Unable to ping the remote host IP address

Similar Questions

• Unable to access the remote host

  Here is the configuration of pix of my client, the problem, here is... whenever it uses a Cisco VPN dialier, it can connect to the VPN, but cannot access any host on the distance, but with the same vpn Dialer & VPN pcf file, when it is used with a connection high speed which is not route with this PIX (or not behind the PIX) It works very well. Yet one thing I noticed, it's only when I give a static NAT, it is able to access on the remote & not through a NAT GLOBAL PC when the PC is behind the PIX.

  6.3 (3) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  Auto interface ethernet2

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  nameif dmz security50 ethernet2

  enable encrypted password xxx

  enable encrypted password xxx

  TA.qizy4R//ChqQH encrypted passwd

  fixup protocol dns-maximum length 1024

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol pptp 1723

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  No fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  No fixup not protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  access ip-list 110 permit a whole

  access-list 120 allow icmp a whole

  access-list 120 allow esp a whole

  logging console warnings

  Monitor logging warnings

  logging buffered stored notifications

  recording of debug trap

  the logging queue 0

  Outside 1500 MTU

  Within 1500 MTU

  MTU 1500 dmz

  IP address outside x.x.x.x 255.255.255.240

  IP address inside 192.168.0.1 255.255.0.0

  no ip address address dmz

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool homeuser_vpn 192.168.1.1 - 192.168.1.254

  location of PDM 192.168.0.80 255.255.255.255 inside

  location of PDM 192.168.0.207 255.255.255.255 inside

  location of PDM 0.0.0.0 0.0.0.0 outdoors

  forest warnings of PDM 100

  history of PDM activate

  ARP timeout 14400

  Global 1 x.x.x.66 (outside)

  NAT (inside) 0-list of access 123nonat

  NAT (inside) 1 192.168.0.0 255.255.0.0 0 0

  public static x.x.x.70 (Interior, exterior) 192.168.3.1 netmask 255.255.255.255 0 0

  public static x.x.x.76 (Interior, exterior) 192.168.3.2 netmask 255.255.255.255 0 0

  static (inside, outside) x.x.x.77 192.168.3.3 netmask 255.255.255.255 0 0

  Access-group 120 in external interface

  Access-group 110 in the interface inside

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  source of x.x.x.x server NTP outside prefer

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 192.168.0.207 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet 192.168.0.197 255.255.255.255 inside

  Telnet 192.168.0.80 255.255.255.255 inside

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 192.168.0.0 255.255.0.0 inside

  SSH timeout 60

  Console timeout 0

  dhcpd lease 3600

  dhcpd ping_timeout 750

  username admin password encrypted xxxx privilege 15

  username password encrypted xxx privilege 2 admin1

  Terminal width 80

  Cryptochecksum:xxx

  : end

  # 123

  Anand,

  I would check to make sure that the N - NAT has something like: -.

  "permit access ip 192.168.0.0 list 123nonat 255.255.255.0 192.168.1.0 255.255.255.0.

  And enable NAT - T - she might be his house do not understand/IPSEC passthrough device support:--

  "isakmp nat-traversal 20.

  And add: -.

  "access-list 120 permit udp any any eq 4500.

  HTH.

• Unable to ping the remote machine's scan-vip

  After following the tutorials of racattack, I did managed to install a 11.2.0.0 job cluster using clients OEL 5 virtual vmware server runing on a windows host.
  
  A question that I have connects to the vip of a remote connection analysis (11.2 windows - desktop client installed windows host)
  
  Content of the file hosts on the computer "remote" is the following:
  c:\WINDOWS\system32\drivers\etc\hosts >
  
  --------------------------------------------------------------------
  192.168.78.250 Al - scan.vm.ardentperf.com Al-scan
  192.168.78.61 collabn1 - vip.vm.ardentperf.com collabn1-vip
  192.168.78.62 collabn2 - vip.vm.ardentperf.com collabn2-vip
  192.168.78.51 collabn1.vm.ardentperf.com collabn1
  192.168.78.52 collabn2.vm.ardentperf.com collabn2
  --------------------------------------------------------------------
  
  
  I'm not able to ping scan remotley vip wherever I can ping each node vip remote MCM successfully, however I AM able to ping scan-vip rates from each node in the cluster.
  
  IM puzzled
  
  Please see below...
  
  =====================================================================
  Remote connections-
  =====================================================================
  
  
  C:\instantclient_11_2 > ping collabn1-vip
  
  Ping collabn1 - vip.vm.ardentperf.com [192.168.78.61] with 32 bytes of data:
  Reply from 192.168.78.61: bytes = 32 time < 1 ms TTL = 64
  Reply from 192.168.78.61: bytes = 32 time < 1 ms TTL = 64
  
  Ping statistics for 192.168.78.61:
  Packets: Sent = 2, received = 2, lost = 0 (0% loss),
  Time approximate round trip in milli-seconds:
  Minimum = 0ms, Maximum = 0ms, average = 0ms
  CTRL + C
  ^ C
  C:\instantclient_11_2 > ping collabn2-vip
  
  Ping collabn2 - vip.vm.ardentperf.com [192.168.78.62] with 32 bytes of data:
  Reply from 192.168.78.62: bytes = 32 time < 1 ms TTL = 64
  Reply from 192.168.78.62: bytes = 32 time < 1 ms TTL = 64
  
  Ping statistics for 192.168.78.62:
  Packets: Sent = 2, received = 2, lost = 0 (0% loss),
  Time approximate round trip in milli-seconds:
  Minimum = 0ms, Maximum = 0ms, average = 0ms
  CTRL + C
  ^ C
  C:\instantclient_11_2 > ping collabn1
  
  Ping collabn1.vm.ardentperf.com [192.168.78.51] with 32 bytes of data:
  Reply from 192.168.78.51: bytes = 32 time < 1 ms TTL = 64
  Reply from 192.168.78.51: bytes = 32 time < 1 ms TTL = 64
  
  Ping statistics for 192.168.78.51:
  Packets: Sent = 2, received = 2, lost = 0 (0% loss),
  Time approximate round trip in milli-seconds:
  Minimum = 0ms, Maximum = 0ms, average = 0ms
  CTRL + C
  ^ C
  C:\instantclient_11_2 > ping collabn2
  
  Ping collabn2.vm.ardentperf.com [192.168.78.52] with 32 bytes of data:
  Reply from 192.168.78.52: bytes = 32 time < 1 ms TTL = 64
  Reply from 192.168.78.52: bytes = 32 time < 1 ms TTL = 64
  
  Ping statistics for 192.168.78.52:
  Packets: Sent = 2, received = 2, lost = 0 (0% loss),
  Time approximate round trip in milli-seconds:
  Minimum = 0ms, Maximum = 0ms, average = 0ms
  CTRL + C
  ^ C
  C:\instantclient_11_2 > ping collab-scan
  
  Ping collab - scan.vm.ardentperf.com [92.168.78.250] with 32 bytes of data:
  Request timed out.
  Request timed out.
  Request timed out.
  
  Ping statistics for 92.168.78.250:
  Packets: Sent = 3, received = 0, lost = 3 (100% loss),
  CTRL + C
  ^ C
  C:\instantclient_11_2 >
  
  
  =====================================================================
  1 cluster node.
  =====================================================================
  
  collabn1: / home/oracle [+ ASM1] $ ping collab-scan
  PING collab-scan (192.168.78.250) 56 (84) bytes of data.
  64 bytes of collab-scan (192.168.78.250): icmp_seq = 1 ttl = 64 time = 0.036 ms
  64 bytes of collab-scan (192.168.78.250): icmp_seq = 2 ttl = 64 time = 0.030 ms
  
  collab-statistical analysis of ping-
  2 packets transmitted, 2 received, 0% packet loss, time 1000ms
  RTT min/avg/max/leg = 0.030/0.033/0.036/0.003 ms
  
  =====================================================================
  2 node cluster.
  =====================================================================
  
  collabn2: / home/oracle [RAC2] $ ping collab-scan
  PING collab-scan (192.168.78.250) 56 (84) bytes of data.
  64 bytes of collab-scan (192.168.78.250): icmp_seq = 1 ttl = 64 time = 0,489 ms
  64 bytes of collab-scan (192.168.78.250): icmp_seq = 2 ttl = 64 time = 0,238 ms
  
  collab-statistical analysis of ping-
  2 packets transmitted, 2 received, 0% packet loss, time 1001ms
  RTT min/avg/max/leg = 0.238/0.363/0.489/0.126 ms
  
  -------------------------------------------------------------------------
  
  Does anyone have any ideas why I can't ping scan-vip remotley?
  
  Any help would be appreciated (let me know any other necessary information)
  
  Thank you

  Your hosts on the client file is wrong, look at this:

  C:\instantclient_11_2>ping collab-scan
  
  Pinging collab-scan.vm.ardentperf.com [92.168.78.250] with 32 bytes of data:
  

• Diagnostics network ping to the remote host, but has not received a response

  I'm trying to figure out if there is a problem with just my laptop not wanting to connect to a local free WiFi, so any help is appreciated. He worked two days ago only to stop abruptly last night.

  Windows Network Diagnostics comes back with the error message "Can not contact www.microsoft.com (65.55.12.249)" and "diagnostic network ping to the remote host, but has not received a response.

  The only repair option it evokes is ' reset NIC 'wireless network connection ' '.

  I can always connect to WiFi using my iPhone, and even a connected laptop computer work Companion. Yet once, if this can be fixed on my end, any help would be appreciated.

  Hello BrenJones,

  Thanks for posting back. DNS servers are controlled by your ISP. I communicate with your Internet service provider and confirm that you have the good DNS for your network.

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Unable to connect to the MKS: the certificate of the remote host has these problems:

  Hello

  We have a host of ESXi 4 cluster running any vSphere 4.1.  Recently, I started to upgrade to update 2 and all the additional fixes.  After the upgrade of the vCentre server to the latest version (or maybe before I can't noticed) an of are hosts began to show the following error whenever I tried to connect to the console of any guest on this host.

  Unable to connect to the MKS: the certificate of the remote host has these problems:

  It lists any problems at all and no error display in the event log that it simply does not work.  I had a prod around the internet and found nothing.  I then rebuilt the host to exclude and the problem remains.

  Any help would be much appreciated.

  Thanks in advance

  David

  If you can connect to the Console remotely using VMware Infrastructure (VI) Client connected directly to the host, take a look at vmware KB to connect to a remote virtual machine fails with the error: the certificate of the remote host has these problems

  but more generally - remove host to vCenter inventory and then add the host to the back, take a look at opening in the console of the virtual machine after a new installation of ESXi or ESX fails with the error: the host certificate chain is not complete and could not connect to the MKS: the certificate of the remote host has these problems

• QuickVPN - could not do a ping the remote VPN router!

  Hello

  I have a RV042 (VPN router) and I have some problems to run properly using the QuickVPN client.

  Here is the Log of the QuickVPN client.

  2008-10-15 20:14:38 [STATUS] a network interface detected with 192.168.0.104 IP address
  2008-10-15 20:14:38 [STATUS] connection...
  2008-10-15 20:14:38 [STATUS] connection to a remote gateway with IP address: 96.20.174.84
  2008-10-15 20:14:38 [WARNING] server certificate does not exist on your local computer.
  2008-10-15 20:14:44 remote gateway [STATE] has been reached with https...
  2008-10-15 20:14:44 [STATUS] commissioning...
  2008-10-15 20:14:51 [STATUS] Tunnel is connected successfully.
  2008-10-15 20:14:51 [STATUS] verification of network...
  2008-10-15 20:14:55 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:14:58 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:01 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:05 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:08 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:11 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
  2008-10-15 20:15:19 [STATUS] disconnection...
  2008-10-15 20:15:25 [STATUS] Tunnel is disconnected successfully.

  I don't know how it is implemented, but if WuickVPN wait a form ping my router, it will not happen. I was never able to ping my router ouside of my ISP network.

  There is a way to disable the Ping process and continue with the VPN connection?

  QuickVPN try ping on the router via the VPN tunnel to check the connection. It should work without worrying about whether your ISP filters ICMP messages or not. The tunnel is encrypted your ISP won't know what you're doing.

  Please post the corresponding on the RV042 VPN log. That is expected to see how far you get.

  You have a firewall running on the computer? I think that some firewalls have difficulty with the traffic of ESP.

  What is the router that is connected to the computer? How is it that is configured?

• Existing connection had to be closed by the remote host

  Need help with this error
  I have a dev and a uat environment.
  I have a small form that I use as a method to call a web service. Essentially, the form contains a web service URL text box.
  If I call the shape on the dev and pointer to the service web dev, it works.
  If I use the form on uat and point the service web uat it works.
  If I use the form on UAT and call the web service on dev, it works.
  However, if I use the form on the dev and point the web service uat I get this error:

  In the Application Server error ' / '. An existing connection was to be closed by the remote host Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and its origin in the code.

  Exception details: System.Net.Sockets.SocketException: An existing connection was to be closed by the remote host

  Source error:

  The source code that generated this unhandled exception can only be shown when compiled in debug mode. To do this, follow one of the below steps, then request the URL: 1. Add a "Debug = true" directive at the top of the file that generated the error. Example: <%@ Page Language="C#" Debug="true" %> or: (2) add the following section to the configuration file of your application:                 Note that this second technique, all the files in an application to be compiled in debug mode. The first technique will make only this file to be compiled in debug mode. Important: Running applications in debug mode causes a memory/performance load. You must ensure that an application has debugging disabled before deploying to the production scenario.

  Stack trace:

  [(0 x 2746) SocketException: an existing connection was to be closed by the remote host] System.Net.Sockets.Socket.Receive (Byte [] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) + 73 System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) 131 [IOException: unable to read data from the transport connection: an existing connection was to be closed by the remote host.] System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 294 System.Net.PooledStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 26 System.Net.Connection.SyncRead (request of HttpWebRequest, Boolean userRetrievedStream, Boolean probeRead) + 297 [WebException: the underlying connection was closed: an unexpected error occurred during the reception.] System.Net.HttpWebRequest.GetResponse () + 5399741 _Default.btnTestUpload_Click (Object sender, EventArgs e) + 532 System.Web.UI.WebControls.Button.OnClick (EventArgs e) 111 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) + 110 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent (String eventArgument) + 10 System.Web.UI.Page.RaisePostBackEvent (IPostBackEventHandler sourceControl, String eventArgument) + 13 System.Web.UI.Page.RaisePostBackEvent (NameValueCollection postData) + 36 System.Web.UI.Page.ProcessRequestMain (includeStagesBeforeAsyncPoint, Boolean, Boolean includeStagesAfterAsyncPoint) 1565

  Version information: Microsoft .NET Framework Version: 2.0.50727.4234; ASP.NET Version: 2.0.50727.4223

  Any ideas?

  Hello

  I suggest you for this post in the appropriate section of the form of MSDN

  http://social.msdn.Microsoft.com/forums/en-us/categories/

  I hope this helps.

• On the remote host MySQL database: password encryption?

  Hello

  I discovered the world of PHP and MySQL in the last days. I didn't get all the intricacies still but nevertheless I managed to set up a server "localhost" on my computer, create a MySQL database and display correctly information in this database in HTML using PHP pages.

  I am now at the stage of transferring it to the remote host where the site will happen: I exported my database, imported these information in the database on the server host and I n unexpectedily even just to get my PHP/HTML pages to connect to this database. It's great.

  I have one question. I've read a lot of thread in this forum about this, but haven't seen an answer: must the password encryption? I mean, when I connect to a database using DW CS4, the software creates for me a connections folder in my Web site root folder and stores inside a little PHP to the folder with the server name, database name, user name and password which are necessary to allow PHP to connect to the MySQL database. It is all printed clearly in there. Once which is transferred to the remote host, it is always accessible to anyone? Should I not worry and try to hide the password?

  Any thoughts on this would be greatly appreciated.

  Emilie

  Thread moved to Dreamweaver application development forum, which addresses other issues aside and PHP/MySQL server.

  As long as the server is enabled in PHP, put the connection details in a PHP file like this is not a problem. PHP code is processed on the server. Only its output is sent to the browser. Even if someone guesses the name of your connection file, they won't see anything if they try to load the page in a browser. The only way they can see it is to hack into the server. It is important to have passwords on your FTP account.

• An existing connection to be closed by the remote host.

  Since last week, I can't keep a connection to the server of vatsim or acars for virtual pilots micro flight simulator will for more than five minutes. the error message is that an existing connection had to be closed by the remote host

  not an expert of anymeans and all the answers I got on the net are well above my paygrade.

  Hi dva8377,

  Here are two additional methods you can try.

  1: Restart the computer by using a clean boot of the method

   

  When you start Microsoft Windows, other software may start with the operating system. These programs may include antivirus software and system programs that may interfere with the game. When you perform a clean restart procedure, you prevent these programs from starting automatically.

  Reference:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Method 2: Bypass the router

   

  If you connect to the Internet using a router, there may be a problem with the configuration settings, which requires that the updated settings. To determine if a network connectivity problem is caused by a bad configuration or a problem affecting the router, try bypassing the router by connecting your computer directly to the modem. Remember that this test will only check that the router is configured correctly. If the game connects to the Internet without problem when you bypass the router, plug the router immediately and contact the manufacturer of the router or your ISP for help configure the router correctly.

  Note: Ensure that you switch your computer to normal startup mode after completing the troubleshooting steps. Steps are available in the article above.

  For more information, see: http://www.microsoft.com/Products/Games/FSInsider/tips/Pages/default.aspx

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Whenever I try to download I get this error message "a socket operation was attempted to an unreachable network. "This means that the local software knows no route to reach the remote host.

  Hi all

  I use windows 7. whenever I try to download I get this error message "a socket operation was attempted to an unreachable network. "This means generally that the local software knows no route to reach the remote host" what does that mean?  help solve this problem. Thank you '.
   
  Original title: proxy error

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/categories

  Hope this information is useful.

• Unable to display the remote folder: the remote folder F:/wamp/www / "MYWEBSITENAME" / is not accessible or does not exist.

  In CS4, all of a sudden, I get the error "unable to display the remote folder: the remote folder F:/wamp/www /"MYWEBSITENAME"/ is not accessible or does not exist.»

  I'm in Manage Sites and test the file in the remote folder and it says "Dreamweaver connected to your web service successfully.

  I have not changed anything.  I had this once before a few years ago and just copied on the site of a new name and that fixed it, but it does not for the moment.

  Help.   Any ideas?  Thank you

  When you click the expand button in your files window, whose icon is selected in the upper part?

  

  The middle one is the test server (list of lightning bolt), if you try to download, you will need to switch to the remote server (standard search bullet list icon).

  If you do not have a local server running on a drive of F, and you try to put it on the test server, you will get an error saying: there is no. Is it happening?

  If you do not have a local server running on your F drive, remove the test server info, it is not necessary.

• Copy Clone VM on the remote host?

  We currently have a Vcenter configuration limited to 3 guests.  I am creating a system for disaster, assuming that our main centre of recovery should fail.

  So, I need to program a clone of the VM are held every week - but then I need to copy this clone to a remote host which is not in the same data center, although it IS on the same network.

  Is there a way to achieve side manually remove a host to Vcenter and adding remote host (4th) whenever I want to copy?

  If I copy the clone on an external drive, I have to copy it again to the remote host.  It is 2 instances of copy on the network and which can last for hours.

  I want to reduce it to a single copy and perhaps even automate it with a script, but I don't know everything that the CLI in ESXi.

  Any ideas are appreciated.

  Understandable, I thought you wanted to just copy of VMDK but a clone first takes a snapshot of the virtual machine. This removes the lock on the base VMDK. ESXi can run rsync, but it is not supported. It is perhaps a bit over your head because you have no experience with Linux.

  http://www.virtuallyghetto.com/2011/02/how-to-compile-statically-linked-rsync.html

  What you could do is however if sure the source host and destination have access to the same storage. Then plan a clone to the virtual machine, but leave it turned off permanently. In the case of DR, on the other host, go to the data store, select the virtual machine folder, right-click the .vmx and say file added to the inventory. You can then restart it on another host. Or the DR host only has local storage?

• I upgraded to ESXi 5.0 to 5.5 ESxi now when I ping the esx host, it fails.

  I upgraded to ESXi 5.0 to 5.5 ESxi now when I ping the esx host, it fails.

  I was able to ping before the update. Test management system also fails to ping the default gateway.

  I sent a private message you, could answer you on this one here? Got iso's, he's now testing in my lab, but I don't have that kind of network cards, you will need to do the real test for me.

• Error during communication with the remote host when you create the new virtual machine

  I'm under 7 ESX servers on IBM Blade H22 there is a mistake to invite while I create a new virtual machine

  on the vcenter Server

  At the end of 30-35 minutes, it gives an error

  "Error during communication with the remote host"

  The existing machines are working well... I tried to create virtual machines to other ESX servers as well

  but the same question. I also tried to make the clone of existing machines, but without success

  Can anyone help?

  You rescan the LUNS once?

  You've restarted the management agent?

  You've restarted the vpxa?

  If this isn't the case, please perform the step above and check out them.

• CS4 'the connection to the remote host was lost.

  Suddenly, I get the error message (CS4) when I try to connect to remote hosts: "the connection to the remote host has been lost. Click Refresh to reconnect. "It is impossible to connect to a remote host.

  This happens for all my sites on remote servers in different countries, so it must be a problem of DW. Please advice.

  Have you tried to use passive mode:

  Definition of site > advanced > click on the passive FTP box and see if it works.

  --

  Nadia

  Adobe Community Expert: Dreamweaver

  ---------------------------------------------------------------

  Unique templates CSS | Tutorials | SEO articles

  http://www.DreamweaverResources.com

  --------------------------------------------------------------------------

  Web Design & development

  http://www.perrelink.com.au

  http://Twitter.com/nadiap