Unable to connect to targets PXI - 8196 RT in MAX

I'm trying to set up the initial connection to my goal of RT (it is a model used, configured by an engineer OR running LabVIEW RT front arrived at our laboratory), but did not have much success.  I have connected the target RT, a PXI-8196, directly on my Windows computer using an Ethernet cable and manually set an IP address for this connection in Windows Network & Sharing Center.  When I try to connect to the target of RT in NOR-MAX, I do the following:--> create a new--> remote device (not on the local subnet) enter the IP address I specified manually.  When I type "Finish", however, I get the following error message: "failed to initialize the remote connection or targets.

I have disabled the Windows Firewall on the Ethernet port and also downloaded and re-installed PXI Platform Services.  Is there a step I'm missing, or anyone any suggestions of what else to try?

I use NI MAX version 5.6, Windows 8 running on the host computer and the on-board computer is a PXI-8196.  Thanks in advance!

I just went through this with another PXI controller.  Absolutely, you don't want the PXI to reach a binding address local 169.254.x.x, because this will allow you to force MAX to connect.

Start by setting is using your PXI controller upwards with a monitor, so you can see what is happening, and that it address and a keyboard, if you need to enter the BIOS of the controller.

On your PC, connect an Ethernet cable from the NETWORK adapter that you use for communication PXI for PXI.

Assuming that your PXI has a 169.254.x.x address, configure your NETWORK card to also have a similar (but different) address, by using a subnet mask of 255.255.0.0 (so the 169,254 pieces must match, but the other two numbers is not guaranteed).

Now open MAX.  Click on remote systems.  I guess you don't show anything there, and the right pane is empty.  In the right pane, click on «Create a new...» "and select"remote device (not on the local subnet).  Yes, it is on the local subnet, but never mind.  When it prompts you for the IP, put the IP address that the PXI monitor shows like PXI IP.  He must find the controller almost instantly.

What I'd do next is to configure the IP address that you want to use.  In my case, I use addresses from 10.0.x.x for both my network cards that "speaks" my PXI and PXI.  While MAX talk to your PXI, you can set the IP address, and then restart the PXI - you should see it happen to the new IP address you specified.  Of course, if you change its IP address to a 10.0.x.x address, you will need to change your NETWORK card to also use an address in this range.  Once both have been reset, MAX should be able to find the PXI under remote systems.

Now, all you have to do is add/remove software and you should be good-to-go.

Bob Schor

Tags: NI Software

Similar Questions

  • Unable to connect to target iSCSI for ESX 3.5

    Hi all

    I have an esx 3.5 build 82663 (update 1). We took over this company, so we are migrating this data center. I understand tha patch isn't 5 update but it wasn't our environment and we try to turn it on.

    We have three esx servers

    (1) console production svc - 192.168.7.x

    (2) storage network - 192.168.9.x

    EqualLogic 3)-192.168.9.x

    (4) storage Switch - CISCO 3750 Switch

    (5) frames enabled on vswitch, vmknic, physical, switch, network interface cards, table vlan and storage.

    (6) software iscsi client allowed an outgoing connection through 3260 (tcp)

    Performed troubleshooting

    esxcfg-vmknic - l - seems ok and with activated jumbo frames

    esxcfg-NICS - l - looks ok with activated jumbo frames

    esxcfg-vswitch - l - looks ok with activated jumbo frames

    esxcfg-road - l - (looks good)

    192.168.7.0 255.255.255.0 local subnet

    192.168.9.0 255.255.255.0 local subnet

    by default 0.0.0.0 192.168.7.1

    Works of vmkping between the storage network interfaces (192.168.7.x) i.e. physical switch, equallogic, and other interfaces for esx storage network.

    vmkping s 9000 192.168.9.11 (equallogic san) works without packet loss.

    Ping does not work between interfaces.

    Ping of physical switch to the san and esx equallogic storage network interfaces work

    Access to LUNS equallogic shared among interfaces are restrticted by the ip address of storage network (192.168.9.x). The LUNS they check marks against them to have several initiators communicate with them.

    No enabled chap authentication anywhere.

    I had another server with the same configuration connection to it without problems to the only difference is esxi can be accessed and the esx servers cannot access.

    Our environment has been only esxi. This is the first time I use esx and a system of update 1 for iSCSI.

    I'm on the critical path to complete the project.

    It would be useful that I can get all the help you can.

    See you soon,.

    Knockaert

    If I'm not mistaken in your service console needed to have access to the storage network 3.5 too.  Try to configure a second service on the storage network console and see if you can view the LUNS.   Can also be useful to filter through the vmkernel logs and see if you notice any errors.

    If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

  • OR PXI-8196 target using a USB stick formatting

    Hello everyone,

    I use a PXI chassis with controller PXI-8196 and multiple PXI DAQmx cards. I need to format the hard drive on the target of PXI and reinstall the RT operating system as well as all other software. I am trying to restart the PXI with a USB bootable, but it gives me the option to format the hard drive.

    Here are the steps I followed.

    1. I created the disk bootable with MAX using the RT disc utilities > create Desktop PC USB Drive Utility (PXI-8196 does not have a floppy drive so I have to use a USB key)

    2. I have connected a keyboard and screen to target to see it start.

    3. I've also adjusted the sequence of boot as the boot option "USB HDD: LEXAR JUMPDRIVE SPORT" among those available in the boot sequence has the highest priority. (My USB is a USB of LEXUS so I'm sure that this particular option must be the first in the sequence).

    4 but once I start my system. It does not give me the option to format (according to MAX documentation should give me an option to "format hard drive"). Here's what I see on the screen connected to the target

    = = The output to the screen is bounded by these two rails =.

    Boot mode safe of Romans...

    Enter safe mode.

    The IP address is: 10.10.10.2

    _

    ===========================================================================

    At the end of the last cursor keeps blinking and nothing happens

    5. the 10.10.10.2 IP address is the address in the configuration I want to format and reinstall. So I don't know if he meant to keep automatically previous IP address.

    6. to avoid the fact that there may be something wrong with the USB, I repeated the procedure as a whole with another USB drive. But exactly the same thing happens again.

    Please help me it reboot with a USB port and format the hard drive and reinstall all software.

    Thanking in anticipation.

    Vivek.

    Hello

    Try this, go into the BIOS of the PXI, under LabVIEW RT to the startup configuration, change the Windows option / other OS. Then try what you are doing.

    Let me know if it works for you

  • PXI-8196 connection problem: plugin not installed

    Hello OR:

    The PC in interaction with our NI PXI-8196 (1052 chassis) has recently had a hard drive failure, and I had to reinstall all our LabVIEW software and live custom on a new host. The software is running, but I have problems with connectivity to PXI. PXI is recognized to the MAX, and everything is accessible (ladders for our load cells, etc.). But when I open my project to a labview VI, I can not connect for PXI. It has a yellow triangle with an exclamation mark next to it, and when I right click, the error message indicates that the plug-in is not installed. I have a CD that seems to have the PXI drivers on it, but after the installation, I got the same problem.

    I wasn't the one who originally this system connected to the network, and I cannot find documentation to get back up and running. Any help would be greatly appreciated!

    Eric

    So I solved my problem with the help of my local applications engineer. He pointed to me and made sure that the software on the PXI system synchronized with the host computer via the MAX add/remove software menu. I noticed that the version of the RT software on my host was older than the version on the PXI system. Not sure why this happened, as I had already installed the most updated version. Maybe he got more written in my flurry of facilities. So I reinstalled the RT 8.2 module on the host, and now everything works. Thanks for your time, Robert.

  • Unable to connect to a real-time target... ugh I give up!

    This one is really frustrating... I did a lot with Labwindows for a long time, so get in... I just installed LW/CVI 2013 on a new machine in my lab.  hooked to a new PXI chassis, formatted a new disk in and installed all the drivers.  When you try to connect to the target environment labwindows I get the popup in the screenshot.  As you can see, the chassis is on the network, to the good ip, and the drivers are installed on the target... What is the problem!  Thank you.

    Hello

    This is the acutally NOR Configuration system that comes with MAX and interferes during the installation of the CVI real-time on the target.

    Decommissioning of MAX should solve the problem.

    If you don't want to upgrade to CVI real-time Module to 2013 SP1 there is also a work around:

    Edit C:\Program NIUninstaller Instruments\RT Images\CVI\version\cvilvrt.cdf and do one of the following:
    Remove the entry from CVIRealTimePeer.
    Specify the IP address or desired host name.
    Reinstall the LabWindows/CVI runtime for RT component to the target via NI MAX.

    Good day

    Constantin

  • Unable to connect target database using dbclient

    Hi all

    I installed database 11.2.0.2 successfully on linux machine.other machine is windows machine, I installed in CUSTOMER DB 11.2.0.2 by using db client unable to connect target database.


    Database version: 11.2.0.2(64 bit)

    Windows database: 11.2.0.2(32bit)


    Thank you
    GS

    I installed database 11.2.0.2 successfully on linux machine.other machine is windows machine, I installed in CUSTOMER DB 11.2.0.2 by using db client unable to connect target database.

    Set up Listener on the server?

    Can you tnsping from windows to linux machine?

  • Unable to connect to my target database

    I am trying to create a clone of my database named proddb using my backup RMNA production,
    so, when I export ORACLE_SID = proddb
    and then try to connect to my use of rman
    RMAN target /.

    its projection connected to database clonedb target

    I checked the servicxes and there is no service not named clonedb and there is no entry in my tnsnames or listner file like clonedb...

    user9038728 wrote:
    [Oracle@localhost ~] $ export ORACLE_SID = proddb
    [oracle@localhost ~] $ export ORACLE_HOME=/home/oracle/app/oracle/product/11.2.0/dbhome_1/

    [oracle@localhost ~] $ rman target sys/password

    Recovery Manager: release 11.2.0.1.0 - Production on Fri Jan 6 11:27:13 2012

    Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.

    connected to target database: CLONEDB (unassembled)

    RMAN >

    This is the output that I am getting...

    Your Production/source/target database must be in an OPEN state & your new/clone/auxiliary instance must be started/no mounted State.

    You need to connect you as below

    $rman auxiliary sys/***@prod target.

    Then the target will be production, you must export the auxiliaries SIDS and test connectivity TNS at the elementary level.

  • Unable to connect to starter kit 2.0 Robotics

    Hi all

    I know this question has been askedmultiple times, and I read trough forum messages, but cannot find a solution.

    When I try to run a robotics project on DaNI, 2.0 Starter kit, I get a message of conflict resolution, saying "unable to connect to the target. --> See image rasthaus

    I installed the latest version of labview, robotics, FPGA modules and in real time as well as pilots of RIO.

    Once I disabled my firewall, I was able to detect the robot with MAX, but I was not even able to connect using labview.

    Thanks for any help,

    MortZxD

    Hello

    I had the same IP address as illustrated by MAX in my library of projects, but I could not always connect.

    I reset the IP address of the robot to start in safe mode and changing an address IP static, dynamic and who did the tour!

    Thnks

  • Unable to connect IDE device after upgrade to 10.3.1

    Hi all

    I had updated the BlackBerry smartphone to 10.3.1, and after the upgrade, I am unable to connect my machine to Momentics IDE or deploy an application on the device of comand prompt.

    When I try to deploy from the command prompt, I get the following error.

    Error: Cannot connect: Connect to /169.254.0.1:443 timed out. Please check IP address settings for the target. You may have to reboot the target.

    Development on my device is set on IT.

    Concerning

    I had mode developer cross checked several times, but without success.

    Problem is solved.

    I deleted the data unit and then installed the upgrade pushed by Blackberry. Magic happened and it started working.

  • Unable to connect to the VMware web service: invalid key file

    Hello

    We have a CPO 2.3.1 who refuses to connect to vCenter (see newspaper excerpt at the end of the post).

    Recently, we changed our server vCenter (part of a 5.1 update).

    We tried the following workarounds:

    • Remove and add all the elements of the platform from the portal using services SE
    • Re import automation packs (4 of the Starter Edition v2.3.1.38)
    • Re on the keystore password

    No change at all...

    Do you have an idea on how to fix this?

    Thank you.

    Kind regards

    Stone

    || 235. 02/10/2012 15:46:21.667 | 6072. WCF: http://schemas.microsoft.com/2004/10/E2ETraceEvent/TraceRecord ' gravity 'Error' = >http://msdn.microsoft.com/en-US/library/System.ServiceModel.Diagnostics.TraceHandledException.aspxhandling of an exception. . Tidal.Automation.Server.exe Tidal.Scheduler.Common.Communications.CommunicationException, Tidal.Scheduler.Common, Version = 2.3.0.0, Culture = neutral, PublicKeyToken = fba593b23cf207cdthe connection attempt (VMware vCenter Server (603) @VMware vCenter Server (603)) failed due to the following error: unable to connect to the VMware web service: Invalid keystore. to Tidal.Automation.Server.JavaAdapterBase.PerformServerAssistedOperation (ServerAssistedOperation operation, target TargetConfiguration, RuntimeUserConfiguration runtimeUser)

    to Tidal.Automation.Server.JavaAdapterBase.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Engine.Core.Adapter.SuspendableAdapter. & lt; & gt; c__DisplayClass1c. & lt; PerformServerAssistedOperation & gt; b__1b(IAdapter adapter)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction, haltingAction Boolean, Int32 remainingRetries)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction, Boolean haltingAction)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction)

    to Tidal.Automation.Engine.Core.Adapter.SuspendableAdapter.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Engine.Core.AdapterSystem.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Server.WebService.AdapterService.PerformServerAssistedOperation (operation ServerAssistedOperation)

    at SyncInvokePerformServerAssistedOperation (Object, Object [], Object [])

    at System.ServiceModel.Dispatcher.SyncMethodInvoker.Invoke (object instance, entered to Object [], Object [] & amp; outputs)

    at System.ServiceModel.Dispatcher.DispatchOperationRuntime.InvokeBegin (MessageRpc & amp; CPP)

    at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage5 (MessageRpc & amp; CPP)

    at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage31 (MessageRpc & amp; CPP)

    at System.ServiceModel.Dispatcher.MessageRpc.Process (Boolean isOperationContextSet)Tidal.Scheduler.Common.Communications.CommunicationException: the connection attempt (VMware vCenter Server (603) @VMware vCenter Server (603)) failed due to the following error: unable to connect to the VMware web service: invalid key file.

    at Tidal.Automation.Server.JavaAdapterBase.PerformServerAssistedOperation (ServerAssistedOperation operation, target TargetConfiguration, RuntimeUserConfiguration runtimeUser)

    to Tidal.Automation.Server.JavaAdapterBase.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Engine.Core.Adapter.SuspendableAdapter. & lt; & gt; c__DisplayClass1c. & lt; PerformServerAssistedOperation & gt; b__1b(IAdapter adapter)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction, haltingAction Boolean, Int32 remainingRetries)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction, Boolean haltingAction)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction)

    to Tidal.Automation.Engine.Core.Adapter.SuspendableAdapter.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Engine.Core.AdapterSystem.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Server.WebService.AdapterService.PerformServerAssistedOperation (operation ServerAssistedOperation)

    at SyncInvokePerformServerAssistedOperation (Object, Object [], Object [])

    at System.ServiceModel.Dispatcher.SyncMethodInvoker.Invoke (object instance, entered to Object [], Object [] & amp; outputs)

    at System.ServiceModel.Dispatcher.DispatchOperationRuntime.InvokeBegin (MessageRpc & amp; CPP)

    at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage5 (MessageRpc & amp; CPP)

    at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage31 (MessageRpc & amp; CPP)

    at System.ServiceModel.Dispatcher.MessageRpc.Process (Boolean isOperationContextSet)

    || 236. 02/10/2012 15:46:21.667 | 6072. An exception that is not of type rhapsodyexception has been captured while a webmethod call was made.  This exception has been intercepted and generic.

    || 231: 02/10/2012 15:46:21.667 | 6072. EXCEPTION (Tidal.Scheduler.Common.Communications.CommunicationException): The connection attempt (VMware vCenter Server (603) @VMware vCenter Server (603)) failed due to the following error: unable to connect to the VMware web service: invalid key file.

    Stack trace: at Tidal.Automation.Server.JavaAdapterBase.PerformServerAssistedOperation (ServerAssistedOperation operation, target TargetConfiguration, RuntimeUserConfiguration runtimeUser)

    to Tidal.Automation.Server.JavaAdapterBase.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Engine.Core.Adapter.SuspendableAdapter. <> c__DisplayClass1c. b__1b(IAdapter adapter)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction, haltingAction Boolean, Int32 remainingRetries)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction, Boolean haltingAction)

    at Tidal.Automation.Engine.Core.AdapterLifecycleManager.PerformAdapterAction (Guid IDCarte, action AdapterAction)

    to Tidal.Automation.Engine.Core.Adapter.SuspendableAdapter.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Engine.Core.AdapterSystem.PerformServerAssistedOperation (operation ServerAssistedOperation)

    to Tidal.Automation.Server.WebService.AdapterService.PerformServerAssistedOperation (operation ServerAssistedOperation)

    at SyncInvokePerformServerAssistedOperation (Object, Object [], Object [])

    at System.ServiceModel.Dispatcher.SyncMethodInvoker.Invoke (object, Object [], Object [] entries & exits instance)

    at System.ServiceModel.Dispatcher.DispatchOperationRuntime.InvokeBegin (MessageRpc & CPP)

    at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage5 (MessageRpc & CPP)

    at System.ServiceModel.Dispatcher.ImmutableDispatchRuntime.ProcessMessage31 (MessageRpc & CPP)

    at System.ServiceModel.Dispatcher.MessageRpc.Process (Boolean isOperationContextSet)

    You have an invalid key file because the HTTPS certification has changed. You must remove the old keystore file and restart the OPC Server and then reconnect / run something against vCenter.

    It is also possible to host Adatper framework/java problems I've seen often.

    If you need more information, you will need to prosecute TAC with your service contract please. Normally, we try to solve no newspapers on the forums.

    -Shaun Roberts

    CIAC/CPO support team leader

    [email protected] / * /.

  • Unable to connect to the network "\\localmachine\sharedname" share

    I use VMware vCenter Converter Standalone client, v5.0.0 build-470252, running on a 64-bit Windows 7 computer, try to import a Windows 2008 computer virtual (hosted by VMWare infrastructure) on my local machine.

    At the start of the converter, I have "connecting to a local server.

    Specification of the source system is OK, even if I don't know the certificate error.  The conversion wizard installs his agent and it connects OK.

    To the Destination System, I said:


    Type of destination: VMware Workstation or other virtual machines to VMware
    Product VMware: VMware Workstation 8.0.x
    Information on the virtual machine:
    Name: same as the source system, such as detected by the converter
    Location for the virtual machine: \\localmachine\sharedfoldername
    Username and password: my Windows 7 credentials, with full control over \\localmachine\sharedfoldername, the action and the underlying folder.

    "When the converter checks the destination settings, it is reported: unable to connect to the network"\\localmachine\sharedfoldername"share

    So far the measures of investigation:
    -Connection to the share through Windows Explorer works fine; It is possible to write to the share

    -J' tried specifying the share as '\\localhost\sharedfoldername', but get "the share specified network 'localhost\sharedfoldername' does not exist."  It was a bit of a long shot, I guess, but the form does not work in Windows Explorer.

    -Have you tried with the file and print sharing both power - on and off seemed worth a try after looking at other posts on this forum

    The help says 'If you are connected to a local Converter Standalone Server, providing a network path or a local path to the destination directory'.  I tried the local path "C:\Virtual Machines\sharedfoldername", but got the message "error: specified as a (local) drive Destination.»  "Please specify a UNC path such as: \\machine\sharename.

    Aid also States "You have not to provide user credentials if the location is on the local storage of the machine where Converter Standalone server running."  However, the next button is always disabled until credentials are provided.

    Can anyone help please?

    You must be able to access the \\localmachine\sharedname of the * SOURCE * machine. The job of conversions P2V of Windows is to install an agent on the source, then the agent connects to the target (this is why it must be on a network share) and transfers the data. You can browse \\localmachine\sharedname of the source (but not where the converter is installed)?

  • Cloud new control panel - unable to connect to the agent

    I'm done just to install the last control of cloud 12.1.0.3 by following oracle document e22624.

    Everything installed fine and I am able to connect to the cloud control. I manually added a target (our test server). The installation was successful without error.

    However the cloud control shows: error of assessment metrics start - unable to connect to the agent to https://server:3872/emd/main / [Connection timed out: connect]


    I ran the following on the test server to make sure that the management agent runs:

    /opt/app/oracle/product/12.1.0/agent/core/emctl status agent

    and I see this:

    Oracle Enterprise Manager 11g Database Control Release 11.2.0.3.0

    Copyright (c) 1996, 2011 Oracle Corporation.  All rights reserved.

    ---------------------------------------------------------------

    Agent version: 10.2.0.4.4

    Version of the WHO: 10.2.0.4.4

    Protocol version: 10.2.0.4.4

    Agent home: /opt/app/oracle/product/11.2.0/dbhome_1/server_test

    File binary agent: /opt/app/oracle/product/11.2.0/dbhome_1

    Agent process ID: 24514

    Parent process ID: 23632

    Agent URL: https://server:3938/emd/main

    Repository URL: https://server:1158/em/upload /

    Starts at: 2013-11-15 13:16:53

    Started by user: oracle

    Last reload: 2013-11-15 13:16:53

    Last download successful: 2013-11-15 14:34:02

    Total megabytes of XML files uploaded so far: 2.68

    Number of XML, waiting for loading files: 0

    Size of the XML files in the upload wait (MB): 0.00

    Available disk space on the file upload system: 81.34%

    Directory to upload Data channel: /opt/app/oracle/product/11.2.0/dbhome_1/server_test/sysman/recv

    Last pulse in SGD: 2013-11-15 14:36

    ---------------------------------------------------------------

    Agent is running and ready

    According to state that something is wrong. The test server is currently installed OEM Database Control. The directions said nothing about not being able to install Cloud control and have control OEM database.


    My question is this: can I have the OEM Database Control and control of Cloud? If this is not the case, what should I do to get the Cloud control to work?


    Thank you

    I opened a support ticket with Oracle. It was that the firewall is blocking communication from the SGD server to the agent. Everything works now as expected.

  • BCC error: unable to connect to the server FlexUI/messagebroker/amf

    Hi all

    When I try to access various parts of the ICC as a "Commercial goods" or "targeting and Segmentation-> Merchandising" I get an alert with the following error:

    Unable to connect to the server http://ATG.local:8180 / FlexUI/messagebroker/amf

    I see two exceptions in server.log:

    2013-10-02 16:29:02, ERROR [STDERR] (main) 113 * MessageBrokerServlet failed to initialize due to runtime exception: Exception: java.lang.NullPointerException

    ..

    2013-10-02 16:29:02, INFO 117 [org.apache.catalina.core.ContainerBase. [JBoss.Web]. [localhost]. [/FlexUI]] (main) Marking of servlet MessageBrokerServlet as unavailable

    2013-10-02 16:29:02, ERROR 117 [org.apache.catalina.core.ContainerBase. [JBoss.Web]. [localhost]. [/FlexUI]] (main) Servlet /FlexUI threw the exception in load()

    javax.servlet.UnavailableException

    Full stack trace: http://pastebin.com/raw.php?i=UGbgbrUn

    I don't see anything in the documentation on the configuration of Flex or in the forum about this error.

    Any idea?

    Thanks a lot for your help, once again!

    Concerning

    Mention your ATG/App Server/JDK versions.

  • RC-40201: unable to connect to the TEST database running adcfgclone.pl appsTier

    Hi Experts,

    While performing a cloning my instance of R12, I got RC-40201 error when I ran "adcfgclone.pl appsTier.

    [appltst@oracleupk bin] $ perl adcfgclone.pl appsTier

    Copyright (c) 2002 Oracle Corporation

    Redwood Shores, California, USA

    Applications Oracle rapid Clone

    Version 12.0.0

    adcfgclone Version 120.31.12010000.1

    Enter the password for APPS:

    Running:

    / data/appl_top/apps/apps_st/comn/clone/bin /... / JRE/bin/Java-Xmx600M - cp /data/appl_top/apps/apps_st/comn/clone/jlib/java:/data/appl_top/apps/apps_st/comn/clone/jlib/xmlparserv2.jar:/data/appl_top/apps/apps_st/comn/clone/jlib/ojdbc14.jar oracle.apps.ad.context.CloneContext EI/data/appl_top/apps/apps_st/comn/clone/bin /... /Context/Apps/CTXORIG.xml-valider - pairsfile /tmp/adpairsfile_24425.lst-stade/data/appl_top/apps/apps_st/comn/clone 2 > /tmp/adcfgclone_24425.err; ECHO $? > /tmp/adcfgclone_24425.res

    Logfile located at /data/appl_top/apps/apps_st/comn/clone/bin/CloneContext_0912145803.log

    Provide the values required for the creation of the new file APPL_TOP context.

    Target System Hostname (virtual or normal) [oracleupk]:

    SID data system target: TEST

    Target database system [oracleupk] server node:

    Target system Base Directory: / data / appl_top

    Target system tools ORACLE_HOME directory [/ data/appl_top/apps/tech_st/10.1.2]:

    Target Web ORACLE_HOME directory system [/ data/appl_top/apps/tech_st/10.1.3]:

    Target system APPL_TOP directory [/ data/appl_top/apps/apps_st/appl]:

    Target system COMMON_TOP directory [/ data/appl_top/apps/apps_st/comn]:

    Target system Instance home directory [/ data/appl_top/inst]:

    Target system service root [activated]:

    Target Web Entry Point [active] System Services:

    Target [active] System Web Application Services:

    Target [active] Batch Processing Services system:

    Other Services target system [off]:

    You want to preserve the display [oracleupk:0.0] (y/n)? : n

    Target display system [oracleupk:0.0]: oracleupk:1.0

    System Target Pool [0-99] port: 80

    Audit of the pool of port 80

    fact: Port 80 pool is free

    Report file is located at /data/appl_top/inst/apps/TEST_oracleupk/admin/out/portpool.lst

    Information available at /data/appl_top/inst/apps/TEST_oracleupk/admin/out/portpool.lst complete port

    RC-40201: unable to connect to the TEST database.

    Create the new file APPL_TOP context of:

    /Data/APPL_TOP/apps/apps_st/appl/ad/12.0.0/admin/template/adxmlctx.tmp

    The new context APPL_TOP file was created:

    / Data/APPL_TOP/inst/Apps/TEST_oracleupk/Appl/admin/TEST_oracleupk. XML

    Logfile located at /data/appl_top/apps/apps_st/comn/clone/bin/CloneContext_0912145803.log

    Check the context Clone logfile /data/appl_top/apps/apps_st/comn/clone/bin/CloneContext_0912145803.log for more details.

    Clone of fast running with the command:

    Perl java /data/appl_top/apps/apps_st/comn/clone/bin/adclone.pl = / data/appl_top/apps/apps_st/comn/clone/bin /... /JRE mode = apply dialing = / data/appl_top/apps/apps_st/comn/clone point = appsTier = CUSTOM appctxtg=/data/appl_top/inst/apps/TEST_oracleupk/appl/admin/TEST_oracleupk.xml contextValidated = true showProgress method

    Running:

    Perl java /data/appl_top/apps/apps_st/comn/clone/bin/adclone.pl = / data/appl_top/apps/apps_st/comn/clone/bin /... /JRE mode = apply dialing = / data/appl_top/apps/apps_st/comn/clone point = appsTier = CUSTOM appctxtg=/data/appl_top/inst/apps/TEST_oracleupk/appl/admin/TEST_oracleupk.xml contextValidated = true showProgress method

    Apps for password:

    Start application layer apply - Fri Oct 12 15:01:20 2013

    / données/appl_top/apps/apps_st/comn/clone/bin /... /jre/bin/java -Xmx600M -DCONTEXT_VALIDATED=true -Doracle.installer.oui_loc=/oui -classpath /data/appl_top/apps/apps_st/comn/clone/jlib/xmlparserv2.jar:/data/appl_top/apps/apps_st/comn/clone/jlib/ojdbc14.jar:/data/appl_top/apps/apps_st/comn/clone/jlib/java:/data/appl_top/apps/apps_st/comn/clone/jlib/oui/OraInstaller.jar:/data/appl_top/apps/apps_st/comn/clone/jlib/oui/ewt3.jar:/data/appl_top/apps/apps_st/comn/clone/ jlib/Oui/share.jar:/data/appl_top/apps/apps_st/ Comn/clone/jlib/Oui/srvm.jar:/Data/APPL_TOP/Apps/apps_st/COMN/clone/jlib/ojmisc.jar oracle.apps.ad.clone.ApplyAppsTier EI /data/appl_top/inst/apps/TEST_oracleupk/appl/admin/TEST_oracleupk.xml-/data/appl_top/apps/apps_st/comn/clone - scene showProgress

    Password APPS: log file located at /data/appl_top/inst/apps/TEST_oracleupk/admin/log/ApplyAppsTier_09121501.log

    -79% completed

    ERROR when executing apply...

    Fri Oct 12 15:07:47 2013

    ERROR: Cannot run /data/appl_top/apps/apps_st/comn/clone/bin/adclone.pl

    Contents of the log file: -.

    [AutoConfig error report]

    The following report lists the errors autoconfig met in each

    execution phase.  Errors are grouped by directory and by phase.

    The format of the report is:

    < file name > < phase > < eventually return code >

    [INSTALLATION STAGE]

    AutoConfig could not successfully run the following scripts:

    Directory: / data/appl_top/inst/apps/TEST_oracleupk/admin/install

    adgendbc.sh INSTE8_SETUP 1

    afcpnode.sh INSTE8_SETUP 1

    afgcsreg.sh INSTE8_SETUP 1

    txkWfClone.sh INSTALL_SETUP 1

    [PROFILE PHASE]

    AutoConfig could not successfully run the following scripts:

    Directory: /data/appl_top/apps/tech_st/10.1.3/perl/bin/perl-je /data/appl_top/apps/tech_st/10.1.3/perl/lib/5.8.3-je /data/appl_top/apps/tech_st/10.1.3/perl/lib/site_perl/5.8.3-je /data/appl_top/apps/apps_st/appl/au/12.0.0/perl-je /data/appl_top/apps/tech_st/10.1.3/Apache/Apache/mod_perl/lib/site_perl/5.8.3/i686-linux-thread-multi /data/appl_top/inst/apps/TEST_oracleupk/admin/scripts/adexecsql.pl sqlfile = / data/appl_top/inst/apps/TEST_ oracleupk/admin /. install

    afwebprf. SQL INSTE8_PRF 1

    amscmprf. SQL INSTE8_PRF 1

    amswebprf. SQL INSTE8_PRF 1

    bisadmprf. SQL INSTE8_PRF 1

    bisdblrp. SQL INSTE8_PRF 1

    clnadmprf. SQL INSTE8_PRF 1

    cncmprf. SQL INSTE8_PRF 1

    cseadmprf. SQL INSTE8_PRF 1

    csfadmprf. SQL INSTE8_PRF 1

    csiadmprf. SQL INSTE8_PRF 1

    eamadmprf. SQL INSTE8_PRF 1

    fteadmprf. SQL INSTE8_PRF 1

    ibywebprf. SQL INSTE8_PRF 1

    icxwebprf. SQL INSTE8_PRF 1

    oksfrmprf. SQL INSTE8_PRF 1

    wshadmprf. SQL INSTE8_PRF 1

    Directory: / data/appl_top/inst/apps/TEST_oracleupk/admin/install

    adadmprf.sh INSTE8_PRF 1

    admk80ln.sh INSTALL_PRF 1

    afadmprf.sh INSTE8_PRF 1

    afcpctx.sh INSTE8_PRF 1

    afcpgsm.shINSTE8_PRF1
    igccmprf.shINSTE8_PRF1
    jtfictx.shINSTE8_PRF1
    okladmprf.shINSTE8_PRF1
    txkJavaMailerCfg.shINSTE8_PRF1
    txkWebServicescfg.shINSTE8_PRF1

    [APPLY PHASE]

    AutoConfig could not successfully run the following scripts:

    Directory: /data/appl_top/apps/tech_st/10.1.3/perl/bin/perl-je /data/appl_top/apps/tech_st/10.1.3/perl/lib/5.8.3-je /data/appl_top/apps/tech_st/10.1.3/perl/lib/site_perl/5.8.3-je /data/appl_top/apps/apps_st/appl/au/12.0.0/perl-je /data/appl_top/apps/tech_st/10.1.3/Apache/Apache/mod_perl/lib/site_perl/5.8.3/i686-linux-thread-multi/data/appl_top/inst/apps/TEST_oracleupk/admin/install
    adadmat.plINSTE8_APPLY1

    Fate of 31 stateful auto-configuration

    RC-50014: Fatal: failed to run the auto configuration service

    Asked by oracle.apps.ad.clone.ApplyApplTop

    ERROR: AutoConfig completed with errors. Check the logfile at /data/appl_top/inst/apps/TEST_oracleupk/admin/log/ApplyAppsTier_09121501.log for more details.

    ApplyApplTop completed successfully.

    # Check the race situation AutoConfig of ApplyApplTop

    WARNING: The autoconfiguration service has completed with errors.

    Please help me solve this problem, your prompt response will be highly appreciated.

    -Thank you

    Ankur

    Audit of the pool of port 70

    fact: Port pool 70 is free

    You used port 70 for the node of the database layer, so you will need to use the same port pool (70 instead of 80) when running "perl adcfgclone.pl appsTier.

    Thank you

    Hussein

  • DOUBLE DB: ORA-17629: unable to connect to the remote database server

    [oracle@ora11g1 ~] $ export ORACLE_SID = sales
    [oracle@ora11g1 ~] $ rman target sys/sales@sales

    Recovery Manager: release 11.2.0.1.0 - Production Wed Jun 5 13:00:15 2013

    Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.

    connected to target database: SALES (DBID = 690066655)

    RMAN > Connect auxiliary sys/salestby2@salestby2

    connected to the auxiliary database: SALES (not mounted)

    RMAN > CURRENT SPFILE DATABASE of TARGET duplicate FOR THE EVE OF the DATABASE
    2 > DB_NAME SET = 'sales '.
    3 > SET DB_UNIQUE_NAME = "salestby2".
    4 > control_files='/u02/oradata/salestby2/control01.ctl','/u02/oradata/salestby2/control02.ctl SET'
    5 > SET DB_FILE_NAME_CONVERT = "/ u02/oradata/sales /", "/ u02/oradata/salestby2 / '.
    6 > SET LOG_FILE_NAME_CONVERT = "/ u02/oradata/sales /", "/ u02/oradata/salestby2 / ';

    From duplicate Db 5 June 13
    using the control file of the target instead of recovery catalog database
    allocated channel: ORA_AUX_DISK_1
    channel ORA_AUX_DISK_1: SID = 20 type of device = DISK

    content of Script memory:
    {
    backup that copy reuse
    TargetFile ' / auxiliary format of the u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwsales
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwsalestby2' targetfile
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesales.ora' auxiliary format
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesalestby2.ora';
    clone of SQL 'alter system set spfile = "/u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesalestby2.ora";
    }
    execution of Script memory

    From backup 5 June 13
    allocated channel: ORA_DISK_1
    channel ORA_DISK_1: SID = 58 type of device = DISK
    RMAN-03009: failure of the backup command on the channel ORA_DISK_1 at 05/06/2013 13:05:26
    ORA-17629: unable to connect to the remote database server
    ORA-17627: ORA-01017: name of user and password invalid. connection refused
    ORA-17629: unable to connect to the remote database server
    continue other job steps, not a not working will not re-run
    RMAN-00571: ===========================================================
    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
    RMAN-00571: ===========================================================
    RMAN-03002: failure of Db in dual at 05/06/2013 13:05:27
    RMAN-03015: an error has occurred in the script stored memory Script
    RMAN-03009: failure of the backup command on the channel ORA_DISK_1 at 05/06/2013 13:05:27
    ORA-17629: unable to connect to the remote database server
    ORA-17627: ORA-01017: name of user and password invalid. connection refused
    ORA-17629: unable to connect to the remote database server

    Welcome to the oracle forums!

    Please take the time to go through [url https://forums.oracle.com/forums/ann.jspa?annID=1535] FAQ PAGE

    Always after 4 version oracle numbers and details of the OS.

    Post any request outside has put between.

      \

    Tags

    Mark your questions answers if you give the answer

    Password for the SYS user on primary and standby must be the same. Copy the master password for the backup server

    SCP $ORACLE_HOME/dbs/orapwv112 : /u01/app/oracle/product/11.2/dbs/orapwdupv112

Maybe you are looking for