Unable to connect to my router satellite U505

Similar Questions

• EA6700 - Unable to connect to your router SmartWifi

  Hello. I managed to connect to linksyssmartwifi.com, but still get this error trying to connect to my router outside LAN.

  Linksys Smart Wi-Fi was unable to connect to your router. This can occur if the router doesn't have Internet connectivity. Try to access the router again later, and if the issue persists, troubleshoot your router's Internet connection.
  

  I know that the router is online for you (can connect Wan) and I confirmed the email account during installation.

  Any help is appreciated. Thank you!

  Oops! Turns out that I do not have remote access on when setting up. EU local network connection using the account LinksysSmartWifi.

  http://KB.Linksys.com/Linksys/UKP.aspx?pid=80&VW=1&articleid=25854

• EA6500 unable to connect to the router after Time Machine

  Just got an EA6500 - updated to the latest firmware available.

  I have attached 2 x WD NAS and 1 x WD through the USB port of the device.

  Each time after I finished running Time Machine on the MacBookPro (written to one of the WD NAS), I can no more connection to the router as neither the local IP, or the cisco connect cloud. The error message I get (loosely formulated) is: unable to connect to the router. Please ensure that the router is connected to the internet.

  At this point, all the devices connected to the router (wired and wireless) still can access Internet perfectly. Only the console of the router is therefore more accessible.

  Anyone else have the issue?

  Any ideas on how to solve it?

  Contact support for Cisco and the person advised me to do a factory reset (even if the router is new with no customization!). Regardless, it now works correctly. Cisco Cloud Connect works always before, during, and after a Time Machine.

  "When in doubt, try to turn the grid and the.

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Unable to connect to the router WLan - Satellite L300D

  Please help me so that I have still a few hairs left!

  I installed WLAN driver on my laptop Satellite L300D with Vista Home installed.

  I see my network in the available connections, but when I go to connect, it will not connect.

  My other two desktop computers can connect to the router without a problem.

  Any suggestions?

  Thank you
  Neil

  Hello

  I think that you didn t try updates. Right?
  Therefore, my first recommendation would be an update of the BIOS and driver WLan.

  Check the current version of the BIOS that is available on your laptop. If the latest version has been released then update the BIOS.
  In addition, to download the latest WLan driver from the Toshiba WLan portal and to update:
  http://APS2.toshiba-tro.de/WLAN/

  On this Wlan site, you will find three different WLan drivers for three types of WLan cards. First check your wireless network card, and then use the right driver!

  See you soon

• Satellite A300 - unable to connect to my router

  Hi all

  I have a Satellite A300 and a Satellite A300D. Since a year im dealing with a problem and eat my heart. I have problems to connect to my router, for the moment I have a Netgear ADSL modem router wireless. When I am looking for a wireless network it seems to find the network, but when I want to connect I get the message network is no longer in the area.

  The distance between my modem and laptops are 3 meters in an apartment, even when im sitting on my router :-) this is not not possible to connect to the wlan. Tried to connect without any wep/wpa encryption, no effect. Played with communication channels @ the properties of the wireless network adapter and the router, but this isn't a solution.

  Before I got the Netgear, I had a Linksys / Sweex / Cisco pro / router Wlan from HP. I tried all brands of wlan, with all routers routers of this I had the same problem.

  Frustrating him of is that I can connect to my neighbors without any problem, but not my own network.

  Anyone having the same problem or know a solution?

  Have you tried to update the WLAN driver on two laptops? You can find it on the Toshiba site and I would update the BIOS too:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  What operating system do you use? If you use Vista, you must disable the WLAN to save energy card. You can do it in Vista Power Options.

  You use the same standard WiFi on your laptop as on the router? For example I mean project. G check this!

  At the moment it is not easy to say what is the reason for this, but I hope that I could help you a little. :)

• Satellite L300 - unable to connect to my router

  Hi guys,.

  I got this laptop a few days ago, everything works as it is supposed to be except for one thing, I try to connect to my wireless internet signal and it picks up the signal itself as a strong signal, but when I go to enter my WEP it never connects. I can't actually connect to the signal.

  I have another laptop which I can easily connect to my wireless signal.

  I have a wireless cable modem so it Wouldnat be my internet service,.

  Someone at - it ideas? Purchase of an additional Wi - fi adapter would work instead of using the built in Wi - fi? Also, the laptop came with Vista Home Basic installed.

  Any help would be greatly appreciated.

  Thank you guys.

  Hello

  Can you connect to the router, if you disable WEP encryption?
  In addition, WEP encryption is not safe and can be cracked in a few minutes, then you should choose another encryption WPA or WPA2.

  In addition, I would recommend updating the driver WLAN. On the Toshiba site, you can find the most recent version.

  What OS do you have? If you have Vista try disabling the WLAN card feature in Vista Power Management for energy savings.

  Good luck!

• Unable to connect to the router

  -Please ignore this message: I did not wait enough to do the factory reset. It seems that launch a factory reset without waiting for 10 seconds only restarts the router.

  Hello

  Today I tried to connect to my router (I do not use it for a few years) and it didn't work at all.

  Initially, I plugged it in just 2 RJ45 cables: one for internet, one for the PC. The computer could not connect to the router (DHCP failed).

  I then restored the factory settings and tried again: same thing, the computer could not find the router via DHCP.

  I tried to force an IP address (IP: 192.168.1.5, mask: 255.255.255.0 Gateway: 192.168.1.1).

  By forcing the INVESTIGATION period, I was able to connect to the router, but when I tried connect to 192.168.1.1 with admin/password, it wouldn't let me (bad password - don't forget I restored it to factory settings, several times actually). The address http://routeurlogin.net/ is not found (404) and I was unable to go on websites (404). A curious thing is, using this connection, I was able to connect to Skype (and send/receive messages), although the sites Web could not be reached from a browser.

  I'm running out of ideas to solve the problem, but I suspect a hardware problem, so any help would be welcome.

  Yes he did.

  I couldn't find an option to delete my message, otherwise I would have done it.

• I am unable to connect to my router wirelessly to parents. I tried to reset the modem and the router and it still does not work.

  Presented labtop parents and can connect via ethernet, but still cannot connect to the wireless router. Ive rebooted both the modem and the router and ive also unplugged the power source. Help, please...

  original title: unable to connect to the wireless router?

  Hi Brandon,.

  What operating system do you use? (Windows 7, Vista, XP?)
  You receive any type of error message when you try to connect?
  What exactly happens when you try to connect?
  You receive an internet connection when you connect with an Ethernet cable?
  There are a few good troubleshooting in this thread. I suggest to look to see if it helps at all:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/unable-to-connect-to-a-wireless-network-Windows-7/734ecdef-99fb-4862-b63a-04cfa448cc06

• Unable to connect to the router with windows 7?

  I have just bought an Acer Revo R3700 and installed Windows 7 above, but I can't connect to my router.

  My router is heaven and successfully has 4 laptops (both under Vista, two 7 running), an Xbox and a Wii and two smartphones connected to him. Yet I just can't do this system to connect to him.

  I'm at my wits end... I've tried absolutely everything. I searched the Microsoft answers site found several similar problems and tried a lot of solutions, including adding files in the registry and update drivers.

  At first I could connect to the internet every now and then, but it was biblically slow (I tried to download Google Chrome and got him to 0.2 Kbps) and soon disconnected. Now I can't connect at all.

  I just downloaded a the Ethernet controller driver and updated a driver WLAN as they apparently do not come with Windows, but it still doesn't work. Although the message has now changed to "Unable to connect" to "Limited connectivity" (even though I think it's more coincidence than anything else)

  It should not be a question of signal strength, like the Xbox and laptop computers work fine when placed next to her.

  Really needed a solution to what running an ethernet cable is not really an option :(

  Thanks in advance guys. I'll be happy to provide any additional details if you need it :-)

  EDIT: / / I would add that I seem to be able to connect fine with a phone as a hotspot? It is very very weird.

  EDIT: / / I just managed to connect, but its very slow and not changed anything for the last 100 times? Everything seems to be completely random when it let me? : S

  Hardware support comes equipment - including the drivers/software manufacturers to use such software in all operating systems.

  Looks like a possibly faulty hardware or shotty (the wireless network device.  Make and model)?

• Re: Wireless not connect / search for router - Satellite P305

  Hey all, I hope that I can help.

  As I come back from uni, my laptop has decided that its wireless won't work. When I scan, it cannot find the router in my house and the icon in the taskbar has a cross inside. When I plug my laptop into the router via ethernet, it connects very well then and the wireless takes over even the router, but as soon as I unplug the wireless dies again.

  My laptop is a Toshiba P305 and has an Atheros AR9281 wireless card.
  My OS is Windows Vista Home Premium 32 bit SP1.

  I know that's not the router, since everything else connects fine - my PS3, this old PC XP (so I do this thread), etc.

  Sometimes when I start the laptop it finds my router (and a neighbor), but when I try to connect to it it says "Windows cannot connect to this network" and it simply disappears. Also sometimes I can connect to the router after that the Ethernet cable is disconnected, but it is limited to the connectivity (i.e. I can't get on the internet) and soon the tomb with the message "Windows has not received a response from the access point or router" and can not find yet

  What I've tried so far.

  -Restart.
  -Leave the portable island for awhile.
  -Switch wireless switch and turn it back on.
  -Check I have the latest drivers for the card.
  -Reinstall these drivers.
  -Check if the WLAN or other network services are disabled.
  -Restart some services.
  -Disabling and then re-enabling the adapter.
  -Physically sitting right next to the router and it still can't find it.
  -System restore
  -Disable the WEP encryption on my router and use another method of security, even turn off security completely.
  -Reboot the router.

  I have not had any problems with the wireless front, he has just started happening yesterday.

  Thanks for any help/advice, I'm out of ideas.

  Hello

  I see you didn't update the BIOS
  Well buddy, I think you should do this!
  Update the BIOS, and then try again

  If you notice more WLan connectivity issues then I would recommend changing the WiFi channel! This has been useful for me in the past!

  I know that you tried to update the driver WLan but check this Toshiba page for the latest version of the WLan driver!
  http://APS2.toshiba-tro.de/WLAN/

• Unable to connect to the router (even after reset)

  I'm really frustrated, and I hope that this community can provide an answer. After all the hype around this router, it is he who gave me the most trouble.

  About a month and a half... completely randomly it seems to me, I could not connect to the router more. Not through intellectual property, routerlogin.net/com...nothing. It just says: cannot display the page. I did everything I could possibly think, tried all of the suggestions I could find here and elsewhere and still nothing would work.

  I finally did a hard reset and obviously lost all my settings... and RIGHT AFTER the hard reset after upgrading the firmware, I can't connect to the router again. This could be the cause? Is there a way around it?

  The router worked fine until about a month and half ago. Then I stopped being able to connect to the admin page. Several resets hard did nothing.

  I ended up RMA'ing it and the new replacement works fine (for now).

• Equium L300 unable to connect to my router using wireless

  I have a laptop Equium L300 and can't connect to my router using the wireless option.

  I am told that the wireless feature is disabled on my pc but the switch on the front is activated.

  Can connect with the cable is the wireless.

  Anyone know what this could be?

  Try pressing Fn + F8, only the activated Wifi become?

  In Device Manager, the wireless device is reported to work ok?

  Try a BIOS update as well.

• Unable to connect to the router WUMC710

  I have a WUMC710 wireless bridge connect to a router, Asus RT-AC66U. The problem is that is no longer, it connects. The wifi LED on the front is not illuminated and in the interface web when you try to connect, it said treatment with a progress bar which is 50% and fails. It used to work fine then one day just stopped working. I tried to disable the firewall of the router, change of bandwidth and even try on another router with no luck. Can someone help with my problem? Thank you in advance.

  What wireless modes that you use on the router principal host?
  2.4 Ghz and 5 GHz routers: try Singlemode G or N or mixed G and N on 2.4 Ghz and single mode N or mixed on 5 GHz?
  Width of the channel to Auto 20 / 40 Mhz or try 20 Mhz only.
  Try to set a manual channel to a channel open or unused. 1, 6 or 11. 11 for Singlemode N if the channel is clear. 13 for the regions of the EU. Try the channel 48 or 149 on 5 GHz.
  http://KB.Linksys.com/Linksys/UKP.aspx?VW=1&docid=f2625b15a5d7454b8e7fafbe65d5aa63_4009.XML&PID=80&r...

  What security mode are you using? Privilege 'egi' is WPA-Personal. WPA2 only.

  Temporarily disable WPA security and see if it connects.

  Doest he bridge connect to a 2.4 Ghz radio?

  Factory reset the bridge and set up from scratch...

  The bridge connects to a different router?

  Reset the bridge, reload the file FW, the factory reset and the whole upward from zero...

• Unable to connect to the router (BEFSR41 V4.0)

  I have a Linksys BEFSR41 (Version 4.0) wired router and I am not able to connect to it. It has been in storage (the top of a closet shelf) for the past two years and when it when it was still used it worked like a pro.

  I used the downloaded from the site Web of Linksys router configuration utility to install it, and when it gets to the final stage, he says that it cannot connect to the router. Try to go to 192.168.1.1 translates into a (very long) network timeout.

  I have reset the router several times (retained in the for more than 10 seconds reset button) and have had no result. All the lights on the front of the router work normally.

  I already checked and I'm set up to get the IP addresses of network automatically rather than assigning a static.

  Any help appreciated,
  ~ Darxide

  Number set by putting the ADSL modem in bridged Ethernet mode.