Unable to connect to L7580 on wireless network

Similar Questions

• Satellite Pro 6100: unable to connect to internet via wireless network

  Have had some problems with the audio device Yamaha for another thread, which now seems to be resolved. Thank you!

  However, do not know why, but now unable to connect to the internet via a wireless network, although the router works well as another computer in the House is connected wireless.

  When you check the available wireless networks it comes up with "no wireless networks were found in range, make sure that your computer's wireless switch is on.
  Where to check it, can anyone help?

  Thank you

  On the left side, there is WLAN switch. Make sure that the switch is in on IT. After doing this using FN + F8 key combination and activate WLAN device.

  After having done that, you should be able to see the WLAN networks available in your area.

• Satellite A300 - unable to connect to a local wireless network

  Hello

  I have a question: bought a laptop two days ago, the wireless LAN doesn't work. It can detect the network, accepts the network key, he just used to connect.

  Help, please.

  Hello!

  Have you checked the TCP/IP of the WLAN card settings?
  I put t know the network configuration of the router, but if you are using DHCP you must use this mode or you set a static IP address.
  Check it!

  Also, check if your wireless network card is recognized correctly in Device Manager and try to reset your router. This means that you must remove the router AC adapter and wait 5 minutes. Then plug the AC/DC adapter again.
  Sometimes a firmware update might be useful too.

  Good bye

• Unable to connect to ground or wireless network

  I can't connect to my land or wireless network.  I tried to connect through my laptop to work and land / wireless worked as expected (e.g. problem is not with the router).  Previously, I was able to connect to the network via my computer at home.  Some information:

  1. I get the following message when I consult my network connections:

  "Connection status: unknown.

  The dependency service or group was able to start. »

  2 Windows cannot find any wireless networks in range.

  3. I tried to use Windows Network Diagnostics and the message I got was "The Windows Wireless Service is not running on this computer."  I tried to start the service, but couldn't.

  I would appreciate any you can give troubleshooting tips!  Thank you.

  Hi Kelly1986,

  1. what happens when you try to connect by using wired connection?
  2. do you have security software installed on the computer?
  3. did you of recent changes on the computer?
  4. What is the error message when the service started?

  First of all, I would say that check you what happens when you connect using the wired connection.

  Check also in mode safe mode with Networking if you are able to connect to internet using wired connection.

  Steps to start in safe mode with networking
  1 restart your computer if it is running.
  2. press the F8 key after your initially on powers computer.
  3. Once you see the menu Advanced Startup Options , you can stop tapping.
  4. use the up/down arrow keys to highlight your selection.
  5. Select Safe Mode with network and pressenter.
  6. you should see loading drivers and wait please.
  7. you should then be at the Welcome screen.
  8. connect to your computer using an account with administrator privileges.

  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Restart the computer to return to normal mode

  Disable the security software on the computer and try to start the service and check.

  Important: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  If you still cannot start the try running SFC scan service that would have a search system files corrupted on the computer and replace them.

  For more information please visit the link below.
  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  Solve problems, find wireless networks
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  The problems of Internet connection
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Go back with the results!

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to connect to a specific wireless network

  I'm currently sitting in a café, connected to their wifi WPA2 with my MacBook.

  I can not connect to the same network with my iPhone 4S. It just do not see it--other networks, Yes, but not the coffee. I tried to reset the iPhone; the other networks still appear, but not the one I want to join. I tried to connect manually several times with 'other '.... ', using my MacBook to check SSID and password of the wifi, but the iPhone says that it cannot find the network let alone accede.

  It's a signal very strong: the wifi bars are entirely black in the menu bar of my MacBook. My iPhone can see half a dozen other wifi networks, including those where the router is not as tight as one that I am trying to connect. I can not not connect to others: either they are password protected, or require a customer relationship or are not worthy of trust.

  What is going on?

  Just to add: I know that the standard Apple FAQ on connectivity issues iOS wifi; they are not a help here.

• locked settings by the adiministrator system and unable to connect with the new wireless network

  I changed my ISP and routers.  I need to change the settings to the new router wireless.  However, when I try to access the network settings on the printer through the screen on the printer, it is said that it is locked by the system administrator.  I am the admin.  Where can I access it without being on the network?  I tried to reset to the default values of factpry, but the same problem exists; It is blocked by the system administrator.

  I was able to solve the problem.  I went through the set up using the USB cord.  Then I switched it to wireless technology.

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Recently installed vista update. I can no longer connect to my home wireless network.

  Recently installed vista update.  I can no longer connect to my home wireless network.  I get a message that says 'wireless link failed because windows did not receive response from the access point or wireless router.  I troubleshott he said of computing could be from low signal strength and yet it shows the strength of 100%.  Anyone have any ideas?

  Hello

  Check the firewall it is maybe it has been reset.

  In general.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Connecting to the wrong wireless network.

  Nope.  Tried to make this process a few times just to make sure that I was just doing and still it connects to the wrong network.  Something else I could try?

  I'm in the boat the same, did you ever get a resolution on this?

  Separated from the<>https://answers.microsoft.com/en-us/windows/forum/windows_7-networking/connecting-to-the-wrong-wireless-network/633fcfd6-7bdd-4369-b66f-94611c5df76e >

  Here are some solutions to try if you can't connect to Wi - Fi. Follow the below mentioned steps to solve the problem:
  1 remove the network and let Windows re - find. Then enter the password again.
  http://Windows.Microsoft.com/en-in/Windows-8/get-online-tutorial
  2. change the TCP/IP settings, if the IP address is set to manual
  http://Windows.Microsoft.com/en-in/Windows/change-TCP-IP-settings#1TC=Windows-7
  3. If none of the above steps work, follow the link to solve the problem below:
  http://Windows.Microsoft.com/en-in/Windows/cant-connect-to-network#1TC=Windows-8

• Pavilion Elite e9290f: need to connect to a home wireless network

  We had bought our PC for several years and had it connected to a router to access the internet.  I think that the computer has the feature to connect to a wireless network, but you should never use this feature.  We moved recently, and now we are in a situation where we are unable to connect the PC to the router.   I'm not sure how to proceed.  I don't see that a WLAN listed in Device Manager.  We are running windows 10.  any guidance would be appreciated.

  Kaalee75, welcome to the forum.

  The computer has a wireless interface card:

  Figure: Wireless card - side view (version embedded antenna

• I am unable to connect to my router wirelessly to parents. I tried to reset the modem and the router and it still does not work.

  Presented labtop parents and can connect via ethernet, but still cannot connect to the wireless router. Ive rebooted both the modem and the router and ive also unplugged the power source. Help, please...

  original title: unable to connect to the wireless router?

  Hi Brandon,.

  What operating system do you use? (Windows 7, Vista, XP?)
  You receive any type of error message when you try to connect?
  What exactly happens when you try to connect?
  You receive an internet connection when you connect with an Ethernet cable?
  There are a few good troubleshooting in this thread. I suggest to look to see if it helps at all:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/unable-to-connect-to-a-wireless-network-Windows-7/734ecdef-99fb-4862-b63a-04cfa448cc06

• HP OfficeJet Pro 8610: Printer cannot connect to the new wireless network

  I got the OfficeJet Pro for a while and everything worked very well (including wireless printing from my Mac and iPad AirPrint). Yesterday, we got a new Modem Router (from Ubee). As I tried to connect the printer with the new network, I fail miserably.

  Here's what I've tried several times: on the small screen of the printer, I select: Network Setup > wireless setting > Wireless Setup wizzard. The printer seems to networks, find the network and asks me the password, I get the password (I did this several times, so no typos!). The printer then "trying to connect to the network"... then it crashes: for a very short moment, I get a blue screen with a white error code (not always the same, for example.) B3FF3802) and then the message "error in the printer, turn off the power, then press.

  I turned off the printer and turn it back on several times (incl. pulling out the power plug and restart after a while), but when I go through the steps above, but I just get the same endresult.

  I deleted the old network as I feared it might interfere with the creation of the new network. No noticeable effect.

  I printed the "results of the wireless network test," which confirms that "your HP printer is unable to connect to your wireless router. In the results of the diagnosis, he states that 'network name (SSID) was found - Fail.

  I quite understand the message that the printer detects the network and shows good SSID / network name. I thought to enter the SSID manually but can't find where I could do.

  I'd be very grateful for any suggestions on what could be the problem (I can't imagine that the printer would not work with a new router... I searched the internet and found stuff on 'Hello compatibility', but do not know which is the issue I'm facing.

  Thanks for your help!

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.

  If you are unfamiliar with the operation of the function of private messages of the Forum, this post has instructions.

• HP spectrum 13 Ultrabook: Unable to connect at 5 GHz wireless

  Hello

  Is it possible for this ultrabook, the product F4A22PA number #AB4, connect to a 5 GHz wireless network? Because currently, it cannot 'see' the 5 GHz home wireless network while all my mobile devices can. Is it a hardware problem or a software problem?

  Thank you.

  Hello:

  Here is the link to the product for your laptop.

  http://support.HP.com/us-en/document/c04015688

  Next section of wireless connectivity, I see an Intel 802.11b/g/n with card Wireless Smart Connect (2 x 2) technology listed.

  Whenever you see a card with a suffix of bgn wireless, it means that it is a single card band (2.4 GHz) only.

  A dual band Wireless N card has a suffix abgn or agn.

  That is why you cannot connect to the band of 5 GHz with your laptop.  The card is only designed to connect to the 2.4 GHz band.

• Cannot connect Tecra 9000 to wireless network

  Hello

  I am trying to connect my laptop Toshiba T9000 to my BT home Hub 2.0 Wireless v but a little difficulty.
  The laptop recognizes the hub, but every time I click on connect, I get the same message.

  ""Windows cannot connect to the selected network. " The network can be is no longer in range. Please refresh the list of available networks and try to connect again"

  I went through a few troubleshooting steps to resolve this problem, but always without success.
  Can I update the driver? My inclination is that this may have something to do with the laptop is not able to support WPA?

  I am not very computer but if anyone has any additional input to help me with this question then I would be very happy.

  Kind regards
  Answer by quoting

  > Can I update the driver? My inclination is that this may have something to do with the laptop is not able to support WPA?
  This may be possible

  The point is that this laptop is an oldie and the wireless network adapter appears to be old too.
  I ve no idea what WLan card you have, but you could try to connect to the WLan without use of encryption settings. Disable encryption on the router Wlan and test connectivity again. of course, this must be done only for testing purposes
  The wireless network must be always secure

  The alternative could be the use of external USB WLAN, it would be the easiest and fastest way for that to be resolved

• HP DESKJET 2540: My HP printer connects to the wrong wireless network

  Hello

  I use a MacBook Pro, OS X 10.9

  I have a printer HP DESKJET 2540

  I just installed a new network at my place. I'm trying to connect my printer to this new network wirelessly via WIFI.

  BUT the printer keeps on connecting to the previous network, which is an open access network (FreeWIFI)

  I've tried EVERYTHING. I pressed simultaneously the Wireless button and the button to launch the copy in black. The wirelss test report shows that my printer is currently always logged the previous SSID

  Help, please!

  TX

  Hi @JACE1,

  Welcome to the HP Forums!

  I understand that your HP Deskjet 2540 guard wrong wireless network connection. I'm happy to look into this problem of connectivity for you!

  On the wireless test report, must be an IP address from the printer. Try putting the IP address in a web browser, such as: Safari or Firefox, etc. You should see a built-in Web server. Find the network tab and then select it. Then, look for the wireless configuration wizard option. (This should be able to search for the network wireless appropriate for you).

  See page 55 of the User Guidefor more details your printer.

  Hope this solves your problem and have a nice day!

  "Please click the Thumbs up icon below to thank me for having responded."