Under Vista, my fan starts and stops, makes a loud sound and the power light flashes
My fan starts and stops, resembles a car reving his engine. The power led also flashes. Gateway gt
* original title - my fan starts and stops, resembles a car reving his engine. The power light flashes too *.
Hello
If you have nothing on the screen, including a splash with logo screeen, etc, contact gateway if under warranty
If it is under warranty, contact a local reputable computer repair workshop
Tags: Windows
Similar Questions
-
KDL-46XBR9 shuts off and the power light flashes red
KDL-46XBR9 shuts off and the power light flashes red
It flashes ten times, then rehearsals.
-
Help.
I have a HP Pavilion dv6-2088dx and have had for a little less than two years now. About 8 months ago, I replaced the original battery with a long life Rayovac battery. Recently my laptop power light has been constantly intermittently to about 1 flash every 2 seconds, regardless of the level load and/or if its plugged to the power source. What exactly my computer is trying to tell me? Thanks for the help in advance
-Kyle
I found the link to your question. I hope this helps.
-
HP Pavilion dv3t notebook. Each time get adapter connect to the laptop, it takes at least 10 minutes to get the AC adapter and power indicator light on. Sometimes it does not light on all day. It always happens any with the battery or not.
If I start the laptop with the light on the AC adapter and the power light, no matter how I move the power cord, it maintains support, works very well.
But if I start the laptop without the light on the AC adapter and the power led on even with the, i.e. start with the battery as power, no matter how I move the power cord, the led on the AC adapter and the light, i.e. no charge. He stops until the battery drain.
I believe that the AC adapter is good. But I have no idea why he has trouble in the light on the AC adapter and the power light on after to connect to the laptop.
Dv6 had a somewhat similar problem that was treated with a BIOS upgrade. I watched the latest BIOS for your laptop and there is nothing about a problem of load, however. If it works very well and also a long time that you turn it on with the AC plugged in but only has a problem with loading when you connect the adapter Windows runs, I'm tempted to say that it is a software problem as a problem with Windows power management. Maybe if you remove the hard drive, power supply, switch it on with battery only, then plug the adapter when you run in a pre-Windows environment, we can see if the same problem occurs. If it was my cell phone, I would also like to do the update BIOS level, just to see if maybe it would affect something. I could also try to run it from a Linux Live disc any and see if the same problem occurs in another operating system. Last resort I would begin focusing on the issues of possible material, as a module of taking bad AC, which is an other replaceable part that requires no welding.
-
Vista won't start and the startup repair can't find any problems
Have a Dell Inspiron under Vista 64 bit, which does not start. I have inserted the re installation DVD and ran the Startup Repair which could not detect a problem.
Diagnosis and repair are the following
----------------------
Managed last start: 2010-10-23 21:12:44 (GMT)
Number of repair attempts: 1
Details of the session
-------------------------------
System disk = \Device\Harddisk0
Windows directory = C:\Windows
AutoChk run = 0
Number of root causes = 1
Test performed
------------------------------
Name: Search for updates
Result: Completed successfully. Error code = 0 x 0
Take time = 0ms
The test is performed:
------------------------------------
Test the disc name: System
Result: Completed successfully. Error code = 0 x 0
Taking time = 0ms
Name: Troubleshooting disk
Result: Completed successfully. Error code = 0 x 0
Time taken = 218ms
The test is performed:
------------------------------------
Name: Metadata for the drive Test
Result: Completed successfully. Error code = 0 x 0
Time taken = 62ms
The test is performed:
------------------------------------
Names OS test target
Result:
Completed successfully. Error code = 0 x 0
Taking time = 188ms
The test is performed:
------------------------------------
Name: Checking content Volume
Result: Completed successfully. Error code = 0 x 0
Time taken = 140ms
The test is performed:
------------------------------------
Name: Diagnostic Boot manager
Result: Completed successfully. Error code = 0 x 0
Taking time = 78ms
The test is performed:
------------------------------------
Name: Diagnostic log for the system startup
Result: Completed successfully. Error code = 0 x 0
Taking time = 16ms
The test is performed:
------------------------------------
Name: event log diagnosis
Result: Completed successfully. Error code = 0 x 0
Time taken = 530ms
The test is performed:
------------------------------------
Rated: Internal audit of State
Result: Completed successfully. Error code = 0 x 0
Taking time = 0ms
The test is performed:
------------------------------------
Name: Start-up condition Test
Result: Completed successfully. Error code = 0 x 0
Taking time = 0ms
Root cause found:
-----------------------------
State of the start indicates that the OS booted successfully
But the laptop still wont start I tried to run chkdsk/r from the command line and was unable to do as he says Windows cannot run disk checking on this volume, because it is write protected. I don't know what to do now anyone no matter what ideas thanks in advance.
Seems odd. Startup Repair should have solved the problem.
Have you tried new reboot running?
Give it a shot...
Any chance that you have a "backup computer?
Try to do a full restore of the PC.
See how it goes...
Man is the only animal that laughs and cries; because it is the only animal that is struck by the difference between what things are and what they should be.
-
Vista will not start and the recovery disc does not
Hey all,.
Vista has just started to freeze during the boot at crcdisk.sys today
I tried using the recovery disk, but it won't work, says the root prolem is corrupt system or something like that.
If you need more information please ask!
Can someone help me?
Thanks in advance!
Hello
Yes, it would make a difference to what is the Startup Repair tool. Vista startup repair only works on his own Bootstrapper. You replaced one with GRUB, so you should use the ' nix tools to fix it. However, you indicated earlier that the problem occurs after the start load Vista, so this isn't something the Startup Repair tool will correct and is not likely to solve your problem.
Your running recovery disk will also likely be wipe the GRUB bootloader, but you don't really have a lot of options when it comes to a corrupted installation. If you are unable to correct the problem to running chkdsk, then it is unlikely that any other action will work. You're stuck with the relocation.
Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org
-
Qosmio X 500 does not start and the power LED is flashing every 5 seconds
Hello
I need help my X 500 does not start now. I tried to launch the NB as usual and suddenly the X 500 start or even power up.If I press the power button / stop it makes no noise, the power LED on the button and the second power LED just bliks once and turns on and keep blinking every 5 seconds.
I tried to:
* Remove battery and power up with AC only
* power only to batteries
* remove the battery power button hold for 30 seconds and over power with AC, battery only athenbut it did not help.
I checked the LEDs AC & battery, but they do not blink, they are just RED, so there is no problem in battery or AC.
No idea where could be the problem?
Thanks for help
FrantisekHello
The failure of RAM could be the reason for this behavior of the laptop.
Remove the RAM modules with good modules tested and check the functionality of the laptop.
In the case of RAM isn t the troublemaker, the motherboard could be affected.Good luck and share your experience with us.
-
I was upgrading my HP DV7-3162nr for windows 10 when all of a sudden the laptop stopped working and would not turn.
The power adapter is plugged in and battery led was flashing. Now battery led does not at all depend on. When I press the Start button the laptop would try to start then turn off after about one second. However most of the time when when I press the button nothing happens.
I took out the battery and tried to immediately start the alternating current, but the laptop is like there is no power. The led near the power connector is on the AC adapter is plugged in. I checked the tension between the adapter and it is correct to about 19 volts, I even loaded to 1.5 Amps and voltage remained close to 19 volts. I tried now on the button for more than one minute with applied power (no battery or AC) and no change when I tried to start with just AC. The battery is old, but shouldn't the laptop run on just the AC adapter with the battery installed? I do not think that windows 10 has done this, but it's a weird coincidense that he died during the upgrade.
I read about simular problems with flags of HP but nothing exactly like it. The fact that I can not turn on the laptop with just the adapter seems to be a problem really bad.
Anyone has any ideas I can try to let me know
I was able to fix my laptop.
I thought that it must be a hardware problem, because the laptop would not run just the adapter. And the adapter was good, as I said, he had the right voltage and can support the load. So after looking at a lot of U tube videos on how to disassemble laptops and looking for schematics on the laptop which I couldn't find. I disassembled the laptop and a beep on the load circuit and it showing. What I found, it was a bad MosFet at the beginning of the charging circuit. The MosFet P/N P0603BDG has shorted door to the Source. I was able to get the part of China via Ebay for less than $5.00 total and it took a week to arrive.
Now, the laptop charging the new battery and works very well. I could have found the bad MosFet faster if I had diagrams. Does anyone know if it is possible to get the schematics for this HP laptop? I found a manual and it helped a bit to disassemble the laptop, but he had nothing on the main map.
This problem is now solved hope it helps someone out there.
-
Vista will not start and the Startup Repair boots in a blue screen of death. Why?
I select run a startup repair, and it goes straight to the blue screen. When I start normally it justs sits there with the bar go green around and around. System Restore also dosen't help. I can boot into safe mode, but I don't know of other programs of Diagnostics. In addition, no virus. HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!
Read the posts by spirit MVP in the following thread on the Blue Screen of Death. They should help you solve your problem. http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/8cd8362e-7d06-46fb-afd7-84d54b6a8ea7.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
I have
Your phone can not be resolved. Apple will offer you a discount on a replacement.
-
Qosmio F20 won't start - power light flashes orange
My Qosmio F20-149 crashed yesterday and I was not able to get it working again. When I try to turn it on, the power light flashes on and outside (on: 1 sec, off: 1 sec) and the cooler fan operates at full power. When I press a key, there is a genre or a sound error. otherwise no reaction of the laptop; even the CD player does not open.
I did no RAM-implementation to date, and I use the original power supply Toshiba. I tried from the laptop using only the battery, only power and on both. No change in the reaction. I tried all possible combinations (with a free one, both... etc) of my two cards, RAM (512 + 512) and still no use.
I am really puzzled.
If I understand you just your laptop sends a blink code. Copy the following code appears so laptop has detected a problem with the electronic power supply.
In this case, there is nothing that you can do and the laptop must be sent to the service provider allowed the closest.They have manuals containing instructions and the exact description of the code how do I solve this problem.
Sorry, buddy, but I do not think that anyone here can offer an accurate diagnosis for that matter. -
Satellite L500 is OFF and the Green LED flashes if hooked on sector
Help!
I have a L500 which is not outside the green light flashes when the power cable is plugged in, but does nothing else
Hello
What indicator do you mean exactly?
DC (first on left) indicator lights up green when the properly feeding the power adapter. If the output voltage is abnormal or if breakdowns computers power indicator lights.
The other indicator (power led second from left) lights green when the computer is turned on. If you turn off the computer to sleep, this LED starts blinking Orange.
Also if there is a failure of memory Power LED repeatedly flashes
0.5 sec and off 0.5 sec
If there is a problem with the slot A the LED flashes two times orange then green once
If there is an error in the B slot, the LED flashes orange green once then twice
If there is error in the slot A and B the LED flashes two times in orange and green.But if the power light flashes green only, I guess there is a motherboard problem.
-
The speakers click when the fan starts and stops Equium A100-147
I recently bought the 100-147 satellite and noticed that a click comes from the speakers (or headphones or external speakers) when the fan starts up and even when the fan stops. Sometimes it s quite remarkable, other times not so remarkable.
Everyone can hear that click? If it's normal, I can live with that, otherwise I will return it for repair. Any comment please?
In addition, it seems slow at startup and shut down. Put into service takes 2 minutes and 35 seconds, and stop to 33 seconds. Is this normal bearing in mind, it is running MCE? I have loaded additional software such as Itunes, Nero, Office 2000, Photoshop 5.0 etc.
Thank you for reading.
Clicking noise when the fan starts or stops turning is not uncommon. On my satellite a similar sound will appear when the fans begin to turn or the HARD disk starts to spin.
Then worry about don t, I think its OK.The start-up procedure can take several times when a lot of applications and software to load at the beginning. Equium A100 seems to be one of the newer laptops, and I assume that different applications Toshiba load at the beginning.
Also an Antivirus applications could extend the startup procedure.You might try testing something. Disable the antivirus of loading at the beginning and check if the laptop will start faster.
It s even with stops. All background processes that are run in the context of the operating system should be closed until the laptop shuts down completely.
-
Satellite A110-180 - fan starts but stops after a few seconds
Hello
I have a Toshiba Satellite A110-180 and when I turn on the computer, the fan turns on but it stops in a few seconds and starts again in a while and stops again and starts... Then the laptop gets heat quickly.
I bought the laptop about 5 years ago, so I think the problem is the fan or the circuit that controls the fan. Can someone who has had the same problem make sure that the fan is the problem?
The fan part number is ATZHG000500. Does anyone know if a fan with P/N ATZHG000100 is compatible with my laptop, or if I can use another fan?
Thanks for your help,
Hey Wiley,
First of all it of normal that the fan starts and after a few seconds, or 1 minute stops. Depending on the programs you run again the departure of fan after a few seconds or minutes. So, theoretically, it of normal what is happening.
But if your laptop is almost 5 years old, you should try to clean. So I can recommend jet of compressed air. This could blow out the dust from the cooling fans. It is very cheap but very useful.
Check it!In addition, I think that the thermal paste should be renewed a technicians authorized laptop can help you and answer if the other fan part number fits in your laptop. :)
-
Re: Satellite C660 - fan starts then stops
Hello
Sorry for my English, I'm French, I have a Toshiba Satellite C660 laptop a few days ago and I noticed that the fan starts and stops every minute at any time when the temperature exceeds about 40 degrees (noted with SpeedFan).
Even if I'm just the desktop, the Internet. However, it does not heat up much. Is this normal?Before I had a laptop and the fan stops, but almost never had low-noise. I prefer it, but it's can be a simple matter of habit for the Toshiba...?
Hello
Try it please change cooling method option in the advanced power settings.
Open power options > n a click your power profile that you use > choose the advanced power options > Toshiba Power Saver Settings > cooling method > change two optimized battery options.
I think that this will reduce fan activity.
Please test and send feedback.
Maybe you are looking for
-
I would like to rent a movie from iTunes on my ipad2air and watch when I'm on a plane. Make her pay on iTunes at home and download on my iPad? So can I watch it on the plane? How much time, you have to keep a movie? And when my time expired ihas it a
-
Firmware for DVD - RAM Mat * a UJ - 850 s in Satellite L40 - 14F
Hello. I would like to ask who is available update of firmware for Mat * a DVD - RAM UJ-850 s located in the laptop Toshiba Satellite L40 - 14F. I can't find it on Panasonic/Matt * a web site. Thanks for the replies.
-
IntelliPoint how leave Mac OS to manage all the buttons
I sometimes use the mouse on the left side and sometimes on the right side. I exchange the click and click secondary preferential IntelliPoint, which is a pain to move 6 clicks every time. When accidentally, I changed the main mouse button Mac prefer
-
* Original title: Internet connection problem It has red cross standing in the network icon and I can't connect to internet via USB modem or WiFi. It is also not detect any wireless network.
-
Hi allI have a report, each page has a number of records, but there is a space at the bottom of the page,I want to fill this space with records? How to do?How maximiza the number of records displayed?I tried the property of "maximum entries displayed