Understand the marker data storage

Similar Questions

• Understand the diagnosis - hardware/storage

  Just ran a report system on my MacBook Pro 2011 and admit really, I don't understand what the reports but am a little worried to see Toshiba comes in diagnostics for hardware/storage. Macintosh HD shows in the logical volume group, but physical Volumes as it shows

  disk0s2 with a device name and the media from TOSHIBA. This is maybe quite normal and I just never noticed it before; However, I am now worrying that maybe I was hacked? How will I know what it is? Could we have a flash drive I used in the past but is no longer connected?

  Purchase spare parts from toshiba (among others)

• The connection data storage series

  Hi all

  I'm relatively new to LabView, I'm trying to store and analyze the values of a material non-Labview via an rs-232 connection.

  I have two devices on ports COM1 and COM2. COM2 sends a value that I want to store it in a table. COM 2 points will be a sinusoid somewhat in a few seconds. I would like to compare these living to generate values: the peak values max and min, the peak to peak and average values (I know LabView a signal icons for this, I'm not sure how to wire it upward).

  I have attached the vi.

  Thank you for your time and your help.

  Kelvin R.

  The series connection is irrelevant. What you need to know is something as simple as a while loop and register shift. If you want to make a continuous writing and reading, then place a while loop around reading VISA and VISA. Using the button run continuously is false. It's a special debug mode. The shift register can be something as simple as a table build where you add a new value for each iteration.

  Eliminate these instructions box if you always want to do something. You have configured serial ports to complete reading on a character of endpoints that use the VISA to the Serial Port bytes is bad.

  Before posting again, run the VI so that there is actually data on all of the controls and indicators. Go to Edition > use current default values, save the VI and fix them.

• How to get the ip address of the data storage device

  Hi all

  I developed a project now and you need to distinguish a virtual machine is saved to the device local ESX or remote network storage device.

  I found the data store object in which the virtual machine resides by vi sdk, but could not find the address of the device that includes this data store.

  How to get the ip address of the coding data storage device, which includes the virtual machine? I need your help.

  Thank you in advance.

  How do you try to make a query. Storage devices provides a logic unit number no, there is no IP address for it.

  You can check the same for the storage on vCenter view

• Rejected... We found that your application does not follow guidelines iOS of data storage,

  Where and how can I fix it?

  We found that your application does not follow the guidelines data storage iOS , which is required by the App Store Review Guidelines .

  
  

  In particular, we found that of the launch or download content, your application stores 3.54 MB. To check the amount of data is to store your application:

  
  

  -Install and run your application

  -Go to settings > iCloud > storage and backup > storage management

  -If necessary, press "view all applications.

  -Control the storage of your application

  
  

  The iOS data storage guidelines that only content that the user creates using your application, for example, documents, new files, changes, etc., must be backed up by iCloud.

  
  

  Temporary files used by your application must only be stored in the directory/tmp. don't forget to delete the files stored in this location when the user quits the application.

  Data that can be re-created, but must persist for proper functioning of your app - or because customers expect it to be available for offline use - must be marked with the "do not back upward" attribute. For NSURL objects, add the NSURLIsExcludedFromBackupKey attribute to prevent the backup of the file. For CFURLRef objects, use the kCFURLIsExcludedFromBackupKey attribute.

  You submit an application kiosk, right? This error is still under investigation, but the current solution is to create SD (1024 x 768/768 x 1024) coverage of the images for your renderings folio HD (2048 x 1536) and try again.

  More info here:

  http://forums.Adobe.com/message/4730637#4730637

• error 2558 with open data storage express vi.

  I have the appropriate Tektronix installed plugin and when I use the Open Data Storage Express to create new vi *. WFM file I get error-2558 indicating that my system does not have the software installed to support the file type. I use the 2015 SP1 version. Anyone else see this problem? What am I mising here?

  I can't find an easy way or direct to do. There may be a way to convert a file that is saved in a different format if you can find (or create) a file converter. What is your ultimate goal for writing a. WFM file? This will be used by a device that only recognizes. WFM files?

• VM have been storage vMotioned to another data store, and now I have 3 VM with white "!" inside a red square and I want to understand the cause of this.

  VM have been storage vMotioned to another data store, and now I have 3 VM with white "!" inside a red square and I want to understand the cause of this.

  Can you try to make a vmotion host and see if it gets resolved? If not, can you close the virtual machine and start again? I have seen this problem before and a stop and start resolved.

• Need help with the data storage store, local array and network connections

  Need help with my ESXi 4.1 installation

  My hardware:

  I built a server with an Asus P6T whitebox, i7 920, 12 Gig RAM, NIC, Intel Pro1000 PT Quad, 3ware 9650SE-12ML with 8 1.5 TB SATA green in a raid 6 array gives me about 8 + TB with a spare drive all housed within a NORCO RPC-4220 4U Rackmount Server chassis.  I also have a 500 GB SATA drive which will hold the ESXi and virtual machines.

  The network includes a firewall, Netgear Prosafe FVS336G, GS724Tv of Netgear ProSafe 24 port Gigabit Managed Switch on a dhcp cable modem internet service provider.

  I also have 2 old NetGear SC101T NAS disks (4to) I want to connect to the system how some - at a later date have... data on them and want to transfer to the new storage array. I always looking into the question of whether they will work with ESXi 4.1, or I might have to only access it through Windows XP.

  My Situation:

  I have already installed ESXi 4.1 and vsphere client with no problems and it is connected to a dhcp cable internet service.  I've set up host via a dynamic DNS service name give me a static hostname on the internet.  I installed three machines to virtual OS successfully at the moment and now want to first start by creating a multimedia storage server which will use some of this new 8 TB array, then separate data storage for use with a web server small overhead storage and a backup.  It is a domestic installation.

  Help with the data store and network:

  I was doing some reading, because I'm new to this, and it looks like I'll probably want to set up my table via ESXi as a nfs disk format.  Now, the data store is usually in another physical box from what I understand, but I put my readers and ESXi all in the same box.  I'm not sure that the best way to put in place with grouped network cards, but I want to make this work.

  I understand that in ESXi 4.1 using iSCSi LUN must be less than 2 TB, but nfs - I should be able to add a bigger partition then 2 TB (for my multimedia) in nfs, right? or should I still add it separately as a separate 2 TB drives and then extend them to get the biggest space.

  Any suggestions or direct resources showing examples on how to actually add some parts of the table as data warehouses separate nfs.  I know that to go to the configuration tab, and then select Add to storage, and then select nfs. I have not my picture, but it's here that I don't know what to do because ESXi 4.1 system already has an address, should I put the same thing to the new data store array also (will it work?), and what should I use for the name of the folder and the store of data... just do something to the top.  I thought to later install Openfiler (for a multimedia storage using this table server) as a virtual machine, use the table with esxi so that I can access the same storage space with widows and linux-based systems.

  I also know I have to find a way to better use my quad nic card... put in place of virtual switches, grouping, etc HELP?

  Any direction, assistance, similar facilities to sample, suggestions or resources that would help would be great. I did a lot of hunting, but still a little confused on how to best to put in place.

  You must think of VMDK files of large databases with records of random size guest go read some data (a DLL or an INI file), maybe write some data back, then go read other data. Some files are tiny, but certain DLLs are several megabytes. It's random i/o all and heavy on the search time. IO Opsys is small random operations that are often sequential (go read data, write data, go read other data,...) so that deadlines are critical to the overall performance. That's why people say OPS are / s of reference and forget the MBs flow. The only time where you bulk transfers are when you read media (ISO files).

  Well, now forget all this. Actually the disk activity will depend on the specific applications (database? mail server? machines compiler?), but the above is true for boots, and whenever applications are idle. You should see the profile to know.

  RAID 10 is faster (and often more reliable) than RAID 5 or RAID-6 except in certain specific cases. In General RAID 10 is ideal for many random writes, since the calculation of parity for RAID-5 and - 6 adds to the overall latency between command and response - latency is cumulative if a little slow here and a little slow it adds up to a lot of overall slow synchronous especially with e/s on a network. OTOH RAID-5 and -6 can produce faster readings due to the number of heads, so you can use it for virtual machines that transfer bulk. Test. You may find that you need several different types subdashboards for best results.

  You said 3ware, they have some good grades on their site, but don't believe it. With my 9650 that I found myself with only a couple of their recommendations-, I put the (simple) table for allocation size 256 k, nr_requests at 2 x the queue_depth and use the planner date limit. I had the habit for the Ext4 file system formatted with stride and stripe-width synced to the table and used the options large_files with fewer inodes (do not use the huge_files option unless you plan to have single VMDK files in the terabyte range). Use a cache of great reading in advance.

  Virtual machines use VMDK files in all cases except raw iSCSI LUN that they treat native disks. VMDK is easier to manage - you can make a backup by copying the file, you can move it to a PC and load it into another flavour of VMware, etc. There could be some features iSCSI to your San as a transparent migration but nothing for me. NFS has less chatter of Protocol if latency lower times to complete an operation. NFS is good to read and write a block of data, that's all it boils down to.

  UPS is good, but it won't help if something inside the machine explodes (UPS does nothing if the PC power supply goes down). If the RAID card has an option for a battery backup module, so it can contain some writings in memory and may end up the disk i/o after replacing the power supply. 3ware also limits the types of caching available if help is not installed, and you get just the right numbers with the module.

• Please help understand the mappings between PS & tables tables of data warehouse

  Hello
  We have OBIEE 11 g with OLIVIER 7.9.6.3 (HR Analytics) installation with Informatica PowerCenter SE 9.01 HF2. We use PeopleSoft HRMS 9.1 system source.
  Can you please help me how to understand the flow of data from end to end (or data model with relationship) between the PeopleSoft Tables and tables of data warehouse? Y at - it none available who liaises between the PeopleSoft HRMS tables and tables of data warehouse?
  
  PS We are new to Informatica workflow maps to find it very difficult to understand each mapping for each table.

  You can use the guide to table HR analytics on metalink. Here's the note:

  HR Analytics, Oracle Business Intelligence - Source tables uses [ID 1328607.1]

  This will show you the use of the main table. If you need the full line, you can use the data lineage Guide.

  If it helps, please mark as correct.

• How many gigabytes of data storage has the new Apple Watch series 2 and how many GB are free for music?

  How many gigabytes of data storage has the new Apple Watch series 2 and how many GB are free for music?

  Hello

  Apple has not yet announced the capacity of storage or the music of Apple Watch series 2 storage limit.

• root properties in the connected data store: error when accessing the date/time storage

  When you browse the properties my connected data store I get an error message when you try to read the value of the property of 'storage date/time': object doesn't support this property or method.

  Here is a minimal example:

  Dim oMyDataStore, MyProperty, oMyProperties
  
  Set oMyDataStore = Navigator.ConnectDataStoreByParameter ("TOC", "" & "C:\Program Files (x 86) \National 2012\Examples\Data\Example_data.tdm" & "" ')
  
  Set oMyProperties = oMyDataStore.RootElements (1). Properties
  
  For each MyProperty in oMyProperties
  
    Call MsgBoxDisp ("property name:" & MyProperty.Name & + "\n"&"property value:" & MyProperty.Value "")
  
  Next

  Why can I not access this particular property by default?

  Hi Phex,

  for the date/time properties, an object called UsiTimeDisp is returned. This object allows to that extend features of service as access to each part separately (day, year, hour, seconds,...) of your date/time value. If you want to print the value of time with MessageBoxDisp, you can use the VariantDate this object property.

  Your code might look like this then:

  Dim oMyDataStore, MyProperty, oMyProperties
  
  Set oMyDataStore = Navigator.ConnectDataStoreByParameter ("TOC", "" & "C:\Program Files (x 86) \National 2012\Examples\Data\Example_data.tdm" & "" ')
  
  Set oMyProperties = oMyDataStore.RootElements (1). Properties
  
  For each MyProperty in oMyProperties
  
    MyProperty.DataType = eTime Then
  
      Call MsgBoxDisp ("property name:" & MyProperty.Name & + "\n"&"property value:" & MyProperty.Value. ' ") VariantDate)
  
    On the other
  
      Call MsgBoxDisp ("property name:" & MyProperty.Name & + "\n"&"property value:" & MyProperty.Value "")
  
    End If
  
  Next

  I hope this helps.

  Good day

  Eva

• path of the file to open data storage

  Hi all!

  Now I am using open data storage blocks, write data and data storage to store and retrieve data from result nearby. For the issue of file path, before I

  Set the path of data by double clicking on the block 'open data storage' and inserting the location of the file in the indicated place, and it worked!

  Now since I made a stand-alone application of this program and use it on other computers, the location of the file that I inserted in the block of open data storage is not

  no more valid in the other PC. So I modified my source code by connecting a 'journey of the current vi' to the node of the file path of the open instead of data storage block

  insert inside the block and this does not work! During the race he displays an error in the data writing block saying that the refnum of storage is not valid!

  I wonder why I couldn't specify the path of the file like this. Kind to allow me to specify the path of the file in the path of the vi?

  Thank you!

  Chao

  You need to account for that path changes when integre integrated application, take a look at this example.

  https://decibel.NI.com/content/docs/doc-4212

• "Storage insufficient to create the shadow copy storage file or other shadow copy data"(0x8004231F). "

  I have Windows Vista Home Premium (32 bit) and you cannot create a system restore point.  Despite all attempts, I keep getting the error message "storage insufficient to create the shadow copy storage file or other shadow copy data"(0x8004231F). "  There is a large hard drive space (90 GB free with)< 70="" gb="" used). ="" how="" can="" this="" be="">

  Hi rebick,.

   

  Welcome to Microsoft Answers Forums.

  We would like to get more information about you to help solve your problem. You better, please answer the following questions.

  • When was the last time it worked?
  • Remember to make changes to the computer recently?

  First of all, I would say that you unplug any external drive connected to the computer except the keyboard and mouse.

  This error message can occur if there is some system files corrupted on your computer. Suggest to run a SFC scan, which would be a search for system files corrupted on the computer and replace them.

  Scan SFC enforcement procedure:

  1. click on the Start button

  2. on the Start Menu, click all programs followed by accessories

  3. in the menu accessories, right-click on command line option

  4. in the drop-down menu that appears, click the "Run as Administrator" option

  5 If you have the enabled User Account Control (UAC) you will be asked to consent to the opening of the command line. You simply press the button continue if you are the administrator or insert password etc.

  6. in the command prompt window, type: sfc/scannow then press enter

  7. a message is displayed to indicate that "the analysis of the system will start.

  8. be patient because the analysis may take some time

  9. If all the files need replace SFC will replace them. You may be asked to insert your Vista DVD for this process to continue

  10. If all goes although you should, after the analysis, see the following message "Windows resource protection not found any breach of integrity.

  11 after the scan finished, close the command prompt window reboot the computer and check.

  The analysis may take some time, so be patient. Windows allows to fix corrupt or missing files it finds. If the information of the installation CD is required to fix the problem, you may be asked to insert your Windows Vista.

  For more information please visit the link below.

  How to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista

  http://support.Microsoft.com/kb/936212

  If the step above does not resolve the issue, I would say that you create a new user on the computer account.

  Log on to the new user account and check if you can create a system restore point.

  1. Open user accounts by clicking the Start button, clicking Control Panel, clicking user accounts and family safety, then clicking on user accounts.
  2. Click on manage another account. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. Click on create a new account.
  4. Type the name you want to assign to the user account, click an account type, and then click on create an account.

   http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Disk groups are not visible cluster. vSAN datastore exists. 2 guests (on 8) cluster do not see the vSAN data store. Their storage is not recognized.

  http://i.imgur.com/pqAXtFl.PNG

  http://i.imgur.com/BnztaDD.PNG

  Do not know how even tear it down and rebuild it if the disk groups are not visible. The discs are in good health on each host storage adapters.

  Currently the latest version of vCenter 5.5. Hosts running 5.5 build 2068190

  Just built. Happy to demolish and rebuild. Just do not know why it is not visible on the two hosts and the disk groups are only recognized 3 guests when more are contributing. Also strange that I can't get the disk groups to fill in vCenter. I tried two different browsers (chrome and IE).

  I have now works.

  All the identical 5.5 relies on ESXi hosts. All hosts are homogeneous CPU/sum of the prospects for disk controller / installed RAM/storage.

  I have work. I had to manually destroy all traces of the vSAN on each single to help host node:

  (1) put the hosts in maintenance mode and remove the cluster. I was unable to disable vSAN in the cluster, I made on each node host (manually via the CLI below) then disconnected web client vCenter and return to finally refresh the ability to disable on the cluster.

  esxcli vsan cluster get - to check the status of each host.

  esxcli vsan cluster drop - the vSAN cluster host.

  storage of vsan esxcli list - view records in the individual host group

  esxcli vsan storage remove-d naa.id_of_magnetic_disks_here - to remove each of the disks in the disk group (you can ignore this using the following command to remove the SSD only falling each disc in this host group).

  esxcli vsan storage remove s naa.id_of_solid_state_disks_here - this is the SSD and all the magnetic disks in a given disk group.

  After that, I was able to manually add hosts to the cluster, leave maintenance mode and configure the disk groups. Aggregated data of the vSAN data store is correct now, and everything is functional.

  Another question for those of you who still read... How to configure such as the VM storage strategy that migrates towards (or inspired) the vSAN data store will immediately resume the default storage policy, I built for VSANs?

  Thanks for anyone who has followed.

• Hello out there! I am trying to understand the relationship between the products. I am a current user of 13 items and sought to CC Photoshop with Lightroom. Always use elements like the storage tool to catalog my photos or it get replaced?

  Hello out there! I am trying to understand the relationship between the products. I am a current user of 13 items and sought to CC Photoshop with Lightroom. Always use elements like the storage tool to catalog my photos or it get replaced?

  It's kind of ridiculous. All I want to do is ask a question and there is no place to connect with anyone. Sucks!

  Hi charlesf,

  If you choose to go to CC Photoshop with Lightroom, Photoshop Elements would not be replaced.

  CC of Photoshop and Photoshop Elements are different programs, so the two will remain separate on your machine and catalogue items would not hit at all.

  Let us know if you have any other questions.

  Kind regards

  Claes