Unable to start Vista

Similar Questions

• Unable to start Vista, perhaps in connection with the event ID 3004?

  I'm running Vista (64 bit) on a Dell Inspiron 1440 laptop. For some reason it won't finish boot normally. This just started today. The laptop is only a few months old and I have not had other problems. I don't remember installing something new.

  I can boot into safe mode (even if it is very slow and can't run all applications). I tried Startup Repair (did not find anything) and for some reason any there is no restore point (how this happens?), so I can't restore it to the previous point time.

  Running sfc/scannow returns the result "Windows Resource Protection found corrupt files but was unable to fix some of them.
  I can't understand how to get log (not that I understand it anyway but I wanted to post this information here...)

  In the case of the spectator, I found a few errors that correspond to the time I tried to start the computer without success. The news of the event are as follows:

  "Windows cannot verify the integrity of the image of the file \Device\HarddiskVolume3\Windows\Temp\mc2731C.tmp because the hash of the file is not found on the system. A recent hardware or software change might be installed a file that is signed incorrectly or damaged or maybe it's a malicious software from an unknown source. »

  Log name: Microsoft-Windows-CodeIntegrity/Operational
  Source: Code integrity
  Event ID: 3004
  Level: error
  User: SYSTEM
  OpCode: (6815744)

  Do you think this could be the source of my problem? Any idea what I can do about it?

  Thank you!

  ~ Somewhere

  Hello

  (A) check the clean boot.
  
  A clean boot helps eliminate software conflicts.
  The following link has steps showing how to perform the clean boot. http://support.Microsoft.com/kb/929135
  (1) perform the clean boot
  i. Click Start, type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  II. in the general tab, click Selective startup.
  III. under Selective startup, clear the check box load startup items.
  IV. click the Services tab, select the hide all Microsoft Services check box and then click Disable all.
  v. click OK.
  VI. When you are prompted, click on restart.
  VII. after the computer starts, check if the problem is resolved.

  (2) enable half the services
  (3) determine whether the problem returns
  (4) enable half of the startup items
  (5) determine if the problem returns
  (6) repeat the steps above until you find out which program or service is causing the issue
   
  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.
   
  Note: make sure that the computer is configured to start as usual by following step 7 of article http://support.microsoft.com/kb/929135 .
  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  (i) click Start, type msconfig.exe in the start search box and press ENTER. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  (II) on the general tab, click the Normal startup option, and then click OK.

  (B) you can also perform a virus scan in SafeMode with network online.
  (To start in SafeMode with network, keep tapping the F8 key during restart the computer and select Safe mode with network and press ENTER.)

  i. try to scan the computer using Antivirus software because this problem can occur if the computer is infected with the virus. You can do a scan of PC security by clicking on the link http://onecare.live.com/site/en-us/default.htm and clicking on the analysis of a complete Service and accept the agreement.

  II. to download malware removal (this tool checks your computer infections by specific, prevalent malicious software (including Blaster, Sasser, and Mydoom) and helps to remove the infection if it exists) tool visit the link http://www.microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Diana
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• "Support & was unable to start" Vista Home Basic which can be please

  I use Vista Home Basic with Service Pack 1 and 2 is installed. When I click on help and Support, it shows error message "Help & Support could not start" someone knows how to put this right please? Thank you.

  Hi André,.

  You can take the help of this link.

• Unable to start Vista in a dual boot with XP

  original title: a 1.5 T hard drive 3 partitions. XP to end vist Center. When it is installed vista it does not start XP.

  I had xp pro on the end of the disc hard and then installed vista professional.  At boot, it gives a selection vista or windows more old op system.  If I highlight the older windows (xp) it gives a message that it is not bootable.  Can I change the MBR to recognize and start xp or what other measures can I take?

  Hi CIIIC,.
   
  I suggest you follow this below Microsoft KB article provided and see if the problem is resolved.
   
  In a dual-boot configuration, Windows XP does not start if you then format or delete the partition on which Windows Vista is installed
  http://support.Microsoft.com/kb/922809
   
  See also:
  
  Windows no longer starts after you install an earlier version of the Windows operating system in a dual-boot configuration
  http://support.Microsoft.com/kb/919529 

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• Unable to start: Vista boot.

  I have a Dell with Vista 1526.  The machine on the powers, but does not start for Vista.  I have no disk.  How can I start to Vista?  I tried the bios and it does not work.

  original title: Vista boot.

  H. Weiner

  If you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Dell recovery options:

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  Above is Dell to reinstall Vista from the DVD on your computer.

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

  And that way if you have a recovery partition on your hard drive.

  Mick Murphy - Microsoft partner

• I tried to install windows vista on my laptop but I m unable to start because of a message error loading operating system.

  I tried to install windows vista on my laptop but I m unable to start because of a message error loading operating system. good quick response.

  Hello

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  Here's how to do a clean install of Vista:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  See you soon.

• ERROR: Unable to start Bluetooth stack service

  I seldome use features wireless to my pc before, but now that I have the wireless router I frequelty use it. Usually, I turn on the wireless switch and turned off to save the battery. I noticed every time I turn on the radio, after a few minutes, that an error message is displayed:

  BTTray

  ERROR: Unable to start Bluetooth stack service

  I don't know if what is wrong with my laptop. Please if anyone can tell me if what is wrong with this thing. Thank you very much!

  HP pavilion dv6820ee

  OS: Windows Vista editions Home premium.

  Message edited by xXxonins on 12/22/2008 05:27

  Access your product download page and reinstall the software for bluetooth under networks:

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2093 & LC = on & DLC = in & CC = US & Product = 3716846 & lang = in

  then, under network connections in the network and sharing window - see if you have a bluetooth adapter that is listed.  If you do not use bluetooth, you can turn it off or you should be able to set it up properly.

  If fails it then in Control Panel, under administrative tools, Services - locate service BTtray and disable it.

  HTH

• answer me please! Unable to start? Bluetooth stack service! that means this popup

  I got NO help from anyone Thanks much all that you brains out there cannot get a response?

  From the other thread:

  Unable to start Bluetooth stack service? What is this and how do I get rid of him. printer works well. This service is useless.

  Hello! very annoyed with a popup that I said at the top left of the BTty yellow! mark in the middle of the box and the message unable to start Bluetooth stack service, I click OK and it goes away a while tried all my settings are unable to get rid of it. It started when I let a 2nd. or 3rd. part microsoft co. take possession of my pc to difficulty clutter & defragment only HELP get me to pay 149.99 at this time, very unhappy.

  Hi Patgariepy,

  What operating system is installed on the computer?

  You get this error if the drivers are not updated, or if the driver has been corrupted. I suggest measures are:

  Method 1: Bluetooth device driver update. Steps to update the device driver:

  a. click on start
  b. Select Control Panel
  c. Select system and maintenance
  d. click Device Manager (if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.)
  e. in the Device Manager, look for the Blue tooth device
  f. click on the driver tab and then select Player update

  Link for reference: updating a hardware driver that is not working properly

  http://windowshelp.Microsoft.com/Windows/en-us/help/b3c6477e-1111-4B9F-A52A-fffdc51e9c901033.mspx

  Method 2: Uninstall the Bluetooth device, restart the computer and install the latest drivers.

  You can even check out the link below, which will set the Blue tooth device: point of Bluetooth in Control Panel on a Windows Vista SP2 does not work as expected when you click the http://support.microsoft.com/default.aspx/kb/960531elementNote: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article: back up the registry in Windows 7

  Keeps us up-to-date on the State of the question.

• Unable to start error: 0xc00000e9

  There was no change to the laptop, this error message, it is impossible for me to recover and treat my work in class, not to mention the laptop does not start. help help!

  original title: windows does not start, the error message saying hardware or software changed caused fo the Computer unable to start smoking... status: 0xc00000e9. help that I'm a student trying to finish my homework before class on Tuesday. HELP__

  Hi helpthislady,

  Sometimes, this error indicates that the hard drive may be failing.  Perform the following steps to check the integrity of your hard drive. If you are unable to access the Advanced Boot Option menu by using the F8 key, you will need to get a CD of Windows Vista.

  1. reboot your computer by tapping the F8 key until you reach the Advanced Startup Options menu.

  2. Select Safe Mode with command prompt.

  3. type chkdsk/r (there is a space between the k and /)

  Once you are able to start Windows, back up all your important data.  Let us know if that helps.

  Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• When you try to use Windows Help & Support, get a message unable to start

  I tried to search for a topic USING WINDOWS & SUPPORT... But, I got a MESSAGE saying that "Windows Help & Support ' is unable to start and for more information go to or click here to: http//.windowshelp.microsoft.com.  All of this and now I'm HERE... Is there someone or someone who can help me?  Give me some suggestions. Thank you...

  Hello

  1. about what you are looking for?

  2. what you trying to accomplish?

  3. don't you make changes to your computer?

  I suggest you follow the link and check.

  I can not open Help files that require the Windows Help program (WinHlp32.exe)

  http://support.Microsoft.com/kb/917607

  I also suggest you to follow the link and check.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

• I'm unable to install vista on a new installation

  My sata drive is not recognized by the installation of vista despite my having drivers available on a diskette. the application program updated driver, but there is none on the site of asus.

  * original title - I am unable to install vista on a clean install due to blocked by recognizing not the driver for fasttrack 376 of my SATA drive identified as promise 1 x 2 mirror raid *.

  Hello

  You must reach out to the ASUS Support to get the latest driver available for the hardware:

  ASUS support

  ASUS forums

  Also check the link given below; This thread may be of interest to you.

  Driver for Promise FastTrack 376 (tm) RAID controller

  Note: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to start - blue screen STOP: 0X0000007E

  original title: STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578)

  I was working on my laptop Acer Aspire and suddenly my restarted windows and then leave her unable to start and just show a blue screen with the error code as STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578).

  I tried to run in safe mode, then even I tried all the options available in the Advanced menu to restart that we get after pressing F8 but just fails. Repair of the system showed the error Impossible to repair in the same way his unable to restore and unable to start with last successful boot setting.

  Kindly let me know what to do I have lots of important data in my hard drive that I don't want to lose.

  Hello

  Unless the drive itself is completely fried the data on disk can be recovered by putting the hard drive
  in another computer as 2nd or a case of external hard drive using a USB connection - then the data
  likely to be backed up or copied to other media.

  Of course, the major problem is that the system does not boot even in Safe Mode.

  Setup/settings (BIOS/CMOS) often F2 so screen shows that it boots CD/DVD on the 1st in the boot order-
  Start with a Windows 7 disc and try the Startup Repair tool. Also, try restoring the system from there. (Don't forget to)
  Set the boot order to when.)

  Those who cannot not helped at all and will need you the help of a real computer store (no leeks and)
  Displays a BestBuy or other stores) or system manufacturer support.

  =================================================================

  Here are the usual methods to troubleshoot the bluescreens if you have access to some and still have a
  problem.

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top 3 answers.

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  -----------------------------------------------------------------------------------------------------------------

  The system has RAID? If so, it is very suspicious.

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
  interpret, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
  the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
  has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
  Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Make sure all new hardware that is installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable
  or remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
  Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
  in Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the boot of the computer service
  by using the Recovery Console, and then by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You should also
  Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or
  Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
  BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
  space, reduce the number of files on the disk drive hard target. Find and delete any temporary
  the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
  contain fragments of file saved to disk scans. You can also use another hard drive with more drive
  free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="">
  * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-
  -------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard event viewer
  Windows. TIP - Options - Advanced filter allows you to see a time rather
  of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during ' blue screen of the.
  death ' crashes and displays information about all accidents of a table.
  Free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
  However, there are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Does not work
  tell all possible driver issues).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Unable to start: freeze "starting Windows."

  I am unable to boot Vista. The start Windows logo appears, the drive activity light flashes for a few seconds and remains off.

  A sure start Gets the extent of loading CLASSPNP. SYS, and then freezes.

  Technical data: Sony Vaio VGN-FZ280. Vista SP2

  First of all, the problem came when I was watching a DVD on an external display (HDMI). The computer has suddenly just reset and would not restart afterwards.

  If Safe Mode does not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• I'm unable to start Firefox. To get the message that it is already running. Cannot find my profile using '% APPDATA%\Mozilla\Firefox\Profiles| '. What should I do

  I'm unable to start Firefox. To get the message that it is already running. Cannot find my profile using '% APPDATA%\Mozilla\Firefox\Profiles| '. Restarting my computer did not help. Because I had this problem I also noticed that all my favorites that I had copied in Windows Internet Explorer also disappeared. I use Firefox as my main search engine and usually do not use Internet Explorer. I am running Windows 7 on my machine.

  Try this add on the profile folder

• Unable to start after you run the product recovery disc

  Hello

  My laptop was a dual boot with windows XP SP3 and ubuntu

  1. He was infected by the virus and when I tried to clean it I removed the wrong file "services.exe", whereas windows does not work good there

  2. when I tried to uninstall the windows update, I get the error following error: 1068: the dependency service or group could not start

  3. so today, I found the toshiba recovery disks, I run and it commpleted, but now am not able to start my laptop.

  4. when I try to re - install windiws xp I got the error below "couln can't find NTLDR.

  Guys, your help will be much appreciated

  Hello

  > I run and it filled, but now am unable to start my laptop

  Are you sure that installation completed successfully? Looks like the damaged MBR or cannot be attributed