Unable to start the system in xp sp3 after you download windows updates

Similar Questions

• I get the error code 80070005 when you download Windows updates

  Original title : I use Windows 7, Vista Home Premium on a laptop. I can't download updates and get the error code 80070005

  When you try to update, I get the error code 80070005. System: 64-bit, service pack 2, M-6880 of Gateway computer memory 4.00 GB

  Hello

  1. what day you're talking about?

  2. don't you make changes to the computer before the show?

  Please follow the steps below.

  Method 1:

  Step 1: Put the computer to boot.

  Click on the link below

  http://support.Microsoft.com/kb/929135

  NOTE: after you install the update properly, restore the computer to start as usual (see step 7 link mentioned above)

  Step 2: Download and install updates from Microsoft Download Center manually.

  a. visit the Microsoft Download Web site, type the number of "KB" in the search box and press ENTER.

  b. in the list of search results, click on the (KB) Knowledge Base article link to go to the download page. If there is more than one list, look for a link that goes to the Microsoft Download Center.

  c. If there are several versions on the download page, find the appropriate for your computer. Click on the download button and save the update to your desktop.

  d. When you are prompted, click open to install the update.

  Microsoft Download Center

  http://www.Microsoft.com/download/en/default.aspx

  Method 2:

  Run the Microsoft Fixit from the link below.

  http://support.Microsoft.com/mats/windows_update/

  Method 3:

  Reset components from Windows Update from the link below.

  Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/971058

  Method 4:

  Follow the steps from the link below.

  http://support.Microsoft.com/kb/2509997

• After you download an update, I lost all the photos and graphics

  I have version 10.4.11 and run firefox as a web browser. I had to download an update of firefox. After this download, I don't see any reason or photos.

  Sorry, I forgot to change the links for Mac. On Mac, you can use Firefox > Preferences rather than Firefox/tools > Options

  • http://KB.mozillazine.org/Menu_differences
  • Windows: Firefox (Tools) > Options
  • Mac: Firefox > Preferences
  • Linux: Edit > Preferences

• Unable to start the system over 3000 N100

  Cannot use my laptop that I can't start, just the Lenovo splash screen appears indicating lenovo care press to pop the normal start up.  Nothing happens when I do that, nothing happens when I try to access the start up or alternative boot said just access please wait - I think more than half an hour is a long time to wait.

  Have tried using recovery discs, but cannot read disks, starting to do and then stops.

  Thanks a lot for your suggestions.

  Sorted.

• vCenter Server service does not start after you run Windows updates

  On a regular basis, my vCenter Server service fails to start after the automatic updates of windows are applied.  The vCenter server is a datacenter 2008R2 VM.

  The only other running applications are PerfectDisk and agents of ESET NOD32 - vCenter is in 4.1.  I tried to adjust the vCenter Server and WedAdmin service of delayed start, but that doesn't seem to make a big difference. The following errors are displayed in the case of the newspaper which lead me to think the issue is related to SQL:

  SQL Server is not ready to accept new client connections. Wait a few minutes and try again. If you have access in the error log, look for the informational message that indicates that SQL Server is ready before trying to connect again.  CUSTOMER:: 1

  The description for event ID 1000 from source VMware VirtualCenter Server can not be found. Either the component that triggers this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.

  If the event is on another computer, the display information had to be saved with the event.

  The following information has been included in the event:

  Could not initialize the VMware VirtualCenter. Closing...

  the message resource is present, but the message is not in the string/message table

  Anyone encountered this before?

  Hello.

  I didn't know this, but the info in Ko 1007669 may be useful.

  Good luck!

• Code error 8024002d when you use Windows Update to install the update of security for Director 2.6 for windows vista

  I get the error code 8024002d message when you use Windows Update to install the update of security for Director 2.6 for windows vista. It try to install then a window pops up saying: he cannot locate a file called "MM26_ENU [1] .msi '. I have serached my PC and no such file exisits. Grateful for any help. This is supposed to be an update of important safety for Movie Maker.

  Alan McC
  Do you have other accounts of users on this PC?  If you install this update from the main account?

  You should get the number of the update of the updated history list and then download the file here: Microsoft downloads.
  If sure that nothing else is running, and then install the update manually.  Give it a try and let us know the results.

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• AutorunsDisabled window opens when you start the system.

  Whenever I start my computer (Windows XP SP3), a Windows Explorer window appears showing the AutorunsDisabled folder.  Nothing is in the folder.  I installed Windows XP-KB967715 - x 86 - ENU.exe and MicrosoftFixit50471.msi of Fix - It of Microsoft in the hope of preventing the Windows Explorer window to appear whenever I start the computer.  He still appears every time on starting the system or re - start.  Can someone help me with this problem?  Thanks in advance.

  It's probably in your startup folder. Check. Start, all programs, startup. To remove the open disk (c), open Documents and Settings, open all users or the folder with your name (only in one, try all users initially), open a Start Menu, open programs, open start and if it is delete it.

• I'm unable to install the Microsoft. NET Framework 4 client for windows 7 X 64 profile base system. Any ideas?

  Original title: Microsoft. NET Framework 4 client for windows 7 X 64 profile base system

  I'm unable to install the Microsoft. NET Framework 4 client for windows 7 X 64 profile base system.

  Any ideas?

  Thank you.

  Hello

  Thanks for posting your query on the Microsoft Community.

  I understand that you have a problem with the installation of Microsoft. NET Framework 4 client profile. I will certainly help you in this matter.

  Provide us the following information to better help you.

  • Have you made changes on the computer before this problem?

  • You receive an error message/code?

  Follow the below methods:

  Method 1:

  The .NET Framework 4 Client Profile is available on Windows Update
  http://support.Microsoft.com/kb/982670

  Follow the method 1 and method 2 in the article and check for the issue. If the problem remains same follow method 2.

  Method 2:

  Disable the .net framework Windows feature on or off, follow these steps:

  a. click the Start button, select Control Panel, click programsand then click Windows turn on or off features. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  b. to turn off .net framework, click the media feature. And the .net framework and click OK.

  c. restart the computer to apply the changes.

  Note: follow the steps above to activate or activate the .net framework and check if the problem occurs.

  For more information, refer to this link turn Windows features turn on or off:

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-features-on-or-off

  Please let us know if you need more assistance.

  Thank you.

• HP stream 11-d010wm: I have a hard time to start the system it asks me the password for administrator password or power

  I have a hard time to start the system he asks me the password for administrator or power password which I don't have
  
  This is the code that I get when I entered the wrong password 3 times-(56448130) I would be grateful help
  
  Thank you!

  @dj_infiel95

  Enter 49520116

  Kind regards

  DP - K

• Satellite L450D - 13 X does not start the system - PXE - E61: Media test failure

  Hello

  I turned on my laptop after only a day and it will not load
  As a first step, he said start the system restart or start normally,

  I chose startup repair, but it does not complete the repair.
  It now comes with a repetitive screen with PXE - E63: media test failure, check cable of
  PXE - MOF: exit ROM PXE

  I tried Googling the answer and go into the BIOS menu and to the section boot but I can't seem to change anything at work.

  There are, and exclamation mark in front of what I think is my hard drive on the screen

  ! HDD1/SSD1 TOSHIBA MK2555GSX-(S2)
  CD/DVD HL - DT - ST DVDRAM GT20N-(S4)
  FLOPPY DRIVE
  LAN

  I have nothing in the disk drive and I don't have a recovery disk.

  Any help would be appreciated

  Thanx

  Leon

  Hello

  For me, it looks like a malfunction of the HARD drive and so the BIOS can not find a bootable device and goes to the last possible bootable option which is LAN.

  The exclamation mark in front of the HARD drive indicates that there is a problem with the HARD drive so I think you need to replace the HARD drive and you need to reinstall the system.

  PS: What laptop do you have exactly?

• Satellite A100-00N - cannot start the system

  There were 15 months and now when I push the power button to start the system, it will not work.

  There are 2 blue LEDs lighting but the computer won start t. tried to release the battery and configure power but not luck, with the battery also no luck. On Toshiba that works is the button located under the power button (globe photo with the left and right arrows and a photo of a music note in a display of television or something) when I press this button you hear system starts but after a second or 3-4.

  Also tried to remove the memory and hard drive but still no luck.
  Anyone?

  Sorry, but there must be a serious problem, and I don't think that there is nothing you can do. The idea to start the laptop with power running is OK, but if this doesn't work and you see nothing on the screen, it must be a serious problem.

  Of course you do not give any information that you did the last days with your laptop. Maybe you tried to update BIOS?

• Whenever I start the system complains that the following files are missing, c:\\Windows\System32\igfxpers.exe, igftray.exe and hkcmd.exe.

  Original title: files missing error

  Whenever I start the system complains that the following files are missing, c:\\Windows\System32\igfxpers.exe, igftray.exe and hkcmd.exe. Everything started after I ran scan and scan deleted some files infected. However, I can use the system. Where and how to download the missing files? Or how the system does not deliver messages?

  Simon

  Two of the three files are probably part of the malware infection and not the files infected. The third is probably the same details in this link:
  http://www.Runscanner.NET/file/Hkcmd.exe.html

  To identify what loads when you start using Autoruns (freeware from Microsoft).
  http://www.Microsoft.com/technet/sysinternals/ProcessesAndThreads/Autoruns.mspx

  With Autoruns, you can deselect an item which disables startup, or you can click with the right button on an item, then remove it. If you clear the check box that you can check back for re - activate the element. It is an approach much safer than editing the registry and better than using msconfig. You will find the three points and they will have a description 'file is missing' against everyone. Your antivirus software has removed the files, but not the startup entries in the registry. All you need to do is delete the entry using Autoruns to eliminate the error messages.

  Another useful feature of the program is that you can click with the right button on an item and select search online to get information about the selected item.

• My home edition vista is continually updates configuration and then close. I can't stop it. I want to slate and wipe the hard drive but are unable to restore the system.

  How do I do a system restore with Vista Home basic when it is stuck on configuring updates?

  Hello

  You shouldn't have a system restore to fix this.

  You can use the solutions in this KB - 3 methods and I listed a little help for them below

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista and Windows 7
  http://support.Microsoft.com/kb/949358

  Method 1: Start Windows Vista/Windows 7 with the Windows installation media and use the repair feature

  How to do a startup repair in Vista and Windows 7
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  You can also do a safe mode startup repair to access the Recovery Options If you have them available
  or use the DVD as described above.

  This tells you how to access the system - Vista Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  This tells you how to access the system - Windows 7 Recovery Options
  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Method 2: Start the system in safe mode and then use the system restore feature

  How to do a system restore in Vista and Windows 7
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can also do a restore of the system of starting with a disk of Vista or Windows 7.

  Method 3: Use the downloads at the end of this article - note for Vista x 86 versions 32 bit and Vista
  x 64 64-bit.

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista and Windows 7
  http://support.Microsoft.com/kb/949358

  ------------------------------------------------------

  Once you are in Windows I was running once again reset here as a precaution.

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Hope this helps sort it out for you.
  Rob - bicycle - Mark Twain said it is good.

• Unable to run the system restore, or any audio file...

  I am unable to run the system in normal mode or safe restore.  When I try to run rstrui.exe a pop up box appears and wants to know what program I want to run this file.  Also when I go to my control panel I can't open anything even not my add or remove channels I get an error msg saying c:\windows\system32\rundll32.exe - application not found - even when im in safe mode appears the same box... help would be appreciated... :-)

  It sounds like you lost the file association for .exe files.
  Visit the following site and follow the instructions to restore your .exe file associations.  Be sure to read the note at the top that applies specifically to the .exe file associations:

  <>http://www.dougknox.com/XP/file_assoc.htm >

  HTH,
  JW

• Cannot open any file, start the system restore or use my original XP pro CD

  original title: no CAN NOT OPEN ALL the FILES ON MY OS, I can't START the SYSTEM RESTORE, I can't EVEN USE MY XP PROFESSIONAL ORIGINAL CD... HELP PLEASE!

  I HAVE A DELL INSPIRON / B130 LAPTOP WITH XP PROFESSIONAL OPERATING SYSTEM.  I GOT HOME THE OTHER DAY TO FIND MY ROOMMATE ON MY LAPTOP, AFTER THE LECTURES OF THE PERSON TO KEEP YOUR HANDS OFF. I OPENS AND DISCOVERS WHAT HAS HAPPENED. THE PERSON DOWNLOAD FREE DOWNLOADERS VIDEO 4 X, AS WELL AS FILMS AND OTHER JUNK ON MY COMPUTER... ETC I WENT TOO ADD REMOVE PROGRAMS AND DELETED PROGRAMS THAT KEPT DUPLICATE ITSELF. I SHUT DOWN MY COMPUTER, TO THE REBOOT. NOW I GET THESE MESSAGES... "WINDOWS CANNOT OPEN THIS FILE", EXE, FILES,. INK AND WELL BASICALLY ALL THE FILES FILES. I CAN'T OPEN THE SYSTEM RESTORE, ENTER ADMINISTRATOR, I CAN'T EVEN USE MY WINDOWS XP PROFESSIONAL CD ORINGINAL, IT SAYS: ERROR. 3514 LINE, I DON'T KNOW WHAT ELSE TOO CAN YOU PLEASE HELP ME? Thank you

  Hi Colleen,

  Please take a look at the following suggestions for a possible solution:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_programs/cannot-open-any-exe-files-cant-open-any-programs/85545ac1-3822-47AA-b664-e4209c62e9be