Unable to connect to storage as "different subnet."

Have just updated my LenovoEMC device to the latest version of the software (4.1.114.33421) and now get the message

"Unable to connect to the storage because it is in a different subnet.

but I can go to the Admin in the usual way, through devices and can change anything, as all the mapped drives as if it worked and all the data is visible?

Reset the system and all users etc., verified that DHCP is select rather than fixed, tried fixed without result.

Someone has an answer that works or is a reset?

Got it finally - works had to install a new version of Storage Manager - Version 1.4.8.33485

After installation, restart the PC only and ran it Storage Manager - it took forever, but she finally found my nas and created links to explore.

Can't believe that they a D A M N blip! in my previous post - AR even if you ask me.

Tags: Lenovo Products

Similar Questions

  • False warning - unable to connect to storage alarm

    Hola

    Recientementen of alerted he configurado the cannot connect to the storage of alarm, para as no. notifique cuando an ESX:

    Pierde conexion al storage: alert

    Pierde redundancia al path storage: WARNING

    Al degradation del way storage: WARNING

    We have received several weather sober varios/place, los esx to con mantienen the alert warning

    Background: gray

    New status: yellow

    Setting the alarm:

    ([Expression alarm event: connection of storage lost;]) Status = Red] OR [expression alarm event: lost storage path redundancy;] Status = Yellow] OR [expression alarm event: path of storage degraded redundancy;] Status = yellow])

    Details of the event:

    Redundancy degraded storage device naa.60060160363027000034c4d090c8e011 path. Vmhba1:C0:t0:L27 path is down. Touch of data warehouses: "VM_xxxxxxx."

    Reportadas cuando comprobamos las LUN paths, amendments seem todas los activas y sin problemas.

    Supongo as haya sido a problema puntial conexion por one of the paths, pero lo know no entiendo porque el not to 'auto-limpian"los los ESX cuando los caminos estan correctos again warnings. Se ha of hacer una config advanced Escalin alerted?

    MUCHAS gracias

    Saludos

    Hola mokymura,

    ES UN normal behavior. Compares lo mismo cuando tienes a grouping y pierdes redundancia of caminos, is is marcado con el WARNING pero los enlaces are themselves well encuentran.

    Este behavior is debe a vCenter as any you can recover el evento what indicates that ha vuelto al estado normal. Debido a esto hay do a manual reset of alarmed her.

    Tripped reset alarms of the event
    An alarm triggered by an event could not settle back to a normal state if vCenter Server does not retrieve the event that identifies the normal state. In this case, reset alarm manually to return to a normal state.

    A greeting.

  • Connect two networks with different subnets

    I have a network that is totally excluded from the rest of the network. It consists of a switch Allied Telesis AT - 8624T layer / 2M 3, a computer and a few PLC devices.

    It is the only switch Allied Telesis, the rest of our network is Cisco. Allied was by a seller.

    Our network uses a 10.10.1.X network, but this standalone network uses a 192.168.201.x. I need to connect the two networks, because a system on the network 10.10.1.x need to access the computer on the network 192.168.201.x. I wonder if I can do it with a 2960 s Cisco or if I should get a router between the two switches.

    I am pretty new to the implementation of this type of equipment, was suddenly thrown into the mix, I appreciate any help that can be offered. Thank you.

    Hello!

    You can do this with your switch 2960, they take over the static routing. Please see the following link for detailed configuration instructions:

    http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst2960/software/...

    You will not be able to perform routing inter - vlan but pointing your static routes to the other managed switch interface you will be able to achieve. BE aware that the other switch must have some sort of routing capabilities too or you will need to get a router.

    I hope this can help, greetings!

    JC

  • migrate storage fails with 'unable to connect to the host.

    I'm trying to migrate storage of a virtual machine to a different data store. (on the same san)

    When I start work, I see the task:

    Moving the virtual machine / status 'in process '.

    After 10 minutes, I get 2 pop-up windows:

    -


    Error

    -


    Unable to connect to the host.

    -


    Ok

    -


    I tried to move the storage of another virtual machine, but I got the same error.

    Also tried a different vmhost (but same cluster), but also the same error.

    When you try to a host in a different cluster, it works without problem (same san/store data used in the cluster where I got the errors)

    There is no difference in the profile of security on the host computers.

    Any tips?

    Logfile attached (vpxd - 353.log) when I was running the migrate storage.

    Part of the error:

    2009-11-03 16:49:07.035 02464 info "App" (1257263347020035) VMotion began

    2009-11-03 16:58:35.903 02464 error "App" (1257263347020035) VMotion failed: vim.fault.HostConnectFault

    When it works ok:

    2009-11-03 17:29:49.470 02456 info "App" (1257265789470153) VMotion began

    Hello.

    See KB 1010837.

    Good luck!

  • How to get iSCSI SAN connected to ESX when the SAN is on a different subnet?

    Hi all

    I have two machines ESX which are directly connected to a San that are on a different subnet other network cards.  Other network cards are 10.x.x.x and the SAN is on 172.16.x.x, however whenever I try to add the iSCSI storage, the system will never find the LUN.  I put the vmkernel 172.16.x.x but it does not always find them.  I know that the LUNS are configured correctly if its ESX just having problems with the other subnet.

    You need to activate the Service Console to see the iSCSI SAN, too. This is because you use the initiator software. For example, you can add a second SC in the vSwitch that your VMKernel Port is connected and align on the same subnet.

    Kind regards

    Gerrit Lehr

    If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

  • I'm unable to connect to a specific web site. Have you tried 3 different browsers and they all say that they are unable to connect. No one else has a problem connecting to the page.

    I tried to use www.findagrave.com for 2 days.  I tried 3 different browsers.  all say that they are unable to connect.  No one else has a problem on this page.  I have no problem to do something else.  Why, throughout this site I can not connect with?   I use it all the time in research.  very aggravating.

    original title: on a web page

    Well, I tried the support page, but I already tried all that.  I did a restore full back to factory settings... still cannot have only one page to load.  I'll call my dsl provider this afternoon.  I don't know what else to do.  I can't communicate with Findagrave.  I don't have a snail mail address but no phone number.  But I don't think that it would be them anyway, if no one else has a problem with this web site.  There must be on my end, don't you think?

    I don't know what to tell you. There is no problem, it's on your side.

    If you care to try it... on the assumption that your user account is damaged.
    Create a different user account with exactly the same type of account > connect to it and see if you can access this Web site.

    Personally, I doubt that will solve anything, since you already restored your computer to factory settings.

  • I'm unable to connect the Sony Walkman to my PC, receive error message WPD Enhanced peripheral of storage drive has a past problem cannot start [code 10].

    Original title: drive WPD Enhanced password storage has a problem cannot start [code 10]

    I tried to uninstall and install but nothing works I'm unable to connect my sony walkmann more

    It does not charge or sync with the device.

    apears there is a problem with the password for the improved wpd storage disk

    Hello
    1 did you change on your computer before this problem?
    2. What is the model of the Sony walkman?
    3. what happens when you load the device?
    4. What is the brand and model of the computer?
    WPD (Windows Mobile) devices allows computers to communicate with attached and peripheral storage media. WPD offer a flexible and robust way to computers communicate with readers of music, storage devices, mobile phones, cameras, and many other types of connected devices.
    Check if the device works fine on another computer.
    You can also follow the steps in the article mentioned below:
    Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
    http://support.Microsoft.com/kb/943104
    Post your answer for you help in this matter.
  • Unable to connect to the ftp to EA4500 usb storage device

    I am unable to connect to my hard drive on the EA4500 from a remote device (pc or mobile) using the ftp protocol.

    The drive is a WD 1 TB and is supported. I use cisco smartwifi to set it up. The player is accsessable on my local network, capable of map and data flow of the connected player on all LAN devices. I have ftp on and implement a file secured with username and password. I tried to connect with the "filter anonymous internet customers' on and outside. I have reset the router 3 - 4 times. Maybe im does not connect make properly. WiFi Smart Displays the FTP server: ftp: / / 172.30.1.19:21. Whenever I try to connect to 172.30.1.19 port 21 in a web browser or ftp program, I get "cannot find server message. I've read through the forums and have not been able to find a solution. Help, please. Thank you.

    So the fix for MY problem was just re-aranging my network would invest and the linksys as being the first unit WAN/LAN on the network of front loading.

  • Can ping cRIO but unable to connect to the MAX

    I have a cRIO 9066 put in place on a local subnet. I think that all the software and drivers are correct. I have deployed my program and it works great except... When I add some optical converters of fibre in the mixture. Here is my system:

    PC--> cable ethernet--> ethernet switch-->--> cRIO ethernet cable * it works fine *.

    PC--> ethernet cable--> converter of fiber--> fiber--> ethernet switch (FPS)-->--> cRIO ethernet cable * unable to connect to MAX *.

    When I connect with ethernet cables all the way through, the ping time is<1ms ttl="" is="" 64.="" when="" i="" add="" the="" fiber="" converter,="" i="" can="" still="" ping="" the="" crio="" but="" ping="" time="" goes="" to="" ~250ms="" and="" ttl="" goes="" to="" 247.="" then="" max="" can't="" connect="" to="" the="" crio.="" is="" my="" connection="" speed="" too="" slow="" for="" max="" or="" the="" crio="" to="">

    My converter fiber and ethernet sfp module switch are all 1000 MB/full duplex. It is run only on a 10 m fiber. I tried several fiber optic cables. I tried the sfp in several locations. My sfp and the switch are both Advantech so I guess that they are compatible with each other. At this point, I plan to buy just a card PCIe fiber for my PC, but I thought I should check first with the experts.

    Thank you

    Hello

    There is a timeout OR max. The default value is 4000 Ms the reason why you are not able to detect the cRIO in NOR-MAX may be because the packages are damaged along the way. If you do not want to check this, you can always monitor the packets with WireShark with two different sets high. In this way, you can see if the packets are defined correctly or not.

    I hope this helps!

  • Unable to connect to the PPPoE server with 2 BEFSR41ver

    I had to get a new AT & T DSL line to a new home with new ID and password. I've never had a problem with the router to the old address and the line DSL.  I've reconfigured the router with a new user name and password for PPPoE I got from AT & T for use with their new motoroal they sent me. The modem gives me the internet when I connect the modem directly to the computer.  When I connect the modem to the WAN port of the router with the computer connected to one of the LAN ports on the router, I get "Unable to connect to PPPoE" when I try to access the internet. When I connect the modem to one of the LAN ports with another port LAN from the router to the computer, I don't have the internet, but this is not recommended for the router cable management. With the modem connected to the WAN router and a power cycle performed port, I still get the same error message. I disabled my firewall and still have the same error message. I don't think I have another firewall to operate.  I never had this problem to my old address and line DSL AT & T with different ID and password and the same router.  Anyone know what is happening?  STEIN

    Your problem is that your "modem" is actually a "modem-router" and it uses the same subnet as the BEFSR41 192.168.1.x.  To resolve this issue, follow these steps:

    All first, reset your BEFSR41 factory default, then set the "local IP address" 192.168.2.1

    To do this, follow these steps:

    To reset your router by default, follow these steps:

    (1) turn off all computers, the router and the modem and disconnect from the wall.
    (2) disconnect all the wires of the router.
    (3) turn on the router and let it start up completely (1-2 minutes).
    (4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
    (5) turn the router.
    (6) connect a computer cable to port 1 of the router (NOT to the internet port).
    (7) turn on the router and let it start up completely (1-2 minutes).
    (8) the power of the computer (if the computer has a wireless card, make sure it's off).
    (9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
    (10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Leave the user name blank and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen).  Then, change the "local IP address" 192.168.2.1, then click the 'Save Settings' button and wait (3 to 60 seconds) of the screen refresh.  You will be probably disconnected from the BEFSR41.  Don't worry about this.  Turn off the BEFSR41 and your computer.

    (11) then, using an ethernet cable, wire the ethernet port of the modem to the Internet port on the BEFSR41.  Turn on your modem and enable good start.  Turn on your BEFSR41 and enable good start.  Turn on your computer.  Test your system, it should work.

    If you can not ' response to... ". "in step 9 above, your router is probably dead.  Report with this info.

    If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. In this case, a report with this problem.

    If you need additional assistance, please state the version of firmware on your router and the results of steps 9 and 10. In addition, if you receive error messages, copy them exactly, and report.

    Please let me know how things turn out for you.

  • Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

    HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

    Have you tried to update the firmware on the DI-514?

    You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
    To give a static IP address to your printer:
    -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
    -Enter the IP address in a browser to reveal the internal settings of the printer.
    -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
    -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
    -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
    -Enter the IP of your router (on the Page of the Network Config) for the gateway.
    -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
    -Click 'apply '.
    Now, stop the router and printer, start the router, wait, and then start printing.

    After that you remove and re - add the printer to your Mac.

    Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

  • Unable to connect to the MKS: address for server esx02.mgmt.domainname.dk host lookup failed: unknown error 11002 (0x2afa)

    I get the following error when I connect to my via Vsphere Vcenter and try to connect to one of my server with the console:

    Unable to connect to the MKS: address for server esx02.mgmt.domainname.dk host lookup failed: unknown error 11002 (0x2afa)

    I'm new to VMware, I can very well do a MSTSC server and work proberly.

    the VMwareTools are out of date, when I log on the server and try to update I get the following message:

    vmware tools error.jpg

    any ideas here?

    I discovered that it is related to DNS

    WSATRY_AGAIN

    11002 (0x2afa)

    It is usually a temporary error during hostname resolution and means that the local server does not valuationauront of response from an authoritative server.

    the issue was that the VMware system was on a different subnet, and the firewall (TMG) blocked. bring the RDP to the Vcenter server and vsphere then open works like a charm

  • A solution to the "unable to connect to the NFS server" that I can't understand

    (This question is related to the interaction between ESXi and FreeNAS and talk a lot here, but the solution was finally on FreeNAS configuration change, so I hope it's ok that I post in this forum.  It relates to the use of FreeNAS of ESXi).

    I have a FreeNAS system set up specifically for the copy of the virtual machines of my ESXi server as a backup mechanism.  I tried to mount a NFS of FreeNAS disk and ran in a (what appears to be, from discussions on the forum, a common place) problem.  ESXi, during an attempt fix the part gave me the "unable to connect to the NFS server" message.  The search in the log files, I could see some more detail, but nothing that pointed to a solution.  I also searched the logs on the FreeNAS system, nothing helps.

    I was using the IP address of the FreeNAS (static address) system instead of the DNS name when you are trying to reach the storage.

    After hours of trying different methods, creation of username on FreeNAS trying up to ESXi, scouring through all the various points of ESXi config, etc. I am getting nowhere.  Then I came across a post somewhere (not here on the forums, but in a blog somewhere) that said add the ESXi server to the hosts on the FreeNAS system file.

    Once we added - bingo-test.  ESXi logged in straight away and I am running.

    Now, I am trying to determine why the addition of ESXi machine to the FreeNAS hosts file would allow ESXi to connect.  Anyone have any ideas?  The IP address of the ESXi system was already in the allowable range set up in the UI on FreeNAS.

    Thanks in advance.

    Mounting NFS export list process requires the resolution of the customer's name. When a customer initiates the request for an NFS share, server checks its list of export for the requested directory and the name of the customer in this access list for this particular action. Now if the server fails to resolve the name of the initiator denies his request for the mounting of this share. In order to overcome this problem, you must have a dns server in the network, or do you have enter you the names and information of IP address to the server hosts file

    Naeem Holy

  • Slow network traffic / expires at ESXi4 host starting from a different subnet, but customers are very well

    I set up a test server ESXi4 and spin various Windows 2003/XP clients and a guest of Vyatta VC5 as my core router.  This has been a strange problem that all traffic to the guests and also are very good, but I can handle only the host with the VI client on the same subnet.  If I can host on a different subnet (even if I leave the cable connected to the same port and vlan), then it becomes unusable.  Many things time out including just trying to download the VI client from the host https page.  Anyone seen this before?

    I have 2 configured vSwitches, one on one vlan isolated to my iSCSI traffic to my storage, and the other as a trunk with the VLAN network management and guest vm on it.  My management network is in the same vlan as one of my comments to VLAN.

    Thanks in advance.

    Yes try to change the e1000 nic,

  • Suddenly 39.0 FF is "unable to connect" to any web page

    I use almost identical installations of 39.0 FF on both computers Windows 7 Pro. On computer 1, for the last two hours, I got "unable to connect" on each URL I tried. It can access things stored locally, such as troubleshooting information. FF on computer 2 is fine, and Chrome and IE work fine on computer 1.

    The problem started watching a movie on Netflix streaming on computer 1. The image suddenly froze and the speakers emitted a wicked repetitive noise - maybe it was 2 seconds of the movie soundtrack play again and again. Commands from the computer totally locked up. I kept only the noise of voltage with power button on the computer. I restarted the computer in safe mode, and then it restarted in normal mode. Now, everything on the computer seems fine - except Firefox.

    I tried to restart FF in safe mode; same problem in the corresponding mode. I saved copies of information for troubleshooting in safe and regular mode, and a copy of the submitted crash reports also list. I'll share these if you tell me how. (Can't do it with the button "Share data", of course, because I can't go to this form to ask a question on computer 1 - I am posting this to computer 2)

    The only thing I have not tried is "Refresh Firefox". I'd really rather not do that, because it will scan all my modules and customizations.

    Would appreciate any help you can offer.

    Start the computer in Mode safe mode with network support Windows (on the startup screen, press F8) as a test.

    ....
    You can check problems caused by malware.

    Make a check of malware with several malware scanning of programs on the Windows computer.
    Please scan with all programs, because each program detects a different malicious program.
    All of these programs have free versions.

    Make sure that you update each program to get the latest version of their databases before scanning.

    Alternatively, you can write a check for an infection rootkit TDSSKiller.

    See also:

Maybe you are looking for

  • Yet WT8 - WiFi signal reception problem

    HelloI hope someone could help me! I bought a Tablet still 8 a few weeks ago and just after the first start, I found a problem in the reception of the wireless signal. When she acquires the signal, there's always between 1 or 2 marks in the indicatio

  • Drivers not installed with the upgrade to Win 8i.1

    I have improved my Elitebook 8560 to 8.1 Windows Device Manager shows no driver for "Base system device" and two unknown devices described as ACPI\HPQ0004\3 & E89B380 & 0 and USB\VID_138A & PID_003C\0020DEC80B8A Whay drivers do I need, where? Thank y

  • HP 6830:6830 scanning

    I created my printer 6830 with assistance from Support.  Now, I try to scan a document and send it in the glass.  The screen shows this analysis was good and full email.  I added myself to the recipients.  I have not received the email.  Any suggesti

  • Photo multi mess - how can you get rid of duplicate images?

    How to get rid of duplicated images, I have 3000 photos more than half are the DUP dup, the DUP help!

  • my HP Officejet Pro 8600 printer will not feed

    All the lights are out on my printer. I tried to unplug, plug is fine, reconnected. Nothing happens. Is there a switch on / off or reset? I've only had this printer for a few months...