Unable to connect to the WLAN router satellite P300

Similar Questions

• Satellite A110-195 unable to connect to the WLan router

  Hello

  I have a wifi router and I have connected my laptop and it worked wery well but on low there is I could not conect to router but woudn't ip address pop up. Internet access was not.
  I am connected to the same router another device and it worked...

  Hello

  Believe me, there is no general solution, you must check all the settings of your operating system

  First of all that I recommend to check the parameters of the TCP/IP protocol if everything is settled automatically on.
  Then check if you are using encryption parameters right as standard (WEP, WPA, WPA2) encryption and the encryption key.

  It s also advised to reinstall or update the Wlan card driver

  If you used the windows own WLan configuration, I would recommend testing as Atheros Client utility or Intel ProSet Wlan client configuration utility. But it depends on the WLan card what client WLan configuration utility can be used

  concerning

• Satellite Pro 6100 - unable to connect to the WLAN router

  Hello

  I brought a 2nd hand Satellite Pro, model version SP6100 (PS610E-029ZV-EN), P4 1.7 Ghz, 512 MB, 30 GB, with Windows 2000 Pro loaded.

  I can't connect to my wireless router. The switch is in the correct position.

  I want to change to XP using the key provided with the new laptop (dual OS) however I can't reformat using a XP disc at the start up or if I use the recovery cd (start with holding C and let go when he works up) it starts but displays 'specification drive not valid' three times and charges Win2000.

  Can someone advise how (or if!) Can I reformat I want?

  Any help will be greatly appreciated.
  See you soon.

  Are you sure that the wireless network adapter has been installed in the laptop?
  Check in Device Manager

  On some series WLan is optional. This means that the WLan card is not installed, but it is possible to install an and, consequently, the laptop contains the WLan switch.

• Qosmio X 300-13 G - unable to connect to the WLan router using Project N

  Hello
  I purchased a Qosmio X 300-13 g (the only one available in Portugal :/) and I tried to connect it to a network wirelles N, but I always get an error message):
  Windows could not connect because the defenitions of the router are different from your...

  Well you know why? I tried with several routers, and it is always the same...

  TKS

  Concerning

  Is your WLan router supports 802.11 N draft standard?

  Did you choose N draft standard on your WLan router?

• Equium L10-200 - unable to connect to the WLan router

  I have a 200 L10
  When I tried to connect WiFi my suburb does not connect with the router at all. Looks like it was trying to access the Internet.
  Then window took to replace my IP address. But as I can not connect on it cannot be a substitute.

  How can I get them back.
  Cable and work for laptop computer to my wife on the same router work ok.

  I am running XP and connect to the sky

  Hey mate,

  Why you can t replace your IP address?
  First to connect properly, check if you need a static IP address or if you get an IP address from your router (DHCP).

  If you use encryption, make sure you typed the correct password. Disable filtering of MAC addresses in the router to connect properly.

  Last but not least, make sure that you have installed the new firmware on your router.

• Satellite P200 - unable to connect to the WLAN router

  I have a Satellite P200 and that you have upgraded from Vista to Windows 7.

  The wireless is working and to see available networks, but trying to connect it does not ask the WEP key, it just says: he has a connection problem and (possibly) says that it cannot connect.

  Someone at - it clues on this?

  Thank you.

  Hello!

  It's really strange Mavourneen. I also have Windows 7 on my Toshiba laptop, but I put t have problems to connect to my router WLAN. Everything works fine on it.

  Can I ask you if you tried to update the driver WLAN? You can download the latest version here:
  http://APS2.toshiba-tro.de/WLAN/

  Have you tried to update the BIOS?

• Satellite L500D - unable to connect to the WLAN router

  Hey all,.

  Hoping that someone here will be more help. For some reason, my laptop won't connect to a wireless network today and it was working fine yesterday.
  When I troubleshoot I get: there might be a problem with the wireless network connection card

  I called belkin and the Lady reset our wireless under a new name which we I = didn t need that my roommate who has vista had no problems with his internet. When I connect the cable through my laptop, I have internet

  Now that I see there no button on my phone to activate the wireless it connected always automatically and the led is on.

  Hi Ren,

  In the wireless issues forum, you can find hundreds of discussions on different WLAN problems.
  Did you check that?
  I think that you will find your answer.

  According to your assignment on resets the router I think that it s properly configured. Check the router security options if the SSID is visible and then encryption and password. Also, make sure that the MAC address filtering is not enabled.

• My ZTE open C unable to connect to the wlan with 63-signs-hex key.

  Hello

  my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.

  Oliver

  Hi OliverwithZTE,

  I understand that you have connection problems to your network WPA2-PSK.

  Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.

  -Ralph

• Satellite L40 - 14N does not connect to the WLan router

  Bought two portable Satellite L40 - 14N as Christmas gifts and one of them does not connect to the wireless router.
  Is the error that says "error message unknown" try please login again.

  The wireless network appears in the list of networks available with a strong signal. Notepad attempts to connect but the error 'wireless link failed for an unknown reason. " Made a comparison with the other laptop that works very well and the configurations appear to be identical!

  Tried it on wireless network from a friend with the same result. All suggestions, am pulling out my hair at this point.

  Seems to be a Vista issue.

  I found this article Ms knowledge base:
  http://support.Microsoft.com/kb/928233/en-us

  You need to add a value in the Windows registry.

  1. Click Start, type regedit in the search box, and then click regedit
  list programs.

  2. Locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE es\Tcpip\Parameters\Interfaces\ {GUID}
  This registry path, click the (GUID) subkey that corresponds to the
  Network adapter that is connected to the network.

  3. on the Edit menu, point to new, and then click DWORD (32-bit) value.

  4 new value #1, enter DhcpConnEnableBcastFlagToggle, then
  Press ENTER.

  5. right click on DhcpConnEnableBcastFlagToggle, then click on modify.

  6. in the value data box, type 1 and then click OK.

  7. close the registry editor.

  concerning

• Satellite A105 - unable to connect to the wireless router more

  I had the success of connection to a router Wireless Linksys for the last few months. Today, that I couldn't connect to the Linksys still another. A few times I have to connect to the Linksys router, but I got a weak signal so I would be disconnected. The green bars on the router Linksys under available networks are all solid green full bars, but I can't? t connect.

  To do or check to login once more?
  Thank you

  HM, you will need to do some research! What was the last you´ve installed applications? Installed new drivers/tools/software on your computer?
  If not you already installed the latest drivers for the chip wireless for your laptop? If not already done, then try it and Don t forget to update BIOS. :)

  If anything brought success then just to give a few comments. :)

  Welcome them

• Unable to connect to the Internet my Satellite L300-1 to 6

  Hello

  I have a problem with my Satellite L300-1 to 6. When I try to connect to the internet I plugged taking LAN my slot for LAN card and when the identification process of the network in "Network and sharing Center" to the State of the connection write "Unindeficated Network" and I cannot access the internet...
  And this is happen when I use automatic receives the IP parameters... ?

  When I try to solve this problem with the manual configuration TCP/IP settings in the status bar indicates that I have an internet connection but when I try to open the WEB site I see the error message «...» CAN NOT COMMUNICATE WITH THE SYSTEM (DNS).

  Please explain to me how to fix this...?

  P. S. The network on my other PC works normally... ? On my L300, I use Windows Vista Home Premium SP2 and on my other PC, I use Windows XP Pro... ? !

  Hello

  Usually, the WLan router supports a range of IP addresses and everything should be set to automatic.

  In my opinion, you should first check the settings of the WLan router.
  Take the router manufacturer news and read the manual of the router how to set up the router.

  After the router has been configured correctly, you should go to connections-> LAN (local network connection) and need to access the properties of the TCP/IP protocol.

  Here, you must make sure that the IP address and DNS are set to obtain an address automatically

  That's the whole secret.

• Equium M50 connect to the WLan router only when security is disabled

  MY Equium M50 will connect to my ROUTER BELKIN g only MIMO when security is disabled.

  What is the reason for this please?

  Blonde bimbo!

  Hello

  Did you mean WiFi encryption that blocks the entrance to the local wireless network?
  I suppose that you have set the encryption (WPA, WEP, etc...) on your router WLan but didn't configure the wireless network adapter.

  Well, in my opinion, you should check out what WLan encryption makes the card holder and then choose it on the WLan router. The encryption key must be set to the router and the laptop!

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• Satellite L505-12 q - unable to connect to the Wlan on Draft N Router

  Hello.

  I have a Toshiba Satellite L505-12 q who that I connect to router Edimax br 6524n.

  My problem is that when I connect to the router the laptop does not use n 802.11 g... The network card is Realtek RTL 8191se... He supports the project and it is configured to receive B G and N. When I set up the router to use only the band N the portable project sees the network, but when I try to conect it can not...

  Can someone tell me where is the problem?
  I updated the firmware on the router and adapter driver and still nothing good... :|

  Thank you.

  Post edited by: Matt1990

  Hello

  First you need to update the WLan driver.
  Here is a page with all the drivers:
  http://APS2.toshiba-tro.de/WLAN/

  After that, go to Device Manager-> properties-> Advanced tab WLan card and check if the Draft N has been selected.

  Restart the device and then try again

• Satellite A500 - unable to connect to the WLan

  I'd like someone to help me.

  Have recently bought a satellite A500.
  I'm new in the world of laptops so I'm wrong.
  I connected to a router via a modem, the two netgear, the news.

  Had the two config for my network. Works well as long as ethernet is connected to the router of computer.

  My wireless icon on the front of the laptop is orange.
  If this should be green as the router?

  Pressing FN f8 it tell me wireless is connected.
  When I remove the ethernet cable it tell me to fix the problem, I need to plug in the ethernet cable.
  But I want to go wireless, I'm sure I'm missing something.

  Rang netgear but after that my router and it is not connected to wireless technology they could help me more.
  I use windows7.

  Thanks to anyone who can help me.

  > My wireless icon on the front of the laptop is orange.
  > Should it be green as the router?

  The WLan led can only be ON or OFF. If the light comes on (any color) then it means that the Wlan switch is on!

  It seems that the WiFi is enabled. In this case, you will need to properly configure the WiFi network.
  You can use the own WLan settings in Windows or a Wlan configuration tool like Intel ProSet utility.

  First need choose the right SSID (wireless network name), right of encryption (WEP, WPA, etc.) and password encryption.
  Please note that all of these parameters should be the same on the router WLan and WLan configuration software!

  Please check if the firewall does not affect the connection to the internet as well!

  PS: make sure you use the latest version of the WLan driver
  Here you can find the drivers:
  http://APS2.toshiba-tro.de/WLAN/

  In addition, search and read comments here on the forum!