Unable to connect to my new router cable, my XP and Windows 7 machines

Similar Questions

• Unable to connect TV to new router

  KDL-46HX820. In the process of setting up the TV, I properly connected by Wi - Fi on my router Linksys Valet Wi - Fi. Later, I replaced this router with a Linksys E4200. The Linksys router has generated its own network ID and password. I tried to connect the TV to the new wireless router using the WPS process, but the TV will not connect.

  What should I do to get the TV to connect to a new wireless router with a new network ID and password?

  Thanks for any help.

  Try to assign a static IP address for your TV. First of all, you need to find the address of the gateway of your wireless device. In a computer that is connected to your wireless network, you can open a command prompt window (start - run - cmd) and type ipconfig. This will give you the address of the gateway (for ex: 178.152.1.1)

  Then go to the TV and go through the configuration of the network (wireless).
  When you configure IP address and proxy, choose (custom instead of Auto).

  Then proceed as follows:
  IP address: 178.152.1.15
  Address of subnet 255.255.255.0
  Default gateway 178.152.1.1
  Primary DNS 8.8.8.8
  Secondary DNS 4.2.2.2

  Note that the IP address and default gateway is the same as your gateway address you got from the computer except the last figure of the IP address.

  Then browse the rest of the setp upwards and who need to connect to your wireless router

• Unable to connect to the internet with the NETWORK card and Windows Millennium Edition.

  Hello

  I turned on my old computer yesterday, who has installed Windows Millennium Edition. At the back of the computer is an Ethernet port which is marked as LIEN ACT. The NIC with this port is Realtek 8139 PCI Fast Internet Adapter. I spend two hours on the Internet configuration and I did and finally got connected, but then, a few hours after, something went wrong and the Internet and the NETWORK card has stopped working! And the card has disappeared from the Device Manager, but he's still showing in network in Control Panel. I opened the computer and I reconnected it to the slot, but it did not help. At the back of the computer next to this port are two LEDs - green indicates the power that lights up when I plug the Internet cable and the other orange indicates actual connection. But now these two LEDs are not indicating something even when I plugged in the cable to the Internet, which comes from my router. In the computer a Dial Up connection PCI is installed too, but I disabled it. I used Dial-Up in 2002. So, I need help.
  But I know that I can connect with this Ethernet card to the Internet because it worked for 3 hours, I've loaded the pages and downloaded programs.
  Please don't point, should I upgrade Windows!
  Thank you.

  Hi friend,
  You can try a Bing search on connectivity to Win ME, I don't know there are still a few old sites that are not taken down you will find a few FAQ on.
  I saw not a ME machine in too many years to count!
  Good luck on your adventure.
  B Eddie

• Unable to connect to the internet after the system restore and Windows Installer (Vista)

  Hello

  I have recently restored the whole system on the HP to my sister a virus that I was unable to remove it manually.
  The system restore went well until it has reached the point where he was going to reinstall Windows. The computer just turned itself off and the software installation was not complete. I am able to reinstall again. I must therefore hold the CTRL + alt + delete, go to Task Manager, click on audit.exe and complete the process to turn on the computer. But I can't do anything with it in safe mode. The main problem is: I can't connect to the internet! Even if the network discovery is on it will not find my wireless network. What can I do on the internet? And is it possible to install Windows again without the CD?
  Thanks in advance!

  Hello

  ·        You are able to boot to the desktop in normal mode? If this isn't the case, then you get any code or message?

  ·        How did you did system restore?

  ·        Are you referring to the system recovery using the recovery partition or the drive?

  I suggest that you start in safe mode with network and check if you can access the internet?

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Note: select SafeMode with networking among the startup options.

  Respond with the required information so that we can help you further.

• Impossible Windows 7 computer upstairs to connect to a new router that I just installed. It worked fine before.

  I changed ISP and changed my wireless routers. My computer laptop windows 7 connects perfectly, no problem. Cannot connect my desktop computer which is on the floor. IF I take my laptop it it works fine. I changed the settings secure to unsecured and it connected correctly. When I changed this back in would not work again.
  It says that windows is unable to connect to my router. I have reset my modem and router and it continues to happen... What can I do?

  original title: unable to connect to the wireless router.

  Hello

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet.

  Connected to the new router, but locally only.

  Currently, I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet. The small icon to the left of my screen says only: ACCESS: LOCAL ONLY.
  BASICALLY,.

  I have Windows Vista Home Premium, notebook Compaq (Presario CQ60 to be exact)

  I can connect if I use a cable, but its disadvantages.

  I can connect wirelessly with my PC and Ipad. and Internet access.

  I TRIED:
  Various patches microsoft such as resetting TCP, safe mode with network, reset the router. »

  Thank you in advance and we hope you can answer this soon!

  I use an Atheros AR5007 802. 11 b / g WiFi Adapter(Compaq laptop) for the moment so this is useful. Thanks again!
  Someone suggested that I update my wireless driver. I am open to this idea, if anyone can find a safe and legal site with the download.

  Hi Bryyaan11,

  You can check out the link to HP support and try to download the drivers for your wireless card updated:

  Support HP & drivers

  For more information, you can also consult the following article:

  Updated a hardware driver that is not working properly

  You can also check the following items and try the steps:

  Windows wireless and wired network connection problems

  Solve problems, find wireless networks

  Hope this information is useful.

• OfficeJet 6600 e-all-in-one: Wireless connectivity with the new router problem

  We had the printer since 12 months, workin with no problems.

  Just got a new modem/router (NETGEAR V7610) installed as part of the NBN implementation and I can't get the printer to connect to the new router. 5 and 2.4 G active networks. The two defined newtorks on security WPA2-PSK [AES].

  The printer detects the wireless (2. 4 g) network, but can't coplete the connection. Tried the two direct input the network key and using WMA.

  -The display panel shows "wireless invalid password (WPA) is entered.

  -The results of network printer test page indicates a FAILURE on safety.

  I was able to connect to multiple other devices (laptop, iphone, Kindle...) without any problem. Used the two direct entry of the key network and WMA.

  Anything else I can try?

  Find a new update of the firmware for the printer (May 9, 2016).

  After you apply the update, the printer is able to connect to the new modem.

• I have an Adobe Creative account and my payments come out every month; However, I am unable to connect with my new account or access programs I have installed; It only let's login me under my old account. Can someone help me solve this problem?

  I have an Adobe Creative account and my payments come out every month; However, I am unable to connect with my new account or access programs I have installed; It only let's login me under my old account. Can someone help me solve this problem?

  Hello

  I see that you have an adobe account with the same email with forums, however, I don't see no subscription under this account.

  If you can't change the email during indexing, see the steps below:

  The OOBE and rename it OOBE.old and then try to connect with the correct ID:

  Location: -.

  Windows C: \ directory users\ user account-App data-local-adobe \oobe

  MAC: Go / go to the folder / Application support / Adobe / oobe

  If nothing helps, please contact adobe support:

  Contact the customer service

• Unable to connect to the internet by cable sony bdp s490 network

  I have sony bdp s490 bluray player iam unable to connect to the internet by cable network

  my internet broadband requires the user name and password when using on the pc where should I apply the username and password when the internet connection for Blu - Ray player

  
  

• Under the option bookmark organizing appears no bookmarks, new computer Firefox 4.0 and Windows 7, how to show, thank you

  Under the option bookmark organizing appears no bookmarks, new computer Firefox 4.0 and Windows 7, how to show, thank you

  "Organize bookmarks" has been renamed to "show all bookmarks" in the bookmarks menu.

• HP Deskjet 3510: Cannot connect wireless with new router

  I got a new modem with router wireless integrated into my cable company.  Now, I am unable to connect wirelessly to my printer. He seems incapable of finding new wireless information.  The closest I could get the printer screen advised to 'hold the WPS button. '  However, my cable company has confirmed that the WPS NO button there and is not an option.

  Can someone help me get my printer working again?  Thank you!!

  @LisaC11

  Printer:

  E-all-in-one printer, HP Deskjet 3510 range

  Full software features:

  File name: DJ3510_1315 - 1.exe

• Problem connecting to the new router

  When we all first our WVC54GC Setup was quick and easy, and we used it without event for 1-2 years. Now, we have replaced our old router with a WRT610N. Everything else, wired and wireless, connected to the new network without event after I have updated their SSID settings and security. (A new uses WPA - WP2, the an old WEP) but for this camera I can not to do. I read the articles on this page and plugged all the correct settings, but it still won't talk of it in wireless mode. (With a cable that is no problem). What I'm missing here?

  You must be identical on both devices wireless settings to establish communication between your router and the camera... Ensure that your camera settings Wireless 2.4 GHz of your router... Try Basic WEP security and see if that works, if WEP works you can change security to WPA... Once you have set matching the wireless settings, unplug the cable ethernet and power cycle the two devices and see if you can see your wireless camera...

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• 3050 printer all-in-one - connects to the new router?

  Hello

  I just got a new router installed and since can't get my Deskjet 3050 to a wireless connection.

  I tried to go into the router setting and adding via pin and WPS button but no work

  I tried the part configuration of the HP set up in my Mac, but only crashed every time so I uninstalled the printer and re downloaded. However he now does not have as an Application, but I can still select in sub printers, but can only print via cable Wi - Fi and not

  Help - very frustrated

  Thank you

  It's weird.  Try disconnecting the power to the printer without turning off first.  Unplug the unit from the rear of the printer and omit the cable for 30 seconds.

• Unable to connect to the WLAN router satellite P300

  Hello everyone,

  I hope you can help me with my problem.

  I bought a Satellite P300. Now, I'll have some connection problems to my fritzboxfonwlan over a wlan network.

  When I connect my laptop via a cable, all right. Only with wlan i´m problems.
  My router ssid is displayed correctly. I can also type the key. But then the router is not to be found.

  I use as wpa2 encryption.
  I think that Vista has problems with it. Vista has also the most recent updates and my wireless (intel agn5100) card.
  I tried all the three drivers on the side of toshiba. I Don t know what I can do next.

  If you have any ideas, I'll be happy to hear it.

  Hello

  Have you checked if the address Mac filtering settings can affect the WLan functionality?
  If the MAC address filtering enabled your WLan card mac address has been inserted, then your laptop wouldn't connect.

  Also I recommend you check the settings of the WLan card TCP/IP.
  In the TCP/IP properties, you must set options for automatically

  PS: have you checked whether your P300 is the latest BIOS?