Unable to connect to the web services server

Unable to connect to the web services server.  It is a common error that you might see if you try to enable web services.  If you receive this message, try the following steps.

For Officejet printers

1. open the internet browser type printer IP address.

2 should bring you to the status of the printer page.

3. Select the tab network at the top.

4. left side select IPv4 under wireless.

5. under DNS address Configuration select manual DNS server.

6. for favorite enter 8.8.8.8

7. for alternate enter 8.8.4.4

8. Select apply. You can get a warning saying that this could break the connection which is very good.

9. turn the printer off for about 30 seconds and then try to enable web services.

For Photosmart printers

1. Enter the printer's IP address in a browser.

2 Select the network at the top of the page.

3. on the left, select network.

4. Select Network (IP) address

5. select manual DNS server

a. manual Preferred DNS should read 8.8.8.8

b. alternate DNS server should read. 8.8.4.4

6. Select apply you could get a fair warning select OK

I hope this helps!

Tags: HP Printers

Similar Questions

  • problem connecting to the web services server

    I tried to download the latest updates of software/firmware for my all-in-one HP Photosmart Prem C310a.

    I can't get updates or activate Web Services because it still gives me the error message "problem connect to the web services server.

    I tried everything in the section of the Web of HPs site including connection via WPS - unsucessfully problems.

    I understand that you have found impossible to connect to the server error message on your printer. I would first disconnect the router and the printer for about 1 minute. I would plug the router first then the printer. I would then try to enable web services. If not successful, and you get the same error message. I'd follow these steps.

    1 obtain the IP address of your printer
    a. This can be done by pressing the icon on the printer wireless.
    2. Enter the printer's IP address in a browser.
    3. Select the tab network at the top of the page.
    4. on the left, select network.
    5. Select Network (IP) address
    6. select manual DNS server
    a. manual Preferred DNS should read 8.8.8.8
    b. alternate DNS server should read. 8.8.4.4
    7. Select apply you could get a fair warning select OK.

  • Unable to connect to the Web Services Proxy/unused (a HP 7500 JO)

    Hello

    Here's the situation:

    Previous installer:

    .  I have connected my 7500 for the corporate network (IP = 172... series)

    .  registered the product with ePrintCenter

    .  used a PC under Windows to print (and scan) with the printer

    .  web proxy entry "webproxy.phila.gov".

    .  However, because homeland security rules, I could never work, so I just let it go

    Current situation

    .  has taken the home printer and set up on my home network, i.e.,.

    -using the 192.168.xx.xx series

    -Router broadband Netgear ' G' (1 years) set up at the 192.168.xx.254

    -SSID & encryption assigned

    -printer, the value 192.168.xx.155 (static IP address, the subnet and the gateway assigned as well)

    -My DNS is identical to the bridge and it works fine for all the internet access to this day

    -with the help of a PC and a Macbook Air to print and scan and everything works fine

    .  HOWEVER,.

    -Initially, 'web services' were active (carried over from when I was on the company neetwork?)

    ..  Are looking for, found and downloaded updates

    -When I went to hp.com ePrintCenter he showed the product as 'registered '.

    ..  He would'nt I would like to connect (with a name and a password I had used previously), or create a new account

    ..  I never remember getting an email address of the printer

    ..  and I had never been able to send anything to the printer to print because of my problem of network security

    -Yes, after trying all sorts of things, I:

    ..  I tried to get another email without success

    ..  tried to re - enable web services, but he said I need to 'proxy', and I discovered that he had always "webproxy.phila.gov."

    ..  I have reset the values by default web services and network values

    ..  I put the static IP address return address in (i.e., printer, subnet and gateway (it has nowhere to put in a DNS one))

    ..  printing and scanning to 192.168.xx.155 works fine

    ..  From my iPad AirPrint works very well

    .  BUT, I still can not online and therefore web server, web services are not enabled, therefore not ePrint

    -everytime I try, it says it needs a proxy

    - but I don't have a proxy installed on my internal home network bit

    -Comcast/Xfinity, my ISP, do not use a proxy

    So, I'm dead in the water.  I can't figure out how to get the web services enabled; I do not use a proxy, so I don't know how to go beyond this issue. How to regenerate address of the printer; and so, how do I connect an account on the ePrintCenter (or get them to send me my old account information).  I'm dead in the water and cannot use a feature most of my printer that I desperately want to be put in place and functional.

    Any help would be greatly appreciated!

    Tommy

    Problem solved, but I don't know exactly how I did it. However, I went back in and let the printer assign the IP address. Then I turned the printer off and on again. Last I kept pressing the button "Printer e-mail address", who has repeatedly failed, but then finally went through and print the 'printer' page, I quickly used to connect to the ePrintCenter and put everything in place.

    Now it's working.

  • Unable to connect to the web proxy/services

    Unable to connect to the web proxy/services used for officejet pro 8600 as well as using verizon fios actiontec router.  I tried wireless and ethernet.  Connectivity seems good.

    Resolved.  Port forwarding blocked by another application of verizonwebcamera problem.

  • Unable to connect to the Web sites security and microsoft, but internet is not working properly

    Can anyone help?
    Now, this is getting very frustrating.
    I can connect to the internet and browse most Web sites. My email works fine but I can't connect to websites www.microsoft , Norton is 'unable to connect to the Live Update server, check the internet connection' and my media center can't find my internet connection.
    What is going on?
    I have a subscription to Norton who can't find any problems. I also downloaded onecare and trojan remover, returning with a clean report.
    Please help before I go out what remains of my hair.
    What about Frank

    Hello

    You can access Microsoft.com, McAffee.com, Symatec.com? Thinking you have a conficker.

    Check with this site
    http://www.confickerworkinggroup.org/infection_test/cfeyechart.html

    Alert on the Win32/conficker virus
    http://support.Microsoft.com/kb/962007

    Protect yourself from Conficker
    http://www.Microsoft.com/security/worms/Conficker.aspx

    How to remove the worm Downadup Conficker (Uninstall Instructions)
    http://www.bleepingcomputer.com/virus-removal/remove-Downadup-Conficker

    How to manually remove the Conficker worm
    http://www.411-spyware.com/Conficker-worm-removal#how-to-remove

    BDTool to remove
    http://www.bdtools.NET/

    -----------------------------------------------

    Run the malicious Microsoft removal tool, scan with Malwarebytes, Prevx to be sure you know all the
    malware involved and if necessary use UnHackMe.

    Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

    You should get this tool and its updates via Windows Update - if necessary, you can download it here.

    Download - SAVE - go where go out you there - top - right click RUN AS ADMIN
    (Then run MRT as shown above.)

    Malicious removal tool from Microsoft
    http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

    Malwarebytes - a scanner at the request - update on the updates tab and run whenever you think malware.
    http://www.Malwarebytes.org/

    Here are some free online scanners to help the

    http://www.eset.com/onlinescan/

    http://www.Kaspersky.com/virusscanner

    Other tests free online
    http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

    also install Prevx to be sure that it is all gone.

    Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs. It comes
    a scan only, VERY EFFICIENT, if it finds something to come back here or use Google to see how to remove.
    http://www.prevx.com/

    Choice of PCmag editor - Prevx-
    http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

    --------------------------------------------

    Also do to the General corruption of cleaning.

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------

    Run Malwarebytes when you can.

    IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

    IE - Tools - Internet Options - Security - reset all Zones by default level - apply / OK

    Close IE

    IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
    "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

    Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
    are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

    Could be that a BHO - BHOremover - free - standalone program, needs no installation, download and run - not all
    are bad, but some can cause your question. (Toolbars are BHO)
    http://securityxploded.com/bhoremover.php

    Startup programs
    http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

    Don't forget to do:

    Logon as administrator

    Start - type in the search box-> COMMAND - find on the list above - CLICK RIGHT - RUN AS ADMIN

    Enter each of these one at a time and press ENTER after each

    ipconfig/flushdns

    nbtstat-r

    nbtstat - RR

    netsh int Reinitialis

    netsh int ip reset

    netsh winsock reset

    Reset
    ------------------------------------------------------

    Here are a few rootkits if it were a question:

    SpyDLL Remover - free
    http://securityxploded.com/spydllremover.php

    Advanced Windows Service Manager
    http://securityxploded.com/winservicemanager.php

    Run the Rootkit Revealer - free
    http://TechNet.Microsoft.com/en-us/Sysinternals/bb897445.aspx

    UnHackme - trial
    http://www.Greatis.com/UnHackMe/

    This shows how to use UnHackme and includes a link to version 2.5 – use it as a guideline and current
    available as version above is 5.5
    http://safecomputing.umn.edu/guides/scan_unhackme.html

    IceSword - free
    http://www.AntiRootkit.com/software/IceSword.htm
    Instructions and pictorial
    http://securityxploded.com/IceSword.php
    Tutorial for use of IceSword
    http://translate.Google.com/translate?hl=en&SL=zh-CN&u=http://soft.zol.com.CN/2004/0803/145163.shtml&prev=/search%3Fq%3Dicesword%26hl%3Den%26lr%3D

    Revo Uninstaller - free
    http://www.revouninstaller.com/

    I hope this helps.

    Rob - bicycle - Mark Twain said it is good.

  • ORA-17629: unable to connect to the remote database server

    Hello

    I have put Dataguard in place with primary and 1 physical standby for learning/test database:

    I do NOT plan the unloading of RMAN backups on the physics of the day before.

    Recorded the primary database with RMAN and when "resync catalog db_unique_name all;" is issued.
    I get the following error:
    ---------------------------------------------------------------------------------------------------------------------
    RMAN > catalog resync db_unique_name all;
    from full resynchronization of the recovery catalog
    full complete Resync
    resynchronization of data base with DB_UNIQUE_NAME ASTTESTB
    RMAN-00571: ===========================================================
    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
    RMAN-00571: ===========================================================
    RMAN-03002: failed to db_unique_name resynchronization command at 28/09/2011 11:34:23
    ORA-17629: unable to connect to the remote database server
    ORA-17628: Oracle 17629 error returned by remote Oracle Server
    ------------------------------------------------------------------------------------------------------------------
    Configuration of RMAN for the main proceedings are the following:

    RMAN > show all to db_unique_name asttest;

    RMAN settings for database with db_unique_name ASTTEST are:
    CONFIGURE RETENTION POLICY TO RECOVERY OF 7-DAY WINDOW;
    CONFIGURE BACKUP OPTIMIZATION # by default
    SET UP DEFAULT DISK DEVICE TYPE; # by default
    CONFIGURE CONTROLFILE AUTOBACKUP # by default
    CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO "%F" # by default
    SET UP THE DEVICE TYPE DISK PARALLELISM 1 BACKUP BACKUPSET TYPE; # by default
    CONFIGURE BACKUP OF DATA TO DISK FILE TYPE DEVICE TO 1; # by default
    CONFIGURE BACKUP ARCHIVELOG FOR DEVICE TYPE DISK TO 1; # by default
    CONFIGURE MAXSETSIZE TO UNLIMITED; # by default
    CONFIGURE ENCRYPTION OF DATABASE # by default
    CONFIGURE THE ENCRYPTION ALGORITHM "AES128"; # by default
    CONFIGURE COMPRESSION ALGORITHM 'BASIC' AND 'DEFAULT' LIBERATION OPTIMIZE FOR TRUE LOAD; # by default
    CONFIGURE DB Nom_unique "asttest" CONNECT IDENTIFIER ' ASTTEST. UMDNJ. EDU'; _
    CONFIGURE DB "Asttestb" of nom_unique CONNECT IDENTIFIER "asttestb"; _
    CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON ALL STANDBY;
    CONFIGURE SNAPSHOT CONTROLFILE NAME TO ' / opt/oracle/product/11.2.0/dbhome_1/dbs/snapcf_asttest.f'; # by default

    Configuration of RMAN for instance physical standby are:

    RMAN > show all to db_unique_name asttestb;

    RMAN settings for database with db_unique_name ASTTESTB are:
    CONFIGURE RETENTION POLICY TO RECOVERY OF 7-DAY WINDOW;
    CONFIGURE BACKUP OPTIMIZATION # by default
    SET UP DEFAULT DISK DEVICE TYPE; # by default
    CONFIGURE CONTROLFILE AUTOBACKUP ON;
    CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO "%F" # by default
    SET UP THE DEVICE TYPE DISK PARALLELISM 1 BACKUP BACKUPSET TYPE; # by default
    CONFIGURE BACKUP OF DATA TO DISK FILE TYPE DEVICE TO 1; # by default
    CONFIGURE BACKUP ARCHIVELOG FOR DEVICE TYPE DISK TO 1; # by default
    CONFIGURE MAXSETSIZE TO UNLIMITED; # by default
    CONFIGURE ENCRYPTION OF DATABASE # by default
    CONFIGURE THE ENCRYPTION ALGORITHM "AES128"; # by default
    CONFIGURE COMPRESSION ALGORITHM 'BASIC' AND 'DEFAULT' LIBERATION OPTIMIZE FOR TRUE LOAD; # by default
    CONFIGURE DB Nom_unique "asttest" CONNECT IDENTIFIER ' ASTTEST. UMDNJ. EDU'; _
    CONFIGURE DB "Asttestb" of nom_unique CONNECT IDENTIFIER "asttestb"; _
    CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON ALL STANDBY;
    CONFIGURE SNAPSHOT CONTROLFILE NAME TO ' / opt/oracle/product/11.2.0/dbhome_1/dbs/snapcf_asttest.f'; # by default

    ----------------------------------------------------------------------------------------------------------------------

    When I tested missing missing datafile and control file scenario on the primary database, it worked (Advisor to recover data)

    However, missing datafile scenario does not work on the physics of the day before.
    Here are the steps I followed:
    ********************************************
    1 renamed a file of physical data - in standby mode:

    bash - $3.2 ls - ltr

    Total 107832

    -rw - r - 1 oracle oinstall 52429312 16 September 12:19 asttest_redo03.log

    -rw - r - 1 oracle oinstall 61874176 Sep 29 15:41 asttest_temp01.dbf

    -rw - r - 1 oracle oinstall 52436992 5 Oct 11:00 rmandg_data01.dbf

    bash - $3.2 mv rmandg_data01.dbf rmandg_data01.dbf_old

    bash - $3.2 ls - ltr

    Total 107832

    -rw - r - 1 oracle oinstall 52429312 16 September 12:19 asttest_redo03.log

    -rw - r - 1 oracle oinstall 61874176 Sep 29 15:41 asttest_temp01.dbf

    -rw - r - 1 oracle oinstall 52436992 5 Oct 11:00 rmandg_data01.dbf_old


    2. restore the datafile (find the data file # view v$ recover_file):
    RMAN > restore datafile 5;



    From restoration to 5 October 11

    Segmentation fault


    3. in spite of the error, published "recover datafile command.

    4 RMAN > recover datafile 5;



    From pick up to 5 October 11

    allocated channel: ORA_DISK_1

    channel ORA_DISK_1: SID = 10 type of device = DISK

    RMAN-00571: ===========================================================

    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.

    RMAN-00571: ===========================================================

    RMAN-03002: failure of the command recover at 05/10/2011 12:00:40

    RMAN-06094: datafile 5 must be restored.


    5. manually copy the physical primary datafile - in standby mode, & then problem recover RMAN command:
    bash - $3.2 scp oracle@msudrainier:/ora03/oradata/asttest/rmandg_data01.dbf.

    rmandg_data01.dbf 100% 50 MB 16.7 MB/s 00:03

    bash - $3.2 ls - ltr

    Total 159096

    -rw - r - 1 oracle oinstall 52429312 16 September 12:19 asttest_redo03.log

    -rw - r - 1 oracle oinstall 61874176 Sep 29 15:41 asttest_temp01.dbf

    -rw - r - 1 oracle oinstall 52436992 5 Oct 11:49 rmandg_data01.dbf_old

    -rw - r - 1 oracle oinstall 52436992 5 Oct 12:01 rmandg_data01.dbf


    RMAN > recover datafile 5;



    From pick up to 5 October 11

    using channel ORA_DISK_1



    RMAN-00571: ===========================================================

    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.

    RMAN-00571: ===========================================================

    RMAN-03002: failure of the command recover at 05/10/2011 12:01:59

    RMAN-06067: RECOVER the DATABASE required with a backup control file or created


    6. of course RMAN commands have failed to restore the missing data file;
    So I renamed the file to original and rebooted repeat services applies - this restore the data file and now the configuration state of the DG is normal.
    *********************************************************************************

    Not quite sure if I'm still he hands the right way or if the error above is related to RMAN not able to synchronize with the physics of the day before.

    The documentation I want to talk to is here (1 paragraph):

    [http://download.oracle.com/docs/cd/B28359_01/server.111/b28294/rman.htm#BAJDFBDD | http://download.oracle.com/docs/cd/B28359_01/server.111/b28294/rman.htm#BAJDFBDD]


    Any pointers/direction and advise is greatly appreciated.

    Best regards
    NK

    I got it!

    /home/oracle:STANDBY >$ORACLE_HOME/bin/rman target sys/ catalog /@rcatalog

Recovery Manager: Release 11.2.0.1.0 - Production on Fri Oct 7 14:12:10 2011

Copyright (c) 1982, 2009, Oracle and/or its affiliates.  All rights reserved.

connected to target database: PRIMARY (DBID=1562898590, not open)
connected to recovery catalog database

RMAN> resync catalog from db_unique_name all;

resyncing from database with DB_UNIQUE_NAME PRIMARY
starting full resync of recovery catalog
RMAN output not resynced for database with DB_UNIQUE_NAME PRIMARY
full resync complete

    If the necessary connection string a target/sys and a catalogue

    RMAN target sys / catalog /@rcatalog

    I did my standby

    Will try the primary

    Best regards

    mseberg

    Work on both. Great question!

    connected to target database: PRIMARY (DBID=1562898590)
connected to recovery catalog database

RMAN> resync catalog from db_unique_name all;

starting full resync of recovery catalog
full resync complete

resyncing from database with DB_UNIQUE_NAME STANDBY
RMAN output not resynced for database with DB_UNIQUE_NAME STANDBY

RMAN>

    Published by: mseberg on October 7, 2011 14:16

    Thanks a ton for sticking to it. I'll add this little thing to my web site.

    Published by: mseberg on October 7, 2011 14:22

  • Unable to connect to the software update server (127.0.0.1)

    I'm under El Capitan 10.14.4

    I'm unable to view or download from the App store apple updates. Everything else in the app store works fine except the updates and the updates, I get 3rd party updates, but nothing from apple. If I click on updates at the top of the app store icon I get the following error

    Troubleshooting steps I went through far

    • I restarted my mac a few times
    • I did some research on Google and messages more speak of iworm, fortunately I could find no trace of an infection by the worm, I scanned my machine using Sphos and ClamXav and haven't found anything relating to iWorm. I am also unable to find all the files, he leaves behind him, so I think I'm safe in this regard.
    • I checked the hosts file and there are no entries that should not be there, hosts file is copied below.

    # Database host

    #

    localhost # is used to configure the loopback interface

    # When the system boots.  Do not change this entry.

    ##

    127.0.0.1 localhost

    255.255.255.255 broadcasthost

    : 1 localhost

    • The /var/log/install.log which appear relevant lines are;

    May 26 09:44:02 macbook-pro softwareupdated [435]: SUScan: Scan for pid 435 client (/ System/Library/CoreServices/Software Update.app/Contents/Resources/softwareupdated)

    May 26 09:44:02 macbook-pro softwareupdated [435]: SUScan: out of time scan = 0.2

    May 26 09:44:02 macbook-pro softwareupdated [435]: SUScan: error in scan: error Domain = NSURLErrorDomain Code =-1004 'unable to connect to the software update server (127.0.0.1)." UserInfo = {NSErrorFailingURLKey =http://127.0.0.1/content/catalogs/others/index-10.11-10.10-10.9-mountainlion-lio n-snowleopard - leopard.merged - 1_disabled.sucatalog, SUCatalogFetchOverrideURLString =http://127.0.0.1/content/catalogs/others/index-10.11-10.10-10.9-mountainlion-lio n-snowleopard - leopard.merged - 1_disabled.sucatalog, NSLocalizedRecoverySuggestion = check that your network connection is working normally.} {If there is no problems with your connection, contact your network administrator for assistance., NSLocalizedDescription = can connect to the software update server (127.0.0.1)., SUErrorRelatedCode = SUErrorCodeScanCatalogNotFound, SUErrorUpdateServerName = 127.0.0.1, NSErrorFailingURLStringKey =http://127.0.0.1/content/catalogs/others/index-10.11-10.10-10.9-mountainlion-lio n-snowleopard - leopard.merged - 1_disabled.sucatalog, _kCFStreamErrorDomainKey = 1, _kCFStreamErrorCodeKey = 61}

    May 26 09:44:02 macbook-pro softwareupdated [435]: Scan received the error unable to connect to the software update server (127.0.0.1).

    May 26 09:44:02 macbook-pro softwareupdated [435]: updates marked ramps

    • I can ping swscan.apple.com and she is resolved to 17.164.1.22 which is the same IP that also resolves the mac next to me (which gets the update)
    • I cannot telnet on port 443 to swscan.apple.com and it connects.
    • I have a mac in yosemite next to me who can see the updates so I suspect that doesn't pose any problems with the service itself rather something on why machine.
    • I started in safe mode, and while in safe mode, I get the same error.

    I am at a complete loss what to do next short of wiping and restore from a time machine backup, can anyone help please

    You can try to disable the Sophos websheild and ClamXav if she has one. Even better would be to uninstall both and test.

    FWIW, it is never a good idea to have 2 av programs installed.

  • Pavilion 140 550 - t: unable to connect to the windows service

    Not sure if it's the good advice of post, but here goes.

    Just got the HP computer yesterday and installed Norton Security, Malwarebytes, and Windows Live Mail (do not like the version of Mail). Now, when I start it, I get "Unable to connect to the Windows Service" pop up and WLM crashes when I try to open it. What the DEVIL?

    Had the same problem on the one I just replaced. My laptop became the 'Group Policy' error thing, but I think I fixed it.

    Any suggestions? Windows is a joke!

    If it is Norton Security, then it's a firewall as well and firewalls blocking things, it's that they are supposed to do. So demand for three, you said that this is probably the cause.

    But if you do not want to test it, then try the system restore I've mentioned or reload the image origin, then just put in place the email again and see if it works without the other two installed, first to see if it will work with anything else in the picture.

  • When you try to connect from my vista desktop to my laptop windows 7 through the DRC I get the error "unable to connect to the gateway terminal server."

    problems of the DRC of vista for windows machine 7

    I have 2 computers running on a homegroup. When you try to connect from my vista desktop to my laptop windows 7 through the DRC, I get the error "unable to connect to the gateway terminal server."   Can I remotely from the laptop to the desktop vista end. I the DRC 7 is installed on the desktop and tried to connect using the IP as well as the name of the machine but still no joy.

    can someone shed light on this please?

    Hello

    Temporarily disable the security software on both computers and check if it makes a difference.

    http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

    Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  • Unable to connect to the local MySQL server through socket ' / var/lib/mysql/mysql.sock' #2 #.

    I received an email indicating that HP does not show me as having all printers which explains why I have not received information of driver update I guess.  But when I typed in HP4500 G510, I received the following error message:

    Unable to connect to the local MySQL server through socket ' / var/lib/mysql/mysql.sock' #2 #.

    And since I don't know beans about computers, I don't have any idea what it means.

    Because I had to pick a topic, I chose the one above, but no other choices were nowhere near cover.

    Hi mac64.
    I understand you are trying to register for updates for your Officejet 4500. I can certainly help you with this.

    I'll give you a link to try to register for driver updates. Please let me know if it's the same link you used and if this works differently for you, simply click on the following link: the HP driver updates.

    Hope to hear from you soon

  • DOUBLE DB: ORA-17629: unable to connect to the remote database server

    [oracle@ora11g1 ~] $ export ORACLE_SID = sales
    [oracle@ora11g1 ~] $ rman target sys/sales@sales

    Recovery Manager: release 11.2.0.1.0 - Production Wed Jun 5 13:00:15 2013

    Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.

    connected to target database: SALES (DBID = 690066655)

    RMAN > Connect auxiliary sys/salestby2@salestby2

    connected to the auxiliary database: SALES (not mounted)

    RMAN > CURRENT SPFILE DATABASE of TARGET duplicate FOR THE EVE OF the DATABASE
    2 > DB_NAME SET = 'sales '.
    3 > SET DB_UNIQUE_NAME = "salestby2".
    4 > control_files='/u02/oradata/salestby2/control01.ctl','/u02/oradata/salestby2/control02.ctl SET'
    5 > SET DB_FILE_NAME_CONVERT = "/ u02/oradata/sales /", "/ u02/oradata/salestby2 / '.
    6 > SET LOG_FILE_NAME_CONVERT = "/ u02/oradata/sales /", "/ u02/oradata/salestby2 / ';

    From duplicate Db 5 June 13
    using the control file of the target instead of recovery catalog database
    allocated channel: ORA_AUX_DISK_1
    channel ORA_AUX_DISK_1: SID = 20 type of device = DISK

    content of Script memory:
    {
    backup that copy reuse
    TargetFile ' / auxiliary format of the u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwsales
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwsalestby2' targetfile
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesales.ora' auxiliary format
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesalestby2.ora';
    clone of SQL 'alter system set spfile = "/u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesalestby2.ora";
    }
    execution of Script memory

    From backup 5 June 13
    allocated channel: ORA_DISK_1
    channel ORA_DISK_1: SID = 58 type of device = DISK
    RMAN-03009: failure of the backup command on the channel ORA_DISK_1 at 05/06/2013 13:05:26
    ORA-17629: unable to connect to the remote database server
    ORA-17627: ORA-01017: name of user and password invalid. connection refused
    ORA-17629: unable to connect to the remote database server
    continue other job steps, not a not working will not re-run
    RMAN-00571: ===========================================================
    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
    RMAN-00571: ===========================================================
    RMAN-03002: failure of Db in dual at 05/06/2013 13:05:27
    RMAN-03015: an error has occurred in the script stored memory Script
    RMAN-03009: failure of the backup command on the channel ORA_DISK_1 at 05/06/2013 13:05:27
    ORA-17629: unable to connect to the remote database server
    ORA-17627: ORA-01017: name of user and password invalid. connection refused
    ORA-17629: unable to connect to the remote database server

    Welcome to the oracle forums!

    Please take the time to go through [url https://forums.oracle.com/forums/ann.jspa?annID=1535] FAQ PAGE

    Always after 4 version oracle numbers and details of the OS.

    Post any request outside has put between.

      \

    Tags

    Mark your questions answers if you give the answer

    Password for the SYS user on primary and standby must be the same. Copy the master password for the backup server

    SCP $ORACLE_HOME/dbs/orapwv112 : /u01/app/oracle/product/11.2/dbs/orapwdupv112

  • ADF / integration OBIEE: unable to connect to the presentation BI server

    Hello
    Using JDeveloper 11.1.1.6, I created an ADF application to test its integration with OBIEE 11.1.1.6. The request contains the jsf page that holds the OBIEE dashboard. Next, OBIEE, I created impersonate user. When I run this application on Weblogic Server built-in, it shows dashboard OBIEE perfectly. But when I deploy the application on weblogic OBIEE server, deployed with success but shows following error when we try to access the application via a URL.

    Unable to connect to the presentation BI server. Please ensure that it is running, configured correctly, and that the details of the connection in this application is accurate. Please check the log file for more details.

    (Http) connection works very well when check it out us inside the app. Can you please help how to solve this problem?

    Hello
    Bad news.

    How did you create the connection? In the resource Palette?

    I noticed that I have to drag the connection in the connections of Application resources (if it is not present), I have to uncheck in the properties/deployment of applications 'Powers' and cancel the deployment of the application and redeploy with JDEV (or em)

    This connection is really not clear in my mind

  • air application connects to the web service although swf don't

    Hey there,

    I will try and be brief. We built a kiosk application in flash builder a pure as3 project. When we went to convert it into an air application all seems fine except for two issues. one is that we cannot use the Security.allowDomain("*"); Tagus. not much we comment on this possibility, but when we do we cannot connect to the web service that we use. Here is the error msg that we get:

    URL http://api.macys.com/v2/catalog/product?prodid=559529 & prodid = 586262 & prodid = 442702 & prodid = 5 39030 & prodid = 444331 & prodid = 593389 & prodid = 102435 & prodid = 519743 & prodid = 357571 & prodid = 128285 & prodid = 407708 & prodid = 209799 & prodid = 417917 & prodid = 498705 & prodid = 131858 & prodid = 597478 & prodid = 142166 & prodid = 470687 & prodid = 584020 & prodid = 167015 & prodid = 75190 & prodid = 432111 & prodid = 481224 & prodid = 549755 & prodid = 483429 & prodid = 414178 & prodid = 596422 & prodid = 385591 & prodid = 226280 & d = 142163 prodi

    ioErrorHandler: errorProductId: WebApplicationException

    ioErrorHandler: currentTarget: Error #2032: error in workflow. URL: http://api.macys.com/v2/catalog/product?prodid=559529 & prodid = 586262 & prodid = 442702 & prodid = 5 39030 & prodid = 444331 & prodid = 593389 & prodid = 102435 & prodid = 519743 & prodid = 357571 & prodid = 128285 & prodid = 407708 & prodid = 209799 & prodid = 417917 & prodid = 498705 & prodid = 131858 & prodid = 597478 & prodid = 142166 & prodid = 470687 & prodid = 584020 & prodid = 167015 & prodid = 75190 & prodid = 432111 & prodid = 481224 & prodid = 549755 & prodid =. 483429 & prodid = 414178 & prodid = 596422 & prodid = 385591 & prodid = 226280 & d = 142163 prodi

    Here is the error of charles:

    < error >

    < > 103 errorCode < / errorCode >

    types of arguments < message > Incorrect or combination < / message >

    < errorDetail > WebApplicationException() < / errorDetail >

    false < success > < / success >

    < / error >

    now, if we run just the swf file it connects very well. the only reason I need this app to be in a wrapper of the air is so that I can remove the print dialog box. otherwise, I'd create just an exe file.

    any ideas would be great!

    Thank you

    OK, found the problem!

    When we built the as3 project and we implement web service calls, we used post from get we caused problems. We have been connecting to a service of qa so that may have something to do with it. In all cases, we have changed the headers in the air application to get and it seems to work fine. Why would he works in the SWF and not the air who knows, but there are go!

    Thank you

    Jorge

  • Unable to connect via the Web client

    Dear team,

    Web customer service is installed on the SSO Server (SSO installed on seprate VM), since last year 1 it works very well, but as of today I m not able to connect through webclient get below error

    https://SSO.test.com:9443 / vsphere client / #.

    Unable to connect to the server vCenter Single Sign On https://SSO.test.COM:7444/ims/STSService? wsdl .

    Note: I am able to connect VC via vsphere client but not to Web client.

    concerning

    Mr. VMware

    After you restart the WebClient service, wait 5 minutes. Now, I m able to connect VC via the web client.

    Thanks for all the help and support.

  • HP Photosmart 5520 - problems with the connection to the web service

    Hi, I'm trying to run the web service on Hp Photosmart 5520, but it does not work. Wireless printing works well, but he says that it cannot connect to the server and sometimes requires adding a proxy.

    I've set up a fixed IP and I used it in the IP (manual ip) configuration, I've implemented manula and gateway subnet mask (using the address of my router). I used the same primary DNS preferred (but also tried 8.8.8.8 and others)

    No question.

    Currently, I removed all of the proxy page. The error I get says that it cannot communicate with the server.

    Thanks in advance

    .. don't ask me what happened... while I was writing this worked
    Thanks anyway

Maybe you are looking for