Unable to connect to cRIO (OK in MAX)

Similar Questions

• Unable to connect wireless, "ACS user exceeded max sessions" users

  Some corporate users are unable to connect to the wireless company.

  On the WLC, I get the following logs:

  Authentication failure AAA for UserName:dto029 user Type: USER WLAN

  The GBA, I get the error:

  Authentic doesn't have a default group for ACS user exceeded max sessions (by default) 192.168.47.46 DTO029......

  That means "user ACS exceeded max Sessions? How can I solve this problem? Connection problem faces few users, while others are able to connect.

  Corporate SSID, Session Timeout & Client Exclusion is not enabled. The WLC version is 7.0.98.0 and the version of the CSA 4.2.0.124

  The problem is solved the ACS is restarted. Is there a permanent solution?

  Thanks in advance.

  Hello

  the error means that the users belong to the ACS Group (or the user themselves) has a "max session" setting, as described here:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/Overvw.html#wp826493

  .. and the user exceeds this limit.

  ACS can indeed limit the number of concurrent sessions for the same user name; This counter is based on the RADIUS account management information received from the AAA client: the session counter is increased when receiving a 'Start' accounting and it is decreased when you receive a "Stop" on accounting package.

  ACS for a reason if any don't receive an Acct-Stop, it won't reduce the number of session, so it may happen that your users exceed the max concurrent sessions allowed indeed.

  You can check the active sessions on the "users" ACS report:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/LgsRpts.html#wp680304

  If you restart ACS, this info is reset, so everything will work again, as you say; as an alternative, you can also use the options 'Purge logged in users' on the logged users page, but it would be wiser to really solve this problem by checking if... :

  -do you really need the config of max sessions? Otherwise, you can simply disable this on users/groups configuration

  -If you need for this limitation and the problem is related to the session that overlap, which means that the WLC should not send the Acct-Stop because there is always a session active and a new one is created at the same time, you can consider increasing the number of maximum session.

  HTH,

  Federico

  --

  If this answers your question please mark the question as "answered" and write it down, so other users can easily find it.

• Unable to connect/configure PSC 2020 using MAX

  Hello world

  It's something like 'part II' to try to use the serial ports on our PSC 2020.

  I received a lot of help and valuable advice from Ravens Fan and others of the Spanish community in regards to the series, and I really appreciate their help.

  However, just at the point where I was about to make the first test, after you advise them, someone in my Department decided, there are a few days to clear (or format) all the contents of the memory of one of our CFP-2020. In addition, there is an another PSC 2020 which was unused for a long time. Well, the point is that none of the two controllers is seen by MAX, and therefore they cannot be configured by MAX either. Both are simply a blank space (i.e. nothing appears) under remote systems or devices and interfaces or another area in the configuration tree.

  Another important detail, we used an earlier version (4.xx, I guess) and also a newer version (7.x.x, I guess) of MAX trying to win again the communications. None of these versions could not communicate with one of the CFP-2020. In other words, none of these versions could establish communication or to show a sign of life of one of the two controllers. We test the wiring and it worked perfectly with the other PSC 2020 we have in existence.

  I guess that LabVIEW 7.1 or 8.0 (versions that we have) will not be able to communicate with controllers or if MAX has failed before. Am I right?

  Is there another way to see (contact) the CFP-2020?

  Is there a procedure for 'must - after setting shaped' that we are missing?

  This behavior has something to do with the DIP switches in the cFP2020?

  Is it possible to say if controllers are broken (fatal hardware failure) or if it's just a matter of software configuration?

  The deadline to begin a period of testing laboratory with the cfps 2020 is very narrow, and I really need to retrieve both controllers, so I would really appreciate help for this problem.

  Best regards

  I am pleased to have been able to help so far.  Let me see if I can help even more.

  First of all, to find a big stick and go fight anyone who formatted your controller overhead.

  Second, if you don't see anything under remote devices, I'll guess that the controller has been the installation of another IP address on a different subnet than where you are now.  I would try the instructions on page 3-6 of this Manual to reset the IP address.  That set it back on a 0.0.0.0 address who should make them findable by MAX again.

  Thirdly, MAX is up to version 4.6.2 (perhaps under minor version or two later.)  So, I'm not sure "newever version 7.x.x" unless you have a version number of LabVIEW.  Yes, you will certainly get the controller found in MAX before LV can work with it.  Definitely check the DIP switch as safe mode and reset the IP.  It is possible, that there is an incompatibility of drivers fieldpoint between the remote control and your LV version but I think that the two would have to endure somehow offset, otherwise you wouldn't be able to update the fieldpoint drivers in the controller.

  If there is a problem with the controller, I don't know how to determine that.  A person of OR may be able to help.  I think that the most likely scenario is that the last IP address defined for the controller corresponds to the setting for your PC or network, you are now, in which case the IP reset should help that.

• Can ping cRIO but unable to connect to the MAX

  I have a cRIO 9066 put in place on a local subnet. I think that all the software and drivers are correct. I have deployed my program and it works great except... When I add some optical converters of fibre in the mixture. Here is my system:

  PC--> cable ethernet--> ethernet switch-->--> cRIO ethernet cable * it works fine *.

  PC--> ethernet cable--> converter of fiber--> fiber--> ethernet switch (FPS)-->--> cRIO ethernet cable * unable to connect to MAX *.

  When I connect with ethernet cables all the way through, the ping time is<1ms ttl="" is="" 64.="" when="" i="" add="" the="" fiber="" converter,="" i="" can="" still="" ping="" the="" crio="" but="" ping="" time="" goes="" to="" ~250ms="" and="" ttl="" goes="" to="" 247.="" then="" max="" can't="" connect="" to="" the="" crio.="" is="" my="" connection="" speed="" too="" slow="" for="" max="" or="" the="" crio="" to="">

  My converter fiber and ethernet sfp module switch are all 1000 MB/full duplex. It is run only on a 10 m fiber. I tried several fiber optic cables. I tried the sfp in several locations. My sfp and the switch are both Advantech so I guess that they are compatible with each other. At this point, I plan to buy just a card PCIe fiber for my PC, but I thought I should check first with the experts.

  Thank you

  Hello

  There is a timeout OR max. The default value is 4000 Ms the reason why you are not able to detect the cRIO in NOR-MAX may be because the packages are damaged along the way. If you do not want to check this, you can always monitor the packets with WireShark with two different sets high. In this way, you can see if the packets are defined correctly or not.

  I hope this helps!

• connection intermittent cRIO (with MAX, etc.)

  Our cRIO connects to our fine PC when it is initialized at first - and you can view it fine in MAX, Manager of distributed system and its web interface. But after all 3-5 minutes it always loses connection. It remains disconnected, and only restart the cRIO restores the connection but only for another 3-5 minutes. Only MAX restart does not help. We can ping the cRIO ok when 'disconnected' - which, to me, implies that it is a problem of higher level software.

  We had this particular cRIO work fine before.

  Thanks for your suggestions... While not in a rush to do this, I really want to understand why the connection is intermittent

  Here are some details:

  • MAX version 5.0.0f1
  • LV2011 DS2
  • cRIO is a 9022 (no screws running on it to the commissioning, CPU minimum load - idle = 97%)
  • computer development is a Vista Home Premium 32 bit
  • connected together using the brand-new Cat5E cable
  • TCP/IP settings on the laptop - Static IP, IP 192.168.2.4 address, mask 255.255.255.0
  • TCP/IP settings on cRIO - Static IP, the IP 192.168.2.1, mask 255.255.255.0 (gateway and DNS are blank or 0.0.0.0)
  • cRIO set to use for the link speed autonegotiation (no option to change this) and detection of packets = "interrupt".
  • PC value link autonegotiation speed, but has no effect on the problem, if it is set on a fixed, low speed for example. Half-Duplex 10 Mbps
  • PC Firewall is configured to allow the port 3580, and actually disable the firewall altogether change the problem

  Had the chance to try again with my intermittent connection to cRIO, and here's what I found:

  • Connection through a switch, rather than directly with crossover cable - made no difference, still kept disconnecting after 3-4 minutes
  • With no other network on my laptop other than the LAN - no difference development
  • cRIO with APP No. dip switch select IT - no difference
  • cRIO with game of dip-switch SAFE MODE - this time it is remained connected, but this mode is not very useful as a solution

  Then I was reinstalling the software cRIO as suggested - it did not complete the first time, but second attempt was beautiful and connection is now very stable (and has not abandoned in the last 30 minutes).

  Here are the instructions to reinstall (just in case useful for others):

  1. In the measurement and Automation Explorer (MAX), access remote systems | cRIO | Software
  2. Click on the "Add/Remove software", and an installation wizard will appear
  3. With currently installed version of the selected software - "then click to reinstall the software currently installed.
  4. Follow the rest of the instructions, and it should take about 4-5 minutes

  Thanks for your help

  Andy

• Unable to connect to starter kit 2.0 Robotics

  Hi all

  I know this question has been askedmultiple times, and I read trough forum messages, but cannot find a solution.

  When I try to run a robotics project on DaNI, 2.0 Starter kit, I get a message of conflict resolution, saying "unable to connect to the target. --> See image rasthaus

  I installed the latest version of labview, robotics, FPGA modules and in real time as well as pilots of RIO.

  Once I disabled my firewall, I was able to detect the robot with MAX, but I was not even able to connect using labview.

  Thanks for any help,

  MortZxD

  Hello

  I had the same IP address as illustrated by MAX in my library of projects, but I could not always connect.

  I reset the IP address of the robot to start in safe mode and changing an address IP static, dynamic and who did the tour!

  Thnks

• Error: [REP_55102] unable to connect to the service of filing [BIA_RS]

  Hi all
  
  I get this error "[REP_55102] unable to connect to the repository service [BIA_RS]" when I tried to connect to Informatica Repository Manager client to server Informatica which is insallted in another machine. When I checked the log "pmreplib.log" file, it says "ERROR: REP_51147 [Mon Feb 04 15:21:11 2013]: (7216 |)» 7680) cannot connect to the repository on the host: oracle2go, Port: 6013. ».
  
  In the background, as Informatica Server is installed in another machine, we have limits to access the ports. This is why I changed all default Informatica ports by running the below command...
  ./infasetup.sh UpdateGatewayNode-asp 5503 of na oracle2go:5501 - ap 5502 - sp - 5504 - sv 5505
  
  Although I changed ports to 5501 and 5502, 5503, 5504, 5505. I don't know why the client uses port 6013 and I don't know where this port number is coming.
  Could you get it someone please let me know how can I change this port (6013), so that I can connect the Informatica customer.
  
  Thank you
  Harish Nunn

  Hi Harish,

  On the Client Informatica Repository Manager Gateway numbers and the port are provided to connect to the repository server that runs on the given gateway and port. In your case, my understanding was that the Informatica repository is running on the 5501.

  So I think that you did not change to the port number in the administration console Informatica. So in Informatica Adminconsole node configurations change the port number to 60xx 50xx. There are 2 entrances to the repository server and the numbers of ports of the max and min of Integration Services. Once you change them restart the Services of Informatica.

  Let me know if it worked.

  Kind regards
  Jay

• Unable to connect to app store after iOS iphone 10 6 update

  Hello

  Since the upgrade to IOS 10 my iPhone 6 with stubbornly refuses to connect to the App store. The error message is "unable to connect to the app store, try again."

  The phone is connected to the internet (I can surf and send emails) by wifi. Turn off the wifi and the use of mobile (cellular) only link cause the same error. I also did a reboot hot and cold, without result.

  Any suggestions?

  Thank you

  Bill...

  ANSWER: this theme has the best 3 options. In my case, I had to sign out and in the app store of settings, iTunes and app store. Fixed

  PLE-3598048 http://www.Macworld.co.uk/How-to/iPhone/What-do-If-You-cant-connect-App-Store-AP.

• Just updated to IOS 10.0.2 and unable to connect using Store.Please App!

  Just updated to IOS 10.0.2 and unable to connect using Store.Please App!

  Harry

  Hello

  Go down to itunes apple ID page homepage remove ID, then reconnect again.

  See you soon

  Brian

• Unable to connect on the Messages or FaceTime after upgrading to Sierra

  Good afternoon! After upgrading my MacBook Pro (13-inch, mid 2010) to macOS Sierra (10.12.), I am unable to connect to Messages or FaceTime. They worked fine before the upgrade.

  • Messages: After entering my Apple ID and password, I get the message "Could not sign in iMessage." "Could not sign. Please check your network connection and try again. "or"an error has occurred during authentication. "My network is connected to the network (where this message), and the password is correct. Also, I have generated a password app specific to Messages. Enter just grew the message "your Apple ID or the password is incorrect." Messages is works well with my Google Talk and AIM accounts.
  • FaceTime: After entering my Apple ID and password, the engine just turns and it never connects me. Similarly, I have generated a password app specific but use it just gets the message, "your Apple ID or the password is incorrect."

  No idea how I can regain access to these applications? Thank you!

  Reached out to the Twitter account of Apple Support. He proposed to restart. It worked.

• Unable to connect to my yahoo home page after updating iOS

  Unable to connect to my yahoo home page after updating iOS 10

  Hello. Have you tried to remove data from the site under settings > Safari? Could you describe the problem a little more in detail? What happens when you go to the site? You get a login screen? It takes your input?

• Unable to connect to State Bank Anywhere App on my IPhone 6 + after upgrade to IOS 10

  Unable to connect to State Bank Anywhere App for my IPhone 6 + after upgrade to IOS10. Tried uninstalling and reinstalling, but to no avail.

  Contact the developer of the app. They probably need to update the application to ensure compatibility with iOS 10

• Unable to connect to Airport Extreme after updating iOS 10

  Hey guys.

  OK not sure if anyone else has this problem, but I can't connect to my Airport Extreme update IOS 10 my wife is.

  We all have two iPhone 6 and 64 gb & update at the same time.

  We have an ac 802.11 Airport extreme also an extreme dual band of airport & an express airport which none of us can connect to.

  We can connect to the Home Hub 6 provided by our service provider broadband with no problems but it is only in a part of the House that we are unable to connect to my office or at the back of the House.

  Tried resetting the network settings on the phone thought I might ask before having to try to reset back to factory settings base stations.

  Thank you

  FWIW, I upgraded my iPhone SE 5 and Pro iPad to iOS 10 as well, but knows me not any problems connecting to one of my base station AirPort to Wi - Fi.

  Or the other of your iPhones must all problems connecting to other networks in addition to the Home Hub Wi - Fi? In other words, are they only having problems connecting to your AirPort base station? If Yes, do you have someone nearby who also has an AirPort wireless network that you should check your iPhones with?

  In the meantime, let's take a look at the current configuration of your network. We know that you, at least, three airport base stations. What is the exact models of non - 802.11ac extreme and Express?

  These base stations are all linked back to the Home Hub with Ethernet they are all configured for a mobile network?

• Unable to connect to the App Store since the upgrade to IOS 10

  Tried to restart App Store and phone. changed the password and recorded out and back in but still unable to connect. We will, get apps but when I try and download it keeps asking for the password and say that it can not connect. Someone at - it advice?

  Hello CT05,.

  Please ask for assistance with the App Store here in Apple Support communities. I understand how it is important to be able to download my new or existing applications on the App Store. Please try these things to see if we can get this to work for you as expected!

  The first thing we want to make sure is that all your data is safe. You can perform a backup to iCloud or iTunes. Use this article to help with this: backing up your iPhone, iPad, and iPod touch.

  Once you have your backup, please go to appleid.apple.com on your computer or via a web browser. Log in with the Apple ID you are trying to connect to the App Store with. If it connects, take note of the Apple ID and password. Try the same information on the iPhone.

  If this still does not work on the iPhone, please click Settings > Wi - Fi and turn Wi - Fi off. See if you can access the App Store on your cell data. If you can, it means that it some security on the wireless network that you are connected to that is blocking your connection. You won't be able to do this unless you use your cellular data or move you to a new wireless network.

  If you are not able to access the App Store on cellular or wireless data, please open this help article: If your iPhone, iPad or iPod touch connects to a Wi-Fi network. Check the section still not 'connect?' and look at the instructions to reset the network settings. What this does is actually reset some of your default network settings. You have to reenter your password to connect to wireless networks once this is done. Try again.

  Thanks again and have a great rest of your day.

• Unable to connect to the App/iTune stores

  Since the 10 update on my iPhone iOS 6s; When I try to open the App Store or iTunes Store, it says "unable to connect".  If I'm real quick when I open the App Store I can successfully hit a button update B4 I get the Error Message.  It tries to open the iTunes store when I try; but without success.  Everything works fine on our iPhone 5 s and my Mac.

  Ok..

  Try here > If you can not connect to the iTunes Store - Apple Support