Unable to connect with the Mac computer?

Similar Questions

• Unable to connect with the PC tab

  I bought a Ubislate android 7 C + from Datawind, but unable to connect with the computer

  Burnersalvation,

  To provide the proper resolution, I would need more information on your side.

  1. which version of the operating system are you using?

  2. what happens when you try to connect to the tab?

  3. How do you connect tab to the computer?

  To connect to Android Ubislate to the computer, it may require some software to install on the computer provided by the manufacturer of the tab. Then I suggest you to contact the manufacturer of the tab to get help on this issue.

  Check out the link:

  http://www.ubislate.com/contact/index.html

  Hope this information helps. If you need more assistance or information on this question, reply to this post. I'll be happy to help you.

• Unable to connect with the MIFI device.

  I have a Verizon Jetpack 890 L mifi device and an older model Dell laptop that is wireless. After spending two hours on the phone with Verizon, finally got the correct IP address for the device to 'connect' with the computer. The States of the computer it is connected to the device, but the device shows that it of just nothing connected to it, have tested the device with a phone and the Xbox and the two front showed connected and functioning with the device. But the computer does not connect to the internet. Help, please!

  The message "the network password needs to be 40bits or 104bits depending on your network configuration. "This may be criteria such as 5 or 13 ascii characters or 10 or 26 hexadecimal characters" means that the system used encryption is WEP (instead of WPA or WPA2).  Although it is the lowest available wireless security, now that I think about it, I'm a little surprised that the mifi comes with a wireless security is enabled.

  There are at least 3 different "passwords" potentially used by your device.

  1. There may be a password that allows the device to connect to cellular service.  As far as I can tell from the manual, it is a "PIN code" that may or may not be required by your cell carrier (i.e., Verizon).  See page 15.

  2. There is a password that gets access to the configuration of the mifi utility.  This is the password that is supposed to be printed on the back of the mifi AND displayed on the LCD when the mifi is turned on.

  3. There may be a password for encryption (or "network key") wireless as the wireless mifi and your computer is configured to use WEP, WPA or WPA2.

  The more I read the manual for this device, I am convinced that the default setting for wireless encryption is 'None' and the password on the back of the device #2 above.  On the other hand, I can't imagine how he could have set himself up for the WEP encryption.

  Here are my latest suggestions.

  1 reset the mifi to factory default.  Beside the decision-making when the power cord is connected is a small button.  With the power on, press and hold this button. The manual says only: "hold."  I would like to keep the button pressed for at least 20 seconds or until there is some indication on the screen that a reset has occurred. You will need a unfolded paperclip to press the button. See http://support.verizonwireless.com/clc/devices/knowledge_base.html?id=50011#alt

  2. make sure that the battery is fully charged.

  3. turn on and confirm that the connection ('up' and 'arrows'), (e.g., 4 G LTE) service and the strength of the signal (bars) are turned on:

  

  4 wait about 10 seconds and then go to "View available wireless networks," find the one that matches your mifi (check to make sure that you do not have a neighbor with a mifi with a similar SSID) and click on connect.  You should NOT be asked for a password.

  5. open a web browser and enter the address 192.168.1.1 OR vz.hotspot in the address box and click GO.  You should see the following text:

  

  6. Enter the password of the sticker on the back of the mifi in the box and click on the button "Login".

  From there, you can follow the manual to configure wireless security settings.  Good luck.

• Remote assistance - unable to connect to the desktop computer using the remote connection

  Hello

  I'm currently running vista Professional 64 bits for portable and desktop computers.

  Problem:
  -I am not able to connect to the desktop computer by using the remote connection.

  Tried:
  -Setup the remote asstance for the Username (account login) designated
  -looked up the IP address
  -entering the IP then username and password
  Failed connection *.

  Little Question, too:
  -I run behind a router with 3 machines connected to the router, it would change my location from IP address? I think that's where I'm stuck at.

  The following article should you guide through the process and solve your problems:http://www.vistax64.com/tutorials/116361-remote-assistance.html.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• BlackBerry Z10 unable to connect to the Mac

  I can't connect to my z10 on the network. When I try it try to connect for a few minutes, and then it just says: connection failed. I then try again and put my username and password, but after a few minutes of trying to connect it fails.

  I'm on a Mac.

  Any ideas?

  EDIT: I am able to connect via USB if I disable my wireless (aka airplane Mode)

  Turn off wifi and try to connect with the usb cable

• Unable to connect to the remote computer

  Hello

  I work in an organization. I set up VPN in my computer and when I try to access a remote server, it comes with the following error:

  Remote Desktop cannot connect to the remote computer to one of the following reasons:

  1. remote access to the server is not enabled

  2. the remote computer is disabled

  3. the remote computer is not available on the network

  Make sure that the remote computer is on and connected to the network, and remote access is enabled.

  I connected several times using my computer. I had no problem. But suddenly am facing it.

  I also tried another computer and I was able to connect without any problems.

  When connected to the VPN, am able to ping the server name and IP. Am also able to connect to shared folders (\\COMPUTERNAME). But I am not able to connect to the desktop remotely using DRC (mstsc).

  Help, please!

  Thank you.

  Vignesh.

  Hello

  Thanks for posting your query in Microsoft Community.

  The Microsoft Answers community focuses on the context of use. Please reach out to the business community of COMPUTING in the TechNet forum below:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro

• Unable to connect to the desktop computer running Windows 7 laptop running Windows 7, both in my home network, using remote desktop

  My desktop (host) is running Win7 Pro and my (client) laptop is running Win 7 Home Premium. For the office, I went to the control panel and allows remote connections. When I try to connect with the laptop in my same home network, I get an error message: Remote Desktop cannot connect to the remote computer you for one of the following reasons:

  (1) remote access to the server is not enabled

  (2) the remote computer is disabled

  (3) the remote computer is not available on the network

  Now, the computer is on and I can see what he listed as one of my computers on network. In fact, I accessed the command of remote desktop by right-clicking on the desktop in the list of networks and by selecting Remote Desktop in the menu dropdown.

  Obviously, I am missing something or something wrong. Please help me to understand.

  What do you call the remote [DRC] host desktop desktop machine, IE. local LAN IP static, the laptop?

  See this help as possible...

  http://theillustratednetwork.MVPs.org/RemoteDesktopTroubleshootingChecklist.html

• Unable to connect with the listening port of the client

  [oracle@rac31 ~] $ lsnrctl status

  LSNRCTL for Linux: Version 11.2.0.1.0 - Production on March 21, 2014 03:33:30

  Copyright (c) 1991, 2009, Oracle.  All rights reserved.

  Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = LISTENER)))

  STATUS of the LISTENER

  ------------------------

  Alias LISTENER

  Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production

  Start date March 20, 2014 13:33:30

  Uptime 0 days 13 hours 59 minutes 59 seconds

  Draw level off

  Security ON: OS Local Authentication

  SNMP OFF

  Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file

  The listener log file /U01/app/Oracle/diag/tnslsnr/rac31/listener/alert/log.XML

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = LISTENER)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=192.168.1.101) (PORT = 1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=192.168.1.111) (PORT = 1521)))

  Summary of services...

  Service '+ ASM' a 1 instance (s).

  Instance '+ ASM1' READY State, has 1 operation for this service...

  'Cars' service has 1 instance (s).

  Instance "rac1" READY State, has 1 operation for this service...

  Service 'racXDB' has 1 instance (s).

  Instance "rac1" READY State, has 1 operation for this service...

  The command completed successfully

  In my server in the Oracle_HOME/network/admin

  This is my entry in tnsnames.ora

  RAC =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP) (HOST = rac-scan)(PORT = 1521))

  (CONNECT_DATA =

  (SERVER = DEDICATED)

  (SERVICE_NAME = rac)

  )

  )

  I am able to connect with the command

  sqlplus system/password@rac

  However, when I give the same input on the client computer

  It does not work

  I am able to ping the host rac-scan successfully

  C:\Users\rgehi > ping rac-scan

  Ping rac - scan.oracle.com [192.168.1.113] with 32 bytes of data:

  Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

  Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

  Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

  Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

  Ping statistics for 192.168.1.113:

  Packets: Sent = 4, received = 4, lost = 0 (0% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 0ms, Maximum = 0ms, average = 0ms

  C:\Users\rgehi > sqlplus system/password@rac

  SQL * more: Production of the version 12.1.0.1.0 Fri Mar 21 03:40:53 2014

  Copyright (c) 1982, 2013, Oracle.  All rights reserved.

  ERROR:

  ORA-12545: Connect failed because target host or object does not exist

  I installed oracle client on my desktop

  and I made entries in the tnsnames file

  However when I connect to the database to rac with scan it works sometimes...

  not always...

  so I'm in search mode and finally, after many moons a lot and light years away, I found the following

  Here's what I did

  # - scan

  192.168.0.127 rac31 - scan.oracle.com rac31-scan

  192.168.0.128 rac31 - scan.oracle.com rac31-scan

  192.168.0.129 rac31 - scan.oracle.com rac31-scan

  I put three ip addresses in the host with the same name rac31-scan file

  then I put the same ip addresses in my windows hosts file

  Here are the entries

  192.168.0.127 rac31 - scan.oracle.comrac31-scan

  192.168.0.128 rac31 - scan.oracle.com rac31-scan

  192.168.0.129 rac31 - scan.oracle.com rac31-scan

  but in the (windows 7 pc) client tnsnames file has just one entry

  It's here

  RAC1 =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP) (HOST = rac31-scan)(PORT = 1521))

  (CONNECT_DATA =

  (SERVER = DEDICATED)

  (SERVICE_NAME = RAC)

  )

  )

  and now when I connect from the client... it connects without any problems.

  I have tried more than 10 attempts without problem

  BINGO!

• connect with the windows computer using usb after connecting to the wireless mac

  Printer HP Photosmart 7520 connected wireless to the new iMac using Fios router wireless.

  Can I connect the printer even to an old Windows computer (running XP) via USB without interfering with the connection Wireless for Mac?

  Hi Rekjek,

  On both wireless and USB is allowed. There should not be all the problems between the Mac and the PC using the same printer.

• Unable to connect to the Mac with edge 10.8.4 inspect

  I edge inspect CC installed on my computer, chrome and on my iPHone.  I am connected to inspect according to the icon in the menu bar. My phone can see my computer but cannot connect using the IP address. However, the Chrome Extension "Please start Edge inspect" and I do not see the Edge icon in the Dock.  So I think that the thing is not activate... I think I have the last CC install, but I see not a way to uninstall the app manager and the resinstall...

  BTW, I do not know how or what type of port to open or find out if access is available on the airport. I'm on a LAN. The computer is connected by ethernet to the router, the phone is connected via WiFi to the network, and I turned to NetBarrier...

  I'm glad it helped!

  Where you need performance you can get using the default weinre server, you can run locally and set up the extension edge inspect using the local server.

  Please follow this doc: http://forums.adobe.com/docs/DOC-2623

  Also, as far as I know if you have installed the stable version of Chrome it updates only the major and non-beta versions. Who will check and let you know.

• Unable to communicate with the host computer using the network University compactRIO

  Please move this topic to the appropriate section if it is not the right section. I can't locate a Council called the compactRIO. Thank you very much.

  I encounter this problem of network communication with my cRIO 9067. the linklocal or USB connection is fine but not static IP connection on the network. I contacted the it Department to assign me a static IP address for my MAC address of cRIO. In our University, they block only unknown MAC address access and the cRIO is in the whitelist. Here are the details

  cRIO attributed to IP address: 129.12.54.xxx, tried both netmask 255.255.255.0 and 255.255.0.0, no luck

  the host computer's static IP address: 129.12.50.xxx, subnet mask 255.255.255.0 (information of cmd - ipconfig)

  First question would be: they are on the same subnet? I need to make sure that even if scientists confirm that.

  Secondly, I followed https://www.ni.com/getting-started/set-up-hardware/compactrio/static-ip by using the IP address assigned, but not luck. I've noticed that I configure same address type cRIO static IPv4 using the USB connection or for local link mode, she went in DHCP mode or Local link once I unplug the USB and restart it.

  Whenever I restart MAX, connect the cRIO and my host to Ethernet jack on the wall, it shows the DHCP mode or link with assigned Local 129.12.54.xxx IP and the subnet mask 255.255.255.248. In addition, I am not able to change it in a drop-down list even after removing it and restart MAX indicated by tutorials OR.

  If you need more information, please let me know.

  Help, please!

  Jinyu

  Dear Mikko,

  I am pleased to tell you that the problem has been resolved. The cRIO works very well.

  The reason why it does not work is in first place because they are in the other subnet. For my school, my host is 12x.1x.54.130 and the IP assigned to my cRIO is 12x.1x.54.131. the subnet mask is 255.255.255.0 number marked in red must be the same for the cRIO is connected correctly.

  Kind regards

  Jinyu

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• Unable to connect with the network via iphone or ipad

  Unable to connect the Apple TV (2nd generation) with the network via Wi - Fi using the remote app!

  The remote application required the devices to be on the same network, and home sharing enabled on Apple TV. The physical remote control would be necessary for the installation if this has not been done already

• Printer on Windows 7 PC, unable to connect with the laptop with Vista

  I have a Lexmark 2600 Series printer on a Windows 7 32-bit computer.  I am not able to connect to the printer with Vista laptop for my wife.  I can share files and see the printer.  I try to connect and I get "Windows cannot connect to the printer. Impossible operation completed (error 0x000003eb). "I tried to install locally and change the path without success.  Any help would be much appreciated.

  Hi Zyfot,

  First of all, I would say that you add the printer on the vista computer and check.

  1. open Printers by clicking the Start button, clicking Control Panel, hardware and soundand then click Printers.
  2. click on Add a printer.
  3. in the Add Printer Wizard, select Add a network, wireless or Bluetooth printer.
  4. in the list of available printers, select the one you want to use, and then click Next. If your computer is connected to a network, only printers listed in Active Directory for your domain are displayed in the list.
  5. If prompted, install the printer driver on your computer. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  6. follow the steps in the wizard and then click Finish.

  Install a printer on a home network
  http://Windows.Microsoft.com/en-us/Windows-Vista/install-a-printer-on-a-home-network

  Network printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  Also, make sure that the print spooler service is running on the windows vista computer.

  A print spooler is the service that temporarily stores the disk printing hard or in memory until the printer is ready to print.
  You must be logged on as administrator to perform these steps.

  1. open Administrative Tools by clicking the Start button, then Control Panel. In the search box, type Administrative Tools, and then click Administrative Tools.
  2. double-click on Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. right click on the print spooler service, and then click Properties.
  4. under the tab general , next to Startup type, make sure that Automatic is selected.
  5. If the service is not already running, under Service status, click Startand then click OK. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to connect with the DNS server

  Recently, I went away for the weekend and came back to find that I had no internet, on all devices... So I don't know exactly how long he was out. I'm a computer and a network engineering student and I've tried everything I can think of to make it work again. Here's what I did:

  First off troubleshooting generates an error message: "failed to connect to the DNS server.

  Of course, I did reboot of the habit of my router and my devices.

  I can't connect to WiFi or direct connection via Ethernet. I tried flushing DNS via the command-line ("ipconfig/flushdns") as well as the command "netsh int ip reset", "ipconfig/release" and "ipconfig / renew." I tried to go into the settings of the network adapter and the two affecting the IPv4 and IPv6 DNS google DNS settings. I even traded my router for a new with my ISP (of Roger (Canada)). I have connected to my router through my web browser and tried to change some of the DNS settings there (everything went well). Nothing worked so I have everything set to default. I tried ping around my own network, I ping my own card NETWORK, but also the entry door, so I know that's not my PC, I have also excluded because all my devices do not work. I spoke with Rogers (my ISP) twice now and they were no help at all, they were more concerned by the flashing lights on the router as the real problem. I'll have a technician to the course to watch tomorrow, but I doubt they'll be any help at all. I wouldn't say I'm a computer genius, but I have a pretty good understanding of how things work and I can not understand what the problem is here, I can have forgotten something or forgot to mention something I tried. But if anyone has any ideas, or similar cases they decided that I would be VERY grateful for the help.

  Hello

  Thanks for posting the query on the Microsoft Community Forums. You have reached the right place. Let us work together to find the cause of this problem and try to solve.

  There could be various reasons for which you will not be able to connect to the Internet. And I'm glad to know you have try more troubleshooting steps to solve problems.

  1. which antivirus program is installed on your computer?
  2. don't you make changes to the computer before the show?

  I suggest you try the steps from the following link and see if that helps.

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-8

  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-81&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Let us know the update after trying the steps above.