Unable to trigger the nissin Di622 flash Canon 430ex II

Similar Questions

• Can you use Pocket wizards to trigger the HVLF60M Sony flash when it is out of the unit with the A7R?

  Can you use Pocket wizards to trigger the HVLF60M Sony flash when it is out of the unit with the A7R?  How about studio flashes (Alien Bees)? I just sold my Canon gear and moved to Sony, but I need advice on how to trigger wireless flashes.  Thanks for any help you can provide.

  Larry

  LarryMarshall, Any Trigger of manual Radio should work.  Assistants of pocket or RadioPoppers.

  But there are a few problems with the 60 m.

  (1) it doesn't have a PC or a 1/8 port to connect directly to a Rec Radio of any brand.

  (2) you WILL NEED to buy or use a hot shoe with a PORT adapter... 1/8 according to the sync cable or PC you may already own.

  (3) you WILL NEED to 'Check' to 'ensure' that trigger the 60 m SHAFT is aligned with the center of contact your hotshoe adapter hot with a PORT... because some adapters won't online upward with the 60 m Flash... who fooled you into believing that it does not work.  When, in fact, it's just the PIN which is not aligning with ALL the hot shoe adapters.

  It will work... you just have to be careful... and know of the gatcha.

  The 60 m PUT claw is not fully compatible with all... hot shoe adapters and there that to do with how PUT 60 m flash foot aligns the trigger ROD.

  I triggered the 60 m in flash with RadioPoppers... in the manual... so, I know it works.

  It is, manual release of the waste of the 60 m flash TTL/HSS abilitys.    What is needed is for SONY to develop and deliver a Radio trigger Solution.  Which would be TTL/HSS and you allow to 'Control' the Flash too... from the camera.

  It is the power of a Flash of modern Radio System.

  Manual triggers are old school.

  p.s. the A7r/A7 can easily trigger flashes of Studio with Pocket Wizzards or RadioPoppers... or probably triggers of manual.    Just be careful if the brand you choose is reliable.

  Pocket wizzards and RadioPoppers were the choice of PRO for years.  Because they are reliable.

• VTech App unable to see the Installation of Flash

  I am installing Lodge Vtech learning to get Christmas present daughter up and run in advance. It downloads and installs OK, but claims of Flash that is installed and works well in IE. I uninstalled and reinstalled all the Flash and the Vtech App nothing helps. Am I missing security affecting somewhere? Versions are Vista (64-bit), IE 8 and 11 of the latest Flash. I did all the tools listed settings controls and made IE so that the Flash plugin is activated. I realize this good can be a problem in Microsoft, but any help would be appreciated gratefully.

  Hello

  I suggest you contact VTech to get help

• Unable to show the 700 d even canon RAW photo files after download of Canon codec.

  Just got a new digital camera from canon 700 d. updated canon 400 d.

  I am using windows 7 32-bit and used to be able to view raw photos in my old 400 d windows Explorer, but now I get an error message saying that windows is not recogise the raw format. I have updated to the last cannon and the microsoft codecs, but still cannot display files.

  Thank you

  This is because the codec does not yet support your camera according to the http://www.microsoft.com/en-us/download/details.aspx?id=26829

  • Microsoft Camera Codec Pack provides support for the following formats of device:
  • Canon: Digital Rebel XT, Digital Rebel XTi, EOS 10 d, EOS 20 d, EOS 30 d, EOS 40 d, EOS 50 d Digital, EOS 60 d, EOS 300 d, EOS 350 d, EOS 400 d, EOS 450 d, EOS 500 d, EOS 550 d, EOS 600 d, EOS 650 d, EOS 1000 d, EOS1100D, EOS 5 d, EOS 5 d Mark II, EOS 5 d Mark III, EOS 6 d, EOS 7 d Digital, EOS D30, EOS D60, EOS Digital Rebel, EOS Kiss Digital , EOS Kiss Digital N, EOS Kiss Digital X, EOS Kiss F, EOS Kiss X 2, EOS Kiss X 3, EOS Kiss X 4, EOS Kiss X 5, EOS Kiss X6i, EOS Kiss X 50, M EOS, EOS Rebel T1i, EOS Rebel T2i, EOS Rebel T3, EOS Rebel T3i, EOS Rebel T4i, EOS Rebel XS, EOS Rebel XSi, EOS - 1 d, EOS - 1 d, EOS - 1 d Mark II , EOS - 1 d Mark II N, EOS - 1 d Mark III, EOS - 1 d Mark IV, EOS - 1Ds, EOS - 1Ds Mark II, EOS - 1Ds Mark III, PowerShot G1 X G2, PowerShot G3 PowerShot, PowerShot G5, G6 PowerShot, PowerShot G9, PowerShot G10, PowerShot G11, PowerShot G12, PowerShot G15, PowerShot Pro1, PowerShot S90, PowerShot S95, PowerShot S100, PowerShot S110, PowerShot SX1 IS, PowerShot HS SX50

  and read the info on the Canon site, their codec stand alone does not support the 700 d.

  See if FastStone http://www.faststone.org/FSViewerDetail.htm works with your new camera.

  --
  Barb

  MVP Windows Entertainment and connected home

  My Blog - http://digitalmediaphile.com/

  Application Windows 8 Blog Reader of Barb connected world - http://apps.microsoft.com/windows/en-us/app/barbs-connected-world-blog/02f35769-52bf-461c-b1d5-06e54a58d298

• Unable to see the video of Flash Player in the Web sites

  I use Windows 7 x 64, with the Chrome browser OS a bit. Latest version of Flash Player 11.5.31.2 is installed but I can't see the video Flash Player embedded in Web sites. Why would it be?

  While leaving some useful information for other people who may encounter this problem:

  To help out we will need the following system information:

  -Operating system

  -Browser

  -Flash Player version - http://helpx.adobe.com/flash-player/kb/find-version-flash-player.html

  The first step to solve the problems with video playback is to work through the troubleshooting guide video for your operating system:

  -Windows - http://helpx.adobe.com/flash-player/kb/video-playback-issues.html#main_For_Windows_users

  -Mac - http://helpx.adobe.com/flash-player/kb/video-playback-issues.html#main_For_Mac_OS_users

  Problems sometimes video and audio are caused to a level lower and not directly related to Flash Player.  I recommend that you try the links below to see how they play.  If the problem exists with both, then Flash Player is most likely not the culprit because the HTML5 video link doesn't use Flash Player during playback.  You can check this by clicking on the HTML5 video and look for the words "On HTML5" at the bottom of the menu.

  -HTML5 video - http://www.youtube.com/watch?v=cTl3U6aSd2w&html5=True

  -Non-HTML5 video - http://www.youtube.com/watch?v=cTl3U6aSd2w

• What should I do when I receive the message 'unable to load the flash shockwave.

  What should I do when I receive the message 'unable to load the flash shockwave.

  Hello

   
  1. how many times you get this error message? This problem is limited to specific Web pages?

  2. Once you get this error message? What is your default browser?

  
  Find out what version of Internet Explorer you are using
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-out-which-version-of-Internet-Explorer-youre-using
  
  3. have you installed new hardware or software before the show?

  4. What is the operating system installed on the computer?

   
  5. are you logged in as administrator?
   
  
  Method 1:
  If you are facing problems with Internet Explorer 9, I suggest you read the article and try to run theFix it:
  Troubleshoot Internet Explorer to IE quick, safe and stable
  http://support.Microsoft.com/GP/pc_ie_start
  Note: Note that the reset Internet Explorer (IE) resets all settings defined by the user, including those established by the installed extensions, toolbars and other add-ons for IE by default. This includes all the security, privacy and settings area. Also this will erase browsing history, delete all temporary Internet, cookies, form data files and especially all the passwords.
   
  Method 2:
   
  a. search for Internet Explorer in the start menu.
   
  b. right click and select "Run as Administrator".
   
  Check if the problem occurs.
   
   
  Method 3: Uninstall and reinstall Adobe Shockwave
   
  To uninstall a program
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program
   
  
  I also suggest you to download and install the latest version of Adobe Shockwave player and check if that helps:
  
  http://get.Adobe.com/Shockwave/
  Provide more information about the issue so that we can better help you.
   
  I hope this helps.

• Unable to save the files to my device (Flash disk)

  Unable to save the files in my flash drive. It is given the message that it is complete, although it is not even half full. Furthermore, when I tried to eject, there will be a message that I have shuold close all files using even when there is none.

  Thank you

  First of all, I would like to make a backup of all the files somewhere safe. Just in case something goes wrong. I would like to make a copy of the files on the computer. Format the USB. Then copy the files over. If after a format, it still has the same problem or she leaves you nothing copy on then the memory stick may be dying on you and her is to buy another.

  Good luck

  Free Support Tools

• Is there a way to manually activate the built in FLASH on my Canon Rebel T3i?

  Is there a way to manually activate the built in FLASH on my Canon Rebel T3i? I can't find the place to do this.
  Thank you.

  You can also use the "Programming" mode  Program mode allows the camera to choose the initial settings, but unlike the automatic mode where you cannot override the decisions of the exhibition, you CAN override the decisions of the exhibition in programming mode if you wish.

  If you choose the programming mode, press the button to bring up the flash and then don't bother to circumvent the decisions of exposure of the camera then it will work a lot like automatic mode.

• virtual flash resources management is unable to recognize the SSD not (marked as ssd)

  Hi all

  In my lab at home, I am able to do with VMware vSphere Flash Read Cache (vFRC) practical, I don't have SSD on my desk.

  In vmware workstation-11, I created a 5.5 esxi and added the local hard disk. It is an SSD not and I've marked as SSD.

  in VC the reader is now considered ssd however in VMware vSphere resource management Flash when I click on add ability he is unable to see the SSD (not marked as ssd).

  Any suggestions on how to turn it on.

  Thank you

  Vaibhav

  As far as I KNOW, the SSDS should be visible as "local". You can run the command.esxcli storage core device list -d   and check if the device is showing as local ssd

  >>

  It was a disk formatted with the vmfs.

  >>

  I think that the disc does not have vmfs. Can you remove the vmfs and propose a normal, unpartitioned ssd drive

• I had to uninstall flash player, but am unable to install the update.  I have reset the Mac Book but am still unable to install the update.

  Safari: Version 8.0.6 (10600.6.3)

  Mac Book: MacBook Pro (retina, 13 inch, mid-2014)

  I had to uninstall flash player, but am unable to install the update.  I have reset the PRAM book Mac & NVRAM + SMC re-set, but I am still unable to install the update via Safari or FireFox

  Still due once sort myself

  I downloaded the offline install app;

  http://fpdownload.Macromedia.com/pub/flashplayer/latest/help/install_flash_player_osx.dmg

  Up and running

• installation: my version of elements adobe 12 is unable to read the raw files from my canon 70 d SLR.

  my version of elements adobe 12 is unable to read the raw files from my canon 70 d SLR.

  You need Camera Raw 8.2 or higher.

  12 items delivered with 8.1.

  Click Help > updates to update Camera Raw

• Flash Builder 4.5 unable to find the debug version of Flash Player.

  I'm running into the following error message:

  C:\Windows\System32\Macromed\Flash\NPSWF32.dll

  Flash Builder cannot locate the required Adobe Flash player debug version. You should perhaps install the debug version of Flash Player or reinstall Flash Builder.

  You want to try to debug using the current version?

  I already went to the binding dialog box provided to download Flash Player debug builds.  I installed the Plugin and AX versions of the debugger.  Reboot all browsers, Flash Builder and restarted the PC for good measure.  I spent a good amount of time looking for information on this issue.  All the threads I found who were related to this issue was to present one must be achievable.  So I'm starting a thread on this problem.

  I'm running Flash Builder 4.5 on Windows Vista 32-bit.  I tried to use 3.6.24 FireFox and IE 8.0.6001.

  I started with the trial version and then purchased the license online.  I do not know if that has an impact.

  All the information to diagnose this problem would be greatly appreciated.

  Hi emat3d,

  Try to uninstall Flash Player with this uninstaller from Adobe, please make sure that you close all applications that may be using Flash Player. Then try again to install your Flash Player debugger. He has solved it for me.

• Unable to find the devices on the network of field

  Hello

  I'm currently setting up a network of field. The problem I have is:

  After the reboot of the PS-2000, everything starts up as usual, but after 15 seconds, the A, B, C, D LEDs do not turn off, and READY LEDs on the IO modules never turn on. The STATUS LED does not blink, there is no specific errors. The POWER LEDS on the set of the modules is on. I am unable to use the FIND FEATURES within the NOT-MAX, a 'Connection Timed Out' (or something to that effect) error message occurs.

  I have correctly configured an IP address on the PS-2000, I am able to view the files on the Flash using the FTP transfer in NOR-MAX, I updated the Firmware LabVIEW RT v7.0.0. I tried to reinstall the firmwar
  e and resetting the PS-2000, but nothing helped.

  To simplify the issue, I unplugged the PS-2000 from the rest of the basics of connection. I inspected the
  pine trees on the side of the module and they looked fine. I couldn't find all other versions of the Firmware for the PS-2000 on the NI download site, just in case my version has been altered. With this configuration, the A, B, C, D LEDs are still on, and the FIND DEVICES (not that there there) always times out.

  Then I tried to plug in a FP-TB-10 (with only input modules out there, so that there would be no external power required), and I still have the same problems.

  Material used:
  PS-2000
  -2 * FP - TB - 10 popular with a mix of I/AO/DI/DO
  FP-QUAD-510
  -FP-PG-522

  Power supply:
  -Kepco power out 16 VDC and approximately 0.4 A (+ terminal connected to V and neutral terminal connected to C)

  Software used:
  -LabVIEW Professional 7 with RT
  -MAX 3.0

  Unfortunately most
  the user manuals still refer to the field Point, as opposed to the NOT-MAX Explorer.

  Any suggestions for my experiences above would be welcome! Is there anywhere I can download the firmware Lv7.0.0 RT? Everyone knows about similar problems with LV7?

  Thank you!

  I will answer this myself!

  The issue proved to be a limited set of software installed on the FP2000. When I was installing the software, setting up NO-MAX, the only available software is LabVIEW RT v7.0.0.

  When you install the software (from NOR-MAX) on the ps2000 for the first time, the following text should be available:

  -Control environment FieldPoint
  -Manager of VI FieldPoint
  -LabVIEW RT
  -RT OR Serial
  NI-VISA
  OR-Watchdog

  If none of them are not available, the module PS, or downloadable from the NOT-MAX, then not all device drivers have been installed on the PC.

  Use your device provided with LabVIEW drivers CD to install all the necessary drivers of RT.

• Flash Canon 600 EX - Speedite RT - flash using testfire erratic power

  Hello

  For a photography assignment, I had to use an off-camera flash (using the testfire) to capture the different poses of a subject during a long exposure.

  However, by pressing the button testfire produced variable results:

  1. the subject was reasonably informed.

  2. the power of the Flash was weak, leading to a very underexposed subject

  3. the test button would not fire at all.

  Now, the obvious cause of this erratic behavior would be batteries to be replaced. However battery replacement (using brand batteries good long life) does not solve the problem.

  If someone else has countered this problem and if so, is there a solution?

  Kind regards

  W, which has no such assignment

  When you trigger the test button, the amount of energy it will draw depend on the mode and the settings of the flash.

  Mode you are using (manual or E - TTL) and if manual, what power level you have set (for example 1/1 = full, but there is also a 1/2, 1/4, 1/8, etc.)

  If give you him a burst of full power in manual mode, you have to wait for the flash to recycle the capacitors before it is ready to fire again.  The capacitors are a bit like rechargeable batteries except for the rate at which you can drain a battery is somewhat limited and a capacitor can pour out his incredibly fast energy.  How flash actually works is to have the batteries to recharge the capacitors until it has enough fire power, and then the power of the flash capacitors (because they can send a power tip to the strobe light).

  Most people tend to use E-TTL/E-TTL II mode - or - they use it in manual mode (M).  But there are other modes.

  If you want to manually control the flash for your situation, then press the "Mode" button repeatedly until you see the "M", displayed in the upper left corner of the LCD screen (now you are in "Manual" mode and the flash will always fire at the same power level in E - TTL mode, it will try to automatically detect the amount of energy uses and many things can give you varying results because frankly) You asked the flash to automatically detect and vary the power level).

  Manual mode is only half the fun... now press the soft key under the LCD panel around the "+/-" and allows you to control the power level.  By default it will pull at full power (1/1).  But you can now turn the wheel to reduce the power level (and you probably want to reduce the power level because 1/1 is a lot of power.)   For example... maybe 1/8 power would be more reasonable... or maybe 1/4 power.

  But the other reason to use the manual mode is once you set the power level, it will ALWAYS trigger with the same amount of power (until you change.)

  Remember that when you use the manual flash, flash has a 'falling' effect that causes the light seems less intense if the flash is farther or closer to the object.  This is what we call the 'inverse rule of the square law' and it's a law of Physics (not do around him - sorry.)  This means that if you want your subject to get uniform illumination so not only you must use the "manual" mode and set it to a specific for every time... power level but the flash itself must be at the same distance from the subject (if the subject moves... then you need to Flash for the maintenance of this uniform for each shot distance.)

• Get slaves 600EX-RT to fire only via the pop-up Flash

  I have a set up as slave and controlled by the 60 d 600EX-RT using the pop-up flash.  I have the 60 d settings for the slave to fire single pages 140 and 141 of the 60 d manual.  However, in this context the pop-up flash fires again.  At the end of page 141, he said "even if you disable the built-in flash of firing, it is always light to control the slave unit".  Is there no way to disable the pop-up flashing?  Otherwise you never truly unique off-camera flash.  Thank you.

  Is there no way to disable the pop-up flashing?  Otherwise you never truly unique off-camera flash.  Thank you.

  No, if you want to trigger a slave camera because it uses the pop-up flash as the triggering of the slave device.

  Yes, you get unique off-camera Flash because although pop-up flashes, it's only a pre-flash to trigger the slave.  In this configuration, that the pop-up does not contribute to the actual exposure, all this happens before the opening of the shutter.