to the factory State.

  Can someone help me?

  Thank you revomaxx.

  the solution proved to be the associated firewall. I use comodo firewall. When I unchecked the comodo selection in the network card settings, everything worked all of a sudden. I then reinstalled comodo and all was fixed.

• Not connected, you are currently not connected to any network.

  When I'm on the network icon or click on it says "not connected, you are currently not connected to any networks." I know I'm connected but how am I guess sharing media with friends now, it's kind of a big deal for me and I tried to remove the network and then restart and then re-login has always the same thing happens as my security type is WPA2-PSK , but he says WPA2-Personal, when I go to manage wireless networks, I guess that means the same thing so can you help me more im going to upgrade to windows 7 soon and I don't know if he's going to say the same thing, please help.

  Hello

  1. don't you make changes to your computer before the problem?
  2. what type of connection you are using?  Cable?  Wireless?

  Search for related errors in the event viewer.

  Test in safe mode with networkproblem.

  See also: http://windows.microsoft.com/en-US/windows-vista/The-doctor-is-in-Using-Network-Diagnostics-in-Windows-Vista

• No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  No network adapter driver is available after reinstalling Windows Vista installation disk... Unable to connect to the network

  Hello

  Know what type of network card you have and download the drivers of its supplier.

  It doesn't matter what it is always a good idea before re-install/upgrade to log on to the computer support page, download independent drivers from there and put them on a flash drive.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Unable to connect to the network because the parameters of the computer do not match the requirements of the network.

  The main computer in my house is connected to the web via a modem to our ISP (Cox).  We use a Cisco's Linksys wireless router.  We have configured a new laptop to connect through the router yesterday.  Now my laptop, which had been the connection very well, can't access the network.  When I go in the "network and sharing Center" and pull up nearby wireless networks, our network shows is even more bars, just a red X.  Reads the error message "unable to connect to this network because the settings of that computer to match the parameters required network.»

  I don't know what has changed on our network, but I was unable to understand what these "required parameters" are, so I was unable to change the settings of my laptop to match the requirements.  Pls help.

  Hi Sharpdale,

  Step 1

  I first suggest you to perform network troubleshooting in Windows 7 and check if it finds problems, and if he is able to fix it.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Step 2

  Use Windows to configure wireless settings and check if it helps to solve the problem.

  a. click on Start menu and select run

  b. type ncpa.cpl, and then click OK to open the menu of the network connections.

  c. Select your Wi - Fi connection service and choose the option change settings of this connection.

  d. go to the wireless tab and select (tick) labeled use Windows to configure my wireless network

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to connect to a network error - change wifi profile native default

  Unable to connect to my network. When I try to see my network it says wifi native default profile

  
  Original title: change the profile default native wifi

  Hello

  Thanks for posting your question on the Microsoft Community Forums!

  From the problem description, I understand that you can not connect to the wireless network.

  For a complete list of the steps to try, see the tutorial wired and wireless on this page.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/is-is/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  It will be useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• Unable to connect to this network

  I have a samsung series 7 chronos 2013 np780z5e the intel centrino n advanced wireless installed, running 64-bit windows 8 6235 card. I can connect to my home network with wpa2-personal encryption and the public WiFi at my University. However, I can not connect to wpa2-enterprise security connection. It finds the network credentials and then immediately provides the message 'Unable to connect to this network', without asking for credentials. This network works fine with other laptops, and I can even connect with my phone. I think it's a matter of windows 8.

  I tried the automatic network troubleshooting and updating to the latest drivers, but neither have worked.
  Update: after network oversight, update drivers and reboot, it works now. Either reboot or forget the add new network and fixed the problem

  Hello

  The majority of connection to Windows 8 breast problems have been resolved by installing the latest driver for the wireless card with obtained from the manufacturer.

  Thanks for sharing the information. In case, if you need help, you can always after your questions related to Windows and your valuable suggestions in the Windows forum.