Unable to connect using the Cisco VPN client

Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

I enclose the relevant configuration information in the attachment. Any help is welcome.

Depending on the version, add...

ISAKMP nat-traversal

or

ISAKMP nat-traversal crypto

Should be all you need.

Tags: Cisco Security

Similar Questions

  • Unable to connect via the Cisco VPN Client

    Hello

    I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

    I am not able to connect and watch the journal on the SAA

    ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

    ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

    ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

    What could be the reason.

    Concerning

    Hi, I had this same problem, here is the solution:

    When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

    Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

    Well, change your strategy using MD5 isakmp / OF would do the trick.

  • Unable to connect to the Cisco VPN you use native client: El Capitan

    I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."

    When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:

    * connect using the old work VPN connection: without success

    Config: Hand [server address, account name],

    AUTH settings [shared secret, the Group name].

    Advanced [mode to use the passive FTP = TRUE]

    errors:

    "authd [124]: copy_rights: _server_authorize failed.

    "raccoon [2580]: could not send message vpn_control: Broken pipe"

    ...

    * Add new VPN connection using L2TP over IPSec: without success

    Config: Hand [server address, account name],

    Authentication settings [user authentication: password, identification of the Machine: Shared Secret].

    Advanced [send all traffic on the VPN = TRUE]

    errsors:

    "pppd [2616]: password not found in the system keychain.

    "authd [124]: copy_rights: _server_authorize failed.

    ...


    * Add new connection using Cisco via IPSec VPN: without success

    Main config: [server address, account name].

    AUTH settings [shared secret, the Group name].

    Advanced [mode to use the passive FTP = TRUE]

    errors:

    "authd [124]: copy_rights: _server_authorize failed.

    "raccoon [2580]: could not send message vpn_control: Broken pipe"

    VPN server is high and does not work and accepts connections, this problem is entirely on the client side.

    I. Journal of Console app existing/Legacy VPN connection:

    26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics

    26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]

    26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status

    26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.

    26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

    26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

    26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 339 [2580]: connection.

    26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

    26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

    26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.

    26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 405 [2580]: connection.

    26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

    26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

    26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

    26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

    26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

    26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

    26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

    26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

    26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.

    [26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting

    26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).

    26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

    26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

    26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

    [26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no

    26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    $VPN_SERVER_IP

    II. new VPN connection using L2TP over IPSec Console app log:

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856

    26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856

    26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13

    26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent

    26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

    26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

    26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]

    26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status

    26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory

    26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]

    26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller

    26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller

    26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.

    26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.

    26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain

    26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!

    26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!

    26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501

    26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback

    26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback

    26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed

    26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify

    III. New connection of Cisco VPN through IPSec Console app log:

    26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

    26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

    [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]

    [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status

    26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.

    26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed

    26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

    26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

    26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 296 [2576]: connection.

    26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

    26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

    26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 374 raccoon [2576]: connection.

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

    26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

    26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

    26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

    26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

    26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

    26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

    26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

    26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.

    [26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting

    26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).

    26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

    26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

    26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

    [26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no

    26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    It seems that I solved the problem, but I'm not sure it helped.

    After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.

  • Unable to connect to the Cisco VPN using the branch line

    Hello

    We use Cisco VPN Client 5.0.07.0290 to connect to our servers. We have a Sonicwall NSA2400 FW and we have 2 ISPS. We have configured load balancing on firewalls in mode 'Spill-Over '.

    So whenever the 1st line is on full charge, it will automatically moves users on the 2nd line.

    The problem that we face here is the users who get 1st line ISP, they can easily connect to the client VPN Cisco IP, but the users who receive the IP of the 2nd line of the ISP, they are not able to connect to the Cisco VPN Client. It's really annoying because everyone should be able to connect.

    It will be really great if someone can help me as well.

    Thank you

    PS: If Exchange us the line of Sonicwall haapens scenario of Vice versa as mentioned above.

    Hello Sam,.

    Correct me if I help you,.

    In your network that is inside the firewall, you are trying to connect to Cisco VPn client resides outside your network/Public network.

    If the above is the question.

    Please check the routes and roads of sonicwall priority.

    example:

    Isps1: the value of the metric as 1 for traffic destined for cisco VPn IP of the gateway and specify to leave traffic isps1 interface

    ISP2: set the metric 1 once again for the traffic to cisco VPn IP of the gateway and specify to leave traffic ISP2 interface

    interface metric 1 source destination

    Kindly, please note the useful messages and.

    Thank you

    Srikanth

  • Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

    Hello

    I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

    I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

    Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

    Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
    Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

    The router configuration

    IKE policy

    VPN strategy

    Client configuration

    Hôte : < router="" ip=""> >

    Authentication group name: remote.com

    Password authentication of the Group: mysecretpassword

    Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

    Username: myusername

    Password: mypassword

    Please contact Cisco.

    Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

    You can use the PPTP on the RV180 server to connect a PPTP Client.

    In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

  • How to connect to the CISCO VPN server without using the CISCO VPN client (from dialog Windows VPN)

    Hello world

    I have a cisco router 2800 installed in our company
    and I have it configured as a VPN server for professional help (cisco configuration)
    with the ease of the VPN Server Wizard
    Can I connect to this server using windows XP or 7 dialog VPN?

    Hello

    Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers community. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:
    http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

    I hope this helps!

  • No Internet access after the connection of the cisco vpn client

    Hi Experts,

    Please check below config.the problem is vpn is connected but no internet access

    on the computer after the vpn connection

    ASA Version 8.0 (2)
    !
    ciscoasa hostname
    activate 8Ry2YjIyt7RRXU24 encrypted password
    names of
    !
    interface Ethernet0/0
    nameif outside
    security-level 0
    IP 192.168.10.10 255.255.255.0
    !
    interface Ethernet0/1
    nameif inside
    security-level 100
    IP 192.168.14.12 255.255.255.0
    !
    interface Ethernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    2KFQnbNIdI.2KYOU encrypted passwd
    passive FTP mode
    standard access list dubai_splitTunnelAcl allow 192.168.14.0 255.255.255.0
    INSIDE_nat0_outbound list of allowed ip extended access all 192.168.14.240 255.255.2
    55.240
    pager lines 24
    Within 1500 MTU
    Outside 1500 MTU
    IP local pool testpool 192.168.14.240 - 192.168.14.250
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    NAT (inside) 0-list of access INSIDE_nat0_outbound
    NAT (inside) 1 0.0.0.0 0.0.0.0
    Route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout, uauth 0:05:00 absolute
    dynamic-access-policy-registration DfltAccessPolicy
    Enable http server
    http 192.168.14.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-md5-hmac setFirstSet
    Crypto-map dynamic dyn1 1 set transform-set setFirstSet
    Crypto-map dynamic dyn1 1jeu reverse-road
    dynamic mymap 1 dyn1 ipsec-isakmp crypto map
    mymap outside crypto map interface
    crypto ISAKMP allow outside
    crypto ISAKMP policy 1
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 43200
    crypto ISAKMP policy 65535
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH timeout 5
    Console timeout 0
    a basic threat threat detection
    Statistics-list of access threat detection
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the netbios
    inspect the rsh
    inspect the rtsp
    inspect the skinny
    inspect esmtp
    inspect sqlnet
    inspect sunrpc
    inspect the tftp
    inspect the sip
    inspect xdmcp
    !
    global service-policy global_policy
    password encrypted user testuser IqY6lTColo8VIF24 name
    username password khans X5bLOVudYKsK1JS / encrypted privilege 15
    tunnel-group mphone type remote access
    tunnel-group mphone General attributes
    address testpool pool
    tunnel-group ipsec-attributes mphone
    pre-shared-key *.
    context of prompt hostname
    Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
    : end
    ciscoasa #.

    Hello

    Large.  Try adding the below to make it work

    vpn-sheep access list extended permits all ip 192.168.15.0 255.255.255.0

    NAT (inside) 0-list of access vpn-sheep

    Harish

  • What are the ports used by the Cisco VPN Client?

    Hello

    I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

    I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

    What are the ports used by the Cisco VPN Client?

    Thank you

    You need to open:

    UDP 500

    ESP protocol

    You must also open the UDP 4500 port (if using NAT - T).

    In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

    1. If using IPSec over TCP 10000, then open TCP 10000.

    2. If using IPSec over UDP 10000, open UDP 1000.

  • Impossible to install the Cisco VPN Client on Windows 7

    Hello

    After an uninstall successful VPN Cisco version 4. I try to install the Cisco VPN Client 5.0.07.0290 version.

    But after the launch of vpnclient_setup.msi, the wizard starts. When I click on the next button, I get the following message: "installation ended prematurely because of an error".

    As an attachment, I add the details of the discovery of the error in the logs of windows (logError.txt) and the logs generated by the MSI installer in verbose (log2.txt) mode.

    My computer is a lenovo W500 with Windows 7 64-bit and 4 GB of memory (compatible with the requirements of the Cisco VPN Client).

    I have administrative privileges on this computer.

    Please help me!

    I need to use it to connect to my corporate network.

    Thanks in advance.

    BR

    Jerome

    If you want to try another software, I know that works I used it up until cisco came out with a 64-bit client there. Is the 64-bit version of shrew 2.1.0 it worked very well, you will just need your file FCP of cisco for import into if you have. This will tell you if the client or your system at least.

  • multi-site VPN with just the cisco vpn client

    Hello everyone

    Please I need your help.

    We have a headquarters office and up to 60 is BranchOffice, we want to create VPN network between its. so let's deploy 2 router cisco esy vpn server with HA (HSRP) at the Headquarters Office and all branches have Connection ADSL and they will use just the cisco vpn client to connect to the Headquarters Office.

    My question is: is it possible to do it just with the client vpn cisco without purchased for any exercise bracnh a cisco router to create an ipsec tunnel because it is so expensive?

    It depends on if the routers to offices can handle NAT with several internal VPN clients to 1 IP address. Most of the new material should be fine. Keep in mind the maximum limit of the VPN client, with 60 agencies and 5 people each of whom you are above the limit.

    Michael

    Please note all useful posts

  • How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

    Dear all

    How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

    Concerning

    Hi Imran,

    Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

    Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

    Once you create and save this profile. Your FCP file is stored.

    Please assess whether the information provided is useful.

    By

    Knockaert

  • How to allow access to a local area network behind the cisco vpn client

    Hi, my question is about how to allow access to a local area network behind the cisco vpn client

    With the help of:

    • Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
    • Cisco VPN Client version 5.0 software

    Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?

    Thank you.

    Hi Vladimir,.

    Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.

    If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.

  • Unable to connect using the current password

    Using the current password which only had 6 characters - have now changed to 8 hope if this helps solve the problem.
    Have you noticed too there was an update of Mozilla on my laptop the day before that this problem then this could be the reason?

    Unable to connect using the current password

    It is far from a complete problem description.
    Please explain in detail

    • what you were doing
    • That's happened

    Using the current password which only had 6 characters

    6 characters is a very weak password. Consider using a password manager to generate longer and more complex passwords and to remember these passwords.

  • After changing the orainventory place im unable to connect using the oracle user

    Hello

    IM using oracle 12 c on rhel 6 after correctly installing the software, I changed the location of oravinventory in/data/houses

    / u01/app/Oracle

    After making these changes im is no longer able to connect using the oracle user...

    also I back return changes I had made to the orainventory folder still unable to connect using the oracle user...

    any help on this would be greatly appreciated

    Sadia. wrote:

    Hello

    IM using oracle 12 c on rhel 6 after correctly installing the software, I changed the location of oravinventory in/data/houses

    / u01/app/Oracle

    After making these changes im is no longer able to connect using the oracle user...

    also I back return changes I had made to the orainventory folder still unable to connect using the oracle user...

    any help on this would be greatly appreciated

    Newer versions of oracle have implemented a great new technology to help solve problems, called "error messages."  Unfortunately, I can't find any reference to an error message named 'is no longer able to connect.

    And why you are moving your site from inventory?  When you have installed oracle, he put the inventory where he wanted.  There is no reason to try to change or replace.

  • Unable to connect to the Group Policy Client service

    So I know there is a lot of info on how to solve this problem, but it CONTINUES to SE. As I'll fix it then after that I closed once or twice going to do EXACTLY the same thing, it gives you the screen with Windows can't connect to the Group Policy Client service. I have windows Pro 8.1 and I never had this problem before. If you guys know how permanently repair this them please say so. I don't like going back trying to set every time. And he started after only a day and then he kept doing the same screen. It would be very useful if you could respond ASAP.

    Hello

    Thank you for the update on this issue.

    From now on, I recommend you to go through the following methods:

    Method 1:

     

    I suggest you perform the SFC scan and check if that helps. The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

    Note: System File Checker is a Windows utility that allows users to find corruptions in Windows system files and restore the damaged files.

    After the SFC scan, run Windows Update.

    Method 2:

    Make sure that all Windows updates are installed on your computer as the issue may occur because of some missing updates for Windows components.

    Please follow the steps to install the available Windows updates.

    1. Press Windows + C, type Windows Update in the start search box, and then click Windows Update in the results pane.
    2. Click find updates. When the scan finished, click optional review updates.
    3. Click the check box next to the update, and then click install updates.
    4. If you are prompted, read the license agreement, then click I agree.
    5. Follow the instructions on the screen to download and install updates. If you are prompted, restart your computer.

    If the problem persists, please answer us with the details of the issue and messages.

    Hope this information is useful. Please let us know the results to get help.

Maybe you are looking for

  • Second disk for Portege A600

    Add second HARD drive instead of the DVD in my Portege A600-157 player?

  • Upgrade CPU on Satellite P100-434

    Satellite P100-434 BIOS v 4.80 does support the Core2Duo T7500 Intel proccessor? I'm currently have T5500 and want to update to T7500, is the same thing but I don't know the motherboard/BIOS card can support this CPU? I advance thank you

  • ProBook 450 G2: ProBook 450 G2 - RAM upgrade

    Hello where can I find a list of compatible hardware for my g2 450 probook? In another thread, the link to the manual no longer works. I already bought a kingston 4 GB ram pc3-12800 sodim, but memory is not admitted by the laptop. Thank you.

  • N100 power failure!

  • No sound on my speakers

    my computer always tells me my speakers are disconnected on notice to someone else, I right click on the speaker icon, which has a red x on it, I selected reading devices, clicked on the reading tab, clicked on the speaker, but I can't click on the d