Unable to pass traffic between ASA Site to Site VPN Tunnel

Hello

I have problems passing traffic between two ASA firewall. The VPN tunnel is up with a dynamic IP and static IP address. I have attached a diagram of the VPN connection. I'm not sure where the problem lies and what to check next. I think I have all the roads and in the access lists are needed.

I've also attached the ASA5505 config and the ASA5510.

This is the first time that I've set up a VPN connection any guidance would be greatly appreciated.

Thank you

Adam

Hello

Regarding your opinion of configuration Remote Site ASA that you have not added the internal networks of the Central Site VPN L2L configurations at all so the traffic does not pass through the VPN.

 access-list outside_1_cryptomap extended permit ip 10.1.1.0 255.255.255.128 10.182.226.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 10.182.226.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 10.182.0.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 192.168.170.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 192.168.172.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 140.15.0.0 255.255.*.* 

Take a look at ACL configurations above. The 'exempt' ACL is used in configurations NAT0 and tells the ASA what traffic of exempting from NAT. "outside_1_cryptomap" ACL is used to tell the traffic between the subnets should be using the L2L VPN connection.

So in short on the Remote Site ASA these ACLs should be identical. Make additions to the LIST of VPN L2L, then try again.

I would also like to point out that to ensure that the Central ASAs L2L VPN ACL Site contains the same networks. The ACL on the Central Site will, of course, its internal subnets as the source and the site LAN remote destination.

THW out of ' crypto ipsec to show his " shows you that only the SA between binding Site Central network and the Remote Site LAN was established. Others have not formed as the configuration is lacking at LEAST on the Remote Site ASA. Can also be the Central Site.

-Jouni

Tags: Cisco Security

Similar Questions

  • SBS 2008 office1 Serv2008 Office 2 need to share assets between them via a site to site VPN tunnel

    Hi all.

    I really need help on this one.

    The office 1 installer running SBS2008 Office 2 running Server 2008.

    Each firm has its own FQDN Office 1 CompanyABC 2 A_B_C of the company office.

    Each firm has its own internal IP address pool Office 1 192.168.69.xxx and office 192.168.20.xxx 2.

    Site to site VPN tunnel between 2 office routers Netgear SRX5308 1 and 2 Netgear FVS318G Office established and working.

    Each firm has its own DNS server and acts as a domain controller

    How to configure the 2 networks to see each other and be able to use assets on every network (files, printers)?

    Is it so simple that the addition of another pool internal IP for each DNS server?

    Thanks in advance for your help.

    Hello

    Your Question is beyond the scope of this community.

    I suggest that repost you your question in the Forums of SBS.

    https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver

    "Windows Small Business Server 2011 Essentials online help"

    https://msdn.Microsoft.com/en-us/library/home-client.aspx

    TechNet Server forums.

    http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

    See you soon.

  • SA520w routing through site-to-site VPN tunnels

    I have several offices that are connected using site-to-site VPN tunnels and all will use the SA520W (firmware 2.1.18). I currently have 3 routers in place, router tunnels created for the router B and c of router. I need assistance with the configuration to allow the guests to router site B get to the router site C. I have attempted to add a static route, but get a destination unreachable host trying to ping. Also, if I connect to the router site has via the Cisco VPN client, I'm not able to get resources on each site, B, or C.

    A - the site 10.10.0.0/24

    Site B - 10.0.0.0/24

    Site of the C - 10.25.0.0/24

    Any help is greatly appreciated.

    So, that's what you have configured correctly?

    RTR_A

    ||

    _____________ || ___________

    ||                                            ||

    RTR_B                                RTR_C

    Since there is no tunnel between B and C there is no way for us past that traffic through RTR_A for two reasons. The most important reason is that subnet 10.25.0.0/24 (rtr_c) is not allowed to pass through the IPSec tunnel (it's okay to IPSec?) of rtr_a ==> rtr_b. You can't just add a statement of road because your addresses are not routable which is the reason why it fails.

    Your only option is to create another tunnel between rtr_b and rtr_c. This may not be the ONLY option, but you should get what you need.

    I hope this helps.

  • Using the same set processing on several site to site VPN tunnels

    Hi all. I have a rather strange situation about site-to-site VPN tunnel.

    On the one hand, I have a PIX 501 and on the other end an ASA5505 and a tunnel set up between them.

    The problem is that on the side of the PIX, I can't establish a tunnel, but when the traffic starts on the side of the ASA the tunnel established as usual.

    I checked the configurations on both ends and keys, passwords, mirror that LCD seems OK. The only thing that comes to my attention, it's that I have the same set of transformation used for 2 different tunnel on the side of PIX.

    Can I use the same set of transformation on several tunnels or should I set a different transformation for each tunnel? Could be the source of the problem?

    Use it on PIX

    card crypto set pfs group2

    Or on ASA, use:

    card crypto set pfs Group1

  • Keep Site to Site VPN Tunnel active for monitoring

    Hi all

    I have a configured site-to-site VPN tunnel only happen when the traffic generated from the remote peer. is it possible to keep the still active tunnel once after the tunnel is established.

    My requirement is to monitor VPN to see availability, so need to ping one of the natd(8) ip on the remote end, but it will come only when the traffic generated end peer.  currently the timers of default on SA is configured

    Help, please...

    Thank you

    Mikael

    TARGET_GP group policy attributes

    VPN-idle-timeout no

  • Site to Site VPN tunnel between two ASA

    I use the Site Wizard to Site on an ASA 5520, and ASA 5505 of the ADSM. Both are using 8.4 (5). When you create configurations. You follow the wizard configurations with manual what ACL s to allow the traffic of every subnet connected to talk to each other? Or they are automatically generated in the configuration file? Have not been to school yet to understand how to create the CLI VPN tunnels and what to look for.

    Thank you

    Carlos

    Hello

    First, I would like to say that I don't personally use ASDM for the configuration.

    But you should be able to configure all the necessary elements for a connection VPN L2L base through the wizard.

    I guess that typical problems to do so could relate to the lack of configuration NAT exempt or might not choose the setting "Bypass Interface Access List" that would mean you would allow traffic from the remote site in the 'external' ACL of ASA local interface. Like all other traffic coming from behind the 'outer' interface

    If you share format CLI configurations and say what networks must be able to connect via VPN L2L then I could give the required CLI format configurations.

    -Jouni

  • ASA 5505 and ASA 5510 Site to Site VPN Tunnel cannot be established

    Hi all experts

    We are now plan to form an IPSec VPN tunnel from site to site between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failed, would you please show me how to establish? A reference guide?

    I got error syslog 713902 and 713903, how to fix?

    I got the following, when I type "sh crypto isakmp his."

    Type: user role: initiator

    Generate a new key: no State: MM_WAIT_MSG2

    Hugo

    Hello

    This State is reached when the policies of the phase 1 do not correspond to the two ends.

    Please confirm that you have the same settings of phase 1 on both sides with the following commands:

    See the isakmp crypto race

    See the race ikev1 crypto

    Also make sure that port UDP 500 and 4500 are open for communication between your device and the remote peer.

    Finally, make sure you have a route suitable for the remote VPN endpoint device.

    Hope that helps.

    Kind regards

    Dinesh Moudgil

  • Site to Site VPN tunnel is not come between 2 routers

    Dear all,

    I have 2 routers for branch which is configured for VPN site-to-site, but the tunnel does not come!

    I ran debug and I enclose herwith output for your kind review and recommendation. I also enclose here the 2 routers configs branch.

    Any idea on why the Site to site VPN is not coming?

    Kind regards

    Haitham

    You guessed it!

    Just because you have re-used the same card encryption for LAN to LAN and vpn-client traffic.

    This from the DOC CD

    No.-xauth

    (Optional) Use this keyword if the router to router IP Security (IPSec) is on the same card encryption as a virtual private network (VPN) - client - to-Cisco-IOS IPSec. This keyword prevents the router causing the peer for the information of extended authentication (Xauth) (username and password).

  • ASA SITE VPN 55XX survey?

    Hi all

    I was wondering if I have a Cisco ASA firewall and there several site to site VPN using pre-shared keys. If I want to add an another VPN Firewall. Do I have to add all the crypto ISAKMP stuff yet or what. Or I can just all ready config VPN in the firewall. I mean besides the new card Crypto, ACLs and the NAT 0 statement that other statements do I need to enter this new site to the other tunnel in the buld order? I don't want to end up ordering more than is necessary.

    No, you don't need to add new isakmp crypto policies if you already have a configured strategies match. You can also reuse the crypto ipsec transform-set political if it is the same on the other site of the LAN-to-LAN tunnel (as long as it matches at both ends).

    You're right, the only statements, you need to add would be the ACL for NAT entry 0 and new sequence card crypto (with crypto ACL, all processing and input of game peer).

    Hope that helps.

  • ASA Syslog via a VPN Tunnel

    Hi all

    I have a little problem concerning ASA and syslogs. I have a tunnel from site to site between a local ASA and ASA distance. Behind the ASA local, I have a central syslog server (which has no ASA as default gateway) which collects messages from all network devices and I want to get messages from the ASA remote as well.

    The tunnel protects traffic between local networks behind each ASA, which includes ASA inside remote interface as well. The problem is that if I specify on the SAA distance my syslog server it does not pass through the VPN tunnel. The ASA remote sees my server syslog as being 'outside' so he's using the external IP address as the source-interface for the syslog message. Which of course does not pass through the tunnel. As much as I know there is no way to configure the interface source for logging under the SAA, that you can do on a normal IOS router.

    I've found a few documents explaining this Setup on CCO, but they all imply I have extend the list for interesting traffic to access allow remote UDP/514 of the PIX traffic outside my local syslog server interface. This isn't something I want to do what I would get in routing complication in my LAN with a public IP address of the ASA remote.

    Any suggestions? I thought I could use some sort of NAT on the ASA remote so that all traffic for my local network a source the remote PIX is translated on the inside interface, which in theory should pass the package via the tunnel. I did not go so far.

    Any help is appreciated.

    Best regards

    Stefan

    You can define the interface that the ASA will use to send the newspapers "syslog_ip host record.

    Make sure you also do "access management".

    Then the SAA should source the syslogs from inside the interface, which is probably encrypted with the crypto ACL.

    I hope it helps.

    PK

  • Site to site VPN tunnel - cannot ping the second interface of the firewall peer inside2

    I have two ASA 5505 firewall each with a basic license: FWa and FWb. currently there is a VPN tunnel between them work. I added a second (inside2) interface to the firewall, FWb, but I can't ping firewall FWa, so that I can ping the inside interface of FWa.

    I can ping the FWb inside interface 192.168.20.1 from the FWa inside 172.16.1.1 interface, but I can not ping to the 10.52.100.10 of the FWa FWb inside2 interface. I can not ping the gateway host FWa 10.52.100.1.

    I show the essential configuration of two firewalls as well as the debug icmp output on the two firewalls that I ping the internal interfaces and of FWa FWb inside2.
    =========================================================

    Here is a skeleton of the FWa configuration:

    name 172.16.1.0 network-inside
    name 192.168.20.0 HprCnc Thesys
    name 10.52.100.0 ring52-network
    name 10.53.100.0 ring53-network
    name S.S.S.S outside-interface

    interface Vlan1
    nameif inside
    security-level 100
    IP 172.16.1.1 255.255.255.0
    !
    interface Vlan2
    Description Connection to 777 VLAN to work around static Comast external Modem and IP address.
    nameif outside
    security-level 0
    outside interface IP address 255.255.255.240

    the DM_INLINE_NETWORK_5 object-group network
    network-object HprCnc Thesys 255.255.255.0
    ring52-network 255.255.255.0 network-object
    ring53-network 255.255.255.0 network-object

    the DM_INLINE_NETWORK_3 object-group network
    ring52-network 255.255.255.0 network-object
    network-object HprCnc Thesys 255.255.255.0
    ring53-network 255.255.255.0 network-object

    outside-interface of the access-list extended permitted Outside_5_cryptomap ip host object-group DM_INLINE_NETWORK_3
    inside_nat_outbound list extended access allowed inside-network ip, 255.255.255.0 DM_INLINE_NETWORK_5 object-group
    permit access list extended ip host 173.162.149.72 Outside_nat0_outbound aus_asx_uat 255.255.255.0

    NAT (inside) 0 access-list sheep
    NAT (inside) 101-list of access inside_nat_outbound
    NAT (inside) 101 0.0.0.0 0.0.0.0
    NAT (outside) 0-list of access Outside_nat0_outbound

    card crypto VPN 5 corresponds to the address Outside_5_cryptomap
    card crypto VPN 5 set pfs Group1
    VPN 5 set peer D.D.D.D crypto card
    VPN 5 value transform-set VPN crypto card
    tunnel-group D.D.D.D type ipsec-l2l
    IPSec-attributes tunnel-Group D.D.D.D
    pre-shared key *.

    =========================================================

    FWb:

    name 10.52.100.0 ring52-network
    name 10.53.100.0 ring53-network
    name 10.51.100.0 ring51-network
    name 10.54.100.0 ring54-network

    interface Vlan1
    nameif inside
    security-level 100
    address 192.168.20.1 255.255.255.0
    !
    interface Vlan2
    nameif outside
    security-level 0
    address IP D.D.D.D 255.255.255.240
    !
    interface Vlan52
    prior to interface Vlan1
    nameif inside2
    security-level 100
    IP 10.52.100.10 255.255.255.0

    the DM_INLINE_NETWORK_3 object-group network
    ring52-network 255.255.255.0 network-object
    ring53-network 255.255.255.0 network-object

    the DM_INLINE_NETWORK_2 object-group network
    ring52-network 255.255.255.0 network-object
    object-network 192.168.20.0 255.255.255.0
    ring53-network 255.255.255.0 network-object

    inside_nat0_outbound to access extended list ip 192.168.20.0 allow 255.255.255.0 host S.S.S.S
    inside2_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_3 S.S.S.S ip host

    outside_1_cryptomap list extended access allowed object-group DM_INLINE_NETWORK_2 S.S.S.S ip host

    NAT (inside) 0-list of access inside_nat0_outbound
    NAT (inside) 1 0.0.0.0 0.0.0.0
    inside2_nat0_outbound (inside2) NAT 0 access list
    NAT (inside2) 1 0.0.0.0 0.0.0.0

    Route inside2 network ring51 255.255.255.0 10.52.100.1 1
    Route inside2 network ring53 255.255.255.0 10.52.100.1 1
    Route inside2 network ring54 255.255.255.0 10.52.100.1 1

    card crypto outside_map 1 match address outside_1_cryptomap
    card crypto outside_map 1 set pfs Group1
    outside_map game 1 card crypto peer S.S.S.S
    card crypto outside_map 1 set of transformation-ESP-3DES-SHA
    outside_map interface card crypto outside

    tunnel-group S.S.S.S type ipsec-l2l
    IPSec-attributes tunnel-group S.S.S.S
    pre-shared key *.

    =========================================================================
    I'm Tournai on icmp trace debugging on both firewalls and could see the traffic arriving at the inside2 interface, but never return to FWa.

    Ping Successul FWa inside the interface on FWb

    FWa # ping 192.168.20.1
    Type to abort escape sequence.
    Send 5, echoes ICMP 100 bytes to 192.168.20.1, time-out is 2 seconds:
    Echo request ICMP from outside-interface to 192.168.20.1 ID = 32068 seq = 23510 len = 72
    ! ICMP echo reply to 192.168.20.1 in outside-interface ID = 32068 seq = 23510 len = 72
    ....

    FWb #.
    Echo ICMP of S.S.S.S to 192.168.20.1 ID request = 32068 seq = 23510 len = 72
    ICMP echo reply 192.168.20.1 S.S.S.S ID = 32068 seq = 23510 len = 72
    ==============================================================================
    Successful ping of Fwa on a host connected to the inside interface on FWb

    FWa # ping 192.168.20.15
    Type to abort escape sequence.
    Send 5, echoes ICMP 100 bytes to 192.168.20.15, wait time is 2 seconds:
    Echo request ICMP from outside-interface to 192.168.20.15 ID = seq 50862 = 18608 len = 72
    ! ICMP echo reply to 192.168.20.15 in outside-interface ID = seq 50862 = 18608 len = 72
    ...

    FWb #.
    Inside outside:S.S.S.S ICMP echo request: 192.168.20.15 ID = seq 50862 = 18608 len = 72
    ICMP echo reply to Interior: 192.168.20.15 outside:S.S.S.S ID = seq 50862 = 18608 len = 72

    ===========================
    Unsuccessful ping of FWa to inside2 on FWb interface

    FWa # ping 10.52.100.10
    Send 5, echoes ICMP 100 bytes to 10.52.100.10, wait time is 2 seconds:
    Echo request ICMP from outside-interface to 10.52.100.10 ID = 19752 seq = 63173 len = 72
    ? Echo request ICMP from outside-interface to 10.52.100.10 ID = 19752 seq = 63173 len = 72
    ...

    FWb #.
    10.52.100.10 ID of S.S.S.S ICMP echo request = 19752 seq = 63173 len = 72
    10.52.100.10 ID of S.S.S.S ICMP echo request = 19752 seq = 63173 len = 72
    ....

    ==================================================================================

    Unsuccessful ping of Fwa to a host of related UI inside2 on FWb

    FWa # ping 10.52.100.1
    Type to abort escape sequence.
    Send 5, echoes ICMP 100 bytes to 10.52.100.1, wait time is 2 seconds:
    Echo request ICMP from outside-interface to 10.52.100.1 ID = 11842 seq = 15799 len = 72

    FWb #.
    Echo request ICMP outside:S.S.S.S to inside2:10.52.100.1 ID = 11842 seq = 15799 len = 72
    Echo request ICMP outside:S.S.S.S to inside2:10.52.100.1 ID = 11842 seq = 15799 len = 72

    =======================

    Thank you

    Hi odelaporte2,

    Is very probably the "access management" command is not applied in the second inside, only inside primary (see the race management) which will confirm.

    This command can be applied to an interface at a time, for example, if the law is now applied to the inside, it can not be applied to the inside2 at the same time.

    It may be useful

    -Randy-

  • disconnecting from site-to-site vpn tunnel

    Dear Cisco

    I use the Cisco ASA 5505 5 builed VPN site to site.

    B, C, D, E of the site all site-to-site VPN A with only IPSEC IKEv2 configurartion site.

    Reading the Site an ASDM.  Monitoring VPN can always read all four sites are connected.  But I found that Site D and E during connection reset periodically with a few hours.

    (1) I would like to know the connection during the reset time is normal or not?

    (2) any installation or configuration can refine the site to site VPN.  Make VPN tunnel more stable?

    (3) any menthod can monitor VPN site-to-site is health or not?

    Thank you very much for your help

    Alan.

    A. in general, the time is set to 86400 for expiration. It can also be defined by the amount of traffic

    (B) Yes. Try turning on KeepAlive IKE

    C. check the logs is as far as I know of

    This is a good doc on VPN

    http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml

  • How to pass the traffic of a site VPN S2S by ASA to another S2S VPN site?

    I have a need for hosts on separate VPN networks connected to my ASA corp to communicate among themselves.  Example: Host A site 1 a need to communicate with host B on the site 2.  Both sites 1 & 2 are connected via the VPN S2S.  I would get every site traffic to flow through the ASA at the other site.  Where should I start my configuration?  NAT? ACL?

    I can ping each host in the network Corp. but cannot ping from one site to the other.  I set up same-security-traffic permit intra-interface and addition of NAT and rules the ACL to allow/permit 1 Site to contact Site 2.  When I do a trace of package through Deputy Ministers DEPUTIES, packets are allowed to pass. I read different that tell no NAT y at - it something at the other end of the VPN to do?  should NAT and ACLs rules be mirrored? Just in case, a site is an instance of MS Azure VM and the other is a 3rd party VM instance.

    On the HubASA, can I set up a new card encryption that selects the Site1 Site2 traffic and protect the traffic and value her counterpart Site2 public IP or just add this selection of traffic to the existing encryption card for the existing tunnel between HubASA and Site2?

    Just add this traffic to the existing encryption card.

    Remember that this should be added on three routers (two hubs and there has been talk).

    Site1

    CRYPTO ip access list allow Site2 subnet >

    CRYPTO ip access list allow subnet training3 >

    CRYPTO ip access list allow subnet HUB >

    Site2

    CRYPTO ip access list allow Site1 subnet >

    CRYPTO ip access list allow subnet training3 >

    CRYPTO ip access list allow subnet HUB >

    Training3

    CRYPTO ip access list allow Site1 subnet >

    CRYPTO ip access list allow Site2 subnet >

    CRYPTO ip access list allow subnet HUB >

    HUB

    CRYPTO_1 ip access list allow Site1 subnet >

    CRYPTO_1 ip access list allow Site1 subnet >

    CRYPTO_1 ip access list allow Site1 subnet >

    CRYPTO_2 ip access list allow Site2 subnet >

    CRYPTO_2 ip access list allow Site2 subnet >

    CRYPTO_2 ip access list allow Site2 subnet >

    CRYPTO_3 ip access list allow subnet training3 >

    CRYPTO_3 ip access list allow subnet training3 >

    CRYPTO_3 ip access list allow subnet training3 >

    Each of these ACLs is attributed to their respective crypto cards.  CRYPTO_1 is assigned the site1 crypto map, CRYPTO_2 is assigned to the site2 crypto card... etc.

    I hope that's clear

    In addition to this, you need to configure identity NAT / NAT provides both the HUB and the spokes of sites.

    --

    Please do not forget to select a correct answer and rate useful posts

  • Redirect a part of the vrf traffic between 2 sites over a redundant link

    Hey guys,.

    We have one customer (in the vrf) with 2 sites in different States and the execution of our soul of mpls... Our main link in our heart is affected by the degradation of service and want to route the client on our redundant link while retaining all other clients going on our primary link - is it possible?

    The customer in question has its own vrf (L3VPN) on both sites and running on mpls between sites. We would like to re - route this particular customer to take our backup path, while keeping everyone between sites through the primary. We do not use, rather LDP to build the SPLM.

    I don't think it's possible to only re - route a customer, but I thought I would ask the question.

    We cannot failover to secondary link for everyone between sites because the link doesn't have the capability.

    Thanks in advance.

    Hello

    Using MPLS YOU would certainly be an option. You must configure MPLS TE LS during the backup. You must also set up a separate look-back on each PE interface and use this address of the loopback interface as the next hop for the specific VRF

    IP vrf X

    BGP jump next loopback 999

    Route IP 255.255.255.255 Tu1

    In this way make you sure that only the traffic for this specific VRF would be above the tunnel of TE.

    Concerning

  • Easy traffic between remote sites via Cisco VPN

    We have a Cisco 2921 router at Headquarters (Easy VPN Server) and deployed Cisco 887VA (EasyVPN - Extension of remote network) for remote offices using EasyVPN. We allow voice traffic and data via VPN.  Everything has been great to work until this problem has been discovered today:

    When a remote user behind Cisco 887VA calls another remote user also behind Cisco 887VA, the call connects and Avaya IP phone rings but no voice in both feel.

    Calls from Headquarters and external mobile/fixed are very good. Only calls between two remote sites are affected.

    There is no need for DATA connection between the remote desktop, our only concern is the voice.

    By the looks of it, I think that "hair - pinning" traffic on the interface VPN is necessary. But need some advice on the configuration. (Examples configs etc.).

    Thanks in advance.

    Thanks for your quick response.

    I am sorry, I assumed that the clients have been configured in client mode.

    No need to remove the SDM_POOL_1, given that customers already have configured NEM.

    But add:

    Configuration group customer isakmp crypto CliniEasyVPN

    network extension mode

    You are able to ping to talked to the other?

    Please make this change:

    105 extended IP access list

    Licensing ip 192.168.0.0 0.0.0.255 192.168.0.0 0.0.0.255

    * Of course free to do trafficking of translated on the shelves.

    Let me know if you have any questions.

    Thank you.

    Portu.

Maybe you are looking for

  • Should I reinstall OS

    My 13-inch Macbook Air mid-2011 is to have a nervous breakdown. Could not connect and determined that it was because the keyboard is stuck on all caps. Use an external keyboard to open a session. Screen acting goofy, Safari crashes sometimes, still s

  • Overcharge the battery?

    If I overload my mac, the battery will decrease? I bought my mac in the summer 2015.

  • Satellite M60 question - does not detect router BTvoyager2100

    Hello I have the Satellite M60 I bought in france. The problem I encounter is that it is picking up every local router broadband (4 of them to date) with the exception of my BTvoyager2100 router. I have a portable ibm English who picks up and uses th

  • Upgrade the video card and PSU

    Hello I have a HP Pavillion A6642p It contains all the Info material: http://bizsupport1.Austin.HP.com/bizsupport/TechSupport/document.jsp?objectID=c01559154&lang=en&cc=u... I was wondering if I had to update my video card, the size of a power supply

  • How can I move the toolbar back to the bottom of the screen

    original title: my bar of windows startup has always been at the bottom of the screen.  Suddenly he moved to the right of the screen.  How can I return it the n My bar of windows startup has always been at the bottom of the screen.  Suddenly he moved